SANYO LC78622E

Ordering number : EN5467
CMOS LSI
LC78622E
Compact Disc Player DSP
Overview
The LC78622E is a CMOS LSI that implements the signal
processing and servo control required by compact disc
players. At the same time as providing an EFM PLL
circuit, a 1-bit D/A converter, and an analog low-pass
filter the LC78622E realizes an optimal cost-performance
tradeoff for low-end players by strictly limiting
functionality to basic signal-processing and servo system
functionality. The LC78622E signal-processing system
provides demodulation of the EFM signal from the pickup,
de-interleaving, error detection and correction, and digital
filters that can prove useful in reducing the cost of end
products. The LC78622E servo control system processes
servo commands sent from the control microprocessor.
Functions
• Input signal processing: The LC78622E takes an HF
signal as input, digitizes (slices) that signal at a precise
level, converts that signal to an EFM signal, and
generates a PLL clock with an average frequency of
4.3218 MHz by comparing the phases of that signal and
an internal VCO.
• Precise reference clock and necessary internal timing
generation using an external 16.9344 MHz crystal
oscillator
• Disk motor speed control using a frame phase difference
signal generated from the playback clock and the
reference clock
• Frame synchronization signal detection, protection and
interpolation to assure stable data readout
• EFM signal demodulation and conversion to 8-bit
symbol data
• Subcode data separation from the EFM demodulated
signal and output of that data to an external
microprocessor
• Subcode Q signal output to a microprocessor over the
serial I/O interface after performing a CRC error check
(LSB first)
• Demodulated EFM signal buffering in internal RAM to
handle up to ±4 frames of disk rotational jitter
• Demodulated EFM signal reordering in the prescribed
order for data unscrambling and de-interleaving
• Error detection, correction, and flag processing (error
correction scheme: dual C1 plus dual C2 correction)
• The LC78622E sets the C2 flags based on the C1 flags
•
•
•
•
•
•
•
•
•
•
•
and a C2 check, and then performs signal interpolation
or muting depending on the C2 flags. The interpolation
circuit uses a dual-interpolation scheme. The previous
value is held if the C2 flags indicate errors two or more
times consecutively.
Support for command input from a control
microprocessor: commands include track jump, focus
start, disk motor start/stop, muting on/off and track
count (8 bit serial input)
Built-in digital output circuits.
Arbitrary track counting to support high-speed data
access
D/A converter outputs with data continuity improved by
4× oversampling digital filters.
Built-in third-order ∑∆ D/A converters (An analog lowpass filter is built in.)
Built-in digital attenuator (8 bits – alpha, 239 steps)
Built-in digital de-emphasis
Zero cross muting
Supports the implementation of a double-speed dubbing
function.
Support for bilingual applications.
General-purpose I/O ports: 5 pins
Features
• 5 V single-voltage power supply
• Supports low-voltage operation (3.0 V, minimum)
Package Dimensions
unit: mm
3159-QFP64E
[LC78622E]
SANYO: QFP64E
SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN
93096HA (OT) No. 5467-1/29
LC78622E
Equivalent Circuit Block Diagram
Pin Assignment
No. 5480-2/29
LC78622E
Specifications
Absolute Maximum Ratings at Ta = 25°C, VSS = 0 V
Parameter
Symbol
Maximum supply voltage
Input voltage
Output voltage
Allowable power dissipation
Ratings
Unit
VDD max
Conditions
VSS – 0.3 to VSS + 7.0
V
VIN
VSS – 0.3 to VDD + 0.3
V
VOUT
VSS – 0.3 to VDD + 0.3
Pd max
300
V
mW
Operating temperature
Topr
–20 to +75
°C
Storage temperature
Tstg
–40 to +125
°C
max
Unit
Allowable Operating Ranges at Ta = 25°C, VSS = 0 V
Parameter
Symbol
Conditions
VDD (1)
VDD, XVDD, LVDD, RVDD, VVDD:
During normal-speed playback
3.0
5.5
V
VDD (2)
VDD, XVDD, LVDD, RVDD, VVDD:
During double-speed playback
3.6
5.5
V
VIH (1)
DEFI, COIN, RES, HFL, TES, SBCK, RWC, CQCK,
TAI, TEST1 to TEST5, CS, CONT1 to CONT5
0.7 VDD
VDD
V
VIH (2)
EFMIN
0.6 VDD
VDD
V
VIL (1)
DEFI, COIN, RES, HFL, TES, SBCK, RWC, CQCK,
TAI, TEST1 to TEST5, CS, CONT1 to CONT5
0
0.3 VDD
V
0
0.4 VDD
Supply voltage
Input high level voltage
Input low level voltage
VIL (2)
EFMIN
min
typ
V
tSU
COIN, RWC: Figure 1
400
ns
Data hold time
tHD
COIN, RWC: Figure 1
400
ns
High level clock pulse width
tWH
SBCK, CQCK: Figures 1, 2 and 3
400
ns
Low level clock pulse width
tWL
SBCK, CQCK: Figures 1, 2 and 3
400
Data read access time
tRAC
SQOUT, PW: Figures 2 and 3
Command transfer time
tRWC
RWC: Figure 1
Subcode Q read enable time
tSQE
WRQ: Figure 2, with no RWC signal
Subcode read cycle time
tSC
SFSY: Figure 3
Subcode read enable time
tSE
SFSY: Figure 3
400
ns
Port input data setup time
tCSU
CONT1 to CONT5, RWC: Figure 4
400
ns
Port input data hold time
tCHD
CONT1 to CONT5, RWC: Figure 4
400
ns
Port input clock setup time
tRCQ
RWC, CQCK: Figure 4
100
Port output data delay time
tCDD
CONT1 to CONT5, RWC: Figure 5
Data setup time
Input level
ns
0
400
1000
ns
ns
11.2
ms
136
µs
ns
1200
ns
VIN (1)
EFMIN: Slice level control
1.0
Vp-p
VIN (2)
XIN: Capacitor-coupled input
1.0
Vp-p
Operating frequency range
fop
EFMIN
Crystal oscillator frequency
fX
XIN, XOUT
10
16.9344
MHz
MHz
No. 5480-3/29
LC78622E
Electrical Characteristics at Ta = 25°C, VDD = 5 V, VSS = 0 V
Parameter
Current drain
Input high level current
Input low level current
Output high level voltage
Symbol
IDD
min
typ
max
Unit
25
35
mA
5
µA
75
µA
IIH (1)
DEFI, EFMIN, COIN, RES, HFL, TES, SBCK,
RWC, CQCK: TEST1: VIN = VDD
IIH (2)
TAI, TEST2 to TEST5, CS: VIN = VDD = 5.5 V
25
DEFI, EFMIN, COIN, RES, HFL, TES, SBCK,
RWC, CQCK: TAI, TEST1 to TEST5, CS: VIN = 0 V
–5
µA
IIL
VOH (1)
EFMO, CLV+, CLV–, V/P, PCK, FSEQ, TOFF,
TGL, JP+, JP–, EMPH, EFLG, FSX: IOH = –1 mA
4
V
VOH (2)
MUTEL, MUTER, C2F, SBSY, PW, SFSY, WRQ,
SQOUT, TST11, 16M, 4.2M, CONT1 to CONT5:
IOH = –0.5 mA
4
V
4.5
V
VOH (3)
DOUT: IOH = –12 mA
VOL (1)
EFMO, CLV+, CLV–, V/P, PCK, FSEQ,
TOFF, TGL, JP+, JP–, EMPH, EFLG, FSX:
IOH = 1 mA
VOL (2)
1
V
MUTEL, MUTER,
C2F, SBSY, PW, SFSY, WRQ, SQOUT,
TST11, 16M, 4.2M, CONT1 to CONT5:
IOH = 2 mA
0.4
V
VOL (3)
DOUT: IOH = 12 mA
0.5
V
IOFF (1)
PDO, CLV+, CLV–, JP+, JP–, CONT1 to CONT5:
VOUT = VDD
5
µA
IOFF (2)
PDO, CLV+, CLV–, JP+, JP–, CONT1 to CONT5:
VOUT = 0 V
Output low level voltage
Output off leakage current
Charge pump output current
Conditions
VDD, XVDD, LVDD, RVDD, VVDD
–5
µA
IPDOH
PDO: RISET = 68 kΩ
64
80
96
µA
IPDOL
PDO: RISET = 68 kΩ
–96
–80
–64
µA
typ
max
Unit
0.011
0.013
%
One-Bit D/A Converter Analog Characteristics
at Ta = 25°C, VDD = LVDD = RVDD = 5 V, VSS = LVSS = RVSS = 0 V
Parameter
Total harmonic distortion
Symbol
THD + N
Conditions
min
LCHO, RCHO; 1 kHz: 0 dB data input,
using the 20 kHz low-pass filter (AD725D built in)
Dynamic range
DR
LCHO, RCHO; 1 kHz: –60 dB data input,
using the 20 kHz low-pass filter and the A filter
(AD725D built in)
91
92
dB
Signal-to-noise ratio
S/N
LCHO, RCHO; 1 kHz: 0 dB data input,
using the 20 kHz low-pass filter and the A filter
(AD725D built in)
93
95
dB
Crosstalk
CT
LCHO, RCHO; 1 kHz: 0 dB data input,
using the 20 kHz low-pass filter (AD725D built in)
82
84
dB
Note: Measured with the normal-speed playback mode in the Sanyo one-bit D/A converter block reference digital attenuator circuit set to EE (hexadecimal).
No. 5480-4/29
LC78622E
Figure 1 Command Input
Figure 2 Subcode Q Output
Figure 3 Subcode Output
No. 5480-5/29
LC78622E
Figure 4 General-Purpose Port Input Timing
Figure 5 General-Purpose Port Output Timing
No. 5480-6/29
LC78622E
Pin Functions
Pin No.
Symbol
I/O
1
DEFI
I
Function
Defect detection signal (DEF) input. (Must be connected to 0 V when unused.)
2
TAI
I
Test input. A pull-down resistor is built in. Must be connected to 0 V.
3
PDO
O
External VCO control phase comparator output
4
VVSS
–
5
ISET
AI
6
VVDD
–
Internal VCO power supply
7
FR
AI
VCO frequency range adjustment
PLL pins
Internal VCO ground. Must be connected to 0 V.
PDO output current adjustment resistor connection
8
VSS
–
9
EFMO
O
10
EFMIN
I
11
TEST2
I
Test input. A pull-down resistor is built in. Must be connected to 0 V.
12
CLV+
O
Disc motor control output.
13
CLV–
O
Three-value output is also possible when specified by microprocessor command.
14
V/P
O
Rough servo/phase control automatic switching monitor output. Outputs a high level during rough servo and a low level
during phase control.
Digital system ground. Must be connected to 0 V.
Slice level control
EFM signal output
EFM signal input
15
HFL
I
Track detection signal input. This is a Schmitt input.
16
TES
I
Tracking error signal input. This is a Schmitt input.
17
TOFF
O
Tracking off output
18
TGL
O
Tracking gain switching output. Increase the gain when low.
19
JP+
O
Track jump output.
20
JP–
O
Three-value output is also possible when specified by microprocessor command.
21
PCK
O
EFM data playback clock monitor. Outputs 4.3218 MHz when the phase is locked.
22
FSEQ
O
Synchronization signal detection output. Outputs a high level when the synchronization signal detected from the EFM
signal and the internally generated synchronization signal agree.
Digital system power supply.
23
VDD
–
24
CONT1
I/O
General-purpose I/O pin 1
25
CONT2
I/O
General-purpose I/O pin 2
26
CONT3
I/O
General-purpose I/O pin 3
27
CONT4
I/O
General-purpose I/O pin 4
28
CONT5
I/O
General-purpose I/O pin 5
29
EMPH
O
De-emphasis monitor pin. A high level indicates playback of a de-emphasis disk.
Controlled by serial data commands from the microprocessor. Any of these that are unused
must be either set up as input ports and connected to 0 V, or set up as output ports and
left open.
30
C2F
O
C2 flag output
31
DOUT
O
Digital output. (EIAJ format)
32
TEST3
I
Test input. A pull-down resistor is built in. Must be connected to 0 V.
33
TEST4
I
Test input. A pull-down resistor is built in. Must be connected to 0 V.
34
N.C.
–
Unused. Must be left open.
35
MUTEL
O
36
LVDD
–
37
LCHO
O
38
LVSS
–
39
RVSS
–
40
RCHO
O
41
RVDD
–
42
MUTER
O
43
XVDD
–
44
XOUT
O
45
XIN
I
Left channel mute output
Left channel
one-bit D/A converter
Left channel power supply
Left channel output
Left channel ground. Must be connected to 0 V.
Right channel ground. Must be connected to 0 V.
Right channel
one-bit D/A converter
Right channel output
Right channel power supply
Right channel mute output
Crystal oscillator power supply.
Connections for a 16.9344 crystal oscillator element
46
XVSS
–
Crystal oscillator ground. Must be connected to 0 V.
47
SBSY
O
Subcode block synchronization signal output
48
EFLG
O
C1, C2, single and double error correction monitor pin
49
PW
O
Subcode P, Q, R, S, T, U, V and W output
50
SFSY
O
Subcode frame synchronization signal output. This signal falls when the subcodes are in the standby state.
No. 5480-7/29
LC78622E
Continued from preceding page.
Pin No.
Symbol
I/O
51
SBCK
I
Subcode readout clock input. This is a Schmitt input. (Must be connected to 0 V when unused.)
Function
52
FSX
O
Output for the 7.35 kHz synchronization signal divided from the crystal oscillator
53
WRQ
O
Subcode Q output standby output
54
RWC
I
Read/write control input. This is a Schmitt input.
55
SQOUT
O
Subcode Q output
56
COIN
I
Command input from the control microprocessor
57
CQCK
I
Input for both the command input clock and the subcode readout clock. This is a Schmitt input.
58
RES
I
Chip reset input. This pin must be set low briefly after power is first applied.
59
TST11
O
Test output. Leave open. (Normally outputs a low level.)
60
16M
O
16.9344 MHz output.
61
4.2M
O
4.2336 MHz output
62
TEST5
I
Test input. A pull-down resistor is built in. Must be connected to 0 V.
63
CS
I
Chip select input. A pull-down resistor is built in. Must be connected to 0 V if not controlled.
64
TEST1
I
Test input. No pull-down resistor. Must be connected to 0 V.
Note: The same potential must be supplied to all power supply pins, i.e., VDD, VVDD, LVDD, RVDD, and XVDD.
Pin Applications
1. HF Signal Input Circuit; Pin 10: EFMIN, pin 9: EFMO, pin 1: DEFI, pin 12: CLV+
An EFM signal (NRZ) sliced at an optimal level can be acquired
by inputting the HF signal to EFMIN.
The LC78622E handles defects as follows. When a high level is
input to the DEFI pin (pin 1), EFMO (pin 9) pins (the slice level
control outputs) go to the high-impedance state, and the slice
level is held. However, note that this function is only valid in
CLV phase control mode, that is, when the V/P pin (pin 14) is
low. This function can be used in combination with the
LA9230M, LA9231M and LA9240M DEF pins.
Note: If the EFMIN and CLV+ signal lines are too close to each
other, unwanted radiation can result in error rate
degradation. We recommend laying a ground or VDD
shield line between these two lines.
2. PLL Clock Generation Circuit; Pin 3: PDO, pin 5: ISET, pin 7: FR, pin 21: PCK
Since the LC78622E includes a VCO circuit, a PLL circuit can
be formed by connecting an external RC circuit. ISET is the
charge pump reference current, PDO is the VCO circuit loop
filter, and FR is a resistor that determines the VCO frequency
range.
(Reference values)
R1 = 68 kΩ, C1 = 0.1 µF
R2 = 680 Ω, C2 = 0.1 µF
R3 = 1.2 kΩ
The VCO × 2 command is an auxiliary command for characteristics guarantee in low-voltage operations. This
command supports the low-voltage operations at VDD = 3.0 to 3.6 V.
No. 5480-8/29
LC78622E
3. VCO Monitor; Pin 21: PCK
PCK is a monitor pin that outputs an average frequency of 4.3218 MHz, which is divided from the VCO frequency.
4. Synchronization Detection Monitor; Pin 22: FSEQ
Pin 22 goes high when the frame synchronization (a positive polarity synchronization signal) from the EFM signal
read in by PCK and the timing generated by the counter (the interpolation synchronization signal) agree. This pin is
thus a synchronization detection monitor. (It is held high for a single frame.)
5. Servo Command Function; Pin 54: RWC, pin 56: COIN, pin 57: CQCK
Commands can be executed by setting RWC high and inputting commands to the COIN pin in synchronization with
the CQCKclock. Note that commands are executed on the falling edge of RWC.
Focus start
Track jump
Muting control
Disk motor control
Miscellaneous control
One-byte commands
Track check
Two-byte command (RWC set twice)
Digital attenuator
General-purpose I/O, E/D
Two-byte commands (RWC set once)
• One-byte commands
• Two-byte commands (RWC set twice: For track checking)
No. 5480-9/29
LC78622E
• Two-byte commands (RWC set once: Sets up the digital attenuation and the general-purpose I/O ports)
• Command noise rejection
MSB
LSB
Command
1 1 1 0 1 1 1 1
COMMAND INPUT NOISE REDUCTION MODE
1 1 1 0 1 1 1 0
RESET NOISE EXCLUSION MODE
RES = low
●
This command reduces the noise on the CQCK clock signal. While this is effective for noise pulses shorter than
500 ns, the CQCK timings tWL, tWH, and tSU, must be set for at least 1 µs.
6. CLV Servo Circuit; Pin 12: CLV+, pin 13: CLV–, pin 14: V/P
MSB
LSB
Command
0 0 0 0 0 1 0 0
DISC MOTOR START (accelerate)
0 0 0 0 0 1 0 1
DISC MOTOR CLV (CLV)
0 0 0 0 0 1 1 0
DISC MOTOR BRAKE (decelerate)
0 0 0 0 0 1 1 1
DISC MOTOR STOP (stop)
RES = low
●
The CLV+ pin provides the signal that accelerates the disk in the forward direction and the CLV– pin provides the
signal that decelerates the disk. Commands from the control microprocessor select one of four modes; accelerate,
decelerate, CLV and stop. The table below lists the CLV+ and CLV– outputs in each of these modes.
Mode
CLV+
CLV–
Accelerate
High
Low
Decelerate
Low
High
CLV
Pulse output
Pulse output
Stop
Low
Low
Note: CLV servo control commands can set the TOFF pin low only in CLV mode. That pin will be at the high level
at all other times. Control of the TOFF pin by microprocessor command is only valid in CLV mode.
No. 5480-10/29
LC78622E
• CLV mode
In CLV mode the LC78622E detects the disk speed from the HF signal and provides proper linear speed using
several different control schemes by switching the DSP internal modes. The PWM reference period corresponds to
a frequency of 7.35 kHz. The V/P pin outputs a high level during rough servo and a low level during phase control.
Internal mode
Rough servo (velocity too low)
Rough servo (velocity too high)
Phase control (PCK locked)
CLV+
CLV–
V/P
High
Low
High
Low
High
High
PWM
PWM
Low
• Rough servo gain switching
MSB
LSB
Command
1 0 1 0 1 0 0 0
DISC 8 SET
1 0 1 0 1 0 0 1
DISC 12 SET
RES = low
●
For 8 cm disks, the rough servo mode CLV control gain can be set about 8.5 dB lower than the gain used for 12 cm
disks.
• Phase control gain switching
MSB
LSB
Command
1 0 1 1 0 0 0 1
CLV PHASE COMPARATOR DIVISOR: 1/2
1 0 1 1 0 0 1 0
CLV PHASE COMPARATOR DIVISOR: 1/4
1 0 1 1 0 0 1 1
CLV PHASE COMPARATOR DIVISOR: 1/8
1 0 1 1 0 0 0 0
NO CLV PHASE COMPARATOR DIVISOR USED
RES= low
●
The phase control gain can be changed by changing the divisor used by the dividers in the stage immediately
preceding the phase comparator.
No. 5480-11/29
LC78622E
• CLV three-value output
MSB
LSB
Command
1 0 1 1 0 1 0 0
CLV THREE VALUE OUTPUT
1 0 1 1 0 1 0 1
CLV TWO VALUE OUTPUT
(the scheme used by previous products)
RES = low
●
The CLV three-value output command allows the CLV to be controlled by a single pin.
• Internal brake modes
MSB
LSB
1 1 0 0 0 1 0 1
Command
RES = low
INTERNAL BRAKE ON
1 1 0 0 0 1 0 0
INTERNAL BRAKE OFF
1 0 1 0 0 0 1 1
INTERNAL BRAKE CONTROL
1 1 0 0 1 0 1 1
INTERNAL BRAKE CONTINUOUS MODE
1 1 0 0 1 0 1 0
RESET CONTINUOUS MODE
1 1 0 0 1 1 0 1
TON MODE DURING INTERNAL BRAKING
1 1 0 0 1 1 0 0
RESET TON MODE
●
●
●
— Issuing the internal brake-on (C5H) command sets the LC78622E to internal brake mode. In this mode, the disk
deceleration state can be monitored from the WRQ pin when a brake command (06H) is executed.
— In this mode the disk deceleration state is determined by counting the EFM signal density in a single frame, and
when the EFM signal count falls under four, the CLV– pin is dropped to low. At the same time the WRQ signal,
which functions as a brake completion monitor, goes high. When the microprocessor detects a high level on the
WRQ signal, it should issue a STOP command to fully stop the disk. In internal brake continuous mode (CBH),
the CLV– pin high-level output braking operation continues even after the WRQ brake completion monitor
goes high.
Note that if errors occur in deceleration state determination due to noise in the EFM signal, the problem may be
rectified by changing the EFM signal count from four to eight with the internal brake control command (A3H).
— In TOFF output disabled mode (CDH), the TOFF pin is held low during internal brake operations. We
recommend using this feature, since it is effective at preventing incorrect detection at the disk mirror surface.
No. 5480-12/29
LC78622E
Note: 1. If focus is lost during the execution of an internal brake command, the pickup must first be refocussed
and then the internal brake command must be reissued.
2. Since incorrect deceleration state determination is possible depending on the EFM signal playback state
(e.g., disk defects, access in progress), we recommend using these functions in combination with a
microprocessor.
7. Track Jump Circuit; Pin 15: HFL, pin 16: TES, pin 17: TOFF, pin 18: TGL, pin 19: JP+, pin 20: JP–
• The LC78622E supports the two track count modes listed below.
MSB
Command
RES = low
0 0 1 0 0 0 1 0
LSB
NEW TRACK COUNT (using the TES/HFL combination)
●
0 0 1 0 0 0 1 1
STANDARD TRACK COUNT (directly counts the TES signal)
The earlier track count function uses the TES signal directly as the internal track counter clock.
To reduce counting errors resulting from noise on the rising and falling edges of the TES signal, the new track
count function prevents noise induced errors by using the combination of the TES and HFL signals, and
implements a more reliable track count function. However, dirt and scratches on the disk can result in HFL signal
dropouts that may result in missing track count pulses. Thus care is required when using this function.
No. 5480-13/29
LC78622E
• TJ commands
MSB
LSB
Command
1 0 1 0 0 0 0 0
STANDARD TRACK JUMP
1 0 1 0 0 0 0 1
NEW TRACK JUMP
0 0 0 1 0 0 0 1
1 TRACK JUMP IN #1
0 0 0 1 0 0 1 0
1 TRACK JUMP IN #2
0 0 1 1 0 0 0 1
1 TRACK JUMP IN #3
0 1 0 1 0 0 1 0
1 TRACK JUMP IN #4
0 0 0 1 0 0 0 0
2 TRACK JUMP IN
0 0 0 1 0 0 1 1
4 TRACK JUMP IN
0 0 0 1 0 1 0 0
16 TRACK JUMP IN
0 0 1 1 0 0 0 0
32 TRACK JUMP IN
0 0 0 1 0 1 0 1
64 TRACK JUMP IN
0 0 0 1 0 1 1 1
128 TRACK JUMP IN
0 0 0 1 1 0 0 1
1 TRACK JUMP OUT #1
0 0 0 1 1 0 1 0
1 TRACK JUMP OUT #2
0 0 1 1 1 0 0 1
1 TRACK JUMP OUT #3
0 1 0 1 1 0 1 0
1 TRACK JUMP OUT #4
0 0 0 1 1 0 0 0
2 TRACK JUMP OUT
0 0 0 1 1 0 1 1
4 TRACK JUMP OUT
0 0 0 1 1 1 0 0
16 TRACK JUMP OUT
0 0 1 1 1 0 0 0
32 TRACK JUMP OUT
0 0 0 1 1 1 0 1
64 TRACK JUMP OUT
0 0 0 1 1 1 1 1
128 TRACK JUMP OUT
0 0 0 1 0 1 1 0
256 TRACK CHECK
0 0 0 0 1 1 1 1
TOFF
1 0 0 0 1 1 1 1
TON
1 0 0 0 1 1 0 0
TRACK JUMP BRAKE
0 0 1 0 0 0 0 1
TOFF OUTPUT MODE DURING JP PULSE PERIOD
0 0 1 0 0 0 0 0
RESET TOFF OUTPUT MODE DURING JP PULSE PERIOD
RES = low
●
●
●
When the LC78622E receives a track jump instruction as a servo command, it first generates accelerating pulses
(period a) and next generates deceleration pulses (period b). The passage of the braking period (period c) completes
the specified jump. During the braking period, the LC78622E detects the beam slip direction from the TES and
HFL inputs. TOFF is used to cut the components in the TES signal that aggravate slip. The jump destination track
is captured by increasing the servo gain with TGL. In during TOFF output mode JP pulse period the TOFF signal
is held high during the JP pulse generation period.
Note: Of the modes related to disk motor control, the TOFF pin only goes low in CLV mode, and will be high
during accelerate, stop, and decelerate modes.Note that the TOFF pin can be turned on and off
independently by microprocessor issued commands. However, this function is only valid when disk motor
control is in CLV mode.
No. 5480-14/29
LC78622E
• Track jump modes
The table lists the relationships between acceleration pulses (the a period) , deceleration pulses (the b period), and
the braking period (the c period).
Standard track jump mode
Command
a
b
New track jump mode
c
a
b
c
1 TRACK JUMP IN (OUT) #1
233 µs
233 µs
60 ms
233 µs
233 µs
60 ms
1 TRACK JUMP IN (OUT) #2
0.5 track
jump period
233 µs
60 ms
0.5 track
jump period
The same
time as “a”
60 ms
1 TRACK JUMP IN (OUT) #3
0.5 track
jump period
233 µs
This period does
not exist.
0.5 track
jump period
The same
time as “a”
This period does
not exist.
1 TRACK JUMP IN (OUT) #4
0.5 track
jump period
233 µs
60 ms; TOFF is
low during
the C period.
0.5 track
jump period
The same
time as “a”
60 ms; TOFF is
low during
the C period.
2 TRACK JUMP IN (OUT)
None
None
None
1 track
jump period
The same
time as “a”
60 ms
4 TRACK JUMP IN (OUT)
2 track
jump period
466 µs
60 ms
2 track
jump period
The same
time as “a”
60 ms
16 TRACK JUMP IN (OUT)
9 track
jump period
7 track
jump period
60 ms
9 track
jump period
The same
time as “a”
60 ms
32 TRACK JUMP IN (OUT)
18 track
jump period
14 track
jump period
60 ms
18 track
jump period
14 track
jump period
60 ms
64 TRACK JUMP IN (OUT)
36 track
jump period
28 track
jump period
60 ms
36 track
jump period
28 track
jump period
60 ms
128 TRACK JUMP IN (OUT)
72 track
jump period
56 track
jump period
60 ms
72 track
jump period
56 track
jump period
60 ms
256 TRACK CHECK
TOFF goes high during the period
when 256 tracks are passed over.
The a and b pulses are not output.
60 ms
TOFF goes high during the period
when 256 tracks are passed over.
The a and b pulses are not output.
60 ms
TRACK JUMP BRAKE
There are no a or b periods.
60ms
There are no a and b periods.
60 ms
Note: 1. As indicated in the table, actuator signals are not output during the 256 TRACK CHECK function. This is a mode in which the TES signal is counted
in the tracking loop off state. Therefore, feed motor forwarding is required.
2. The servo command register is automatically reset after one cycle of the track jump sequence (a, b, c) completes.
3. If another track jump command is issued during a track jump operation, the content of that new command will be executed starting immediately.
4. The 1 TRACK JUMP #3 mode does not have a braking period (the C period). Since brake mode must be generated by an external circuit, care is
required when using this mode.
5. While there was no braking period (the C period) in the LC78620E/21E for the new track jump command “2 TRACK JUMP IN (OUT)”, this has been
changed in this LSI, which has a C period of 60 ms.
The THLD signal is generated by the LA9230M, LA9231M, or LA9240M, and the tracking signal is held during the JP pulse period.
No. 5480-15/29
LC78622E
5.
Tracking brake
The chart shows the relationships between the TES, HFL, and TOFF signals during the track jump C period. The TOFF signal is extracted from the
HFL signal by TES signal edges. When the HFL signal is high, the pickup is over the mirror surface, and when low, the pickup is over data bits.
Thus braking is applied based on the TOFF signal being high when the pickup is moving from a mirror region to a data region and being low when
the pickup is moving from a data region to a mirror region.
• JP three-value output
MSB
LSB
Command
1 0 1 1 0 1 1 0
JP THREE VALUE OUTPUT
1 0 1 1 0 1 1 1
JP TWO VALUE OUTPUT (earlier scheme)
RES = low
●
The JP three-value output command allows the track jump operation to be controlled from a single pin.
• Track check mode
MSB
LSB
Command
1 1 1 1 0 0 0 0
TRACK CHECK IN
1 1 1 1 1 0 0 0
TRACK CHECK OUT
1 1 1 1 1 1 1 1
TWO BYTE COMMAND RESET
RES = low
●
The LC78622E will count the specified number of tracks minus one when the microprocessor sends an arbitrary
binary value in the range 8 to 254 after issuing either a track check in or a track check out command.
No. 5480-16/29
LC78622E
Note: 1. When the desired track count has been input in binary, the track check operation is started by the fall of RWC.
2. During a track check operation the TOFF pin goes high and the tracking loop is turned off. Therefore, feed motor forwarding is required.
3. When a track check in/out command is issued the function of the WRQ signal switches from the normal mode subcode Q standby monitor function
to the track check monitor function. This signal goes high when the track check is half completed, and goes low when the check finishes. The
control microprocessor should monitor this signal for a low level to determine when the track check completes.
4. If a two-byte reset command is not issued, the track check operation will repeat. That is, to skip over 20,000 tracks, issue a track check 201
command once, and then count the WRQ signal 100 times. This will check 20,000 tracks.
5. After performing a track check operation, use the brake command to have the pickup lock onto the track.
8. Error Flag Output; Pin 48: EFLG, pin 52: FSX
The FSX signal is generated by dividing the crystal oscillator clock, and is a 7.35 kHz frame synchronization signal.
The error correction state for each frame is output from EFLG. The FSX low-level period indicates the C1 correction
state, and the high-level period indicates the C2 correction state. The playback OK/NG state can be easily determined
from the extent of the high level that appears here.
9. Subcode P, Q and R to W Output Circuit; Pin 49: PW, pin 47: SBSY, pin 50: SFSY, pin 51: SBCK
PW is the subcode signal output pin, and all the codes, P, Q, and R to W can be read out by sending eight clocks to
the SBCK pin within 136 µs after the fall of SFSY. The signal that appears on the PW pin changes on the rising edge
of SBCK. If a clock is not applied to SBCK, the P code will be output from PW. SFSY is a signal that is output for
each subcode frame cycle, and the falling edge of this signal indicates standby for the output of the subcode symbol
(P to W). Subcode data P is output on the fall of this signal.
SBSY is a signal output for each subcode block. This signal goes high for the S0 and S1 synchronization signals. The
fall of this signal indicates the end of the subcode synchronization signals and the start of the data in the subcode
block. (EIAJ format)
No. 5480-17/29
LC78622E
10. Subcode Q Output Circuit; Pin 53: WRQ, pin 54: RWC, pin 55: SQOUT, pin 57: CQCK, pin 63: CS
MSB
LSB
Command
0 0 0 0 1 0 0 1
ADDRESS FREE
1 0 0 0 1 0 0 1
ADDRESS 1
RES = low
●
Subcode Q can be read from the SQOUT pin by applying a clock to the CQCKpin.
Of the eight bits in the subcode, the Q signal is used for song (track) access and display. The WRQ will be high only if
the data passed the CRC error check and the subcode Q format internal address is 1*. The control microprocessor can
read out data from SQOUT in the order shown below by detecting this high level and applying CQCK. When CQCK
is applied the DSP disables register update internally. The microprocessor should give update permission by setting
RWC high briefly after reading has completed. WRQ will fall to low at this time. Since WRQ falls to low 11.2 ms
after going high, CQCK must be applied during the high period. Note that data is read out in an LSB first format.
Note: * That state will be ignored if an address free command is input. This is provided to handle CD-ROM
applications.
Note: 1. Normally, the WRQ pin indicates the subcode Q standby state. However, it is used for a different monitoring purpose in track check mode and
during internal braking. (See the items on track counting and internal braking for details.)
2. The LC78622E becomes active when the CS pin is low, and subcode Q data is output from the SQOUT pin. When the CS pin is high, the SQOUT
pin goes to the high-impedance state.
No. 5480-18/29
LC78622E
11. Bilingual Function
MSB
Command
RES = low
0 0 1 0 1 0 0 0
LSB
STO CONT
●
0 0 1 0 1 0 0 1
Lch CONT
0 0 1 0 1 0 1 0
Rch CONT
• Following a reset or when a stereo (28H) command has been issued, the left and right channel data is output to the
left and right channels respectively.
• When an Lch set (29H) command is issued, the left and right channels both output the left channel data.
• When an Rch set (2AH) command is issued, the left and right channels both output the right channel data.
12. De-Emphasis; Pin 29: EMPH
The preemphasis on/off bit in the subcode Q control information is output from the EMPH pin. When this pin is
high, the LC78622E internal de-emphasis circuit operates and the digital filters and the D/A converter output deemphasized data.
13. Digital Attenuator
Digital attenuation can be applied to the audio data by setting the RWC pin high and inputting the corresponding
two-byte command to the COIN pin in synchronization with the CQCK clock.
MSB
LSB
Command
1 0 0 0 0 0 0 1
ATT DATA SET
1 0 0 0 0 0 1 0
ATT 4 STEP UP
1 0 0 0 0 0 1 1
ATT 4 STEP DOWN
1 0 0 0 0 1 0 0
ATT 8 STEP UP
1 0 0 0 0 1 0 1
ATT 8 STEP DOWN
1 0 0 0 0 1 1 0
ATT 16 STEP UP
1 0 0 0 0 1 1 1
ATT 16 STEP DOWN
RES = low
DATA 00H set
(MUTE –∞ dB)
• Attenuation setup
Since the attenuation level is set to the muted state (a muting of –∞ is specified by an attenuation coefficient of
00H) after the attenuation level is reset, the attenuation coefficient must be directly set to EEH (using the ATT
DATA SET command) to output audio signals. Note that the attenuation level can be set to one of 239 values from
00H to EEH.
These two-byte commands differ from the two-byte commands used for track counting in that it is only necessary
to set RWC once and a two-byte command reset is not required. After inputting the target attenuation level as a
value in the range 00H to EEH, sending an attenuator step up/down command will cause the attenuation level to
approach the target value in steps of 4, 8, or 16 units as specified in synchronization with rising edges on the LRSY
input. However, the ATT DATA SET command sets the target value directly. If a new data value is input during
the transition, the value begins to approach the new target value at that point. Note that the UP/DOWN distinction
is significant here.
No. 5480-19/29
LC78622E
Audio output level = 20 log
ATT DATA
[dB]
For example, the formula below calculates the time required for the attenuation level to increase from 00H to EEH
when a 4STEP UP command is executed. Note that the control microprocessor must provide enough of a time
margin for this operation to complete before issuing the next attenuation level set command.
238 level × 4STEP UP
≈ 21.6 ms
44.1 kHz
Note: Setting the attenuation level to values of EFH or higher is disallowed to prevent overflows in one-bit D/A
converter calculations from causing noise.
14. Mute Output; Pin 35: MUTEL, pin 42: MUTER
15. C2 Flag Output; Pin 30: C2F
C2F output flag information in 8-bit units.
16. Digital Output Circuit; Pin 31: DOUT
This is an output pin for use with a digital audio interface. Data is output in the EIAJ format. This signal has been
processed by the interpolation and muting circuits. This pin has a built-in driver circuit and can directly drive a
transformer.
MSB
Command
RES = low
0 1 0 0 0 0 1 0
LSB
DOUT ON
●
0 1 0 0 0 0 1 1
DOUT OFF
0 1 0 0 0 0 0 0
UBIT ON
0 1 0 0 0 0 0 1
UBIT OFF
1 0 0 0 1 0 0 0
CDROM-XA
1 0 0 0 1 0 1 1
ROMXA-RST
●
●
• The DOUT pin can be locked at the low level by issuing a DOUT OFF command.
• The UBIT information in the DOUT data can be locked at zero by issuing a UBIT OFF command.
• The DOUT data can be switched to data for which interpolation and muting processing have not been performed
by issuing a CD-ROM XA command.
17. Mute Control Circuit
MSB
LSB
Command
0 0 0 0 0 0 0 1
MUTE: 0 dB
0 0 0 0 0 0 1 1
MUTE: –∞ dB
RES = low
●
Inputting the above command mutes the audio level (MUTE -∞ dB). Since zero-cross muting is used, there is very
little noise associated with this operation. The IC defines zero cross to be the ranges where the upper 7 bits of the
data are all zeros or all ones. Note that the MUTE -12 dB instruction supported by the LC78620E has been removed
from this product.
No. 5480-20/29
LC78622E
18. Interpolation Circuit
Outputting incorrect audio data that could not be corrected by the error detection and correction circuit would result
in loud noises being output. To minimize this noise, the LC78622E replaces the incorrect data with linearly
interpolated data based on the correct data on either side of the incorrect data. If one set of C2 flags indicate errors,
the above replacement is performed, and if two or more sets of C2 flags indicate errors, the IC holds the previous
value. However, when correct data is output following two or more consecutive C2 flags indicating errors, the data
point between the correct data and the data output two points previously (the held value) is replaced with a value
computed by linearly interpolating those two values.
19. General-Purpose I/O Ports; Pin 24: CONT1, Pin 25: CONT2, Pin 26: CONT3, Pin 27: CONT4, Pin 28: CONT5
The LC78622E provides the five CONT1 to CONT5 I/O ports. These are all set to function as input pins after a reset.
Unused port pins should be either connected to ground or set to the output port function.
MSB
LSB
Command
RES = low
1 1 0 1 1 1 0 1
PORT READ
1 1 0 1 1 0 1 1
PORT OP-E/D SET
1 1 0 1 1 1 0 0
PORT DATA SET
PORT I SET
Port data is read in by the PORT READ command in synchronization with the falling edge of the CQCK pin by the
SQOUT pin in the order CONT1 to CONT5. This command is a single-byte command.
Additionally, these ports can be set up individually to function as control output pins with the PORT OP-E/D SET
command. The ports are selected using the lower 5 bits of the 1Byte data. The bits in the data correspond to CONT1
to CONT5 in order starting with the LSB of the 1Byte data. This command is a Two- byte command. (RWC set
once)
MSB
LSB
1 1 0 1 1 0 1 1 X X X d5 d4 d3 d2 d1
Command
PORT OP-E/D SET
dn =1 ... Sets CONTn to be an output pin
dn =0 ... Sets CONTn to be an input pin
X... don’t care
No. 5480-21/29
LC78622E
Ports set to be output pins can output high or low levels independently. The lower 5 bits of the 1 Byte data
correspond to those ports. The bits in the data correspond to CONT1 to CONT5 in order starting with the LSB of the
1 Byte data. This command is a two-byte command. (RWC set once)
MSB
LSB
Command
1 1 0 1 1 1 0 0 X X X d5 d4 d3 d2 d1
PORT DATA SET
dn =1 ... Sets CONTn to be an output pin
dn =0 ... Sets CONTn to be an input pin
X... don’t care
20.
Clock Oscillator; Pin 45: XIN, pin 44: XOUT
MSB
LSB
Command
1 0 0 0 1 1 1 0
OSC ON
1 0 0 0 1 1 0 1
OSC OFF
1 1 0 0 1 1 1 0
XTAL 16M
1 1 0 0 0 0 1 0
NORMAL-SPEED PLAYBACK
1 1 0 0 0 0 0 1
DOUBLE-SPEED PLAYBACK
RES = low
●
●
●
The clock that is used as the time base is generated by connecting a 16.9344 MHz oscillator element between these
pins. The OSC OFF command turns off both the VCO and crystal oscillators. The system control microprocessor can
issue double-speed or normal-speed playback command when the application implements double-speed playback
system.
21. 16M and 4.2M Pins; Pin 60: 16M, pin 61: 4.2M
Both in normal- and double-speed playback modes, the 16M pin buffer outputs the 16.9344 MHz external crystal
oscillator 16.9344 MHz signal. The 4.2M pin supplies the LA9230M, LA9231M or LA9240M system clock, normally
outputting a 4.2336 MHz signal. When the oscillator is turned off both these pins will be fixed at either high or low.
No. 5480-22/29
LC78622E
22. Reset Circuit; Pin 58: RES
When power is first applied, this pin should be briefly set low and then set high. This will set the muting to –∞ dB
and stop the disk motor.
Constant linear velocity servo
START
STOP
0 dB
–∞
Q subcode address conditions
Address 1
Address free
Track jump mode
Standard
New
Track count mode
Standard
New
Digital attenuator
DATA 0
DATA 00H to EEH
ON
OFF
Normal speed
Double speed
ON
OFF
Muting control
OSC
Playback speed
Digital filter normal speed
BRAKE
CLV
Setting the RES pin low sets the LC78622E to the settings enclosed in boxes in the table.
23. Other Pins; Pin 2:TAI, pin 64: TEST1, pin 11: TEST2, pin 32: TEST3, pin 33: TEST4, pin 62: TEST5, pin 59:
TST11
These pins are used for testing the LSI’s internal circuits. Even though pull-down resistors are built into the TAI and
TEST2 to TEST5 input pin circuits, these pins must be connected to 0 V during normal operation. TST11 is an output
pin and should normally be left open.
No. 5480-23/29
LC78622E
24. Circuit Block Operating Descriptions
• RAM address control
The LC78622E incorporates an 8-bit × 2k-word RAM on chip. This RAM has an EFM demodulated data jitter
handling capacity of ±4 frames implemented using address control. The LC78622E continuously checks the remaining
buffer capacity and controls the data write address to fall in the center of the buffer capacity by making fine
adjustments to the frequency divisor in the PCK side of the CLV servo circuit. If the ±4 frame buffer capacity is
exceeded, the LC78622E forcibly sets the write address to the ±0 position. However, since the errors that occur due to
this operation cannot be handled with error flag processing, the IC applies muting to the output for a 128 frame period.
Position
–4 or less
–3
Division ratio or processing
Force to ±0
589
–2
589
–1
589
±0
588
+1
587
+2
587
+3
587
+4 or more
Increase ratio
Standard ratio
Decrease ratio
Force to ±0
• C1 and C2 Error Correction
The LC78622E writes EFM demodulated data to internal RAM to compensate for jitter and then performs the
following processing with uniform timing based on the crystal oscillator clock. First, the LC78622E performs C1
error checking and correction in the C1 block, determines the C1 flags, and writes the C1 flag register. Next, the
LC78622E performs C2 error checking and correction in the C2 block, determines the C2 flags, and writes data to
internal RAM.
C1 flag
Error correction and flag processing
No errors
No correction required · Flag reset
1 error
Correction · Flag reset
2 errors
Correction · Flag set
3 errors or more
Correction not possible · Flag set
C2 flag
Error correction and flag processing
No errors
No correction required · Flag reset
1 error
Correction · Flag reset
2 errors
Depends on C1 flags*1
3 errors or more
Depends on C1 flags*2
Note: 1. If the positions of the errors determined by the C2 check agree with those specified by the C1 flags, the correction is performed and the flags
are cleared. However, if the number of C1 flags is 7 or higher, C2 correction may fail. In this case correction is not performed and the C1 flags
are taken as the C2 flags without change. Error correction is not possible if one error position agrees and the other does not. Furthermore, if
the number of C1 flags is 5 or under, the C1 check result can be seen as unreliable. Accordingly, the flags will be set in this case. Cases
where the number of C1 flags is 6 or more are handled in the same way, and the C1 flags are taken as the C2 flags without change. When
there is not even one agreement between the error positions, error correction is, of course, impossible. Here, if the number of C1 flags was 2
or under, data that was seen as correct after C1 correction is now seen as incorrect data. The flags are set in this case. In other cases, the C1
flags are taken as the C2 flags without change.
2. When data is determined to have three or more errors and be uncorrectable, correction is, of course, impossible. Here, if the number of C1
flags was 2 or under, data that was seen as correct after C1 correction is now seen as incorrect data. The flags are set in this case. In other
cases the C1 flags are taken as the C2 flags without change
No. 5480-24/29
LC78622E
25. Command Summary Table
Blank entry: Illegal command, #: Changed or added command, *: Latching commands (mode setting commands),
●: Commands shared with an ASP (LA9220M/30M/31M or other processor), Items in parentheses are ASP commands
(provided for reference purposes)
00000000
(ADJ.reset)
0 0 0 0 0 0 0 1 * MUTE
0 dB
00000010 #
0 0 0 0 0 0 1 1 * MUTE
–∞ dB
0 0 1 0 0 0 0 0 * TOFF low in
TJ mode
01000000
* UBIT ON
01100000
0 0 1 0 0 0 0 1 * TOFF high in
TJ mode
01000001
* UBIT OFF
01100001
0 0 1 0 0 0 1 0 * New TRACK
COUNT
01000010
* DOUT ON
01100010
0 0 1 0 0 0 1 1 * Old TRACK
COUNT
01000011
* DOUT OFF
01100011
0 0 0 0 0 1 0 0 * DISC MTR START 0 0 1 0 0 1 0 0
01000100
01100100
0 0 0 0 0 1 0 1 * DISC MTR CLV
00100101
01000101
01100101
0 0 0 0 0 1 1 0 * DISC MTR BRAKE 0 0 1 0 0 1 1 0
01000110
01100110
0 0 0 0 0 1 1 1 * DISC MTR STOP
00100111
01000111
01100111
0 0 0 0 1 0 0 0 ● FOCUS START
#1
0 0 1 0 1 0 0 0 * STO CONT
01001000
01101000
0 0 0 0 1 0 0 1 * ADDRESS FREE
0 0 1 0 1 0 0 1 * LCH CONT
01001001
01101001
00001010 #
0 0 1 0 1 0 1 0 * RCH CONT
01001010
01101010
00001011
00101011 #
01001011
01101011 #
00001100
00101100 #
01001100
01101100 #
00001101
00101101 #
01001101
01101101
00001110 #
00101110 #
01001110
0 1 1 0 1 1 1 0 *DF normal speed
off
0 0 0 0 1 1 1 1 * TRACKING OFF
00101111
01001111
01101111 #
00010000
2TJ
IN
00110000
32TJ
IN
01010000
01110000
00010001
1TJ
IN #1
00110001
1TJ
IN #3
01010001
00010010
1TJ
IN #2
00110010
01010010
00010011
4TJ
IN
00110011
01010011
01110011
00010100
16TJ
IN
00110100
01010100
01110100
00010101
64TJ
IN
00110101
01010101
01110101
00010110
256TC
00110110
01010110
01110110
00010111
128TJ IN
00110111
01010111
01110111
00011000
2TJ
OUT
00111000
32TJ
OUT
01011000
01111000
00011001
1TJ
OUT #1
00111001
1TJ
OUT #3
01011001
00011010
1TJ
OUT #2
00111010
01011010
00011011
4TJ
OUT
00111011
01011011
01111011
00011100
16TJ
OUT
00111100
01011100
01111100
00011101
64TJ
OUT
00111101
01011101
01111101
00111110
01011110
01111110
00111111
01011111
01111111
00011110
00011111
128TJ OUT
01110001
1TJ
IN #4
01110010
01111001
1TJ
OUT #4
01111010
Continued on next page.
No. 5480-25/29
LC78622E
Continued from preceding page.
Blank entry: Illegal command, #: Changed or added command, *: Latching commands (mode setting commands),
●: Commands shared with an ASP (LA9220M/30M/31M or other processor), Items in parentheses are ASP commands
(provided for reference purposes)
10000000
1 0 1 0 0 0 0 0 * Old TRK JMP
11000000
1 0 0 0 0 0 0 1 * ATT DATA SET
1 0 1 0 0 0 0 1 * New TRK JMP
11000001
* Double-speed
playback
11100001
1 0 0 0 0 0 1 0 * ATT 4STP UP
10100010
FOCUS START #2 1 1 0 0 0 0 1 0
* Normal-speed
playback
11100010
1 0 0 0 0 0 1 1 * ATT 4STP DWN
1 0 1 0 0 0 1 1 * Internal BRAKE
CONT
11000011
1 0 0 0 0 1 0 0 * ATT 8STP UP
10100100
11000100
* Internal BRK OFF
11100100
1 0 0 0 0 1 0 1 * ATT 8STP DWN
10100101
11000101
* Internal BRK ON
11100101
1 0 0 0 0 1 1 0 * ATT 16STP UP
10100110
11000110
1 0 0 0 0 1 1 1 * ATT 16STP DWN
10100111
11000111
1 0 0 0 1 0 0 0 * #CDROMXA
1 0 1 0 1 0 0 0 * DISC 8 SET
11001000
#
11101000
1 0 0 0 1 0 0 1 * ADDRESS 1
1 0 1 0 1 0 0 1 * DISC 12 SET
11001001
*#
11101001
10001010 #
10101010
11001010
* Internal BRK-DMC 1 1 1 0 1 0 1 0
low
1 0 0 0 1 0 1 1 * #ROMXA
RST
10101011
11001011
* Internal BRK-DMC 1 1 1 0 1 0 1 1
high
10001100
1 0 1 0 1 1 0 0 #VCO X2 SET
11001100
* TOFF during
internal BRAKE
11101100
1 0 0 0 1 1 0 1 * OSC OFF
1 0 1 0 1 1 0 1 #VCO X1 SET
11001101
* TON during
internal BRAKE
11101101
1 0 0 0 1 1 1 0 * OSC ON
10101110
11001110
* Xtal 16M
1 1 1 0 1 1 1 0 * Command noise
rejecter OFF
1 0 0 0 1 1 1 1 * TRACKING ON
10101111
11001111
1 1 1 0 1 1 1 1 * Command noise
rejecter ON
1 0 0 1 0 0 0 0 (* F.OFF.ADJ.ST)
1 0 1 1 0 0 0 0 * CLV-PH 1/1 mode
11010000
1 1 1 1 0 0 0 0 * ● TRCK CHECK
IN
(2BYTE DETECT)
1 0 0 1 0 0 0 1 (* F.OFF.ADJ.OFF)
1 0 1 1 0 0 0 1 * CLV-PH 1/2 mode
11010001
11110001
1 0 0 1 0 0 1 0 (* T.OFF.ADJ.ST)
1 0 1 1 0 0 1 0 * CLV-PH 1/4 mode
11010010
11110010
1 0 0 1 0 0 1 1 (* T.OFF.ADJ.OFF)
1 0 1 1 0 0 1 1 * CLV-PH 1/8 mode
11010011
11110011
1 0 0 1 0 1 0 0 (* LSR.ON)
1 0 1 1 0 1 0 0 * CLV3ST output ON 1 1 0 1 0 1 0 0
11110100
TRACK JMP BRK
11100000
11100011
11100110
11100111
1 0 0 1 0 1 0 1 (* LSR.OF/F.SV.ON) 1 0 1 1 0 1 0 1 * CLV3ST output
OFF
11010101
11110101
1 0 0 1 0 1 1 0 (* LSR.OF/F.SV.OF) 1 0 1 1 0 1 1 0 * JP3ST output ON
11010110
11110110
1 0 0 1 0 1 1 1 (* SP.8CM)
1 0 1 1 0 1 1 1 * JP3ST output OFF 1 1 0 1 0 1 1 1
11110111
1 0 0 1 1 0 0 0 (* SP.12CM)
10111000
11011000
1 1 1 1 1 0 0 0 * ● TRCK CHECK
OUT
(2BYTE DETECT)
1 0 0 1 1 0 0 1 (* SP.OFF)
10111001
11011001
11111001
1 0 0 1 1 0 1 0 (* SLED.ON)
10111010
11011010
11111010
1 0 0 1 1 0 1 1 (* SLED.OFF)
10111011
11011011
#PORT OP-ED SET 1 1 1 1 1 0 1 1
1 0 0 1 1 1 0 0 (* EF.BAL.START)
10111100
11011100
#PORT DATA SET
11111100
1 0 0 1 1 1 0 1 (* T.SERVO.OFF)
10111101
11011101
#PORT READ
11111101
1 0 0 1 1 1 1 0 (* T.SERVO.ON)
10111110
11011110
1 1 1 1 1 1 1 0 ● NOTHING
10011111
10111111
11011111
1 1 1 1 1 1 1 1 * ● 2BYTE CMD
RST
Note: VCO × 2 SET command should be issued in case of low voltage power supply application.
No. 5480-26/29
LC78622E
26. Sample Application Circuit
No. 5480-27/29
●
✕
✕
✕
●
✕
2
✕
✕
✕
✕
Digital output
Interpolation
Zero-cross
muting
Level meter
peak search
Bilingual
Digital attenuator
✕
✕
✕
—
✕
✕
✕
8fs
Digital
de-emphasis
1 bit D/A converter
Lowpass filter
—
—
●
—
2fs
Digital
filters
4fs
●
4
2✕/4✕
st
Speed
External
✕
✕
✕
—
—
—
✕
✕
✕
●
4
●
2✕
●
LC78681E →
LC78681KE
●
✕
✕
●
✕
✕
●
✕
✕
✕
—
●
—
—
—
—
—
✕
●
●
●
4
●
2✕/4✕
●
✕
●
●
●
4
●
st
●
When paired with When paired with
an analog ASP
an analog ASP
LC7869E
—
✕
●
●
●
4
●
st/4✕
●
LC7868E →
LC7868KE
●
LC7867E
16 KRAM
LC7861NE→
LC7861KE
When paired with
an analog ASP
LC7860KA
When paired with When paired with When paired with
an analog ASP
an analog ASP
an analog ASP
Product
EFM-PLL
Function
27. CD-DSP Functional Comparison
✕
●
●
●
—
—
●
●
●
●
4
●
2✕
●
Built-in VCO
LC78620E
●
●
●
—
●
—
●
●
✕
●
2
●
2✕
●
Built-in VCO
LC78622E
LC78622E
No. 5480-28/29
LC78622E
■ No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace
equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of
which may directly or indirectly cause injury, death or property loss.
■ Anyone purchasing any products described or contained herein for an above-mentioned use shall:
➀ Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and
distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all
damages, cost and expenses associated with such use:
➁ Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on
SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees
jointly or severally.
■ Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for
volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied
regarding its use or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of December, 1997. Specifications and information herein are subject to
change without notice.
No. 5480-29/29