SANYO LA9241M

Ordering number: EN 5564
Monolithic Linear IC
LA9241M
Analog Signal Processor (ASP)
for CD players
Package Dimensions
Overview
The LA9241M is an analog signal processing and servo control
bipolar IC designed for use in compact disc players; a compact
disc player can be configured by combining this IC with a
CD-DSP such as the LC78622E and LC78620E, with a small
number of additional components required.
unit : mm
3159-QFP64E
[LA9241M]
Functions
I/V amplifier, RF amplifier (with AGC), SLC, APC, FE, TE
(with VCA and auto-balance function), focus servo amplifier
(with offset cancellation function), tracking servo amplifier
(with offset cancellation function), spindle servo amplifier
(with gain switching function), sled servo amplifier (with off
function), focus detection (DRF, FZD), track detection (HFL,
TES), defect detection, and shock detection.
Features
SANYO : QFP64E
. The following automatic adjustment functions are built in.
. Focus offset auto cancel: FE (pin 20)
. Tracking offset auto cancel: TE (pin 7)
. EF balance auto adjustment
. RF level AGC function
. Tracking servo gain RF level following function
. Focus search smoothing setting pin: FSC (pin 46)
. EF balance adjustment variable range setting pin: (pin 47)
. Focus search mode switching pin: (pin 55)
Specifications
Maximum Ratings at Ta = 25°C, Pins 22, 45 = GND
Parameter
Maximum supply voltage
Allowable power dissipation
Symbol
VCC max
Pd max
Conditions
Pin 56, 64
Ratings
Unit
7
350
V
mW
Operating temperature
Topr
–25 to +75
°C
Storage temperature
Tstg
–40 to +150
°C
SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN
13097HA(II)/83096HA(II) No.5564 - 1/21
LA9241M
Operating Conditions at Pins 22, 45 = GND
Parameter
Symbol
Recommended supply voltage
Conditions
Ratings
VCC
Allowable operating supply voltage
VCC op
Unit
5
V
3.2 to 5.5
V
* Operating Supply Voltage at Limit of Operating Temperature at Pins 22, 45 = GND
Parameter
Symbol
Ratings
Unit
Topr2
–10 to +75
°C
VCC op2
3.0 to 5.5
V
Operating temperature
Allowable operating supply voltage
Conditions
Operating Characteristics at Ta = 25°C, Pins 22, 45 = GND, VCC (pins 56, 64) = 5 V
Parameter
Current drain
Reference voltage
[Interface]
CE-Vth
CL-Vth
DAT-Vth
Maximum CL frequency
[RF amplifier]
RFSM no signal voltage
Minimum gain
[Focus amplifier]
FDO gain
FDO offset
Off time offset
Offset adjustment step
F search voltage H1
F search voltage L1
F search voltage H2
F search voltage L2
[Tracking amplifier]
TE gain MAX
TE gain MIN
TE−3 dB
TO gain
TGL offset
TGH offset
THLD offset
Off 1 offset
Off 2 offset
Offset adjustment step
Balance range H
Balance range L
TOFF-VTH
TGL-VTH
[PH]
No signal voltage
[BH]
No signal voltage
[DRF]
Detection voltage
Output voltage H
Output voltage L
Symbol
ICCO
VREF
Conditions
VCC1 (pin 64) + VCC2 (pin 56)
VR
CEvth
CLvth
DATvth
CLmax
CE
CL
DAT
typ
32
2.5
max
42
2.7
0.8
0.8
0.8
FIN1, FIN2 : 1 MΩ-input, PH1 = 4 V
freq = 200 kHz, RFSM
Unit
mA
V
V
V
V
kHz
500
RFSMo
RFSMGmin
min
22
2.3
1.35
1.60
1.85
V
–14.0
–12.5
–11.0
dB
FDG
FDost
FDofost
FEstep
FSmax1
FSmin1
FSmax2
FSmin2
FIN2 : 1 MΩ-input, FDO
Difference from reference voltage, servo on
Difference from reference voltage, servo off
FE
FDO, FSS = GND
FDO, FSS = GND
FDO, FSS = VCC
FDO, FSS = VCC
3.5
–170
–40
5.0
0
0
3
0.8
–0.8
0.8
0
6.5
+170
+40
dB
mV
mV
mV
V
V
V
V
TEGmax
TEGmin
TEfc
TOG
TGLost
TGHost
THLDost
OFF1ost
OFF2ost
TEstep
BAL-H
BAL-L
TOFFvth
TGLvth
f = 10 kHz, E: 1 MΩ-input, PH1 = 4 V
f = 10 kHz, E: 1 MΩ-input, PH1 = 1 V
E: 1 MΩ-input
TH → TO gain, THLD mode
Servo on, TGL = H, TO
TGL = L, difference from TGL offset, TO
THLD mode, difference from TGL offset, TO
TOFF = H
TOFF2 off (IF)
TE
∆ Gain E/F input, TB = 5 V, TBC = open
∆ Gain E/F input, TB = 0 V, TBC = open
6.0
–0.5
9.0
+4.0
1.0
1.0
7.5
+1.8
60
6.0
0
0
0
0
0
30
3.5
–3.5
2.5
2.5
dB
dB
kHz
dB
mV
mV
mV
mV
mV
mV
dB
dB
V
V
4.0
–250
–50
–50
–50
–50
8.0
+250
+50
+50
+50
+50
3.0
3.0
PHo
Difference from RFSM
–0.85
–0.65
–0.45
V
BHo
Difference from RFSM
0.45
0.65
0.85
V
–0.60
4.5
–0.35
4.9
0
–0.20
V
V
V
DRFvth
DRF-H
DRF-L
Difference from VR at RFSM
+0.5
Continued on next page.
No.5564 - 2/21
LA9241M
Continued from preceding page.
Parameter
[FZD]
Detection voltage 1
Detection voltage 2
[HFL]
Detection voltage
Output voltage H
Output voltage L
[TES]
Detection voltage LH
Detection voltage HL
Output voltage H
Output voltage L
[JP]
Symbol
FZD1
FZD2
Unit
–0.4
4.9
0
–0.25
–0.10
0.10
4.9
0
–0.05
0.15
+0.5
V
V
V
V
0.35
0.5
0.65
V
–0.65
–0.5
–0.35
V
–40
–40
–30
0
0
0
+40
+40
+30
mV
mV
mV
0.75
1.0
1.25
V
–1.25
–1.0
–0.75
V
0.35
0.5
0.65
V
Difference from TO at SLEQ
SLEQ = VR, Difference from VR
Off mode
SLOF
–30
–100
–40
1.0
0
0
0
1.4
+30
+100
+40
2.0
mV
mV
mV
V
SLC
2.25
2.5
2.75
V
SCIo
SCIvthH
SCIvthL
SCI, difference from VR
SCI, difference from VR
SCI, difference from VR
–40
60
–140
0
100
–100
+40
140
–60
mV
mV
mV
DEFvth
Difference between LF2 voltage when RFSM =
3.5 V and DEF is detected and LF2 voltage when
RFSM = 3.5 V
0.20
0.35
0.50
V
4.5
4.9
0
+0.5
V
V
190
4.3
220
4.6
mV
V
Difference from VR at RFSM
TES-LH
TES-HL
TES-H
TES-L
TESI, difference from VR
TESI, difference from VR
JP-L
SPD12ost
SPD8ost
SPDof
Output voltage H12
SPD-H12
Output voltage L12
SPD-L12
Output voltage H8
SPD-H8
Output voltage H
Output voltage L
[APC]
Reference voltage
Off voltage
max
–0.55
4.5
HFLvth
HFL-H
HFL-L
Output voltage L
Detection voltage
typ
+0.2
0
JP-H
[Sled amplifier]
SLEQ offset
Offset SLD
Offset off
Off VTH
[SLC]
No signal voltage
[Shock]
No signal voltage
Detection voltage H
Detection voltage L
[DEF]
FE, difference from VR
FE, difference from VR
min
0
Output voltage H
[Spindle amplifier]
Offset 12
Offset 8
Offset off
Conditions
SLEQost
SLDost
SLDof
SLOFvth
SLCo
Difference from JP+ = 0 V, JP– = 0 V at JP+ = 0 V,
JP– = 5 V, TO
Difference from JP+ = 0 V, JP– = 0 V at JP+ = 5 V,
JP– = 0 V, TO
Difference from VR at SPD, 12 cm mode
Difference from VR at SPD, 8 cm mode
Difference from VR at SPD, OFF mode
Difference from offset-12, 12 cm mode
CV+ = 5 V, CV– = 0 V
Difference from offset-12 , 12 cm mode
CV+ = 0 V, CV– = 5 V
Difference from offset-8, 8 cm mode
CV+ = 5 V, CV– = 0 V
DEF-H
DEF-L
LDS
LDDof
LDS voltage at which LDD = 3 V
LDD
–0.15
0.05
4.5
160
3.9
V
V
+0.5
V
V
V
No.5564 - 3/21
LA9241M
Pin Functions
Pin
No.
1
FIN2
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
FIN1
E
F
TB
TE−
TE
TESI
SCI
TH
TA
TD−
TD
JP
TO
FD
FD−
FA
FA−
FE
FE−
AGND
NC
SP
SPG
SP−
SPD
SLEQ
SLD
SL−
SL+
JP−
JP+
TGL
TOFF
TES
HFL
38
39
40
41
42
43
44
45
46
47
48
49
50
51
SLOF
CV−
CV+
RFSM
RFS−
SLC
SLI
DGND
FSC
TBC
NC
DEF
CLK
CL
Symbol
Contents
Pickup photodiode connection pin. Added to FIN1 pin to generate the RF signal, subtracted from FIN1 pin to generate
the FE signal.
Pickup photodiode connection pin.
Pickup photodiode connection pin. Subtracted from F pin to generate the TE signal.
Pickup photodiode connection pin.
TE signal DC component input pin.
Pin which connects the TE signal gain setting resistor between this pin and TE pin.
TE signal output pin.
TES (Track Error Sense) comparator input pin. The TE signal is input through a bandpass filter.
Shock detection input pin.
Tracking gain time constant setting pin.
TA amplifier output pin.
Pin for configuring the tracking phase compensation constant between the TD and VR pins.
Tracking phase compensation setting pin.
Tracking jump signal (kick pulse) amplitude setting pin.
Tracking control signal output pin.
Focusing control signal output pin.
Pin for configuring the focusing phase compensation constant between the FD and FA pins.
Pin for configuring the focusing phase compensation constant between the FD− and FA− pins.
Pin for configuring the focusing phase compensation constant between the FA and FE pins.
FE signal output pin.
Pin which connects the FE signal gain setting resistor between this pin and FE pin.
Analog signal GND.
No connection
CV+ and CV− pins input signal single-end output.
12-cm spindle mode gain setting resistor connection pin.
Spindle phase compensation constant connection pin, along with the SPD pin.
Spindle control signal output pin.
Sled phase compensation constant connection pin.
Sled control signal output pin.
Input pin for sled movement signal from microprocessor.
Input pin for sled movement signal from microprocessor.
Input pin for tracking jump signal from DSP.
Input pin for tracking jump signal from DSP.
Input pin for tracking gain control signal from DSP. Gain is low when TGL is high.
Input pin for tracking off control signal from DSP. Tracking servo is off when TOFF is high.
Output pin for TES signal to DSP.
The High Frequency Level is used to determine whether the main beam is positioned over a bit or over the mirrored
surface.
Sled servo off control input pin
Input pin for CLV error signal from DSP.
Input pin for CLV error signal from DSP.
RF output pin.
RF gain setting and EFM signal 3T compensation constant setting pin, along with the RFSM pin.
Slice Level Control is an output pin that controls the data slice level used by the DSP for the RF waveform.
Input pin used by DSP for controlling the data slice level.
Digital system GND pin.
Focus search smoothing capacitor output pin.
Tracking Balance Control; EF balance adjustment variable range setting pin
No connection
Disc defect detection output pin.
Reference clock input pin. 4.23 MHz signal from the DSP is input.
Microprocessor command clock input pin.
Continued on next page.
No.5564 - 4/21
LA9241M
Continued from preceding page.
Pin
No.
52
53
54
55
56
57
58
59
60
61
62
63
64
Symbol
DAT
CE
DRF
FSS
VCC2
REFI
VR
LF2
PH1
BH1
LDD
LDS
VCC1
Contents
Microprocessor command data input pin.
Microprocessor command chip enable input pin.
RF level detection output (Detect RF).
Focus Search Select; focus search mode (± search/+search vs. the reference voltage) switching pin
Servo system and digital system VCC pin.
By-pass capacitor connection pin for reference voltage.
Reference voltage output pin.
Disc defect detection time constant setting pin.
RF signal peak hold capacitor connection pin.
RF signal bottom hold capacitor connection pin.
APC circuit output pin.
APC circuit input pin.
RF system VCC pin.
No.5564 - 5/21
LA9241M
Equivalent Circuit Block Diagram
Microcontroller
INTERFACE
No.5564 - 6/21
LA9241M
Test Circuit
No.5564 - 7/21
LA9241M
Description of Operation
1.
APC (auto laser power control)
This circuit controls the pickup laser power. The laser is turned on and off by commands from the microprocessor.
2.
RF amplifier (eye pattern output)
The pickup photodiode output current (A + C) is input to FIN2 (pin 1), and (B + D) is input to FIN1 (pin 2). The current that
is input is converted to the voltage, passes through the AGC circuit, and is then output from the RFSM amplifier output
RFSM (pin 41). The internal AGC circuit has a variable range of ±3 dB, and the time constant can be changed through the
external capacitor connected to PH1 (pin 60). In addition, this circuit also controls the bottom level of the EFM signal
(RFSM output), and the response can be changed through the external capacitor connected to BH1 (pin 61). The center gain
setting for the AGC variable range is set by the resistance between RFSM (pin 41) and RFS− (pin 42); if necessary, this
resistance is also used for 3T compensation for the EFM signal.
3.
SLC (slice level control)
The SLC sets the duty ratio for the EFM signal that is input to the DSP to 50%. The DC level is determined by integrating
the EFMO signal output from the DSP to determine the duty factor.
4.
Focus servo
The focus error signal is derived by detecting the difference between (A + C) and (B + D), which is (B + D) − (A + C), and
is then output from FE (pin 20). The focus error signal gain is set by the resistance between FE (pin 20) and FE− (pin 21).
Offset cancellation is performed by the FE amplifier. ‘‘Offset cancellation’’ cancels the offset for the IC’s internal IV
amplifier, etc. Adjustment is initiated by the FOCUS-OFFSET ADJUST START command, and terminates after about 30 ms.
The FOCUS-OFFSET ADJUST OFF command is used to return to the state before offset cancellation.
The FA amplifier is the pickup phase compensation amplifier, and the equalizer curve is set by the external capacitor and
resistance. Furthermore, this amplifier has a mute function which is applied when VCC is turned on, when the F-SERVO OFF
command is sent, and during F-SEARCH. In order to turn the focus servo on, send either the LASER ON command or the
F-SERVO ON command.
The FD amplifier has a phase compensation circuit, and a focus search signal composition function and is completed in about
560 ms. Focus search is initiated by the F-SEARCH command, and a ramp waveform is generated by the internal clock. This
waveform is used for focus detection (focus zero cross) with the focus error signal and then turn the focus servo on. The
ramp waveform amplitude is set by the resistance between FD (pin 16) and FD− (pin 17).
FSC (pin 46) is for smoothing the focus search ramp waveforms, and a capacitor is connected between FSC and REF.
FSS (pin 55) is the focus search mode switching pin. If FSS is shorted with VCC, the ‘‘+ search’’ is set; if FSS is left open or
is shorted with GND, the ‘‘± search’’ is set.
5.
Tracking servo
The pickup photodiode output current is input to E (pin 3) and F (pin 4). The current that is input is converted to the voltage,
passes through the balance adjustment VCA circuit and then the VCA circuit that follows the gain in the RFAGC circuit, and
is then output from TE (pin 7). The tracking error gain is set by the resistance between TE− (pin6) and TE (pin7).
Offset cancellation is performed by the TE amplifier. Offset cancellation terminates after about 30 ms. The TRACK-OFFSET
ADJUST OFF command is used to return to the state before the offset.
The TH amplifier alters the servo response characteristics according to the THLD signal, etc., generated internally after
detection of the TGL signal from the DSP or the JP signal. When a defect is detected, the THLD mode goes into effect
internally. To avoid this, short DEF (pin 49) to L = GND. By inserting an external bandpass filter to remove the shock
component from the tracking error signal at SCI (pin 9), the gain is automatically boosted when a defect is detected.
The TA output (pin 11) has a built-in resistance to allow configuration of a low-pass filter.
The TD amplifier performs servo loop phase compensation; the characteristics are set by external CR. Furthermore, this
amplifier has a mute function, which is applied when VCC is turned on or the TRACK-SERVO OFF command is issued. The
muting function is released by the TRACK-SERVO ON command.
The TOFF amplifier that is positioned immediately after TD (pin 13) functions to turn off the servo in response to the TOFF
signal from the DSP.
The TO amplifier has a JP pulse composition function. The JP pulse is set by JP (pin 14). (THLD detection is performed
internally.)
6.
Sled servo
The response characteristics are set by SLEQ (pin 28). The amplifier positioned after SLEQ (pin 28) has a mute function that
is applied either when SLOF (pin 38) goes high or the SLED OFF command is issued. The sled is moved by inputting
current to SL− (pin 30) and SL+ (pin 31); specifically, the pins are connected to the microprocessor output ports via resistors,
and the movement gain is set by the resistance value of that resistor. It is important to note that if there is a deviation in the
resistance values for SL− (pin 30) and SL+ (pin 31), an offset will arise in the SLD output.
7.
Spindle servo
This configures the servo circuit, which maintains the linear velocity of the disc at a constant speed, along with the DSP. This
circuit accepts signals from the DSP through CV− (pin 39) and CV+ (pin 40) and sets the equalizer characteristics through SP
(pin 24), SP− (pin 26), and SPD (pin 27), which are output to SPD (pin 27). The 12-cm mode amplifier gain is set by the
resistor connected between SPG (pin 25) and the reference voltage. In 8-cm mode, this amplifier serves as an internal buffer,
and SPG (pin 25) is ignored. Note that the gain setting is made for 8-cm mode first, and then 12-cm mode. If SPG (pin 25)
is left open, the gain is forcibly set for 8-cm mode, regardless of whether 8-cm or 12-cm mode is in effect.
No.5564 - 8/21
LA9241M
8.
TES and HFL (traverse signals)
When moving the pickup from the outer track to the inner track, the EF output from the pickup must be connected so that the
phase relationship of TES and HFL is as shown in the diagram below. For the TESI input, the TES comparator has negative
polarity and hysteresis of approximately ±100 mV. An external bandpass filter is needed in order to extract only the required
signal from the TE signal.
9.
DRF (luminous energy determination)
DRF goes high when the peak of the EFM signal (RFSM output) held by the PH1 (pin 60) capacitor exceeds approximately
2.1 V. The PH1 (pin 60) capacitor affects the DRF detection time constant and the RFAGC response bidirectional setting. The
DRF output is driven by a constant current (250 µA).
Pickup position
Focus
10. Focus determination
Focus is assumed to be obtained when the focus error signal S curve reaching REF + 0.2 V is detected, and the S curve
subsequently returns to REF.
Focus
No.5564 - 9/21
LA9241M
11. DEFECT
The mirrored surface level is maintained by the capacitor for LF2 (pin 59); when a drop in the EFM signal (RFSM output)
reaches 0.35 V or more, a high signal is output to DEF (pin 49). If DEF (pin 49) goes high, the tracking servo enters THLD
mode. In order to prevent the tracking servo from entering THLD mode when a defect is detected, prevent DEFECT from
being output by either shorting DEF (pin 49) to GND, or shorting LF2 (pin 59) to GND. The DEFECT output is driven by
constant current (approximately 100 µA).
EFM signal
(RFSM output)
LF2 (pin 59)
DEF (pin 49)
12. Microprocessor interface
Because the Reset (Nothing) command initializes the LA9241M, it must be used carefully.
The LA9241M command acceptance (mode switching) timing is defined by the internal clock (4.23 MHz divided to 130 kHz)
after the falling edge of CE (RWC); therefore, when commands are sent consecutively, CE must go low for at least 10 µsec.
The 4.23 MHz clock is required for that reason. 2BYTE-COMMAND DETECT and 2BYTE-COMMAND RESET are used
only for the purpose of masking two-byte data.
All instructions can be input by setting CE high and sending commands synchronized with the CL clock from the
microprocessor to DAT (pin 52) in LSB first format. Note that the command is executed at the falling edge of CE.
Timing
* The DSP pin names are shown in parentheses.
13. Reset circuit
The power-on reset is released when VCC exceeds approximately 2.6 V.
14. Pattern design notes
To prevent signal jump-in from CV+ (pin 40) to RFSM (pin 41), a shielding line is necessary in between.
15. VCC /REF/GND/NC
VCC1 (pin 64)
VCC2 (pin 56)
AGND (pin 22)
DGND (pin 45)
NC (pin 23, 48)
VR (Pin 58)
:
:
:
:
:
:
RF system
SERVO system, DIGITAL system
RF system, SERVO system
DIGITAL system
No connection
Reference voltage
No.5564 - 10/21
LA9241M
Microprocessor Command List
COMMAND
MSB
Reset mode
Power-on mode
LSB
DSP
00000000
RESET
RESET(NOTHING)
00001000
FOCUS START
FOCUS START #1
11110000
11111000
11111111
2BYTE-COMMAND DETECT
2BYTE-COMMAND DETECT
2BYTE-COMMAND RESET
2BYTE-COMMAND DETECT
2BYTE-COMMAND DETECT
2BYTE-COMMAND RESET
10010000
FOCUS-OFFSET ADJUST START
10010001
FOCUS-OFFSET ADJUST OFF
10010010
TRACK-OFFSET ADJUST START
10010011
TRACK-OFFSET ADJUST OFF
10010100
10010101
LASER ON
LASER OFF : F-SERVO ON
10010110
LASER OFF : F-SERVO OFF
10010111
SPINDLE 8CM
10011000
SPINDLE 12 CM
10011001
SPINDLE OFF
10011010
SLED ON
10011011
SLED OFF
TRACK-SERVO OFF
10011110
TRACK-SERVO ON
—
V
—
—
—
—
—
V
—
V
—
V
—
—
—
1 0 0 1 1 1 0 0 E/F BALANCE START
10011101
—
V
Non-adjusted
—
V
—
—
Notes Concerning Microprocessor Program Creation
1.
Commands
After sending the FOCUS START command and the E/F BALANCE START command, send 11111110 (FEH) in order to
clear the internal registers of the IC.
Reason: Although the above commands are executed at point 1 in the timing chart below, the same commands will be
executed again at point 2 if there is subsequent input to CE as shown below.
Timing
2 µs or more
2 µs or more
10 µs or more
1 µs or more
1 µs or more
‘‘FOCUS START’’ command
‘‘E/F BALANCE START’’ command
When sending a TRACK-OFFSET ADJUST START command or a FOCUS-OFFSET ADJUST START command after either
VCC ON (POWER ON RESET), RESET command, or a corresponding OFFSET ADJUST OFF command, waiting time is
necessary as listed below. (Only when a 4.2 MHz clock is input.)
TRACK-OFFSET ADJUST START: 4 ms or more
FOCUS-OFFSET ADJUST START: 4 ms or more
2.
E/F balance adjustment
E/F balance adjustments should be made in a bit region of the disc, not a mirrored region.
Since there is no track-kick for LA9241M, measures must be taken during EF balance adjustment to obtain a stable TE
signal. (By a sled movement signal from a microprocessor, for example.)
No.5564 - 11/21
LA9241M
Pin Internal Equivalent Circuit
Pin No.
Pin name
1
2
FIN2
FIN1
3
4
E
F
5
6
17
21
26
28
44
TB
TE–
FD−
FE−
SP−
SLEQ
SLI
16
27
43
FD
SPD
SLC
8
36
TESI
TES
Internal equivalent circuit
Continued on next page.
No.5564 - 12/21
LA9241M
Continued from preceding page.
Pin No.
Pin name
9
34
SCI
TGL
7
10
TE
TH
11
12
TA
TD−
13
TD
Internal equivalent circuit
Continued on next page.
No.5564 - 13/21
LA9241M
Continued from preceding page.
Pin No.
Pin name
14
JP
15
TO
18
19
20
FA
FA−
FE
Internal equivalent circuit
Continued on next page.
No.5564 - 14/21
LA9241M
Continued from preceding page.
Pin No.
Pin name
25
SPG
29
30
31
SLD
SL−
SL+
32
33
JP−
JP+
35
TOFF
Internal equivalent circuit
Continued on next page.
No.5564 - 15/21
LA9241M
Continued from preceding page.
Pin No.
Pin name
37
46
49
54
HFL
FSC
DEF
DRF
38
SLOF
39
40
24
CV−
CV+
SP
42
RFS−
47
TBC
Internal equivalent circuit
Continued on next page.
No.5564 - 16/21
LA9241M
ontinued from preceding page.
Pin No.
Pin name
50
CLK
51
52
53
CL
DAT
CE
55
FSS
57
58
REFI
VR
59
LF2
Internal equivalent circuit
Continued on next page.
No.5564 - 17/21
LA9241M
Continued from preceding page.
Pin No.
Pin name
41
60
61
RFSM
PH1
BH1
62
LDD
63
LDS
Internal equivalent circuit
No.5564 - 18/21
LA9241M
Sample Application Circuit
No.5564 - 19/21
.
.
.
.
Type
Package
Allowable operating supply voltage
VCCop max
VCCop min1
VCCop min2
Current drain (When VCC = 5 V)
VCO circuit built in
Auto adjustment function
Focus offset adjsutment
Maximum adjsutment time
Tracking offset adjustment
Maximum adjustment time
E/F balance auto adjustment
RF level AGC function
RF waveform amplitude when
VCC = 5 V
RF waveform amplitude when
VCC min
Tracking servo gain RF level
following function
Focus search time
Regeneration speed
Track-kick signal output
(Track-kick during E/F balance
adjsutment)
Focus search smoothing capacitor
pin: FSC
E/F balance variable range setting
pin: TBC
Focus search mode switch pin: FSS
Vth for HFL detection
DRF current capacity
APC reference voltage
LCD voltage where LDD = 3 V
No connection
LA9230M
QFP-64E
LA9231M
QFP-64E
LA9233M
QFP-64E
LA9240M
QFP-64E
5.5 V
3.2 V : t = –25 to +75°C
3.0 V : t = –10 to +75°C
32 mA
No
LA9241M
QFP-64E
No
2.3 V
Approx. 100 µA
180 mV: typ
Pin 47, 48, 55
No
No
No
2.3 V
Approx. 100 µA
180 mV: typ
Pin 46, 47, 48, 55
No
No
No
2.3 V
Approx.100 µA
180 mV: typ
No
Yes
Approx. 1.1 sec
×2
No output
Approx. 280 msec
×2
Built in
Approx. 280 msec
×2
Built in
Yes
1.3 Vp-p
Yes
1.3 Vp-p
Yes
1.3 Vp-p
Pin 47, 48, 55
No
2.3 V
Approx. 100 µA
180 mV: typ
No
Yes
Approx. 1.1 sec
×4
No output
Yes
1.3 Vp-p
Pin 48
Yes
2.1 V
Approx.250 µA
180 mV: typ
Yes
Yes
Approx. 560 msec
×4
No output
Yes
Pin 23,48
Yes
2.1 V
Approx. 250 µA
190 mV: typ
Yes
Yes
Approx. 560 msec
×4
No output
Yes
1.2 Vp-p : VCC = 3.4 V 0.9 Vp-p : VCC = 3.0 V
Adjustment position: FD Adjustment position: FD Adjustment position: FD Adjustment position: FD Adjustment position: FE Adjustment position: FE
270 ms
270 ms
270 ms
270 ms
30 ms
30 ms
Adjustment position: TO Adjustment position: TO Adjustment position: TO Adjustment position: TO Adjustment position: TE Adjustment position: TE
30 ms
30 ms
30 ms
30 ms
30 ms
30 ms
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
1.8 Vp-p
1.8 Vp-p
1.8 Vp-p
1.5 Vp-p
1.8 Vp-p
1.8 Vp-p
5.5 V
5.5 V
5.5 V
5.5 V
5.5 V
3.6 V : t = –25 to +75°C 3.6 V : t = –25 to +75°C 3.6 V : t = –25 to +75°C 3.6 V : t = –25 to +75°C 3.6 V : t = –25 to +75°C
3.4 V : t = –5 to +75°C
40 mA
32 mA
32 mA
32 mA
32 mA
Yes
No
No
No
No
LA9220M
QFP-64E
LA9241M
Function Comparisons for CD-ASP
No.5564 - 20/21
LA9241M
No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment,
nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or
indirectly cause injury, death or property loss.
Anyone purchasing any products described or contained herein for an above-mentioned use shall:
1 Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors
and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and
expenses associated with such use:
2 Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO
ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume
production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use
or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of January, 1997. Specifications and information herein are subject to change without notice.
No.5564 - 21/21