FAN3121 / FAN3122_F085 Single 9A High-Speed, Low-Side Gate Driver Features Description Qualified to AEC Q-100 The FAN3121 and FAN3122 MOSFET drivers are designed to drive N-channel enhancement MOSFETs in low-side switching applications by providing high peak current pulses. The drivers are available with either TTL (FAN312xT) or CMOS (FAN312xC) input thresholds. Internal circuitry provides an under-voltage lockout function by holding the output low until the supply voltage is within the operating range. Internal Resistors Turn Driver Off If No Inputs 4.5 to 18V Operating Range 11.4A Peak Sink at VDD = 12V 9.7A Sink / 7.1A Source at VOUT = 6V Inverting Configuration (FAN3121) and Non-Inverting Configuration (FAN3122) 23ns/19ns Typical Rise/Fall Times with 10nF Load 20ns Typical Propagation Delay Time Choice of TTL or CMOS Input Thresholds MillerDrive™ Technology FAN312x drivers incorporate the MillerDrive™ architecture for the final output stage. This bipolar / MOSFET combination provides the highest peak current during the Miller plateau stage of the MOSFET turn-on / turn-off process. The FAN3121 and FAN3122 drivers implement an enable function on pin 3 (EN), previously unused in the industry-standard pin-out. The pin is internally pulled up to VDD for active HIGH logic and can be left open for standard operation. 8-Lead SOIC Package Rated from –40°C to +125°C Applications Synchronous Rectifier Circuits High-Efficiency MOSFET Switching Switch-Mode Power Supplies DC-to-DC Converters Motor Control VDD 1 8 VDD VDD 1 8 VDD IN 2 7 OUT IN 2 7 OUT EN 3 6 OUT EN 3 6 OUT GND 4 5 GND GND 4 5 GND Figure 1. FAN3121 Pin Configuration © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 Figure 2. FAN3122 Pin Configuration www.fairchildsemi.com FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver February 2012 Part Number Logic Input Threshold Package Eco Status Packing Method Quantity per Reel FAN3121CMX_F085 Inverting Channels + FAN3121TMX_F085 Enable CMOS SOIC-8 RoHS Tape & Reel 2,500 TTL SOIC-8 RoHS Tape & Reel 2,500 FAN3122CMX_F085 Non-Inverting Channels + FAN3122TMX_F085 Enable CMOS SOIC-8 RoHS Tape & Reel 2,500 TTL SOIC-8 RoHS Tape & Reel 2,500 For Fairchild’s definition of “green” Eco Status, please visit: http://www.fairchildsemi.com/company/green/rohs_green.html. Package Outline Figure 3. SOIC-8 (Top View) Thermal Characteristics(1) Package JL(2) JT(3) JA(4) JB(5) JT(6) Units 38 29 87 41 2.3 °C/W 8-Pin Small Outline Integrated Circuit (SOIC) Notes: 1. Estimates derived from thermal simulation; actual values depend on the application. 2. Theta_JL (JL): Thermal resistance between the semiconductor junction and the bottom surface of all the leads (including any thermal pad) that are typically soldered to a PCB. 3. Theta_JT (JT): Thermal resistance between the semiconductor junction and the top surface of the package, assuming it is held at a uniform temperature by a top-side heatsink. 4. 5. 6. Theta_JA (ΘJA): Thermal resistance between junction and ambient, dependent on the PCB design, heat sinking, and airflow. The value given is for natural convection with no heatsink, as specified in JEDEC standards JESD51-2, JESD51-5, and JESD51-7, as appropriate. Psi_JB (JB): Thermal characterization parameter providing correlation between semiconductor junction temperature and an application circuit board reference point for the thermal environment defined in Note 4. For the SOIC-8 package, the board reference is defined as the PCB copper adjacent to pin 6. Psi_JT (JT): Thermal characterization parameter providing correlation between the semiconductor junction temperature and the center of the top of the package for the thermal environment defined in Note 4. © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 2 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Ordering Information Figure 4. 8 VDD VDD 1 8 VDD IN 2 7 OUT IN 2 7 OUT EN 3 6 OUT EN 3 6 OUT GND 4 5 GND GND 4 5 GND FAN3121 Pin Assignments (Repeated) Figure 5. FAN3122 Pin Assignments (Repeated) Pin Definitions FAN3121 FAN3122 Name Description 3 3 EN Enable Input. Pull pin LOW to inhibit driver. EN has logic thresholds for both TTL and CMOS IN thresholds. 4, 5 4, 5 GND 2 2 IN 6, 7 OUT Gate Drive Output. Held LOW unless required input is present and VDD is above the UVLO threshold. OUT Gate Drive Output (inverted from the input). Held LOW unless required input is present and VDD is above the UVLO threshold. VDD Supply Voltage. Provides power to the IC. 6, 7 1, 8 1, 8 Ground. Common ground reference for input and output circuits. Input. Output Logic FAN3121 FAN3122 EN IN 0 0 0 0 0 (7) 0 0 1 1 1(7) 0 1(7) (7) 1 1(7) 1 OUT EN IN OUT (7) 0 0 1 0 (7) (7) 0 1 1 0 0 Note: 7. Default input signal if no external connection is made. © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 3 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver VDD 1 VDD 1 8 100k Inverting (FAN3121) UVLO VDD_OK IN VDD OUT (FAN3121) 7 OUT (FAN3122) 2 100k 6 Non-Inverting 100k (FAN3122) OUT (FAN3121) OUT (FAN3122) VDD 100k EN 3 5 GND GND 4 Figure 6. © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 Block Diagram www.fairchildsemi.com 4 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Block Diagram Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. Max. Unit -0.3 20.0 V VDD VDD to GND VEN EN to GND GND - 0.3 VDD + 0.3 V VIN IN to GND GND - 0.3 VDD + 0.3 V OUT to GND GND - 0.3 VDD + 0.3 V VOUT TL Lead Soldering Temperature (10 Seconds) TJ Junction Temperature TSTG Storage Temperature ESD Human Body Model, JEDEC JESD22-A114 +260 ºC -55 +150 ºC -65 +150 ºC 2 kV Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol Parameter Min. Max. Unit 4.5 18.0 V VDD Supply Voltage Range VEN Enable Voltage EN 0 VDD V VIN Input Voltage IN 0 VDD V TA Operating Ambient Temperature -40 +125 ºC © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 5 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Absolute Maximum Ratings Unless otherwise noted, VDD=12V and TJ=-40°C to +125°C. Currents are defined as positive into the device and negative out of the device. Symbol Parameter Conditions Min. Typ. Max. Unit 18.0 V 0.65 0.90 0.58 0.85 Supply VDD Operating Range 4.5 TTL IDD Supply Current, Inputs / EN Not Connected VON Turn-On Voltage 3.5 4.0 4.3 V VOFF Turn-Off Voltage 3.25 3.75 4.15 V 0.8 1.0 (8) CMOS mA (9) Inputs (FAN312xT) VIL_T INx Logic Low Threshold VIH_T INx Logic High Threshold IINx_T Non-inverting Input Current IN = 0V -1.5 IINx_T Non-inverting Input Current IN = VDD 90 IINx_T Inverting Input Current IN = 0V -175.0 IINx_T Inverting Input Current IN = VDD -1.5 VHYS_T TTL Logic Hysteresis Voltage Inputs (FAN312xC) VIL_C 1.7 2.0 V 1.5 µA 120 175.0 µA -120 -90 µA 1.5 µA 0.85 V 0.40 0.70 30 38 (9) INx Logic Low Threshold VIH_C INx Logic High Threshold IINx_C Non-Inverting Input Current IN = 0V -1.5 IINx_C Non-Inverting Input Current IN = VDD 90 IINx_C Inverting Input Current IN = 0V -175 IINx_C Inverting Input Current IN = VDD -1.5 VHYS_C V 55 CMOS Logic Hysteresis Voltage %VDD 70 %VDD 1.5 µA 120 175 µA -120 -90 µA 1.5 µA 12 17 24 %VDD 1.2 1.6 2.0 V ENABLE (FAN3121, FAN3122) VENL Enable Logic Low Threshold EN from 5V to 0V VENH Enable Logic High Threshold EN from 0V to 5V VHYS_T TTL Logic Hysteresis Voltage RPU tD1, tD2 tD1, tD2 Enable Pull-up Resistance 1.8 2.2 2.6 V 0.2 0.6 0.8 V 68 100 134 kΩ (10) 8 17 27 ns (10) 14 21 33 ns Propagation Delay, EN Rising Propagation Delay, EN Falling Notes: 8. Lower supply current due to inactive TTL circuitry. 9. EN inputs have modified TTL thresholds; refer to the ENABLE section. 10. See Timing Diagrams of Figure 7 and Figure 8. © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 6 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Electrical Characteristics Unless otherwise noted, VDD=12V and TJ=-40°C to +125°C. Currents are defined as positive into the device and negative out of the device. OUTPUT ISINK OUT Current, Mid-Voltage, Sinking(11) OUT at VDD/2, CLOAD=1.0µF, f=1kHz 9.7 A ISOURCE OUT Current, Mid-Voltage, (11) Sourcing OUT at VDD/2, CLOAD=1.0µF, f=1kHz 7.1 A IPK_SINK OUT Current, Peak, Sinking CLOAD=1.0µF, f=1kHz 11.4 A CLOAD=1.0µF, f=1kHz 10.6 A (11) (11) IPK_SOURCE OUT Current, Peak, Sourcing VOH High Level Output Voltage VOH = VDD – VOUT, IOUT = –1mA 15 35 mV VOL Low Level Output Voltage IOUT = 1mA 10 25 mV tRISE tFALL (12) Output Rise Time (12) CLOAD=10nF 18 23 29 ns Output Fall Time CLOAD=10nF 11 19 27 ns tD1, tD2 Output Propagation Delay, CMOS (12) Inputs 0 – 12VIN, 1V/ns Slew Rate 9 18 28 ns tD1, tD2 Output Propagation Delay, TTL (12) Inputs 0 – 5VIN, 1V/ns Slew Rate 9 23 35 ns Notes: 11. Not tested in production. 12. See Timing Diagrams of Figure 7 and Figure 8. Timing Diagrams Figure 7. Non-Inverting © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 Figure 8. Inverting www.fairchildsemi.com 7 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Electrical Characteristics (Continued) Typical characteristics are provided at 25°C and VDD=12V unless otherwise noted. Figure 9. IDD (Static) vs. Supply Voltage(13) Figure 10. IDD (Static) vs. Supply Voltage(13) Figure 11. IDD (No-Load) vs. Frequency Figure 12. IDD (No-Load) vs. Frequency Figure 13. IDD (10nF Load) vs. Frequency Figure 14. IDD (10nF Load) vs. Frequency © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 8 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Typical Performance Characteristics Typical characteristics are provided at 25°C and VDD=12V unless otherwise noted. (13) (13) Figure 15. IDD (Static) vs. Temperature Figure 16. IDD (Static) vs. Temperature Figure 17. Input Thresholds vs. Supply Voltage Figure 18. Input Thresholds vs. Supply Voltage Figure 19. Input Thresholds % vs. Supply Voltage Figure 20. Enable Thresholds vs. Supply Voltage © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 9 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Typical Performance Characteristics Typical characteristics are provided at 25°C and VDD=12V unless otherwise noted. Figure 21. CMOS Input Thresholds vs. Temperature Figure 22. TTL Input Thresholds vs. Temperature Figure 23. Enable Thresholds vs. Temperature Figure 24. UVLO Thresholds vs. Temperature Figure 25. UVLO Hysteresis vs. Temperature Figure 26. Propagation Delay vs. Supply Voltage © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 10 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Typical Performance Characteristics Typical characteristics are provided at 25°C and VDD=12V unless otherwise noted. Figure 27. Propagation Delay vs. Supply Voltage Figure 28. Propagation Delay vs. Supply Voltage Figure 29. Propagation Delay vs. Supply Voltage Figure 30. Propagation Delay vs. Supply Voltage Figure 31. Propagation Delays vs. Temperature Figure 32. Propagation Delays vs. Temperature © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 11 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Typical Performance Characteristics Typical characteristics are provided at 25°C and VDD=12V unless otherwise noted. Figure 33. Propagation Delays vs. Temperature Figure 34. Propagation Delays vs. Temperature Figure 35. Propagation Delays vs. Temperature Figure 36. Fall Time vs. Supply Voltage Figure 37. Rise Time vs. Supply Voltage Figure 38. Rise and Fall Time vs. Temperature © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 12 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Typical Performance Characteristics Typical characteristics are provided at 25°C and VDD=12V unless otherwise noted. Figure 39. Rise / Fall Waveforms with 10nF Load (14) Figure 41. Quasi-Static Sink Current with VDD=12V (14) Figure 40. Quasi-Static Source Current with VDD=12V Figure 42. Quasi-Static Source Current with VDD=8V (14) V DD (2) x 4.7µF ceramic Current Probe LECROY AP015 FAN3121/22 IN 1kHz (14) Figure 43. Quasi-Static Sink Current with VDD=8V 470µF Al. El. IOUT 1µF ceramic VOUT C LOAD 1µF Figure 44. Quasi-Static IOUT / VOUT Test Circuit Notes: 13. For any inverting inputs pulled LOW, non-inverting inputs pulled HIGH, or outputs driven HIGH; static IDD increases by the current flowing through the corresponding pull-up/down resistor, shown in Figure 6. 14. The initial spike in each current waveform is a measurement artifact caused by the stray inductance of the current-measurement loop. © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 13 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Typical Performance Characteristics The FAN3121 and FAN3122 family offers versions in either TTL or CMOS input configuration. In the FAN3121T and FAN3122T, the input thresholds meet industry-standard TTL-logic thresholds independent of the VDD voltage, and there is a hysteresis voltage of approximately 0.7V. These levels permit the inputs to be driven from a range of input logic signal levels for which a voltage over 2V is considered logic HIGH. The driving signal for the TTL inputs should have fast rising and falling edges with a slew rate of 6V/µs or faster, so the rise time from 0 to 3.3V should be 550ns or less. The FAN3121 and FAN3122 output can be enabled or disabled using the EN pin with a very rapid response time. If EN is not externally connected, an internal pullup resistor enables the driver by default. The EN pin has logic thresholds for parts with either TTL or CMOS IN thresholds. In the FAN3121C and FAN3122C, the logic input thresholds are dependent on the VDD level and, with VDD of 12V, the logic rising edge threshold is approximately 55% of VDD and the input falling edge threshold is approximately 38% of VDD. The CMOS input configuration offers a hysteresis voltage of approximately 17% of VDD. The CMOS inputs can be used with relatively slow edges (approaching DC) if good decoupling and bypass techniques are incorporated in the system design to prevent noise from violating the input voltage hysteresis window. This allows setting precise timing intervals by fitting an R-C circuit between the controlling signal and the IN pin of the driver. The slow rising edge at the IN pin of the driver introduces a delay between the controlling signal and the OUT pin of the driver. Static Supply Current In the IDD (static) Typical Performance Characteristics, the curves are produced with all inputs / enables floating (OUT is LOW) and indicates the lowest static IDD current for the tested configuration. For other states, additional current flows through the 100k resistors on the inputs and outputs, as shown in the block diagram (see Figure 6). In these cases, the actual static IDD current is the value obtained from the curves, plus this additional current. MillerDrive™ Gate-Drive Technology FAN312x gate drivers incorporate the MillerDrive™ architecture shown in Figure 45. For the output stage, a combination of bipolar and MOS devices provide large currents over a wide range of supply voltage and temperature variations. The bipolar devices carry the bulk of the current as OUT swings between 1/3 to 2/3 VDD and the MOS devices pull the output to the HIGH or LOW rail. The purpose of the Miller Drive™ architecture is to speed up switching by providing high current during the Miller plateau region when the gate-drain capacitance of © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 the MOSFET is being charged or discharged as part of the turn-on / turn-off process. For applications with zero voltage switching during the MOSFET turn-on or turn-off interval, the driver supplies high peak current for fast switching, even though the Miller plateau is not present. This situation often occurs in synchronous rectifier applications because the body diode is generally conducting before the MOSFET is switched on. The output pin slew rate is determined by VDD voltage and the load on the output. It is not user adjustable, but a series resistor can be added if a slower rise or fall time at the MOSFET gate is needed. Figure 45. Miller Drive™ Output Architecture Under-Voltage Lockout (UVLO) The FAN312x startup logic is optimized to drive groundreferenced N-channel MOSFETs with an under-voltage lockout (UVLO) function to ensure that the IC starts in an orderly fashion. When VDD is rising, yet below the 4.0V operational level, this circuit holds the output low, regardless of the status of the input pins. After the part is active, the supply voltage must drop 0.25V before the part shuts down. This hysteresis helps prevent chatter when low VDD supply voltages have noise from the power switching. This configuration is not suitable for driving high-side P-channel MOSFETs because the low output voltage of the driver would turn the P-channel MOSFET on with VDD below 4.0V. VDD Bypassing and Layout Considerations The FAN3121 and FAN3122 are available in either 8-lead SOIC or MLP packages. In either package, the VDD pins 1 and 8 and the GND pins 4 and 5 should be connected together on the PCB. In typical FAN312x gate-driver applications, high-current pulses are needed to charge and discharge the gate of a power MOSFET in time intervals of 50ns or less. A bypass capacitor with low ESR and ESL should be connected directly between the VDD and GND pins to provide these large current pulses without causing unacceptable ripple on the VDD supply. To meet these requirements in a small size, a ceramic capacitor of 1µF www.fairchildsemi.com 14 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Applications Information Figure 46 shows the pulsed gate drive current path when the gate driver is supplying gate charge to turn the MOSFET on. The current is supplied from the local bypass capacitor CBYP and flows through the driver to the MOSFET gate and to ground. To reach the high peak currents possible with the FAN312x family, the resistance and inductance in the path should be minimized. The localized CBYP acts to contain the high peak current pulses within this driver-MOSFET circuit, preventing them from disturbing the sensitive analog circuitry in the PWM controller. VDD VDS The OUT pulses’ magnitude follows VDD magnitude with the output polarity inverted from the input until steadystate VDD is reached. VDD Turn-on threshold IN- IN+ (VDD) CBYP FAN3121/2 OUT PWM Figure 49. Inverting Startup Waveforms Figure 46. Current Path for MOSFET Turn-On Figure 477 shows the path the current takes when the gate driver turns the MOSFET off. Ideally, the driver shunts the current directly to the source of the MOSFET in a small circuit loop. For fast turn-off times, the resistance and inductance in this path should be minimized. VDD At power up, the FAN3122 non-inverting driver, shown in Figure 50, holds the output LOW until the VDD voltage reaches the UVLO turn-on threshold, as indicated in Figure 511. The OUT pulses magnitude follow VDD magnitude until steady-state VDD is reached. VDD VDS IN CBYP OUT FAN3121/2 Figure 50. Non-Inverting Driver PWM VDD Turn-on threshold Figure 47. Current Path for MOSFET Turn-Off Operational Waveforms At power up, the FAN3121 inverting driver shown in Figure 48 holds the output LOW until the VDD voltage reaches the UVLO turn-on threshold, as indicated in Figure 49. This facilitates proper startup control of lowside N-channel MOSFETs. IN- IN+ VDD IN OUT OUT Figure 48. Inverting Configuration Figure 51. Non-Inverting Startup Waveforms © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 15 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver or larger is typically used, with a dielectric material such as X7R, to limit the change in capacitance over the temperature and / or voltage application ranges. Gate drivers used to switch MOSFETs and IGBTs at high frequencies can dissipate significant amounts of power. It is important to determine the driver power dissipation and the resulting junction temperature in the application to ensure that the part is operating within acceptable temperature limits. In a full-bridge synchronous rectifier application, shown in Figure 522, each FAN3122 drives a parallel combination of two high-current MOSFETs, (such as FDMS8660S). The typical gate charge for each SR MOSFET is 70nC with VGS = VDD = 9V. At a switching frequency of 300kHz, the total power dissipation is: The total power dissipation in a gate driver is the sum of two components, PGATE and PDYNAMIC: PTOTAL = PGATE + PDYNAMIC (1) Gate Driving Loss: The most significant power loss results from supplying gate current (charge per unit time) to switch the load MOSFET on and off at the switching frequency. The power dissipation that results from driving a MOSFET at a specified gatesource voltage, VGS, with gate charge, QG, at switching frequency, fSW, is determined by: PGATE = QG • VGS • fSW (2) Dynamic Pre-drive / Shoot-through Current: A power loss resulting from internal current consumption under dynamic operating conditions, including pin pull-up / pull-down resistors, can be obtained using the “IDD (No-Load) vs. Frequency” graphs in Typical Performance Characteristics to determine the current IDYNAMIC drawn from VDD under actual operating conditions: PDYNAMIC = IDYNAMIC • VDD PGATE = 2 • 70nC • 9V • 300kHz = 0.378W (5) PDYNAMIC = 2mA • 9V = 18mW (6) PTOTAL = 0.396W (7) The SOIC-8 has a junction-to-board thermal characterization parameter of JB = 42°C/W. In a system application, the localized temperature around the device is a function of the layout and construction of the PCB along with airflow across the surfaces. To ensure reliable operation, the maximum junction temperature of the device must be prevented from exceeding the maximum rating of 150°C; with 80% derating, TJ would be limited to 120°C. Rearranging Equation 4 determines the board temperature required to maintain the junction temperature below 120°C: TB,MAX = TJ - PTOTAL • JB (8) TB,MAX = 120°C – 0.396W • 42°C/W = 104°C (9) . (3) Once the power dissipated in the driver is determined, the driver junction rise with respect to circuit board can be evaluated using the following thermal equation, assuming JB was determined for a similar thermal design (heat sinking and air flow): TJ = PTOTAL • JB + TB (4) where: TJ = driver junction temperature; JB = (psi) thermal characterization parameter relating temperature rise to total power dissipation; and TB = board temperature in location as defined in the Thermal Characteristics table. © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 16 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Thermal Guidelines V IN V OUT B2 A2 B1 A1 BIAS FAN3122 FAN3122 From A2 SR EN VDD 1 8 2 7 3 6 4 5 IN EN From A1 VDD OUT OUT 8 2 7 IN 3 SR EN EN 6 4 5 PGND AGND VDD 1 AGND VDD OUT OUT PGND Figure 52. Full-Bridge Synchronous Rectification VOUT VIN PWM FAN3121 VDD SR Enable Active HIGH IN EN AGND VBIAS 1 2 3 8 P1 (AGND) 4 7 6 5 VDD OUT OUT PGND Figure 53. Hybrid Synchronous Rectification in a Forward Converter © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 17 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Typical Application Diagrams Gate Input Drive(15) Threshold (Sink/Src) Part Number Type FAN3100C Single 2A +2.5A / -1.8A CMOS Single Channel of Two-Input/One-Output SOT23-5 FAN3100T Single 2A +2.5A / -1.8A TTL Single Channel of Two-Input/One-Output SOT23-5 FAN3226C Dual 2A +2.4A / -1.6A CMOS Dual Inverting Channels + Dual Enable SOIC8 FAN3226T Dual 2A +2.4A / -1.6A TTL Dual Inverting Channels + Dual Enable SOIC8 FAN3227C Dual 2A +2.4A / -1.6A CMOS Dual Non-Inverting Channels + Dual Enable SOIC8 FAN3227T Dual 2A +2.4A / -1.6A TTL Dual Non-Inverting Channels + Dual Enable SOIC8 FAN3228C Dual 2A +2.4A / -1.6A CMOS Dual Channels of Two-Input/One-Output, Pin Config.1 SOIC8 FAN3228T Dual 2A +2.4A / -1.6A TTL Dual Channels of Two-Input/One-Output, Pin Config.1 SOIC8 FAN3229C Dual 2A +2.4A / -1.6A CMOS Dual Channels of Two-Input/One-Output, Pin Config.2 SOIC8 FAN3229T Dual 2A +2.4A / -1.6A TTL Dual Channels of Two-Input/One-Output, Pin Config.2 SOIC8 FAN3223C Dual 4A +4.3A / -2.8A CMOS Dual Inverting Channels + Dual Enable SOIC8 FAN3223T Dual 4A +4.3A / -2.8A TTL Dual Inverting Channels + Dual Enable SOIC8 FAN3224C Dual 4A +4.3A / -2.8A CMOS Dual Non-Inverting Channels + Dual Enable SOIC8 FAN3224T Dual 4A +4.3A / -2.8A TTL Dual Non-Inverting Channels + Dual Enable SOIC8 FAN3225C Dual 4A +4.3A / -2.8A CMOS Dual Channels of Two-Input/One-Output SOIC8 FAN3225T Dual 4A +4.3A / -2.8A TTL Dual Channels of Two-Input/One-Output SOIC8 FAN3121C Single 9A +9.7A / -7.1A CMOS Single Inverting Channels + Enable SOIC8 FAN3121T Single 9A +9.7A / -7.1A TTL Single Inverting Channels + Enable SOIC8 FAN3122C Single 9A +9.7A / -7.1A CMOS Single Non-Inverting Channels + Enable SOIC8 FAN3122T Single 9A +9.7A / -7.1A TTL Single Non-Inverting Channels + Enable SOIC8 Logic Package Note: 15. Typical currents with OUT at 6V and VDD = 12V. © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 18 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Table 1. Related Products 5.00 4.80 A 0.65 3.81 8 5 B 6.20 5.80 PIN ONE INDICATOR 1.75 4.00 3.80 1 5.60 4 1.27 (0.33) 0.25 M 1.27 C B A LAND PATTERN RECOMMENDATION 0.25 0.10 SEE DETAIL A 1.75 MAX 0.25 0.19 C 0.51 0.33 0.50 x 45 0.25 R0.10 0.10 C OPTION A - BEVEL EDGE GAGE PLANE R0.10 OPTION B - NO BEVEL EDGE 0.36 NOTES: UNLESS OTHERWISE SPECIFIED 8ٛ 0ٛ 0.90 0.406 SEATING PLANE (1.04) DETAIL A SCALE: 2:1 A) THIS PACKAGE CONFORMS TO JEDEC MS-012, VARIATION AA, ISSUE C, B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS DO NOT INCLUDE MOLD FLASH OR BURRS. D) LANDPATTERN STANDARD: SOIC127P600X175-8M. E) DRAWING FILENAME: M08AREV13 Figure 54. 8-Lead SOIC Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 19 FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver Physical Dimensions (Continued) FAN3121 / FAN3122_F085 — Single 9A High-Speed, Low-Side Gate Driver © 2012 Fairchild Semiconductor Corporation FAN3121 / FAN3122_F085 • Rev. 1.0.0 www.fairchildsemi.com 20