M54HC157/158 M74HC157/158 HC157 QUAD 2 CHANNEL MULTIPLEXER HC158 QUAD 2 CHANNEL MULTIPLEXER (INV.) . . . . . . . . HIGH SPEED tPD = 10 ns (TYP.) AT VCC = 5 V LOW POWER DISSIPATION ICC = 4 µA (MAX.) AT TA = 25 °C HIGH NOISE IMMUNITY VNIH = VNIL = 28 % VCC (MIN.) OUTPUT DRIVE CAPABILITY 10 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE IOH = IOL = 4 mA (MIN.) BALANCED PROPAGATION DELAYS tPLH = tPHL WIDE OPERATING VOLTAGE RANGE VCC (OPR) = 2 V TO 6 V PIN AND FUNCTION COMPATIBLE WITH 54/74LS157/158 B1R (Plastic Package) F1R (Ceramic Package) M1R (Micro Package) C1R (Chip Carrier) ORDER CODES : M54HCXXXF1R M74HCXXXM1R M74HCXXXB1R M74HCXXXC1R PIN CONNECTIONS (top view) HC157 DESCRIPTION The M54/74HC157 and the M54/74HC158 are high speed CMOS QUAD 2-CHANNEL MULTIPLEXER’s fabricated with silicon gate C2MOS technology. They achieve the high speed operation similar to equivalent LSTTL while maintaining the CMOS low power dissipation. These devices consist of four 2-input digital multiplexers with common select and strobe inputs. The HC158 is an inverting multiplexer while the HC157 is a non-inverting multiplexer. When the STROBE input is held High, selection of data is inhibited and all the outputs become Low in the M74HC157 and High in the M74HC158. The SELECT decoding determines whether the A or B inputs get routed to their corresponding Y outputs. All inputs are equipped with protection circuits against static discharge and transient excess voltage. February 1993 HC158 NC = No Internal Connection 1/11 M54/M74HC157 M54/M74HC158 CHIP CARRIER HC157 HC158 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION (for HC157) PIN No 1 SYMBOL SELECT NAME AND FUNCTION Common Data Select Input 2, 5, 11, 14 1A to 4A 3, 6, 10, 13 PIN DESCRIPTION (for HC158) PIN No 1 SYMBOL SELECT NAME AND FUNCTION Common Data Select Input Data Inputs From Source A 2, 5, 11, 14 1A to 4A Data Inputs From Source A 1B to 4B Data Inputs From Source B 3, 6, 10, 13 1B to 4B Data Inputs From Source B 4, 7, 9, 12 15 1Y to 4Y STROBE Multiplexer Output Strobe Input 4, 7, 9, 12 15 1Y to 4Y STROBE Multiplexer Output Strobe Input 8 GND Ground (0V) 8 GND Ground (0V) 16 VCC Positive Supply Voltage 16 VCC Positive Supply Voltage 2/11 M54/M74HC157 M54/M74HC158 TRUTH TABLE INPUTS OUTPUTS STROBE H SELECT X A X B X Y (HC157) L Y (HC158) H L L L L L L H H X X L H X L H L L H L H X H H L X: DON’T CARE IEC LOGIC SYMBOL HC157 HC158 HC157 HC158 LOGIC DIAGRAM 3/11 M54/M74HC157 M54/M74HC158 ABSOLUTE MAXIMUM RATINGS Symbol Value Unit VCC VI Supply Voltage DC Input Voltage -0.5 to +7 -0.5 to VCC + 0.5 V V VO DC Output Voltage -0.5 to VCC + 0.5 V IIK IOK DC Input Diode Current DC Output Diode Current ± 20 ± 20 mA mA IO DC Output Source Sink Current Per Output Pin ± 25 mA DC VCC or Ground Current ± 50 mA 500 (*) mW ICC or IGND Parameter PD Power Dissipation Tstg TL Storage Temperature Lead Temperature (10 sec) -65 to +150 300 o o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied. (*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage VI Input Voltage VO Top Output Voltage Operating Temperature: M54HC Series M74HC Series Input Rise and Fall Time tr, tf 4/11 VCC = 2 V Value 2 to 6 Unit V 0 to VCC V 0 to VCC -55 to +125 -40 to +85 0 to 1000 V C o C ns VCC = 4.5 V 0 to 500 VCC = 6 V 0 to 400 o M54/M74HC157 M54/M74HC158 DC SPECIFICATIONS Test Conditions Symbol VIH V IL Parameter High Level Input Voltage Low Level Input Voltage Value VCC (V) TA = 25 oC 54HC and 74HC Min. Typ. Max. 2.0 1.5 1.5 1.5 4.5 6.0 3.15 4.2 3.15 4.2 3.15 4.2 High Level Output Voltage 0.5 0.5 0.5 4.5 1.35 1.35 1.35 2.0 4.5 6.0 4.5 VOL Low Level Output Voltage 6.0 2.0 4.5 6.0 4.5 6.0 II * ICC Input Leakage Current Quiescent Supply Current 6.0 6.0 1.8 1.8 Unit V 2.0 6.0 V OH -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. V 1.8 1.9 2.0 1.9 1.9 VI = IO=-20 µA VIH or V IL IO=-4.0 mA 4.4 5.9 4.5 6.0 4.4 5.9 4.4 5.9 4.18 4.31 4.13 4.10 IO=-5.2 mA 5.68 5.8 0.0 5.63 5.60 V VI = IO= 20 µA VIH or V IL IO= 4.0 mA 0.1 0.1 0.1 0.0 0.1 0.1 0.1 0.0 0.17 0.1 0.26 0.1 0.33 0.1 0.40 IO= 5.2 mA 0.18 V 0.26 0.33 0.40 VI = VCC or GND ±0.1 ±1 ±1 µA VI = VCC or GND IO =0 4 40 80 µA * Applicable only to DIR, G, G input 5/11 M54/M74HC157 M54/M74HC158 AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns) Test Conditions Symbol Parameter tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time (A, B - Y) tPLH tPHL Propagation Delay Time (SELECT - Y) tPLH tPHL Propagation Delay Time (STROBE - Y) Value o VCC (V) TA = 25 C 54HC and 74HC Min. Typ. Max. -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 2.0 30 75 95 110 4.5 6.0 8 7 15 13 19 16 22 19 2.0 30 100 125 150 4.5 12 20 25 30 6.0 10 17 21 26 Unit ns ns 2.0 50 125 155 190 4.5 6.0 16 14 25 21 31 26 38 32 2.0 36 115 145 175 4.5 6.0 12 10 23 20 29 25 35 30 ns 10 10 10 pF CIN Input Capacitance 5 CPD (*) Power Dissipation Capacitance 47 ns pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC/4 (per channel) SWITCHING CHARACTERISTICS TEST CIRCUIT TEST CIRCUIT ICC (Opr.) INPUT WAVEFORM IS THE SAME AS THAT IN CASE OF SWITCHING CHARACTERISTICS TEST. 6/11 M54/M74HC157 M54/M74HC158 Plastic DIP16 (0.25) MECHANICAL DATA mm DIM. MIN. a1 0.51 B 0.77 TYP. inch MAX. MIN. TYP. MAX. 0.020 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 F 7.1 0.280 I 5.1 0.201 L Z 3.3 0.130 1.27 0.050 P001C 7/11 M54/M74HC157 M54/M74HC158 Ceramic DIP16/1 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 20 0.787 B 7 0.276 D E 3.3 0.130 0.38 e3 0.015 17.78 0.700 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 H 1.17 1.52 0.046 0.060 L 0.22 0.31 0.009 0.012 M 0.51 1.27 0.020 0.050 N P Q 10.3 7.8 8.05 5.08 0.406 0.307 0.317 0.200 P053D 8/11 M54/M74HC157 M54/M74HC158 SO16 (Narrow) MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.004 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 9.8 E 5.8 10 0.385 6.2 0.228 0.393 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8° (max.) P013H 9/11 M54/M74HC157 M54/M74HC158 PLCC20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 9.78 10.03 0.385 0.395 B 8.89 9.04 0.350 0.356 D 4.2 4.57 0.165 0.180 d1 2.54 0.100 d2 0.56 0.022 E 7.37 8.38 0.290 0.330 e 1.27 0.050 e3 5.08 0.200 F 0.38 0.015 G 0.101 0.004 M 1.27 0.050 M1 1.14 0.045 P027A 10/11 M54/M74HC157 M54/M74HC158 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 11/11