New Product TPC6.8 thru TPC43A Vishay General Semiconductor Surface Mount PAR® Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions FEATURES ® • Junction passivation optimized design passivated anisotropic rectifier technology eSMP Series • TJ = 185 °C capability suitable for high reliability and automotive requirement A • Very low profile - typical height of 1.1 mm 1 • Ideal for automated placement • Uni-direction only 2 • Excellent clamping capability TO-277A (SMPC) • Low incremental surge resistance A Cathode 1 • Very fast response time Anode Cathode 2 • Meets MSL level 1, per J-STD-020 • AEC-Q101 qualified • Compliant to RoHS Directive 2002/95/EC and in accordance to WEEE 2002/96/EC PRIMARY CHARACTERISTICS • Halogen-free according to IEC 61249-2-21 definition VBR 6.8 V to 43 V PPPM 1500 W IFSM 200 A MECHANICAL DATA TJ max. 185 °C Case: TO-220AA (SMPC) Molding compound meets UL 94 V-0 flammability rating Base P/NHM3 - halogen-free, RoHS compliant, and automotive grade TYPICAL APPLICATIONS Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive, and telecommunication. Terminals: Matte tin plated leads, solderable J-STD-002 and JESD 22-B102 HM3 suffix meets JESD 201 class 2 whisker test per MAXIMUM RATINGS (TA = 25 °C, unless otherwise noted) PARAMETER Peak power dissipation with a 10/1000 μs waveform (fig. 3) SYMBOL VALUE UNIT (1)(2) PPPM 1500 W (1) IPPM See next table A IFSM 200 A VF 3.5 V TJ, TSTG - 65 to + 185 °C Peak power pulse current with a 10/1000 μs waveform (fig. 1) Peak forward surge current 8.3 ms single half sine-wave (2) Maximum instantaneous forward voltage at 100 A (3) Operating junction and storage temperature range Notes (1) Non-repetitive current pulse, per fig. 3 and derated above T = 25 °C per fig. 2 A (2) Measured on 8.3 ms single half sine-wave, or equivalent square wave, duty cycle = 4 pulses per minute maximum (3) Pulse test: 300 μs pulse width, 1 % duty cycle Document Number: 89056 Revision: 10-May-11 For technical questions within your region, please contact one of the following: www.vishay.com [email protected], [email protected], [email protected] 1 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product TPC6.8 thru TPC43A Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (TA = 25 °C, unless otherwise noted) TEST CURRENT IT (mA) STAND-OFF VOLTAGE VWM (V) MAXIMUM REVERSE LEAKAGE AT VWM IR (μA) MAXIMUM REVERSE LEAKAGE AT VWM TJ = 150 °C ID (μA) MAXIMUM PEAK PULSE SURGE CURRENT IPPM (2) (A) MAXIMUM CLAMPING VOLTAGE AT IPPM VC (V) DEVICE TYPE DEVICE MARKING CODE MIN. MAX. TPC6.8 DDP 6.12 7.48 10 5.50 1500 10 000 139 10.8 TPC6.8A DEP 6.45 7.14 10 5.80 1500 10 000 143 10.5 TPC7.5 DFP 6.75 8.25 10 6.05 500 5000 128 11.7 TPC7.5A DGP 7.13 7.88 10 6.40 500 5000 133 11.3 TPC8.2 DHP 7.38 9.02 10 6.63 200 2000 120 12.5 TPC8.2A DKP 7.79 8.61 10 7.02 200 2000 124 12.1 TPC9.1 DLP 8.19 10.0 1.0 7.37 50 500 109 13.8 TPC9.1A DMP 8.65 9.55 1.0 7.78 50 500 112 13.4 TPC10 DNP 9.0 11.0 1.0 8.10 20 200 100 15.0 TPC10A DPP 9.5 10.5 1.0 8.55 20 200 103 14.5 TPC11 DQP 9.9 12.1 1.0 8.92 5.0 50 92.6 16.2 TPC11A DRP 10.5 11.6 1.0 9.40 5.0 50 96.2 15.6 TPC12 DSP 10.8 13.2 1.0 9.72 2.0 10 86.7 17.3 BREAKDOWN VOLTAGE VBR (1) AT IT (V) TPC12A DTP 11.4 12.6 1.0 10.2 2.0 10 89.8 16.7 TPC13 DUP 11.7 14.3 1.0 10.5 2.0 10 78.9 19.0 TPC13A DVP 12.4 13.7 1.0 11.1 2.0 10 82.4 18.2 TPC15 DWP 13.5 16.5 1.0 12.1 1.0 10 68.2 22.0 TPC15A DXP 14.3 15.8 1.0 12.8 1.0 10 70.8 21.2 TPC16 DYP 14.4 17.6 1.0 12.9 1.0 10 63.8 23.5 TPC16A DZP 15.2 16.8 1.0 13.6 1.0 10 66.7 22.5 TPC18 EDP 16.2 19.8 1.0 14.5 1.0 10 56.6 26.5 TPC18A EEP 17.1 18.9 1.0 15.3 1.0 10 59.5 25.2 TPC20 EFP 18.0 22.0 1.0 16.2 1.0 10 51.5 29.1 TPC20A EGP 19.0 21.0 1.0 17.1 1.0 10 54.2 27.7 TPC22 EHP 19.8 24.2 1.0 17.8 1.0 10 47.0 31.9 TPC22A EKP 20.9 23.1 1.0 18.8 1.0 10 49.0 30.6 TPC24 ELP 21.6 26.4 1.0 19.4 1.0 10 43.2 34.7 TPC24A EMP 22.8 25.2 1.0 20.5 1.0 10 45.2 33.2 TPC27 ENP 24.3 29.7 1.0 21.8 1.0 10 38.4 39.1 TPC27A EPP 25.7 28.4 1.0 23.1 1.0 10 40.0 37.5 TPC30 EQP 27.0 33.0 1.0 24.3 1.0 10 34.5 43.5 TPC30A ERP 28.5 31.5 1.0 25.6 1.0 10 36.2 41.4 TPC33 ESP 29.7 36.3 1.0 26.8 1.0 10 31.4 47.7 TPC33A ETP 31.4 34.7 1.0 28.2 1.0 10 32.8 45.7 TPC36 EUP 32.4 39.6 1.0 29.1 1.0 15 28.8 52.0 TPC36A EVP 34.2 37.8 1.0 30.8 1.0 15 30.1 49.9 TPC39 EWP 35.1 42.9 1.0 31.6 1.0 15 26.6 56.4 TPC39A EXP 37.1 41.0 1.0 33.3 1.0 15 27.8 53.9 TPC43 EYP 38.7 47.3 1.0 34.8 1.0 20 24.2 61.9 TPC43A EZP 40.9 45.2 1.0 36.8 1.0 20 25.3 59.3 Notes (1) V BR measured after IT applied for 300 μs, IT = square wave pulse or equivalent (2) Surge current waveform per fig. 3 and derated per fig. 2 (3) All terms and symbols are consistent with ANSI/IEEE C62.35 www.vishay.com 2 For technical questions within your region, please contact one of the following: Document Number: 89056 [email protected], [email protected], [email protected] Revision: 10-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product TPC6.8 thru TPC43A Vishay General Semiconductor ORDERING INFORMATION (Example) PREFERRED P/N UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY DELIVERY MODE TPC10AHM3/86A (1) 0.10 86A 1500 7" diameter plastic tape and reel (1) 0.10 87A 6500 13" diameter plastic tape and reel TPC10AHM3/87A Note (1) Automotive grade RATINGS AND CHARACTERISTICS CURVES (TA = 25 °C unless otherwise noted) 150 TA = 25 °C Non-Repetitive Pulse Waveform shown in Fig. 3 10 1 TJ = 25 °C Pulse Width (td) is defined as the Point where the Peak Current decays to 50 % of IPPM tr = 10 µs Peak Value IPPM 100 Half Value - IPP IPPM 2 50 10/1000 µs Waveform as defined by R.E.A. td 0 1.0 µs 10 µs 100 µs 1.0 ms 10 ms 0 1.0 2.0 3.0 td - Pulse Width (s) t - Time (ms) Fig. 1 - Peak Pulse Power Rating Curve Fig. 3 - Pulse Waveform 100 4.0 10 000 VR, measured at Zero Bias Junction Capacitance (pF) Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage (%) 0.1 0.1 µs IPPM - Peak Pulse Current, % IRSM PPPM - Peak Power (kW) 100 75 50 25 0 1000 VR measured at Stand-Off Voltage, VWM 100 TJ = 25 °C f = 1.0 MHz Vsig = 50 mVp-p 10 0 50 100 150 200 1 10 TJ - Initial Temperature (°C) VBR - Breakdown Voltage (V) Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature Fig. 4 - Typical Junction Capacitance Document Number: 89056 Revision: 10-May-11 100 For technical questions within your region, please contact one of the following: www.vishay.com [email protected], [email protected], [email protected] 3 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product TPC6.8 thru TPC43A Vishay General Semiconductor PACKAGE OUTLINE DIMENSIONS in inches (millimeters) TO-277A (SMPC) 0.187 (4.75) 0.175 (4.45) 0.016 (0.40) 0.006 (0.15) A 0.262 (6.65) 0.250 (6.35) 0.242 (6.15) 0.238 (6.05) K 2 K 1 0.047 (1.20) 0.039 (1.00) 0.171 (4.35) 0.167 (4.25) 0.146 (3.70) 0.134 (3.40) Mounting Pad Layout 0.087 (2.20) 0.075 (1.90) 0.189 (4.80) MIN. 0.189 (4.80) 0.173 (4.40) 0.186 (4.72) MIN. 0.268 (6.80) 0.155 (3.94) NOM. 0.030 (0.75) NOM. 0.049 (1.24) 0.037 (0.94) 0.050 (1.27) MIN. 0.084 (2.13) NOM. 0.053 (1.35) 0.041 (1.05) 0.041 (1.04) 0.055 (1.40) MIN. Conform to JEDEC TO-277A www.vishay.com 4 For technical questions within your region, please contact one of the following: Document Number: 89056 [email protected], [email protected], [email protected] Revision: 10-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 11-Mar-11 www.vishay.com 1