TPSMC6.8 thru TPSMC47A Vishay General Semiconductor Surface Mount PAR® Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions FEATURES • Junction passivation optimized design passivated anisotropic rectifier technology • TJ = 185 °C capability suitable for high reliability and automotive requirement • Available in uni-directional polarity only • 1500 W peak pulse power capability with a 10/1000 µs waveform • Excellent clamping capability DO-214AB (SMC) • Very fast response time • Low incremental surge resistance • Meets MSL level 1, per J-STD-020, LF maximum peak of 260 °C PRIMARY CHARACTERISTICS VBR 6.8 V to 47 V PPPM 1500 W IFSM 200 A TJ max. 185 °C • AEC-Q101 qualified • Compliant to RoHS Directive 2002/95/EC and in accordance to WEEE 2002/96/EC TYPICAL APPLICATIONS Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive and telecommunication. MECHANICAL DATA Case: DO-214AB (SMC) Molding compound meets UL 94 V-0 flammability rating Base P/NHE3 - RoHS compliant, AEC-Q101 qualified Terminals: Matte tin plated leads, solderable per J-STD-002 and JESD 22-B102 HE3 suffix meets JESD 201 class 2 whisker test Polarity: Color band denotes cathode end MAXIMUM RATINGS (TA = 25 °C unless otherwise noted) PARAMETER Peak pulse power dissipation with a 10/1000 µs waveform (1)(2) (fig. 3) Peak power pulse current with a 10/1000 µs waveform (1) (fig. 1) Peak forward surge current 8.3 ms single half sine-wave (2)(3) Maximum instantaneous forward voltage at 100 A Operating junction and storage temperature range (2)(3) SYMBOL VALUE UNIT PPPM 1500 W IPPM See next table A IFSM 200 A VF 3.5 V TJ, TSTG - 65 to + 185 °C Notes (1) Non-repetitive current pulse, per fig. 3 and derated above TA = 25 °C per fig. 2 Mounted on 0.31" x 0.31" (8.0 mm x 8.0 mm) copper pads at each terminal (3) Measured on 8.3 ms single half sine-wave, or equivalent square wave, duty cycle = 4 pulses per minute maximum (2) Document Number: 88407 Revision: 09-Feb-11 For technical questions within your region, please contact one of the following: [email protected], [email protected], [email protected] www.vishay.com 1 TPSMC6.8 thru TPSMC47A Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted) DEVICE TYPE TPSMC6.8 TPSMC6.8A TPSMC7.5 TPSMC7.5A TPSMC8.2 TPSMC8.2A TPSMC9.1 TPSMC9.1A TPSMC10 TPSMC10A TPSMC11 TPSMC11A TPSMC12 TPSMC12A TPSMC13 TPSMC13A TPSMC15 TPSMC15A TPSMC16 TPSMC16A TPSMC18 TPSMC18A TPSMC20 TPSMC20A TPSMC22 TPSMC22A TPSMC24 TPSMC24A TPSMC27 TPSMC27A TPSMC30 TPSMC30A TPSMC33 TPSMC33A TPSMC36 TPSMC36A TPSMC39 TPSMC39A TPSMC43 TPSMC43A TPSMC47 TPSMC47A DEVICE MARKING CODE DDP DEP DFP DGP DHP DKP DLP DMP DNP DPP DQP DRP DSP DTP DUP DVP DWP DXP DYP DZP EDP EEP EFP EGP EHP EKP ELP EMP ENP EPP EQP ERP ESP ETP EUP EVP EWP EXP EYP EZP FDP FEP BREAKDOWN VOLTAGE VBR (1) AT IT (V) MIN. 6.12 6.45 6.75 7.13 7.38 7.79 8.19 8.65 9.00 9.50 9.90 10.5 10.8 11.4 11.7 12.4 13.5 14.3 14.4 15.2 16.2 17.1 18.0 19.0 19.8 20.9 21.6 22.8 24.3 25.7 27.0 28.5 29.7 31.4 32.4 34.2 35.1 37.1 38.7 40.9 42.3 44.7 MAX. 7.48 7.14 8.25 7.88 9.02 8.61 10.0 9.55 11.0 10.5 12.1 11.6 13.2 12.6 14.3 13.7 16.5 15.8 17.6 16.8 19.8 18.9 22.0 21.0 24.2 23.1 26.4 25.2 29.7 28.4 33.0 31.5 36.3 34.7 39.6 37.8 42.9 41.0 47.3 45.2 51.7 49.4 TEST CURRENT IT (mA) STAND-OFF VOLTAGE VWM (V) MAXIMUM REVERSE LEAKAGE AT VWM IR (µA) TJ = 150 °C MAXIMUM REVERSE LEAKAGE AT VWM ID (µA) 10.0 10.0 10.0 10.0 10.0 10.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 5.50 5.80 6.05 6.40 6.63 7.02 7.37 7.78 8.10 8.55 8.92 9.40 9.72 10.2 10.5 11.1 12.1 12.8 12.9 13.6 14.5 15.3 16.2 17.1 17.8 18.8 19.4 20.5 21.8 23.1 24.3 25.6 26.8 28.2 29.1 30.8 31.6 33.3 34.8 36.8 38.1 40.2 1000 1000 500 500 200 200 50 50 20 20 5.0 5.0 2.0 2.0 2.0 2.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 10000 10000 5000 5000 2000 2000 500 500 200 200 50 50 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 15 15 15 15 20 20 20 20 MAXIMUM PEAK PULSE SURGE CURRENT IPPM (2) (A) MAXIMUM CLAMPING VOLTAGE AT IPPM VC (V) 139.0 143.0 128.0 133.0 120.0 124.0 109.0 112.0 100.0 103.0 92.6 96.2 86.7 89.8 78.9 82.4 68.2 70.8 63.8 66.7 56.6 59.5 51.5 54.2 47.0 49.0 43.2 45.2 38.4 40.0 34.5 36.2 31.4 32.8 28.8 30.1 26.6 27.8 24.2 25.3 22.1 23.1 10.8 10.5 11.7 11.3 12.5 12.1 13.8 13.4 15.0 14.5 16.2 15.6 17.3 16.7 19.0 18.2 22.0 21.2 23.5 22.5 26.5 25.2 29.1 27.7 31.9 30.6 34.7 33.2 39.1 37.5 43.5 41.4 47.7 45.7 52.0 49.9 56.4 53.9 61.9 59.3 67.8 64.8 Notes (1) VBR measured after IT applied for 300 µs, IT = square wave pulse or equivalent Surge current waveform per fig. 3 and derated per fig. 2 (3) All terms and symbols are consistent with ANSI/IEEE C62.35 (2) www.vishay.com 2 For technical questions within your region, please contact one of the following: [email protected], [email protected], [email protected] Document Number: 88407 Revision: 09-Feb-11 TPSMC6.8 thru TPSMC47A Vishay General Semiconductor ORDERING INFORMATION (Example) PREFERRED P/N UNIT WEIGHT (g) PREFERRED PACKAGE CODE TPSMC6.8AHE3/57T (1) BASE QUANTITY DELIVERY MODE 0.211 57T 850 7" diameter plastic tape and reel TPSMC6.8AHE3/9AT (1) 0.211 9AT 3500 13" diameter plastic tape and reel Note (1) AEC-Q101 qualified RATINGS AND CHARACTERISTICS CURVES (TA = 25 C unless otherwise noted) 150 TA = 25 °C Non-Repetitive Pulse Waveform shown in Fig. 3 10 1.0 0.31 x 0.31" (8.0 x 8.0 mm) Copper Pad Areas TJ = 25 °C Pulse Width (td) is defined as the Point where the Peak Current decays to 50 % of IPPM tr = 10 µs Peak Value IPPM 100 Half Value - IPP IPPM 2 50 10/1000 µs Waveform as defined by R.E.A. td 0 1.0 µs 10 µs 100 µs 1.0 ms 10 ms 0 1.0 2.0 3.0 td - Pulse Width (s) t - Time (ms) Figure 1. Peak Pulse Power Rating Curve Figure 3. Pulse Waveform 4.0 10 000 100 VR, measured at Zero Bias Junction Capacitance (pF) Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage, % 0.1 0.1 µs IPPM - Peak Pulse Current, % IRSM PPPM - Peak Power (kW) 100 75 50 25 1000 VR measured at Stand-Off Voltage, VWM 100 TJ = 25 °C f = 1.0 MHz Vsig = 50 mVp-p 10 0 0 50 100 150 200 1 10 100 TJ - Initial Temperature (°C) VBR - Breakdown Voltage (V) Figure 2. Pulse Power or Current vs. Initial Junction Temperature Figure 4. Typical Junction Capacitance Document Number: 88407 Revision: 09-Feb-11 For technical questions within your region, please contact one of the following: [email protected], [email protected], [email protected] www.vishay.com 3 TPSMC6.8 thru TPSMC47A Vishay General Semiconductor Peak Forward Surge Current (A) 200 TJ = TJ max. 8.3 ms Single Half Sine-Wave 100 50 10 1 5 10 50 100 Number of Cycles at 60 Hz Figure 5. Maximum Non-Repetitive/Peak Forward Surge Current PACKAGE OUTLINE DIMENSIONS in inches (millimeters) DO-214AB (SMC) Cathode Band Mounting Pad Layout 0.185 (4.69) MAX. 0.246 (6.22) 0.220 (5.59) 0.126 (3.20) 0.114 (2.90) 0.126 (3.20) MIN. 0.280 (7.11) 0.260 (6.60) 0.060 (1.52) MIN. 0.012 (0.305) 0.006 (0.152) 0.320 (8.13) REF. 0.103 (2.62) 0.079 (2.06) 0.060 (1.52) 0.030 (0.76) 0.008 (0.2) 0 (0) 0.320 (8.13) 0.305 (7.75) www.vishay.com 4 For technical questions within your region, please contact one of the following: [email protected], [email protected], [email protected] Document Number: 88407 Revision: 09-Feb-11 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 11-Mar-11 www.vishay.com 1