U2102B Multifunction Timer Description The monolithic integrated bipolar circuit U2102B is an MOSFET or IGBT control circuit which allows realization of an extremely wide range of timer and dimmer functions. The integrated current monitoring function additionally permits the power switch to be reliably protected without an additional fuse. Features D Adjustable and retriggerable tracking time D External window adjustment for sensor input D Enable input for triggering D Integrated reverse phase control D Two- or three-wire applications D Mode selection: – Zero-voltage switch with static output – Two-stage reverse phase control with switch-off – Two-stage reverse phase control D Current monitoring: – High-speed short-circuit monitoring with output – High-current monitoring with integrating buffer D Integrated chip temperature monitoring Applications D D D D D Motion detectors Time-delay relays Dimmers Reverse phase controls Timers Package: DIP16, SO16 94 8666 1 16 Voltage monitoring VRef 2 3 4 5 Synchronization 15 Reverse phase control Voltage limitation Control RC oscillator 14 Push pull Divider logic 13 12 6 Current monitoring Programing Triggering with buffers 7 8 Temperature monitoring 11 Test logic 10 9 Figure 1. Block diagram TELEFUNKEN Semiconductors Rev. A1, 30-May-96 1 (16) 2 (16) Trigger signal 1 mF CRef R2 Enable + VS C2 220 nF 100kW 22 k W 1 MW 2 GND VRef Control R3 8 – + – + GND 0.1/0.4/ 0.5 x VRef 7 Stat. ZVS 0.45 x VRef – 0.2 x V9 Trigger window 0.55 x VRef + 0.2 V9 Enable Voltage monitoring Divider Control Phase Buffer (spikefilter) logic Control Clock generator Reverse Clock 1 kW Test mode 2 stage + VS 2 stage / out VRef RC oscillator – + Ramp VRef 0.02xVRef 6 5 4 820 k W 3 C3 10 nF 1 Push pull Clock Clock – Test logic – + + Window adjustment Buffer 120 ms Current monitoring POR Q Q R S Temp monitoring Voltage limitation Synchronization 9 10 100 mV 11 500 mV 12 GND 13 14 15 +Vs 16 C1 100 W RG 47 mF/25 V 68 k W R1 33 k W / 2 W NTC VRef 1 nF 1 kW Rsh IGBT Load Vmains 230 V X 94 8220 e U2102B Figure 2. Block diagram with typical circuit for dc loads TELEFUNKEN Semiconductors Rev. A1, 30-May-96 U2102B Pin Description Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Symbol VRef CRamp RRamp Control Osc Prog. EN Trigger V9 Test II Ioff GND VO + VS Sync Function Reference voltage 5 V Ramp, capacitance Current setting for ramp Control voltage RC oscillator Tri state programing Enable-input Trigger-input (window) Window-adjustment Test output Input current monitoring Fast output current monitoring Ground Output voltage Supply voltage Synchronization input TELEFUNKEN Semiconductors Rev. A1, 30-May-96 VRef 1 16 Sync CRamp 2 15 +VS RRamp 3 14 VO Control 4 13 GND Osc 5 12 Ioff Prog. 6 11 II EN 7 10 Test Trigger 8 9 V9 94 8619 3 (16) U2102B Power Supply, Synchronization Pins 15 and 16 The voltage limitation circuit contained in the U2102B enables simple power supply via a dropping resistor R1. In the case of dc loads, practically all the supply current flows into Pin 16 (the pull down resistor at Pin 16 is necessary in order to guarantee reliable synchronization) and is supplied via an internal diode to Pin 15, where the resultant supply voltage is limited and smoothed by C1. As a result, the rectified and divided line voltage appears at Pin 16, where the amplitude is limited. The power supply for the circuit can be realized in all modes for dc loads as shown in figure 3. The voltage at Pin 16 is used to synchronize the circuit with the mains and generate the system clock required for the buffers. The circuit detects a “zero crossing” when the voltage at Pin 16 falls below an internal threshold of approximately 8 V. Vmains R1=Rsync Sync. 16 +VS Load 15 Voltage limitation C1 Push pull 14 IGBT RG Temp. monit. Rsh GND 13 95 9882 Figure 3. Power supply for dc loads (R1 is identical with Rsync) R1 is calculated here as follows: V Nmin –V S R 1max 0.85 (1) I tot + where: VNmin = Vmains – 15% VS Supply voltage 4 (16) = Itot = ISmax + Ix ISmax = Max. current consumption of the IC Ix = Current consumption of the external components TELEFUNKEN Semiconductors Rev. A1, 30-May-96 U2102B In the case of ac loads, it is necessary to make a distinction for power supply purposes between the individual operating modes. In reverse phase control mode, figure 4, Pin 15 must be additionally supplied with power via a dropping resistor, since no current flows in Pin 16 when the power switch is switched on. Here, the dropping resistor, R1, is connected before the rectifier bridge and therefore has only one mains half-wave. R1 is then calculated as follows: R 1max + 0.85 @ V2 @ I–V Nmin Load Rsync Sync. S tot Vmains D1 16 R1 +VS Figure 4. Power supply in reverse phase control mode for ac loads 15 Voltage limitation C1 Push pull IGBT 14 RG Temp. monit. Rsh GND 13 95 9883 In two-wire systems, the additional power supply at Pin 15 is not possible (see figure 4, by omitting R1 and Diode D1). In this case, the resistor Rsync is identical with R1 and should be as low as the power dissipation allows it. A sufficiently large residual phase angle must remain in this case in order to guarantee the device supply. The power supply is simplified if the device is operated as a static zero-voltage switch for ac loads (see figure 5). All delay times are twice as long here, since synchronization of the module is tapped before the rectifier bridge. Load Vmains R1= Rsync Sync. 16 +VS Figure 5. Power supply as static zero voltage switch for ac loads 15 Voltage limitation C1 Push pull 14 Temp. monit. IGBT RG Rsh GND 13 95 9884 TELEFUNKEN Semiconductors Rev. A1, 30-May-96 5 (16) U2102B Voltage Monitoring Reverse Phase Control, Pins 2, 3, 4 While the operating voltage is being built up or reduced, uncontrolled conditions or output pulses of insufficient amplitude are being suppressed by the internal monitoring circuit. All latches in the circuit, the divider and the control logic are reset. When the supply voltage is applied, the enable threshold (clamp voltage) of approximately 16 V must be reached so that the circuit is enabled. The circuit is reset at approximately 11 V if the supply voltage breaks down. A further threshold is activated in reverse phase control mode. If the supply voltage breaks down here after enabling of the circuit, the output stage is switched off at approximately 12.5 V, while the other parts of the circuit are not affected. The output stage can then be switched on again only in the following halfwave. As a result, the residual phase angle remains just large enough, (e.g., in two-wire systems), so that the circuit can still be properly supplied with power. In all operating modes, a single operating cycle is started after the supply voltage is applied, independently of the trigger inputs, in order to immediately demonstrate the overall function. In the case of normal phase controls, e.g., with a triac, the load current is switched ON only at a certain phase angle after the zero crossing of the mains voltage. In the following zero crossing of the current, the triac gets extinguished (switched-off) automatically. Reverse phase control differs from this in that the load current is always switched-on by a semiconductor switch (e.g., IBGT) at the zero crossing of the mains voltage and then switched back off again after a certain phase angle a. This has the advantage that the load current always rises with the mains voltage in a defined manner and thus keeps the required interference suppression to a minimum. Chip Temperature Monitoring The circuit possesses an integrated chip temperature monitoring circuit which disables the output stage when a temperature of approximately 140°C is reached. The circuit is enabled again only after cooling down and additionally switched “off and on” of the operating voltage. The charging current for the capacitor C3 at Pin 2 is set with the resistor R3 at Pin 3. When the synchronization circuit recognizes a zero crossing, an increased charging 4 I3 is enabled which then charges C3 up current I2 to 0.45 V. The output stage is switched-on at this value and the charging current for C3 is reduced to I2 = I3. Since the actual zero crossing of the supply voltage occurs later than recognized by the circuit, the load current starts to flow quite close to the exact zero crossing of the supply voltage. While the output stage is switched-on C3 is charged until the control voltage, set externally at Pin 4, is reached. When this condition is reached, the output stage is switched off and C3 is charged again with the increased current (I2 = 4 I3) to V2 5.5 V. The charging current is switched off at this point and C3 is discharged internally. The whole process then starts again when the circuit recognizes another zero crossing (see figure 6). [ [ [ Vmains t V2 1.1 VRef V4 0.09 VRef t V14 t 94 8290 e Figure 6. Signal characteristics of reverse phase control 6 (16) TELEFUNKEN Semiconductors Rev. A1, 30-May-96 U2102B Programing, Pin 6 Three operating modes can be programed with the tristate input Pin 6: D Zero-voltage switch (ZVS)with static output (V6 = V1 = VRef): The reverse phase control is inactive here. The output stage is statically switched-on after triggering by the timer and switched-off again after the running down of the time (at the zero crossing of the supply voltage in each case). This operating mode is not possible in two–wire systems. D Two-stage reverse phase control with switch-off ( V6 = V15 = VS): The maximum current flow angle, amax, is set when the timer has enabled the output stage. Switchover to the phase angle a, which can be set arbitrarily at Pin 4, takes place after expiry of 3/4 of the tracking time set at Pin 5. The output stage switches off after expiry of the whole tracking time. D Two-stage reverse phase control ( V6 = V13 = GND): The output stage switches to the maximum current flow angle, amax, (adjustable) if the trigger condition for both inputs (Pins 7, 8) is satisfied. Switchover to the current flow angle, a, set at Pin 4 takes place after expiry of 3/4 of the tracking time set at Pin 5. The whole process is repeated from the beginning again if renewed triggering takes place at Pin 8. The lamp is switched-off in the following half-wave of the mains voltage if the trigger condition at Pin 7 disappears. In this mode, the output stage is switched-on even if only Pin 7 is in the ON state. The current flow angle is then determined by V4 (e.g., house no. illumination, twilight switch). This threshold is approximately 2 V in switched-off condition and also during the second current flow angle, aain two-stage reverse phase control mode. Otherwise, the blocking-or switch-off threshold is 0.5 V. The input Pin 8 is designed as a window discriminator, its window is set at Pin 9. The minimum window of approximately 250 mV is set with V9 = V13, and the maximum window of approximately 1.25 V with V9 = Vl. The window discriminator is in the OFF state when the voltage at Pin 8 lies within the window set at Pin 9. If a resistor divider with an NTC resistor is connected to Pin 9, for example, it is possible to compensate for the temperature dependence of the IR sensor, i.e. the range is made independent of temperature. Noise suppression for tON = 40 ms guarantees that there is no peak noise signals at the inputs which could trigger the circuit. Equally, renewed triggering is prevented for tOFF = 640 ms after load switch-off in order to avoid any self interference. V7 VRef ON 0.5 VRef Hysteresis 0.1/0.4 VRef OFF 0 94 8291 e Figure 7. Trigger condition Pin 7 Trigger Inputs, Pins 7 and 8 The trigger condition of the timer is determined by the two inputs Pins 7 and 8. A Light Dependent Resistor ( LDR) can be connected to Pin 7, for example, and an IR sensor to Pin 8. Both inputs must be in the ON state to initiate triggering, since they are equal and AND-gated. In the operating mode “2-stage reverse phase control”, the output stage can additionally be switched-on and switched-off by Pin 7 alone and independently of the timer. The enable input Pin 7 is implemented as a comparator with hysteresis. The enable threshold is approximately 2.5 V. The blocking threshold is switched by the control logic in order to avoid faults as a result of load switching. TELEFUNKEN Semiconductors Rev. A1, 30-May-96 V8 VRef ON 0.5 VRef 0.05 VRef + 0.2 V9 OFF 0.05 VRef + 0.2 V9 ON 0 94 8292 e Figure 8. Trigger condition Pin 8 7 (16) U2102B RC Oscillator, Pin 5 Current Monitoring, Pins 11 and 12 An internal RC oscillator with following divider stage 1:211 permits a very long and reproducible tracking time. The current monitoring circuit integrated in the U2102B represents a double electronic fuse. The circuit measures the current flowing through the power switch by way of the voltage drop across the shunt resistor Rsh. This voltage is supplied to Pin 11. If this voltage exceeds a value of 500 mV because of a high load current (e.g., shortcircuit), the switch-off latch is set and the switching output Pin 11 closes immediately. Pin 11 can be connected to the gate via a resistor or network, depending on load conditions, thus allowing the switch-off behavior to be adapted to the respective requirements. The shortcircuit current is reduced to a problem-free value by this procedure. The RC values for a certain tracking time, tt, are calculated as follows: R 2 (kW) + 1.4 t t(s) 10 3 2048 C 2 (mF) C 2 (mF) + 1.4 t t(s) 10 3 2048 R 2 (kW) In reverse phase control mode, switchover from maximum current flow angle to the value set at Pin 4 takes place after expiry of 3/4 of the total tracking time tt. 8 (16) There is a second threshold at 100 mV. The output stage is disabled if the voltage at Pin 11 exceeds this value and if it reaches this value for 120 ms in every half-wave without exceeding the switch-off threshold of 500 mV. Since high voltage peaks would be caused by switching off due to the line and leakage inductances, the output stage is not switched-off immediately but is simply not enabled in the next half-wave. The circuit is designed so that it also switches off in the case of changing overcurrents which do not occur in every half-wave. But in this case the switch-off time is larger. TELEFUNKEN Semiconductors Rev. A1, 30-May-96 U2102B Absolute Maximum Ratings Reference point Pin 13, unless otherwise specified Parameters Power supply Current Synchronization Input current t < 10 ms v t 10 ms Reference voltage source Output current Push-pull output stage Output current t 2 ms v Input currents Input voltages Symbol Value Unit Pin 15 IS is 20 60 mA Pin 16 II ii 20 60 mA Pin 1 – IRef 10 mA Pin 14 Pin 14 "I "i 10 60 mA Pin 2 Pin 2 Pin 3 Pin 10 Pin 12 Pins 4, 5, 7, 8, 9 and 11 Pins 6 and 12 Storage temperature range Junction temperature Ambient temperature O o –II II –II II II VI VI Tstg Tj Tamb 0 V to V1 0V to V15 – 40 to + 125 + 125 – 10 to + 100 °C °C °C Symbol Value Unit RthJA 120 180 100 K/W " 1 8 0.2 1 20 mA Thermal Resistance Parameters Junction ambient DIP 16 SO 16 on PC board SO 16 on ceramic TELEFUNKEN Semiconductors Rev. A1, 30-May-96 9 (16) U2102B Electrical Characteristics VS = 15.0 V, fmains = 50 Hz, Tamb = 25°C, reference point Pin 13, unless otherwise specified Parameters Supply voltage limitation Current consumption Voltage monitoring Switch-on threshold Switch-off threshold Undervoltage threshold Reference voltage Synchronization Voltage limitation Input current Zero crossing switch-on threshold Zero crossing switch-off threshold Reverse phase control Ramp current setting Input current Input voltage Ramp Charging current 1 Charging current 2 Discharge impedance Switch-on threshold, output stage Discharge threshold voltage Control voltage Input voltage Input current Programing, tri state input Input current Operating mode: Static zero-voltage switch 2-stage reverse phase control with it h ff switch-off 2-stage reverse phase control RC oscillator Input current Upper threshold Lower threshold Discharge impedance 10 (16) Test Conditions / Pin Symbol IS = 2 mA Pin 15 VS VS IS = 5 mA VS = 15 V Pin 15 IS Pin 15 VSON VSOFF V15 – I1 = 0 to 5 mA Pin 1 VRef I16 = 2 mA V16 = 0 V Pin 16-15 Pin 16 Pin 16 Pin 16 Pin 3 I3 = – 10 mA I3 = – 10 mA V13 vV vV vV vV 4 6 vV 5 Max. 17 17.2 2 Unit V 16.5 11.6 13.3 5.25 V mA 14.8 10.4 11.7 4.75 11 12.5 5 Vlimit – II VTON VTOFF 7.3 7.9 0.8 100 7.7 8.3 8.1 8.7 V V – II V3 5 50 5.3 mA 4.7 9 37 10 40 1 450 600 11 43 mA mA – Ich1 – Ich2 Rdis VTON Vdis V V mA V 490 kW mV mV I VRef 500 V nA I 1 mA VI l Pin 6 15 "I "I Pin 5 < 3.6 V " 410 0 VI V13 Typ. Pin 2 Pin 2-1 Pin 4 V13 Min. 15 15.2 II VTU VTL Rdis 1 VRef +1 VRef+0.3 +0 3 0 0.3 3.6 0.9 VS 4 1 1 500 4.4 1.1 V nA V V kW TELEFUNKEN Semiconductors Rev. A1, 30-May-96 U2102B Parameters Window discriminator Input current Upper threshold Lower threshold Input current window adjustment Minimum window: Lower threshold Upper threshold Maximum window: Lower threshold Upper threshold Enable-Schmitt trigger Input current Enable threshold Blocking threshold: Output stage OFF Output stage ON, except in the case of two-stage reverse phase control in second stage (a) Threshold for test mode Current monitoring Input current Switch-off threshold 1 Switch-off threshold 2 Switching output Leakage current Saturation voltage Push-pull output stage Upper saturation voltage, ON state Lower saturation voltage, OFF state Output current TELEFUNKEN Semiconductors Rev. A1, 30-May-96 Test Conditions / Pin 0V vV vV 8 Pin 8 Pins 8 and 9 l v vV 0 V V9 V9 = V13 1 V9 = V1 0V 0V Symbol Pin 9 Pin 8 "I i VTU VTL "I Min. 0.55 0.45 Typ. @V @V Ref + (0.2 Ref – (0.2 i Max. Unit 500 @V ) @V ) nA 9 9 V 500 nA VTL1 VTU1 2.05 2.55 2.75 3.75 2.45 2.95 V VTL2 VTU2 1.1 3.4 1.25 3.75 1.4 4.1 V 500 nA VT 2.3 2.5 2.7 V VT 1.8 0.45 2 0.5 2.2 0.55 V VT 85 100 115 mV 80 450 100 500 500 120 550 nA mV mV Ilkg 1 mA VSat VSat 1.0 1.2 V V – VSat 2.4 V VSatL 1.2 V Pin 8 Pin 7 vV vV 7 l vV vV 11 Pin 11 1 "I i "I i VT1 VT2 Pin 12 V11 < 450 mV, V12 V11 > 550 mV I12 = 0.5 mA I12 = 10 mA vV 15 I14 = – 10 mA Pins 14 and 15 I14 = 10 mA Pin 14 ON state OFF state Pin 14 –IO IO 50 50 mA 11 (16) U2102B Applications Vmains 230 V X 94 8221 Load GND 1 nF Rsh 22 kW/2 W R1 1 kW IGBT 100 W 1N4007 Rsync 220 kW RG C1 47 mF/ 25 V 100 kW NTC VRef VS 16 15 14 13 12 11 10 9 6 7 8 U2102B 1 2 3 C3 10 nF 4 5 R3 820 kW Control 100 kW VS GND 220 nF 22 kW 1 MW R2 Enable C2 CRef Trigger signal 1 mF Figure 9. House number or staircase illumination for ac loads House number illumination: V6 = V13 Staircase illumination: V6 = V15 12 (16) TELEFUNKEN Semiconductors Rev. A1, 30-May-96 U2102B Vmains 230 V X 94 8222 Load GND 1 nF Rsh 1 kW IGBT R1 = Rsync 18 kW/2 W 100 W RG 68 kW NTC VRef C1 47 mF/25 V 1N4007 VS 16 15 14 13 12 11 10 9 6 7 8 U2102B 1 2 3 C3 22 nF 4 5 R3 750 kW C2 220 nF Enable 22 kW 1 MW Trigger signal R2 CRef 1 mF Figure 10. Zero voltage switch mode for ac loads TELEFUNKEN Semiconductors Rev. A1, 30-May-96 13 (16) U2102B Vmains 230 V X 94 8502 Load 1 nF Rsh R1 22 kW/2 W 1 kW IGBT 100 W VS 1N4007 Rsync 220 kW RG C1 47 mF/ 25 V 100 kW 100 kW VS 16 15 14 13 12 11 10 9 6 7 8 U2102B 1 2 4 3 5 C3 100 kW 10 nF 100 kW R3 1 MW VS Control 100 kW CRef 1 mF Figure 11. Reverse phase control for ac loads 14 (16) TELEFUNKEN Semiconductors Rev. A1, 30-May-96 U2102B Dimensions in mm Package: DIP16 94 9128 Package: SO16 94 8875 TELEFUNKEN Semiconductors Rev. A1, 30-May-96 15 (16) U2102B Ozone Depleting Substances Policy Statement It is the policy of TEMIC TELEFUNKEN microelectronic GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances ( ODSs). The Montreal Protocol ( 1987) and its London Amendments ( 1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. TEMIC TELEFUNKEN microelectronic GmbH semiconductor division has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2 . Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency ( EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C ( transitional substances ) respectively. TEMIC can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use TEMIC products for any unintended or unauthorized application, the buyer shall indemnify TEMIC against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. TEMIC TELEFUNKEN microelectronic GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Telephone: 49 ( 0 ) 7131 67 2831, Fax number: 49 ( 0 ) 7131 67 2423 16 (16) TELEFUNKEN Semiconductors Rev. A1, 30-May-96