FAN256 — Dual Low Voltage Comparator Features Description Low Supply Current: IDD=7μA (Typical) The FAN256 is a low-power, dual comparator that typically consumes less than 10µA supply current per comparator. Guaranteed to operate at a low voltage of 1.6V and fully operational up to 5.5V, it is convenient for use in 1.8, 3.0V, and 5.0V systems. Push-Pull Output Circuit Single Power Supply Operation Wide Common-Mode Input Voltage Range: Rail-to-Rail The FAN256 has a complementary push-pull P- and Nchannel output stage capabile of driving a rail-to-rail output swing with a load ranging up to 5.0mA. Low Input Bias Current Internal Hysteresis VDD Packaged in MicroPak™ 8 (1.6mm x 1.6mm) Applications Mobile Phones Alarm and Security Systems IN(-) A 2 - IN(+) A 3 + 1 Out A Personal Digital Assistants IN(-) B IN(+) B 6 5 + + 7 Out B VSS Figure 1. Functional Diagram Ordering Information Part Number Top Mark FAN256L8X CP © 2010 Fairchild Semiconductor Corporation FAN256 • Rev. 1.0.0 Operating Temperature Range Package Packing Method -40 to 85°C 8-Lead, MicroPak™ 1.6mm x 1.6mm Package 5000 Units on Tape and Reel www.fairchildsemi.com FAN256 — Dual Low Voltage Comparator May 2011 FAN256 — Dual Low Voltage Comparator Pin Configuration OUT B IN(-) B 7 IN(+) B 6 5 4 8 VDD 1 2 OUT A VSS 3 IN(-) A IN(+) A Figure 2. Pin Configuration (Top Through View) Pin Definitions Pin # Name Description 1 OUT A Comparator A Output 2 IN(-) A Inverting Input of Comparator A 3 IN(+) A 4 VSS 5 IN(+) B Non-Inverting Input of Comparator B 6 IN(-) B Inverting Input of Comparator B 7 OUT B 8 VDD Non-Inverting Input of Comparator A Negative Supply Voltage Comparator B Output Positive Supply Voltage Function Table Inputs Outputs IN(-) > IN(+) Output LOW IN(+) > IN(-) Output HIGH VDD VOUT VIN(-) VDD VOUT VOUT VOUT VIN (+) VIN (-) VIN(+) Figure 3. VIN vs. VOUT © 2010 Fairchild Semiconductor Corporation FAN256 • Rev. 1.0.0 www.fairchildsemi.com 2 Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol VDD to VSS DVIN VIN Parameter Condition Supply Voltage Max. -3.0 +3.0 0 6.0 Differential Input Voltage Unit V ±6 Input Voltage (1) ts Output Short Circuit Duration TJ Junction Temperature TSTG Min. Storage Temperature Range -65 VSS to VDD V Indefinite S +150 °C +150 °C PD Power Dissipation 226 mW JA Thermal Resistance 287 °C/W IEC 61000-4-2 System ESD ESD JEDEC JESD22-A114, Human Body Model JEDEC JESD22-C101, Charged Device Model Air Gap 15 Contact 8 All Pins 8 Pin to Pin: IN(-), IN(+) to VDD or VSS 12 All Pins 2 FAN256 — Dual Low Voltage Comparator Absolute Maximum Ratings kV Note: 1. The maximum total power dissipation must not be exceeded. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol VDD to VSS Parameter Power Supply VDD Power Supply VIN Input Voltage IOH/IOL Condition Output Sink/Source Current VSS=0V Min. Max. -2.75 +2.75 0 5.5 1.6 © 2010 Fairchild Semiconductor Corporation FAN256 • Rev. 1.0.0 5.5 V V 5 VDD=3.0V 3 Operating Temperature, Free Air V VSS to VDD VDD=5.0V VDD=1.6V TA Unit mA 1 -40 +85 °C www.fairchildsemi.com 3 Symbol Parameter Condition Min. Typ. Max. Unit VDD=5.5V, VSS=GND, and TA=+25°C VHYS Input Hysteresis VCM=0.5VDD (2) Input Offset Voltage IIO Input Offset Current 10 pA II Input Bias Current 10 pA Common Mode Input Voltage Common Mode Rejection Ratio(3) IDD Supply Current - Per Comparator Power Supply Rejection Ratio ±1 VSS CMRR PSRR -15 mV VIO VCM VCM=0.5VDD 4 VDD VCM=VDD (3) 68 7 ΔVDD=0.5V 45 60 VO=VSS 90 Low-Level Output Voltage ISINK=5.0mA 0.1 VOH High-Level Output Voltage ISOURCE=5.0mA tPLH Propagation Delay (Turn-On) tPHL Propagation Delay (Turn-Off) Output Short Circuit Current VOL tTLH tTHL (4) Response Time, Output Rise/Fall 5.2 mV V dB 17 80 VO=VDD IOS +15 µA dB mA 0.3 V 5.4 V Overdrive=20mV, CL=15pF 0.40 µs Overdrive=20mV, CL=15pF 0.42 µs 4.0 CL=50pF FAN256 — Dual Low Voltage Comparator Electrical Characteristics ns 5.4 VDD=3V, VSS=GND, and TA=+25°C VHYS Input Hysteresis VCM=0.5VDD (2) Input Offset Voltage IIO Input Offset Current 10 pA II Input Bias Current 10 pA CMRR IDD PSRR Common Mode Input Voltage Common Mode Rejection Ratio 60 Supply Current(x) Per Comparator Power Supply Rejection Ratio(3) 6 ΔVDD=0.5V VO=VSS 35 ISINK=3.0mA VOH High-Level Output Voltage ISOURCE=3.0mA tPLH Propagation Delay (Turn-On) tPHL Propagation Delay (Turn-Off) (4) 0.15 V 15 µA dB mA 0.35 V 2.85 V Overdrive=20mV, CL=15pF 0.45 µs Overdrive=20mV, CL=15pF 0.47 µs CL=50pF 2.65 mV dB 70 27 Low-Level Output Voltage Response Time, Output Rise/Fall 45 VO=VDD VOL +15 VDD VCM=VDD Output Short Circuit Current tTHL ±1 VSS (3) IOS tTLH -15 mV VIO VCM VCM=0.5VDD 4 6.1 6.2 ns Continued on the following page… © 2010 Fairchild Semiconductor Corporation FAN256 • Rev. 1.0.0 www.fairchildsemi.com 4 Symbol Parameter Condition Min. Typ. Max. Unit VDD=1.6V, VSS=GND, and TA=+25°C VHYS Input Hysteresis VIO Input Offset Voltage IIO Input Offset Current II Input Bias Current VCM CMRR IDD PSRR VCM=0.5VDD (2) VCM=0.5VDD (3) VCM=VDD 5.5 VO=VSS 7.5 Low-Level Output Voltage ISINK=1.0mA High-Level Output Voltage ISOURCE=1.0mA tPLH Propagation Delay (Turn-On) tPHL Propagation Delay (Turn-Off) (4) Response Time, Output Rise/Fall 0.15 13 µA dB mA 0.25 V 1.50 V Overdrive=20mV, CL=15pF 0.52 µs Overdrive=20mV, CL=15pF 0.54 µs CL=50pF 1.35 V dB 70 VO=VDD VOL pA 56 45 mV pA VDD 5 ΔVDD=0.5V VOH tTHL +15 10 Supply Current(x) Per Comparator Output Short Circuit Current ±1 VSS Power Supply Rejection Ratio(3) IOS tTLH -15 mV 10 Common Mode Input Voltage Common Mode Rejection Ratio 3.5 16.5 13.0 FAN256 — Dual Low Voltage Comparator Electrical Characteristics ns Notes: 2. Differential input switching level is guaranteed at the minimum or maximum offset voltage, minus or plus half the maximum hysteresis voltage. 3. Guaranteed by design and characterization data 4. Input signal: 1kHz, square-wave signal with 10ns edge rate. © 2010 Fairchild Semiconductor Corporation FAN256 • Rev. 1.0.0 www.fairchildsemi.com 5 900 15.00 VDD=1.6V 800 14.00 VDD=3.0V 700 1.6 VDD 13.00 VDD=5.5V 600 3.0 VDD 500 5.5 VDD ICC (µA) IDD , Supply Current (µA) 16.00 12.00 11.00 400 300 10.00 200 9.00 100 0 8.00 -55 ⁰C -40 ⁰C Includes both Comparators -25 ⁰C 25 ⁰C 85 ⁰C 0.01 95 ⁰C 0.1 1 Temp. =25C CL = 15pF TA, Ambient Temperature Figure 4. Supply Current vs. Temperature 10 100 1000 Frequency (Khz) Figure 5. Supply Current vs. Output Transition Frequency 6 FAN256 — Dual Low Voltage Comparator Typical Performance Characteristics 5.5 VOH, Output Voltage HIGH State (V) IDD, Supply Current (µA) 16 14 12 10 8 ‐40 ⁰C 6 25 ⁰C 4 85 ⁰C 2 0 0 0.5 * Data includes both comparators 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 5 4.5 4 3.5 3 2.5 2 VDD=1.6V 1.5 VDD=3.0V 1 V DD, Supply Voltage (V) VDD=5.5V 0.5 0 2 4 6 8 10 ISOURCE, Output Source Current (mA) Figure 6. Supply Current vs. Supply Voltage Figure 7. Output HIGH vs. Output Drive Current 380 360 340 100 320 tPHL (ns) VOL , Output Voltage Low (mV) 400 1000 VDD=1.6V 10 300 280 VDD=3.0V 1.6VDD 260 VDD=5.5V 3.0VDD 240 5.5VDD 1 220 0.10 1.00 10.00 200 ISINK , Output Sink Current (mA) -60 -40 -20 0 20 40 60 80 100 Temperature Figure 8. Figure 9. Propagation Delay (tPHL) vs. Temperature Output LOW vs. Output Drive Current © 2010 Fairchild Semiconductor Corporation FAN256 • Rev. 1.0.0 www.fairchildsemi.com 6 300 500 280 260 450 Delay (nS) 240 tPLH (ns) 400 350 300 220 200 180 1.6VDD 3.0VDD 160 tpLH 140 tpHL 120 250 5.5VDD 100 200 -60 -40 -20 0 20 40 60 80 0 100 Figure 10. Propagation Delay (tPLH) vs. Temperature 100 150 200 250 Overdrive (mV) Figure 11. Propagation Delay vs. Input Overdrive 3 2 TA = 25°C 7 6 1 5 Voltage (V) Input Common Mode Voltage Range (V) 50 VDD=3.0V Temp. =25°C Temperature FAN256 — Dual Low Voltage Comparator Typical Performance Characteristics (Continued) 0 ‐1 ‐2 4 3 2 VDD 1 Output 0 ‐3 0 1 2 3 4 5 6 50 100 Input Overdrive = 50mV 150 200 250 300 Time (µS) Vs, Supply Voltage (V) Figure 13. Power-Up Delay Figure 12. Input Common Mode Voltage Range vs. Supply Voltage © 2010 Fairchild Semiconductor Corporation FAN256 • Rev. 1.0.0 www.fairchildsemi.com 7 FAN256 — Dual Low Voltage Comparator Physical Dimensions 0.10 2X C A 1.6 B 1.6 INDEX AREA 0.10 2X C TOP VIEW 0.55 MAX 0.05 0.05 0.00 DETAIL A 8X(0.09) C 8X 0.05 Recommended Landpattern C (0.20) 1.0 2 1 4 (0.1) C 8 0.35 0.25 3X(0.2) 0.35 0.25 0.5 3 4 7 6 5 (0.15) 0.15 8X 0.25 0.10 0.05 C A B C 0.35 0.25 DETAIL A PIN #1 TERMINAL SCALE: 2X BOTTOM VIEW Notes: 1. PACKAGE CONFORMS TO JEDEC MO-255 VARIATION UAAD 2. DIMENSIONS ARE IN MILLIMETERS 3. DRAWING CONFORMS TO ASME Y.14M-1994 4. PIN 1 FLAG, END OF PACKAGE OFFSET 5. DRAWING FILE NAME: MKT-MAC08AREV4 MAC08AREV4 Figure 14. 8-Lead, MicroPak™ 1.6mm Wide Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. Tape and Reel Specifications Please visit Fairchild Semiconductor’s online packaging area for the most recent tape and reel specifications: hhttp://www.fairchildsemi.com/products/logic/pdf/micropak_tr.pdf/ © 2010 Fairchild Semiconductor Corporation FAN256 • Rev. 1.0.0 www.fairchildsemi.com 8 FAN256 — Dual Low Voltage Comparator © 2010 Fairchild Semiconductor Corporation FAN256 • Rev. 1.0.0 www.fairchildsemi.com 9