K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM 36Mb QDRII SRAM Specification 165 FBGA with Pb & Pb-Free (RoHS compliant) INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO SAMSUNG PRODUCTS, AND IS SUBJECT TO CHANGE WITHOUT NOTICE. NOTHING IN THIS DOCUMENT SHALL BE CONSTRUED AS GRANTING ANY LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IN SAMSUNG PRODUCTS OR TECHNOLOGY. ALL INFORMATION IN THIS DOCUMENT IS PROVIDED ON AS "AS IS" BASIS WITHOUT GUARANTEE OR WARRANTY OF ANY KIND. 1. For updates or additional information about Samsung products, contact your nearest Samsung office. 2. Samsung products are not intended for use in life support, critical care, medical, safety equipment, or similar applications where Product failure could result in loss of life or personal or physical harm, or any military or defense application, or any governmental procurement to which special terms or provisions may apply. * Samsung Electronics reserves the right to change products or specification without notice. -1- Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM Document Title 1Mx36-bit, 2Mx18 and 4Mx9-bit QDRTM II b4 SRAM Revision History History Draft Date Remark 0.0 1. Initial document. Jan. 17, 2006 Advance 0.1 1. Put the data in the table of DC Characteristics, Pin Capacitance and Thermal Resistance. Apr. 26. 2006 Preliminary 0.2 1. Add 300MHz Bin 2. Change AC Characteristics. May. 4. 2006 Preliminary 0.3 1. Change Samsung JEDEC Code in ID REGISTER DEFINITION Jun. 05, 2006 Preliminary 0.4 1. Add x9 Organization. Jun. 15, 2006 Preliminary 1.0 1. Final 2. Change Vss/SA to NC/SA in Pin Configuration Jul. 10, 2006 Final 1.1 1. Correct typo Aug. 23, 2006 Final Rev. No. -2- Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM 1Mx36-bit, 2Mx18 and 4Mx9-bit QDRTM II b4 SRAM FEATURES • 1.8V+0.1V/-0.1V Power Supply. • DLL circuitry for wide output data valid window and future frequency scaling. • I/O Supply Voltage 1.5V+0.1V/-0.1V for 1.5V I/O, 1.8V+0.1V/-0.1V for 1.8V I/O. • Separate independent read and write data ports with concurrent read and write operation • HSTL I/O • Full data coherency, providing most current data. • Synchronous pipeline read with self timed late write. • Registered address, control and data input/output. • DDR (Double Data Rate) Interface on read and write ports. • Fixed 4-bit burst for both read and write operation. • Clock-stop supports to reduce current. • Two input clocks (K and K) for accurate DDR timing at clock rising edges only. • Two input clocks for output data (C and C) to minimize clock-skew and flight-time mismatches. • Two echo clocks (CQ and CQ) to enhance output data traceability. • Single address bus. • Byte write (x9, x18, x36) function. • Separate read/write control pin (R and W) • Simple depth expansion with no data contention. • Programmable output impedance. • JTAG 1149.1 compatible test access port. • 165FBGA(11x15 ball array) with body size of 15mmx17mm. & Lead Free • Operating in commercial and industrial temperature range. Part Number Org. X36 X18 X9 Cycle Access Unit Time Time K7R323684C-F(E)C(I)33 3.0 0.45 ns K7R323684C-F(E)C(I)30 3.3 0.45 ns K7R323684C-F(E)C(I)25 4.0 0.45 ns K7R321884C-F(E)C(I)33 3.0 0.45 ns K7R321884C-F(E)C(I)30 3.3 0.45 ns K7R321884C-F(E)C(I)25 4.0 0.45 ns K7R320984C-F(E)C(I)33 3.0 0.45 ns K7R320984C-F(E)C(I)30 3.3 0.45 ns K7R320984C-F(E)C(I)25 4.0 0.45 ns * -F(E)C(I) F(E) [Package type] : E-Pb Free, F-Pb C(I) [Operating Temperature] : C-Commercial, I-Industrial FUNCTIONAL BLOCK DIAGRAM DATA REG K K C WRITE DRIVER 18 CTRL LOGIC 4 (or 2) 1Mx36 (2Mx18 4Mx9) MEMORY ARRAY 72 (or 36) 72 (or 36) 144 (or 72) OUTPUT DRIVER (or 19,20) OUTPUT SELECT R W BWX 72(or 36) OUTPUT REG 18 (or 19,20) ADD ADDRESS REG 72(or 36) SENSE AMPS 36 (or 18) WRITE/READ DECODE D (Data in) 36 (or 18) Q (Data Out) CQ, CQ (Echo Clock out) CLK GEN SELECT OUTPUT CONTROL C Notes: 1. Numbers in ( ) are for x18,x9 device QDR SRAM and Quad Data Rate comprise a new family of products developed by Cypress, Renesas, IDT, NEC and Samsung technology. -3- Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM PIN CONFIGURATIONS(TOP VIEW) K7R323684C(1Mx36) 1 2 3 4 5 6 7 8 9 10 11 A CQ NC/SA* NC/SA* W BW2 K BW1 R SA NC/SA* CQ B Q27 Q18 D18 SA BW3 K BW0 SA D17 Q17 Q8 C D27 Q28 D19 VSS SA NC SA VSS D16 Q7 D8 D D28 D20 Q19 VSS VSS VSS VSS VSS Q16 D15 D7 E Q29 D29 Q20 VDDQ VSS VSS VSS VDDQ Q15 D6 Q6 F Q30 Q21 D21 VDDQ VDD VSS VDD VDDQ D14 Q14 Q5 G D30 D22 Q22 VDDQ VDD VSS VDD VDDQ Q13 D13 D5 H Doff VREF VDDQ VDDQ VDD VSS VDD VDDQ VDDQ VREF ZQ J D31 Q31 D23 VDDQ VDD VSS VDD VDDQ D12 Q4 D4 K Q32 D32 Q23 VDDQ VDD VSS VDD VDDQ Q12 D3 Q3 L Q33 Q24 D24 VDDQ VSS VSS VSS VDDQ D11 Q11 Q2 M D33 Q34 D25 VSS VSS VSS VSS VSS D10 Q1 D2 N D34 D26 Q25 VSS SA SA SA VSS Q10 D9 D1 P Q35 D35 Q26 SA SA C SA SA Q9 D0 Q0 R TDO TCK SA SA SA C SA SA SA TMS TDI Notes : 1. * Checked No Connect (NC) pins are reserved for higher density address, i.e. 3A for 72Mb, 10A for 144Mb and 2A for 288Mb. 2. BW0 controls write to D0:D8, BW1 controls write to D9:D17, BW2 controls write to D18:D26 and BW3 controls write to D27:D35. PIN NAME SYMBOL PIN NUMBERS DESCRIPTION K, K 6B, 6A Input Clock C, C 6P, 6R Input Clock for Output Data CQ, CQ 11A, 1A Output Echo Clock Doff 1H DLL Disable when low SA 9A,4B,8B,5C,7C,5N-7N,4P,5P,7P,8P,3R-5R,7R-9R Address Inputs D0-35 10P,11N,11M,10K,11J,11G,10E,11D,11C,10N,9M,9L 9J,10G,9F,10D,9C,9B,3B,3C,2D,3F,2G,3J,3L,3M,2N 1C,1D,2E,1G,1J,2K,1M,1N,2P Data Inputs Q0-35 11P,10M,11L,11K,10J,11F,11E,10C,11B,9P,9N,10L 9K,9G,10F,9E,9D,10B,2B,3D,3E,2F,3G,3K,2L,3N 3P,1B,2C,1E,1F,2J,1K,1L,2M,1P Data Outputs W 4A Write Control Pin, active when low R 8A Read Control Pin, active when low BW0, BW1,BW2, BW3 7B,7A,5A,5B Block Write Control Pin, active when low VREF 2H,10H Input Reference Voltage ZQ 11H Output Driver Impedance Control Input VDD 5F,7F,5G,7G,5H,7H,5J,7J,5K,7K Power Supply (1.8 V) VDDQ 4E,8E,4F,8F,4G,8G,3H,4H,8H,9H,4J,8J,4K,8K,4L,8L Output Power Supply (1.5V or 1.8V) VSS 4C,8C,4D-8D,5E-7E,6F,6G,6H,6J,6K,5L-7L,4M, 8M,4N,8N Ground TMS 10R JTAG Test Mode Select JTAG Test Data Input TDI 11R TCK 2R JTAG Test Clock TDO 1R JTAG Test Data Output NC 2A,3A,10A,6C No Connect NOTE 1 2 3 Notes: 1. C, C, K or K cannot be set to VREF voltage. 2. When ZQ pin is directly connected to VDD output impedance is set to minimum value and it cannot be connected to ground or left unconnected. 3. Not connected to chip pad internally. -4- Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM PIN CONFIGURATIONS(TOP VIEW) K7R321884C(2Mx18) 1 2 3 4 5 A CQ NC/SA* B NC Q9 6 7 8 SA W BW1 K NC D9 SA NC K BW0 9 10 11 R SA NC/SA* CQ SA NC NC Q8 C NC NC D10 VSS SA NC SA VSS NC Q7 D8 D NC D11 Q10 VSS VSS VSS VSS VSS NC NC D7 E NC NC Q11 VDDQ VSS VSS VSS VDDQ NC D6 Q6 F NC Q12 D12 VDDQ VDD VSS VDD VDDQ NC NC Q5 G NC D13 Q13 VDDQ VDD VSS VDD VDDQ NC NC D5 H Doff VREF VDDQ VDDQ VDD VSS VDD VDDQ VDDQ VREF ZQ J NC NC D14 VDDQ VDD VSS VDD VDDQ NC Q4 D4 K NC NC Q14 VDDQ VDD VSS VDD VDDQ NC D3 Q3 L NC Q15 D15 VDDQ VSS VSS VSS VDDQ NC NC Q2 M NC NC D16 VSS VSS VSS VSS VSS NC Q1 D2 N NC D17 Q16 VSS SA SA SA VSS NC NC D1 P NC NC Q17 SA SA C SA SA NC D0 Q0 R TDO TCK SA SA SA C SA SA SA TMS TDI Notes: 1. * Checked No Connect (NC) pins are reserved for higher density address, i.e. 10A for 72Mb and 2A for 144Mb. 2. BW0 controls write to D0:D8 and BW1 controls write to D9:D17. PIN NAME SYMBOL PIN NUMBERS DESCRIPTION K, K 6B, 6A Input Clock C, C 6P, 6R Input Clock for Output Data CQ, CQ 11A, 1A Output Echo Clock Doff 1H DLL Disable when low SA 3A,9A,4B,8B,5C,7C,5N-7N,4P,5P,7P,8P,3R-5R,7R-9R Address Inputs D0-17 10P,11N,11M,10K,11J,11G,10E,11D,11C,3B,3C,2D 3F,2G,3J,3L,3M,2N Data Inputs Q0-17 11P,10M,11L,11K,10J,11F,11E,10C,11B,2B,3D,3E 2F,3G,3K,2L,3N,3P Data Outputs W 4A Write Control Pin, active when low R 8A Read Control Pin, active when low BW0, BW1 7B, 5A Block Write Control Pin, active when low VREF 2H,10H Input Reference Voltage ZQ 11H Output Driver Impedance Control Input VDD 5F,7F,5G,7G,5H,7H,5J,7J,5K,7K Power Supply (1.8 V) VDDQ 4E,8E,4F,8F,4G,8G,3H,4H,8H,9H,4J,8J,4K,8K,4L,8L Output Power Supply (1.5V or 1.8V) VSS 4C,8C,4D-8D,5E-7E,6F,6G,6H,6J,6K,5L-7L,4M-8M,4N,8N Ground TMS 10R JTAG Test Mode Select TDI 11R JTAG Test Data Input TCK 2R JTAG Test Clock TDO 1R JTAG Test Data Output NC 2A,10A,7A,1B,5B,9B,10B,1C,2C,6C,9C,1D,9D,10D,1E,2E,9E,1F 9F,10F,1G,9G,10G,1J,2J,9J,1K,2K,9K,1L,9L,10L,1M 2M,9M,1N,9N,10N,1P,2P,9P No Connect NOTE 1 2 3 Notes: 1. C, C, K or K cannot be set to VREF voltage. 2. When ZQ pin is directly connected to VDD output impedance is set to minimum value and it cannot be connected to ground or left unconnected. 3. Not connected to chip pad internally. -5- Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM PIN CONFIGURATIONS(TOP VIEW) K7R360984C(4Mx9) 1 2 3 4 5 6 7 8 9 A CQ NC/SA* SA W NC K NC R B NC NC NC SA NC K BW SA 10 11 SA SA CQ NC NC Q3 C NC NC NC VSS SA NC SA VSS NC NC D3 D NC D4 NC VSS VSS VSS VSS VSS NC NC NC E NC NC Q4 VDDQ VSS VSS VSS VDDQ NC D2 Q2 F NC NC NC VDDQ VDD VSS VDD VDDQ NC NC NC G NC D5 Q5 VDDQ VDD VSS VDD VDDQ NC NC NC H Doff VREF VDDQ VDDQ VDD VSS VDD VDDQ VDDQ VREF ZQ J NC NC NC VDDQ VDD VSS VDD VDDQ NC Q1 D1 K NC NC NC VDDQ VDD VSS VDD VDDQ NC NC NC L NC Q6 D6 VDDQ VSS VSS VSS VDDQ NC NC Q0 M NC NC NC VSS VSS VSS VSS VSS NC NC D0 N NC D7 NC VSS SA SA SA VSS NC NC NC P NC NC Q7 SA SA C SA SA NC D8 Q8 R TDO TCK SA SA SA C SA SA SA TMS TDI Notes: 1. * Checked No Connect (NC) pins are reserved for higher density address, i.e. 2A for 72Mb. 2. BW controls write to D0:D8 . PIN NAME SYMBOL PIN NUMBERS DESCRIPTION K, K 6B, 6A Input Clock C, C 6P, 6R Input Clock for Output Data CQ, CQ 11A, 1A Output Echo Clock Doff 1H DLL Disable when low Address Inputs SA 3A,9A,10A,4B,8B,5C,7C,5N-7N,4P,5P,7P,8P,3R-5R,7R-9R D0-8 11M,11J,10E,11C,2D,2G,3L,2N,10P Data Inputs Q0-8 11L,10J,11E,11B,3E,3G,2L,3P,11P Data Outputs W 4A Write Control Pin, active when low R 8A Read Control Pin, active when low BW 7B Nybble Write Control Pin, active when low VREF 2H,10H Input Reference Voltage ZQ 11H Output Driver Impedance Control Input VDD 5F,7F,5G,7G,5H,7H,5J,7J,5K,7K Power Supply (1.8 V) VDDQ 4E,8E,4F,8F,4G,8G,3H,4H,8H,9H,4J,8J,4K,8K,4L,8L Output Power Supply (1.5V or 1.8V) VSS 4C,8C,4D-8D,5E-7E,6F,6G,6H,6J,6K,5L-7L,4M-8M,4N,8N Ground TMS 10R JTAG Test Mode Select TDI 11R JTAG Test Data Input TCK 2R JTAG Test Clock TDO 1R JTAG Test Data Output NC 2A,7A,5A,1B,2B,3B,5B,9B,10B,1C,2C,3C,6C,9C,10C,1D,3D,9D, 10D,11D,1E,2E,9E,1F,2F,3F,9F,10F,11F,1G,9G,10G,11G,1J,2J, 3J,9J,1K,2K,3K,10K,11K,9K,1L,9L,10L,1M,2M,3M,9M,10M,1N,3N ,9N,10N,11N,1P,2P,9P No Connect NOTE 1 2 3 Notes: 1. C, C, K or K cannot be set to VREF voltage. 2. When ZQ pin is directly connected to VDD output impedance is set to minimum value and it cannot be connected to ground or left unconnected. 3. Not connected to chip pad internally. -6- Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM GENERAL DESCRIPTION The K7R323684C, K7R321884C and K7R320984C are 37,748,736-bits QDR (Quad Data Rate) Synchronous Pipelined Burst SRAMs. They are organized as 1,048,576 words by 36bits for K7R323684C and 2,097,152 words by 18 bits for K7R321884C and 4,194,304 words by 9 bits for K7R320984C. The QDR operation is possible by supporting DDR read and write operations through separate data output and input ports with the same cycle. Memory bandwidth is maximized as data can be transferred into SRAM on every rising edge of K and K, and transferred out of SRAM on every rising edge of C and C. And totally independent read and write ports eliminate the need for high speed bus turn around. Address for read and write are latched on alternate rising edges of the input clock K. Data inputs, and all control signals are synchronized to the input clock (K or K). Normally data outputs are synchronized to output clocks (C and C), but when C and C are tied high, the data outputs are synchronized to the input clocks (K and K). Read data are referenced to echo clock (CQ or CQ) outputs. Common address bus is used to access address both for read and write operations. The internal burst counter is fixed to 4-bit sequential for both read and write operations, requiring tow full clock bus cycles. Any request that attempts to interrupt a burst operation in progress is ignored. Synchronous pipeline read and late write enable high speed operations. Simple depth expansion is accomplished by using R and W for port selection. Byte write operation is supported with BW0 and BW1 (BW2 and BW3) pins. IEEE 1149.1 serial boundary scan (JTAG) simplifies monitoring package pads attachment status with system. The K7R323684C, K7R321884C and K7R320984C are implemented with SAMSUNG's high performance 6T CMOS technology and is available in 165pin FBGA packages. Multiple power and ground pins minimize ground bounce. Read Operations Read cycles are initiated by activating R at the rising edge of the positive input clock K. Address is presented and stored in the read address register synchronized with K clock. For 4-bit burst DDR operation, it will access four 36-bit, 18-bit or 9-bit data words with each read command. The first pipelined data is transferred out of the device triggered by C clock following next K clock rising edge. Next burst data is triggered by the rising edge of following C clock rising edge. The process continues until all four data are transferred. Continuous read operations are initiated with K clock rising edge. And pipelined data are transferred out of device on every rising edge of both C and C clocks. In case C and C tied to high, output data are triggered by K and K instead of C and C. When the R is disabled after a read operation, the K7R323684C, K7R321884C and K7R320984C will first complete burst read operation before entering into deselect mode at the next K clock rising edge. Then output drivers disabled automatically to high impedance state. Write Operations Write cycles are initiated by activating W at the rising edge of the positive input clock K. Address is presented and stored in the write address register synchronized with K clock. For 4-bit burst DDR operation, it will write four 36-bit, 18-bit or 9-bit data words with each write command. The first “late” data is transferred and registered in to the device synchronous with next K clock rising edge. Next burst data is transferred and registered synchronous with following K clock rising edge. The process continues until all four data are transferred and registered. Continuous write operations are initiated with K rising edge. And “late write” data is presented to the device on every rising edge of both K and K clocks. The device disregards input data presented on the same cycle W disabled. When the W is disabled after a read operation, the K7R323684C, K7R321884C and K7R320984C will first complete burst read operation before entering into deselect mode at the next K clock rising edge. The K7R323684C, K7R321884C and K7R320984C support byte write operations. With activating BW0 or BW1 (BW2 or BW3) in write cycle, only one byte of input data is presented. In K7R321884C, BW0 controls write operation to D0:D8, BW1 controls write operation to D9:D17. And in K7R323684C BW2 controls write operation to D18:D26, BW3 controls write operation to D27:D35. And in K7R320984C BW controls write operation to D0:D8. -7- Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM Single Clock Mode The K7R323684C, K7R321884C and K7R320984C can be operated with the single clock pair K and K, instead of C or C for output clocks. To operate these devices in single clock mode, C and C must be tied high during power up and must be maintained high during operation. After power up, this device can’t change to or from single clock mode. System flight time and clock skew could not be compensated in this mode. Depth Expansion Separate input and output ports enables easy depth expansion. Each port can be selected and deselected independently and read and write operation do not affect each other. Before chip deselected, all read and write pending operations are completed. Programmable Impedance Output Buffer Operation The designer can program the SRAM's output buffer impedance by terminating the ZQ pin to VSS through a precision resistor(RQ). The value of RQ (within 15%) is five times the output impedance desired. For example, 250Ω resistor will give an output impedance of 50Ω. Impedance updates occur early in cycles that do not activate the outputs, such as deselect cycles. In all cases impedance updates are transparent to the user and do not produce access time "push-outs" or other anomalous behavior in the SRAM. There are no power up requirements for the SRAM. However, to guarantee optimum output driver impedance after power up, the SRAM needs 1024 non-read cycles. Echo clock operation To assure the output traceability, the SRAM provides the output Echo clock, pair of compliment clock CQ and CQ, which are synchronized with internal data output. Echo clocks run free during normal operation. The Echo clock is triggered by internal output clock signal, and transferred to external through same structures as output driver. Clock Consideration K7R323684C, K7R321884C and K7R320984C utilizes internal DLL (Delay-Locked Loops) for maximum output data valid window. It can be placed into a stopped-clock state to minimize power with a modest restart time of 1024 clock cycles. Circuitry automatically resets the DLL when absence of input clock is detected. Power-Up/Power-Down Supply Voltage Sequencing The following power-up supply voltage application is recommended: VSS, VDD, VDDQ, VREF, then VIN. VDD and VDDQ can be applied simultaneously, as long as VDDQ does not exceed VDD by more than 0.5V during power-up. The following power-down supply voltage removal sequence is recommended: VIN, VREF, VDDQ, VDD, VSS. VDD and VDDQ can be removed simultaneously, as long as VDDQ does not exceed VDD by more than 0.5V during power-down. -8- Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM Detail Specification of Power-Up Sequence in QDRII SRAM QDRII SRAMs must be powered up and initialized in a predefined manner to prevent undefined operations. • Power-Up Sequence 1. Apply power and keep Doff at low state (All other inputs may be undefined) - Apply VDD before VDDQ - Apply VDDQ before VREF or the same time with VREF 2. Just after the stable power and clock (K, K, C, C), take Doff to be high. 3. The additional 1024cycles of clock input is required to lock the DLL after enabling DLL * Notes: If you want to tie up the Doff pin to High with unstable clock, then you must stop the clock for a few seconds (Min. 30ns) to reset the DLL after it become a stable clock status. • DLL Constraints 1. DLL uses either K or C clock as its synchronizing input, the input should have low phase jitter which is specified as TKC var. 2. The lower end of the frequency at which the DLL can operate is 8.4ns. 3. If the incoming clock is unstable and the DLL is enabled, then the DLL may lock onto a wrong frequency and this may cause the failure in the initial stage. K,K Status Power-Up ~ ~ ~ ~ ~ ~ Power up & Initialization Sequence (Doff pin controlled) 1024 cycle Unstable CLKstage DLL Locking Range Any Command Inputs Clock must be stable VDD VDDQ VREF Doff Power-Up Unstable CLKstage Stop Clock 1024 cycle ~ ~ Status ~ Min 30ns ~ ~ K,K ~ ~ ~ Power up & Initialization Sequence (Doff pin Fixed high, Clock controlled) DLL Locking Range Any Command Inputs Clock must be stable VDD VDDQ VREF * Notes: When the operating frequency is changed, DLL reset should be required again. After DLL reset again, the minimum 1024 cycles of clock input is needed to lock the DLL. -9- Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM TRUTH TABLES SYNCHRONOUS TRUTH TABLE K R W Stopped X ↑ H D Q OPERATION D(A1) D(A2) D(A3) D(A4) Q(A1) Q(A2) Q(A3) Q(A4) X Previous state Previous state Previous state Previous state Previous state Previous state Previous state Previous state Clock Stop H X X X X High-Z High-Z High-Z High-Z No Operation DOUT at C(t+2) DOUT at C(t+2) DOUT at C(t+3) Read X X X Write ↑ L4 X X X X X DOUT at C(t+1) ↑ H5 L4 Din at K(t+1) Din at K(t+1) Din at K(t+2) Din at K(t+2) X Notes: 1. X means "Don′t Care”. 2. The rising edge of clock is symbolized by ( ↑ ). 3. Before enter into clock stop status, all pending read and write operations will be completed. 4. This signal was HIGH on previous K clock rising edge. Initiating consecutive READ or WRITE operations on consecutive K clock rising edges is not permitted. The device will ignore the second request. 5. If this signal was LOW to initiated the previous cycle, this signal becomes a don′t care for this operation however it is strongly recommended that this signal is brought HIGH as shown in the truth table. WRITE TRUTH TABLE(x18) K K BW0 BW1 L L WRITE ALL BYTEs ( K↑ ) L L WRITE ALL BYTEs ( K↑ ) L H WRITE BYTE 0 ( K↑ ) L H WRITE BYTE 0 ( K↑ ) H L WRITE BYTE 1 ( K↑ ) H L WRITE BYTE 1 ( K↑ ) H H WRITE NOTHING ( K↑ ) H H WRITE NOTHING ( K↑ ) ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ OPERATION Notes: 1. X means “Don′t Care”. 2. All inputs in this table must meet setup and hold time around the rising edge of input clock K or K ( ↑ ). 3. Assumes a WRITE cycle was initiated. 4. This table illustrates operation for x18 devices. x9 device operation is similar except that BW controls D0:D8. WRITE TRUTH TABLE(x36) K K ↑ ↑ ↑ ↑ ↑ ↑ ↑ BW0 BW1 BW2 BW3 OPERATION L L L L WRITE ALL BYTEs ( K↑ ) L L L L WRITE ALL BYTEs ( K↑ ) L H H H WRITE BYTE 0 ( K↑ ) L H H H WRITE BYTE 0 ( K↑ ) H L H H WRITE BYTE 1 ( K↑ ) H L H H WRITE BYTE 1 ( K↑ ) H H L L WRITE BYTE 2 and BYTE 3 ( K↑ ) ↑ H H L L WRITE BYTE 2 and BYTE 3 ( K↑ ) H H H H WRITE NOTHING ( K↑ ) ↑ H H H H WRITE NOTHING ( K↑ ) ↑ Notes: 1. X means “Don′t Care”. 2. All inputs in this table must meet setup and hold time around the rising edge of input clock K or K (↑ ). 3. Assumes a WRITE cycle was initiated. - 10 - Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM ABSOLUTE MAXIMUM RATINGS* SYMBOL RATING UNIT Voltage on VDD Supply Relative to VSS PARAMETER VDD -0.5 to 2.9 V Voltage on VDDQ Supply Relative to VSS VDDQ -0.5 to VDD V VIN -0.5 to VDD+0.3 V TSTG -65 to 150 °C TOPR 0 to 70 / -40 to 85 °C TBIAS -10 to 85 °C Voltage on Input Pin Relative to VSS Storage Temperature Operating Temperature Commercial / Industrial Storage Temperature Range Under Bias *Note: 1. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VDDQ must not exceed VDD during normal operation. OPERATING CONDITIONS PARAMETER SYMBOL Min MAX UNIT VDD 1.7 1.9 V Supply Voltage Reference Voltage VDDQ 1.4 1.9 V VREF 0.68 0.95 V DC ELECTRICAL CHARACTERISTICS PARAMETER SYMBOL MIN TEST CONDITIONS MAX UNIT NOTES Input Leakage Current IIL VDD=Max; VIN=VSS to VDDQ -2 +2 µA Output Leakage Current IOL Output Disabled, -2 +2 µA -33 - 850 Operating Current (x36) ICC -30 - 800 -25 - 750 -33 - 800 -30 - 750 -25 - 700 -33 - 750 -30 - 700 -25 - 650 -33 - 350 -30 - 330 -25 - 300 Operating Current (x18) Operating Current (x9) Standby Current (NOP) ICC ICC ISB1 VDD=Max, IOUT=0mA Cycle Time ≥ tKHKH Min VDD=Max, IOUT=0mA Cycle Time ≥ tKHKH Min VDD=Max, IOUT=0mA Cycle Time ≥ tKHKH Min Device deselected, IOUT=0mA, f=Max, All Inputs≤0.2V or ≥ VDD-0.2V mA 1,5 mA 1,5 mA 1,5 mA 1,6 Output High Voltage VOH1 VDDQ/2-0.12 VDDQ/2+0.12 V 2,7 Output Low Voltage VOL1 VDDQ/2-0.12 VDDQ/2+0.12 V 3,7 Output High Voltage VOH2 IOH=-1.0mA VDDQ-0.2 VDDQ V 4 Output Low Voltage VOL2 IOL=1.0mA VSS 0.2 V 4 Input Low Voltage VIL -0.3 VREF-0.1 V 8,9 Input High Voltage VIH VREF+0.1 VDDQ+0.3 V 8,10 Notes: 1. Minimum cycle. IOUT=0mA. 2. |IOH|=(VDDQ/2)/(RQ/5)±15% for 175Ω ≤ RQ ≤ 350Ω. 3. |IOL|=(VDDQ/2)/(RQ/5)±15% for 175Ω ≤ RQ ≤ 350Ω. 4. Minimum Impedance Mode when ZQ pin is connected to VDD. 5. Operating current is calculated with 50% read cycles and 50% write cycles. 6. Standby Current is only after all pending read and write burst operations are completed. 7. Programmable Impedance Mode. 8. These are DC test criteria. DC design criteria is VREF±50mV. The AC VIH/VIL levels are defined separately for measuring timing parameters. 9. VIL (Min) DC=-0.3V, VIL (Min) AC=-1.5V(pulse width ≤ 3ns). 10. VIH (Max)DC=VDDQ+0.3, VIH (Max)AC=VDDQ+0.85V(pulse width ≤ 3ns) - 11 - Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM AC ELECTRICAL CHARACTERISTICS SYMBOL MIN MAX UNIT NOTES Input High Voltage PARAMETER VIH (AC) VREF + 0.2 - V 1,2 Input Low Voltage VIL (AC) - VREF - 0.2 V 1,2 Notes: 1. This condition is for AC function test only, not for AC parameter test. 2. To maintain a valid level, the transiting edge of the input must: a) Sustain a constant slew rate from the current AC level through the target AC level, VIL(AC) or VIH(AC) b) Reach at least the target AC level c) After the AC target level is reached, continue to maintain at least the target DC level, VIL(DC) or VIH(DC) AC TIMING CHARACTERISTICS PARAMETER SYMBOL -33 -30 -25 UNIT MIN MAX MIN MAX MIN MAX 3.00 8.40 3.30 8.40 4.00 8.40 ns 0.20 ns NOTE Clock Clock Cycle Time (K, K, C, C) tKHKH Clock Phase Jitter (K, K, C, C) tKC var Clock High Time (K, K, C, C) tKHKL 0.20 1.2 0.20 1.32 1.60 Clock Low Time (K, K, C, C) tKLKH 1.2 1.32 1.60 ns Clock to Clock (K↑ → K↑, C↑ → C↑) tKHKH 1.35 1.49 1.80 ns tKHCH 0.00 DLL Lock Time (K, C) tKC lock 1024 1024 1024 cycle K Static to DLL reset tKC reset 30 30 30 ns Clock to data clock (K↑ → C↑, K↑→ C↑) 1.30 0.00 1.45 0.00 5 ns 1.80 ns 6 Output Times C, C High to Output Valid tCHQV C, C High to Output Hold tCHQX C, C High to Echo Clock Valid tCHCQV C, C High to Echo Clock Hold tCHCQX CQ, CQ High to Output Valid tCQHQV CQ, CQ High to Output Hold tCQHQX 0.45 -0.45 0.45 -0.45 0.45 -0.45 0.45 -0.45 0.25 -0.25 0.45 -0.45 0.45 -0.45 0.27 -0.27 0.45 3 ns 3 ns ns 0.30 -0.30 0.45 ns 0.45 ns 7 ns 7 C, High to Output High-Z tCHQZ ns 3 C, High to Output Low-Z tCHQX1 -0.45 -0.45 -0.45 ns 3 tAVKH 0.40 0.40 0.50 ns Control inputs valid to K rising edge tIVKH 0.40 0.40 0.50 ns Data-in valid to K, K rising edge tDVKH 0.28 0.30 0.35 ns tKHAX 0.40 0.40 0.50 ns K rising edge to control inputs hold tKHIX 0.40 0.40 0.50 ns K, K rising edge to data-in hold tKHDX 0.28 0.30 0.35 ns Setup Times Address valid to K rising edge 2 Hold Times K rising edge to address hold Notes: 1. All address inputs must meet the specified setup and hold times for all latching clock edges. 2. Control singles are R, W,BW0,BW1 and (BW2, BW3, also for x36 and BW for x9) 3. If C,C are tied high, K,K become the references for C,C timing parameters. 4. To avoid bus contention, at a given voltage and temperature tCHQX1 is bigger than tCHQZ. The specs as shown do not imply bus contention because tCHQX1 is a MIN parameter that is worst case at totally different test conditions (0°C, 1.9V) than tCHQZ, which is a MAX parameter(worst case at 70°C, 1.7V) It is not possible for two SRAMs on the same board to be at such different voltage and temperature. 5. Clock phase jitter is the variance from clock rising edge to the next expected clock rising edge. 6. Vdd slew rate must be less than 0.1V DC per 50 ns for DLL lock retention. DLL lock time begins once Vdd and input clock are stable. 7. Echo clock is very tightly controlled to data valid/data hold. By design, there is a ± 0.1 ns variation from echo clock to data. The data sheet parameters reflect tester guard bands and test setup variations. - 12 - Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM THERMAL RESISTANCE SYMBOL TYP Unit Junction to Ambient PRMETER θJA 20.8 °C/W Junction to Case θJC 2.3 °C/W Junction to Pins θJB 4.3 °C/W NOTES Note: Junction temperature is a function of on-chip power dissipation, package thermal impedance, mounting site temperature and mounting site thermal impedance. TJ=TA + PD x θJA PIN CAPACITANCE PRMETER SYMBOL TESTCONDITION TYP MAX Unit CIN VIN=0V 3.5 4 pF Input and Output Capacitance COUT VOUT=0V 4 5 pF Clock Capacitance CCLK - 3 4 pF Address Control Input Capacitance NOTES Note: 1. Parameters are tested with RQ=250Ω and VDDQ=1.5V. 2. Periodically sampled and not 100% tested. AC TEST CONDITIONS AC TEST OUTPUT LOAD Symbol Value Unit Core Power Supply Voltage VDD 1.7~1.9 V Output Power Supply Voltage VDDQ 1.4~1.9 V Input High/Low Level VIH/VIL 1.25/0.25 V Input Reference Level VREF 0.75 V Input Rise/Fall Time TR/TF 0.3/0.3 ns VDDQ/2 V Parameter Output Timing Reference Level VREF 0.75V VDDQ/2 50Ω SRAM Zo=50Ω ZQ 250Ω Note: Parameters are tested with RQ=250Ω Overershoot Timing Undershoot Timing 20% tKHKH(MIN) VIH VDDQ+0.5V VDDQ+0.25V VSS VDDQ VSS-0.25V VSS-0.5V 20% tKHKH(MIN) VIL Note: For power-up, VIH ≤ VDDQ+0.3V and VDD ≤ 1.7V and VDDQ ≤ 1.4V t ≤ 200ms - 13 - Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM APPLICATION INRORMATION SRAM#1 Vt D SA R R=250Ω ZQ R=250Ω CQ CQ Q R W BW0 BW1 C C K K Data In Data Out Address R W BW SRAM#4 CQ CQ Q RW BW0 BW1 C C K K D SA R ZQ ZQ Vt Vt MEMORY CONTROLLER Return CLK Source CLK Return CLK Source CLK Vt Vt R=50Ω Vt=VREF SRAM1 Input CQ SRAM1 Input CQ SRAM4 Input CQ SRAM4 Input CQ - 14 - Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM TIMING WAVE FORMS OF READ AND NOP READ READ tKHKH K NOP NOP tKLKH tKHKH tKHKL K tAVKH tKHAX A1 SA A2 tIVKH tKHIX R tCHQX1 Q1-1 Q (Data Out) tKHKH tKHCH tKLKH tCHQV Q1-2 Q1-3 Q1-4 Q2-1 Q2-2 Q2-3 Q2-4 tCHQX C tKHKL tKHKH tCHQZ C tCHCQV tCHQV CQ tCQHQV CQ tCHCQX tCQHQX tCHCQV tCHCQX Don′t Care Undefined Note: 1. Q1-1 refers to output from address A1+0, Q1-2 refers to output from address A1+1 i.e. the next internal burst address following A1+0. 2. Outputs are disabled one cycle after a NOP. TIMING WAVE FORMS OF WRITE AND NOP WRITE WRITE tKHKH K NOP NOP tKLKH tKHKH tKHKL K tAVKH tKHAX A1 SA A2 tIVKH tKHIX tKHIX W D (Data In) D1-1 D1-2 D1-3 D1-4 D2-1 tDVKH D2-2 D2-3 D2-4 tKHDX Don′t Care Undefined Note: 1. D1-1 refers to input to address A1+0, D1-2 refers to input to address A1+1, i.e the next internal burst address following A1+0. 2. BWx (NWx) assumed active. - 15 - Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM TIMING WAVE FORMS OF READ, WRITE AND NOP READ WRITE READ WRITE NOP NOP K K A1 SA A2 A3 A4 W R D (Data In) D2-1 D2-2 D2-3 D2-4 D4-1 D4-2 D4-3 D (Data Out) Q1-1 Q1-2 Q1-3 Q1-4 Q3-1 Q3-2 Q3-3 C C Don′t Care Undefined Note: 1. If address A3=A2, data Q3-1=D2-1, data Q3-2=D2-2 , data Q3-3=D2-3, data Q3-4=D2-4 Write data is forwarded immediately as read results. 2.BWx ( NWx) assumed active. - 16 - Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM IEEE 1149.1 TEST ACCESS PORT AND BOUNDARY SCAN-JTAG This part contains an IEEE standard 1149.1 Compatible Test Access Port (TAP). The package pads are monitored by the Serial Scan circuitry when in test mode. This is to support connectivity testing during manufacturing and system diagnostics. Internal data is not driven out of the SRAM under JTAG control. In conformance with IEEE 1149.1, the SRAM contains a TAP controller, Instruction Register, Bypass Register and ID register. The TAP controller has a standard 16-state machine that resets internally upon power-up, therefore, TRST signal is not required. It is possible to use this device without utilizing the TAP. To disable the TAP controller without interfacing with normal operation of the SRAM, TCK must be tied to VSS to preclude mid level input. TMS and TDI are designed so an undriven input will produce a response identical to the application of a logic 1, and may be left unconnected. But they may also be tied to VDD through a resistor. TDO should be left unconnected. JTAG Block Diagram JTAG Instruction Coding IR2 IR1 IR0 Instruction TDO Output Notes Boundary Scan Register 1 IDCODE Identification Register 3 SAMPLE-Z Boundary Scan Register 2 0 0 0 EXTEST 0 0 1 0 1 0 A,D 0 1 1 RESERVED Do Not Use 6 K,K 1 0 0 SAMPLE Boundary Scan Register 5 1 0 1 RESERVED Do Not Use 6 1 1 0 RESERVED Do Not Use 6 1 1 1 BYPASS Bypass Register 4 C,C SRAM CORE Q CQ CQ TDI BYPASS Reg. TDO Identification Reg. Instruction Reg. Control Signals TMS TCK TAP Controller NOTE: 1. Places DQs in Hi-Z in order to sample all input data regardless of other SRAM inputs. This instruction is not IEEE 1149.1 compliant. 2. Places DQs in Hi-Z in order to sample all input data regardless of other SRAM inputs. 3. TDI is sampled as an input to the first ID register to allow for the serial shift of the external TDI data. 4. Bypass register is initiated to VSS when BYPASS instruction is invoked. The Bypass Register also holds serially loaded TDI when exiting the Shift DR states. 5. SAMPLE instruction dose not places DQs in Hi-Z. 6. This instruction is reserved for future use. TAP Controller State Diagram 1 Test Logic Reset 0 0 Run Test Idle 1 1 1 Select DR 0 1 Capture DR 0 Shift DR 1 Exit2 DR 1 Update DR 0 - 17 - Select IR 0 1 Capture IR 0 0 1 Exit1 DR 0 Pause DR 1 1 1 0 0 Shift IR 1 0 Exit1 IR 0 Pause IR 1 Exit2 IR 1 Update IR 1 0 0 0 Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM SCAN REGISTER DEFINITION Part Instruction Register Bypass Register ID Register Boundary Scan 1Mx36 3 bits 1 bit 32 bits 109 bits 2Mx18 3 bits 1 bit 32 bits 109 bits 4Mx9 3 bits 1 bit 32 bits 109 bits ID REGISTER DEFINITION Part Revision Number (31:29) Part Configuration (28:12) Samsung JEDEC Code (11: 1) Start Bit(0) 1Mx36 000 00def0wx0t0q0b0s0 00011001110 1 2Mx18 000 00def0wx0t0q0b0s0 00011001110 1 4Mx9 000 00def0wx0t0q0b0s0 00011001110 1 Note : Part Configuration /def=010 for 36Mb, /wx=11 for x36, 10 for x18 and 00 for x9 /t=1 for DLL Ver., 0 for non-DLL Ver. /q=1 for QDR, 0 for DDR /b=1 for 4Bit Burst, 0 for 2Bit Burst /s=1 for Separate I/O, 0 for Common I/O BOUNDARY SCAN EXIT ORDER ORDER PIN ID ORDER PIN ID 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 6R 6P 6N 7P 7N 7R 8R 8P 9R 11P 10P 10N 9P 10M 11N 9M 9N 11L 11M 9L 10L 11K 10K 9J 9K 10J 11J 11H 10G 9G 11F 11G 9F 10F 11E 10E 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 10D 9E 10C 11D 9C 9D 11B 11C 9B 10B 11A 10A 9A 8B 7C 6C 8A 7A 7B 6B 6A 5B 5A 4A 5C 4B 3A 2A 1A 2B 3B 1C 1B 3D 3C 1D Note: 1. NC pins are read as "X" (i.e. don′t care.) - 18 - ORDER 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 PIN ID 2C 3E 2D 2E 1E 2F 3F 1G 1F 3G 2G 1H 1J 2J 3K 3J 2K 1K 2L 3L 1M 1L 3N 3M 1N 2M 3P 2N 2P 1P 3R 4R 4P 5P 5N 5R Internal Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM JTAG DC OPERATING CONDITIONS Parameter Symbol Min Typ Max Unit Power Supply Voltage VDD 1.7 1.8 1.9 V Input High Level VIH 1.3 - VDD+0.3 V Input Low Level VIL -0.3 - 0.5 V Output High Voltage(IOH=-2mA) VOH 1.4 - VDD V Output Low Voltage(IOL=2mA) VOL VSS - 0.4 V Note Note: 1. The input level of SRAM pin is to follow the SRAM DC specification. JTAG AC TEST CONDITIONS Parameter Symbol Min Unit Input High/Low Level VIH/VIL 1.8/0.0 V Input Rise/Fall Time TR/TF 1.0/1.0 ns 0.9 V Input and Output Timing Reference Level Note 1 Note: 1. See SRAM AC test output load on page 11. JTAG AC Characteristics Parameter Symbol Min Max Unit TCK Cycle Time tCHCH 50 - ns TCK High Pulse Width tCHCL 20 - ns TCK Low Pulse Width tCLCH 20 - ns TMS Input Setup Time tMVCH 5 - ns TMS Input Hold Time tCHMX 5 - ns TDI Input Setup Time tDVCH 5 - ns TDI Input Hold Time tCHDX 5 - ns SRAM Input Setup Time tSVCH 5 - ns SRAM Input Hold Time tCHSX 5 - ns Clock Low to Output Valid tCLQV 0 10 ns Note JTAG TIMING DIAGRAM TCK tCHCH tCHCL tMVCH tCHMX tDVCH tCHDX tSVCH tCHSX tCLCH TMS TDI PI (SRAM) tCLQV TDO - 19 - Rev. 1.1 August 2006 K7R323684C K7R321884C K7R320984C 1Mx36, 2Mx18 & 4Mx9 QDRTM II b4 SRAM 165 FBGA PACKAGE DIMENSIONS (Lead & Lead-Free) 15mm x 17mm Body, 1.0mm Bump Pitch, 11x15 Ball Array B Top View A Side View C D A G E B F Bottom View ∅H E Symbol Value Units Symbol Value Units A 15 ± 0.1 mm Note E 1.0 mm B 17 ± 0.1 mm F 14.0 mm C 1.3 ± 0.1 mm G 10.0 mm D 0.35 ± 0.05 mm H 0.5 ± 0.05 mm - 20 - Note Rev. 1.1 August 2006