VC-801 CMOS Crystal Oscillator Previous Vectron Model VCC4 VC-801 Description Vectron’s VC-801 Crystal Oscillator (XO) is a quartz stabilized square wave generator with a CMOS output. The VC-801 uses fundamental or 3rd overtone crystals resulting in very low jitter performance, and a monolithic IC which improves reliability and reduces cost. Features Applications • • • • • • • • CMOS output XO Output Frequencies from 32.768kHz to 125.000MHz 5.0, 3.3, 2.5 or 1.8 V Operation Low Jitter Performance Output Disable Feature Excellent 20ppm temperature stability -10/70°C, -20/70°C, -40/85°C or -55/125°C operating temperature Small Industry Standard Package, 3.2x5.0x1.3mm • Product is compliant to RoHS directive and fully compatible with lead free assembly • • • • • • • SONET/SDH/DWDM Ethernet, GE, SynchE Storage Area Networking Fiber Channel Digital Video Broadband Access Base Stations, Picocells Block Diagram Output VDD Crystal Oscillator GND E/D Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page1 Specifications Performance Specifications Table 1. Electrical Performance, 5V Option Parameter Symbol Min Typical Maximum Units 5.0 5.5 V 7 V 10 30 40 mA mA mA 30 uA Supply Voltage1 VDD 4.5 Max Voltage -0.7 Current2 ≤20.000MHz 20.001 to 50.000MHz 50.001 to 75.000MHz IDD Current, Output Disabled Frequency 3 Nominal Frequency fN 1.544 Stability4, (Ordering Option) 75.000 MHz ±20, ±25, ±32, ±50, ±100 ppm Outputs 2 Output Logic Levels Output Logic High Output Logic Low Output Logic High Drive Output Logic Low Drive VOH VOL IOH IOL Load IOUT 2 0.9*VDD V V mA mA 15 pF 8 5 2 ns ns ns ±10 uA 55 % 16 16 tR/tF Output Rise /Fall Time <20.000MHz 20.000 to 50.000MHz 50.001 to 75.000MHz Output Leakage, Output Disabled IZ Duty Cycle2,5 Period Jitter RMS Peak-Peak 0.1*VDD 45 6 50 фJ 3.0 21 RMS Jitter, 12kHz-20MHz фJ ps ps 0.5 1 ps 0.8 V V Enable/Disable Output Enable/Disable Output Enable Output Disable 7 VIH VIL Disable time 4.0 100 tD Enable Internal Pull-Up Resistor 1] 2] 3] 4] 5] 6] 7] Start-Up Time tSU Operating Temp, (Ordering Option) TOP Kohm 8 °C The power supply should have by-pass capacitors as close to the supply and to ground as possible, for example 0.1 and 0.01uF. Parameters are tested a test circuit shown in Figure 1. See Standard Frequencies and Ordering Information tables for more specific information. Includes initial accuracy, operating temperature, supply voltage, shock and vibration (not under operation) and aging for 50 and 100ppm options. Duty Cycle is measured as On Time/Period, see Fig 2. Broadband Period Jitter measured using Wavecrest SIA3300C, 90K samples, see Application Note for Typical Phase Noise and Jitter Performance. The Output is Enabled if the Enable/Disable is left open. IDD VDD ms -10/70, -20/70, -40/85, -55/125 tR + ns 100 tF VOH .1μF .01μF 4 3 1 2 50% VOL 15pF On Time + Period Fig 2: Waveform Fig 1: Test Circuit Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page2 Specifications Performance Specifications Table 2. Electrical Performance, 3.3V Option Parameter Symbol Min Typical Maximum Units 3.3 3.63 V 5 V 5 7 20 30 40 mA mA mA mA mA 30 uA 125.000 MHz Supply Voltage1 VDD 2.97 Maximum Voltage -0.5 2 Current 32.768kHz to 1.499MHz 1.500 to 20.000MHz 20.001 to 50.000MHz 50.001 to 100.000MHz 100.001 to 125.000MHz IDD Current, Output Disabled Frequency Nominal Frequency3 fN 0.032768 4 Stability , (Ordering Option) ±20, ±25, ±32, ±50, ±100 ppm Outputs Output Logic Levels2 Output Logic High Output Logic Low Output Logic High Drive Output Logic Low Drive VOH VOL IOH IOL Load IOUT 2 Output Rise /Fall Time 32.768kHz to 345.6kHz 345.6kHz to 20.000MHz 20.001 to 50.000MHz 50.001 to 75.000MHz 75.001 to 125.000MHz Output Leakage, Output Disabled 0.9*VDD Period Jitter RMS Peak-Peak V V mA mA 15 pF 200 6 4 3 2 ns ns ns ns ns ±10 uA 55 % 8 8 tR/tF IZ Duty Cycle2,5 45 6 0.1*VDD 50 фJ 3.0 21 RMS Jitter, 12kHz-20MHz фJ ps ps 0.5 1 ps 0.5 V V Enable/Disable Output Enable/Disable Output Enable Output Disable 7 Disable time VIH VIL 2.0 100 tD Enable Internal Pull-Up Resistor 100 Start-Up Time tSU Operating Temp, (Ordering Option) TOP 1] 2] 3] 4] 5] 6] 7] ns Kohm 8 -10/70, -20/70, -40/85, -55/125 ms °C The power supply should have by-pass capacitors as close to the supply and to ground as possible, for example 0.1 and 0.01uF. Parameters are tested a test circuit shown in Figure 1. See Standard Frequencies and Ordering Information tables for more specific information. Includes initial accuracy, operating temperature, supply voltage, shock and vibration (not under operation) and aging for 50 and 100ppm options. Duty Cycle is measured as On Time/Period, see Fig 2. Broadband Period Jitter measured using Wavecrest SIA3300C, 90K samples, see Application Note for Typical Phase Noise and Jitter Performance. The Output is Enabled if the Enable/Disable is left open. Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page3 Specifications Performance Specifications Table 3. Electrical Performance, 2.5V Option Parameter Symbol Min Typical Maximum Units 2.5 2.75 V 5 V 5 7 15 20 25 30 mA mA mA mA mA mA 30 uA 125.000 MHz Supply Voltage1 VDD Maximum Voltage 2.25 -0.5 2 Current 32.768kHz to 1.499MHz 1.500 to 20.000MHz 20.001 to 50.000MHz 50.001 to 75.000MHz 75.001 to 100.000MHz 100.001 to 125.000MHz IDD Current, Output Disabled Frequency 3 Nominal Frequency fN 0.032768 Stability , (Ordering Option) 4 ±20, ±25, ±32, ±50, ±100 ppm Outputs Output Logic Levels2,3 Output Logic High Output Logic Low Output Logic High Drive Output Logic Low Drive Output Logic High Drive5 Output Logic Low Drive5 VOH VOL IOH IOL IOH IOL Load IOUT 2 Output Rise /Fall Time 32.768kHz to 345.6kHz 345.6kHz to 20.000MHz 20.001 to 50.000MHz 50.001 to 75.000MHz 75.001 to 125.000MHz Output Leakage, Output Disabled Duty Cycle 0.9*VDD 0.1*VDD 4 4 8 8 V V mA mA mA mA 15 pF 200 6 5 3 2 ns ns ns ns ns ±10 uA 55 % tR/tF IZ 2,6 45 Period Jitter7 RMS Peak-Peak фJ RMS Jitter, 12kHz-20MHz фJ 50 3.0 21 ps ps 0.5 1 ps 0.5 V V Enable/Disable Output Enable/Disable Output Enable Output Disable 8 Disable time VIH VIL 1.75 tD ns Enable Internal Pull-Up Resistor 100 Start-Up Time tSU Operating Temp, (Ordering Option) TOP 1] 2] 3] 4] 5] 6] 7] Kohm 8 -10/70, -20/70, -40/85, -55/125 ms °C The power supply should have by-pass capacitors as close to the supply and to ground as possible, for example 0.1 and 0.01uF. Parameters are tested a test circuit shown in Figure 1. See Standard Frequencies and Ordering Information tables for more specific information. Includes initial accuracy, operating temperature, supply voltage, shock and vibration (not under operation) and aging for 50 and 100ppm options. Duty Cycle is measured as On Time/Period, see Fig 2. Broadband Period Jitter measured using Wavecrest SIA3300C, 90K samples, see Application Note for Typical Phase Noise and Jitter Performance. The Output is Enabled if the Enable/Disable is left open. Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page4 Performance Specifications Table 4. Electrical Performance, 1.8V Option Parameter Symbol Min Typical Maximum Units 1.8 1.89 V 3.6 V 5 15 20 25 mA mA mA mA 30 uA 125.000 MHz Supply Voltage1 VDD 1.71 Maximum Voltage -0.5 Current2 ≤20.000MHz 20.001 to 70.000MHz 70.001 to 100.000MHz 100.001 to 125.000MHz IDD Current, Output Disabled Frequency Nominal Frequency3 fN 1.544 4 Stability , (Ordering Option) ±20, ±25, ±32, ±50, ±100 ppm Outputs Output Logic Levels2,3 Output Logic High Output Logic Low Output Logic High Drive Output Logic Low Drive Output Logic High Drive5 Output Logic Low Drive5 VOH VOL IOH IOL IOH IOL Load IOUT 2 Output Rise /Fall Time <20.000MHz 20.000 to 50.000MHz 50.001 to 125.000MHz Output Leakage, Output Disabled Duty Cycle 0.9*VDD 0.1*VDD 2.8 2.8 8 8 V V mA mA mA mA 15 pF 6 5 3 ns ns ns ±10 uA 55 % tR/tF IZ 2,6 45 Period Jitter7 RMS Peak-Peak фJ RMS Jitter, 12kHz-20MHz фJ 50 3.0 21 ps ps 0.5 1 ps 0.5 V V 100 ns Enable/Disable Output Enable/Disable8 Output Enable Output Disable VIH VIL Disable time tD 1.26 Enable Internal Pull-Up Resistor 1 Start-Up Time tSU Operating Temp, Ordering Option TOP 1] 2] 3] 4] 5] 6] 7] Mohm 8 -10/70, -20/70, -40/85, -55/125 ms °C The power supply should have by-pass capacitors as close to the supply and to ground as possible, for example 0.1 and 0.01uF. Parameters are tested a test circuit shown in Figure 1. See Standard Frequencies and Ordering Information tables for more specific information. Includes initial accuracy, operating temperature, supply voltage, shock and vibration (not under operation) and aging for 50 and 100ppm options. Duty Cycle is measured as On Time/Period, see Fig 2. Broadband Period Jitter measured using Wavecrest SIA3300C, 90K samples, see Application Note for Typical Phase Noise and Jitter Performance. The Output is Enabled if the Enable/Disable is left open. Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page5 Outline Drawing & Pad Layout 2.54 1.2 2.2 1.3 max 1.4 Dimensions in mm Table 5. Pin Out Pin Symbol Function 1 E/D Enable Disable 2 GND Case and Electrical Ground 3 Output Output 4 VDD Power Supply Voltage Reliability VI qualification includes aging at various extreme temperatures, shock and vibration, temperature cycling, and IR reflow simulation. The VC-801 family is capable of meeting the following qualification tests: Table 6. Environmental Compliance Parameter Conditions Mechanical Shock MIL-STD-883, Method 2002 Mechanical Vibration MIL-STD-883, Method 2007 Solderability MIL-STD-883, Method 2003 Gross and Fine Leak MIL-STD-883, Method 1014 Resistance to Solvents MIL-STD-883, Method 2015 Moisture Sensitivity Level MSL 1 Contact Pads Gold over Nickel Typical Characteristics - Phase Noise and Gain Curve Although ESD protection circuitry has been designed into the VC-801 proper precautions should be taken when handling and mounting. VI employs a human body model (HBM) and a charged device model (CDM) for ESD susceptibility testing and design protection evaluation. Table 7. ESD Ratings Model Minimum Conditions Human Body Model 1500V MIL-STD-883, Method 3015 Charged Device Model 1000V JESD22-C101 Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this datasheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Permanent damage is also possible if E/D is applied before VDD. Table 8. Absolute Maximum Ratings Parameter Symbol Ratings Unit Storage Temperature TS -55 to 125 °C Soldering Temp/Time TLS 260 / 30 °C / sec Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page6 IR Reflow The VC-801 is qualified to meet the JEDEC standard for Pb-Free assembly. The temperatures and time intervals listed are based on the Pb-Free small body requirements. The VC-801 device is hermetically sealed so an aqueous wash is not an issue. Table 9. Reflow Profile Parameter Symbol Value PreHeat Time Ts-min Ts-max tS 60 sec Min, 260 sec Max 150°C 200°C Ramp Up RUP 3 °C/sec Max Time Above 217 °C tL 60 sec Min, 150 sec Max Time To Peak Temperature TAMB-P 480 sec Max Time at 260 °C tP 30 sec Max Ramp Down RDN 6 °C/sec Max Tape and Reel Table 10 . Tape and Reel Dimensions Tape Dimensions (mm) Reel Dimensions (mm) Dimension W F Do Po P1 A B C D N W1 W2 Tolerance Typ Typ Typ Typ Typ Typ Min Typ Min Min Typ Max # Per Reel VC-801 16 7.5 1.5 4 8 180 2 13 21 60 17 21 1000 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page7 Table 11. Standard Output Frequencies (MHz) 9.8304 10.000 11.0590 11.0596 11.2896 12.000 12.272 12.288 12.353 13.000 13.500 13.560 14.318 14.7456 16.000 16.376 16.384 16.777216 16.800 17.734 17.734475 18.432 19.440 19.660 19.800 20.000 20.480 22.000 22.5792 24.000 24.5453 24.576 25.000 26.000 27.000 27,120 28.686 28.375 30.000 32.000 32.768 33.000 33.333 34.368 36.000 37.056 47.500 40.000 42.500 44.000 44.736 48.000 48.090 50.000 54.000 60.000 62.500 66.000 66.666 75.000 80.000 100.000 125.000 Ordering Information VC-801- E A W- K A A N- xxMxxxxxxx Frequency M for MHz or K for kHz Product Crystal Oscillator Package 3.2x5 Ceramic Custom Options N: Standard Option Load A: 15pF B: 30pF C: 50pF (5V option only) Power Supply D: +5.0Vdc E: +3.3Vdc H: +2.5Vdc J: +1.8Vdc Output A: CMOS Temp Range W: -10/70°C *Note: not all combination of options are available. Other specifications may be available upon request. J: -20/70°C E: -40/85°C C: -55/125°C (±50 and ±100ppm) Enable/Disable A: Enable/Disable, Enable High Stability E: ±20ppm F: ±25ppm H: ±32ppm K: ±50ppm S: ±100ppm Example: VC-801-EAW-KAAN-125M000000 USA: Vectron International 267 Lowell Road Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 For Additional Information, Please Contact Europe: Asia: Vectron International Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 3328.4784.17 Fax: +49 (0) 3328.4784.30 VI Shanghai 1589 Century Avenue, the 19th Floor Chamtime International Financial Center Shanghai, China Tel: 86.21.6081.2888 Fax: 86.21.6163.3598 Disclaimer Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Rev: 09/24/2010 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page8