FREESCALE AN1984

Freescale Semiconductor
Application Note
AN1984
Rev 3, 11/2006
Handling Freescale Pressure Sensors
by: William McDonald
INTRODUCTION
Smaller package outlines and higher board densities
require the need for automated placement of components.
These components are supplied in embossed carrier tape on
plastic reels to meet the increased demand and facilitate ease
of handling. This application note is intended to provide
general information and understanding for handling
Freescale’s surface mount pressure sensors. Equipment
details are not provided in this document and it is
recommended that end users contact suppliers of equipment
for specific applications.
METHODS OF HANDLING
Components can be picked from the carrier tape using
either the vacuum assist or the mechanical type pick up
heads. A vacuum assist nozzle type is most common due to
its lower cost of maintenance and ease of operation. The
recommended vacuum nozzle configuration should be
designed to make contact with the device directly on the metal
Figure 1. MPXH Series Multiple Port
Vacuum Nozzles
cover and avoid vacuum port location directly over the vent
hole in the metal cover of the device. To provide a more secure
hold on the device, contact with the plastic ridge around the
perimeter of the metal cover should be avoided to prevent loss
of vacuum pressure. Multiple vacuum ports within the nozzle
may be required to effectively handle the device and prevent
shifting during movement to placement position.
Figure 1 shows two styles of multiple port vacuum nozzles
for the MPXH series device as an example. Figure 2
represents the nozzle location on the device.
Vacuum pressure required to adequately support the
component should be approximately 25 in Hg (85kPa). This
level is typical of in-house vacuum supply.
Pick up nozzles are available in various sizes and
configurations to suit a variety of component geometries. To
select the nozzle best suited for the specific application, it is
recommended that the customer consult their pick and place
equipment supplier to determine the correct nozzle. In some
cases it may be necessary to fabricate a special nozzle
depending on the equipment and speed of operation.
Figure 2. Nozzle Location
AVAILABLE PACKAGES
Freescale offers several small outline surface mount device
families. These are MPXA, MPXH, MPXM, and MPXY series
of devices.
These devices are also available in axial ported versions to
allow pressure to be interfaced to a device via a hose
connection.
© Freescale Semiconductor, Inc., 2006. All rights reserved.
Figure 3. SSOP Axial Style Port
Pick up nozzles for these packages should be configured to
apply vacuum only to the flat surface of a port base. An access
clearance in the nozzle for a port shank is necessary to
properly handle these device configurations. See Figure 3.
SOP
MPAK
SSOP
SOIC16
Figure 2. Available Packages
Table 1. Tape and Reel Information
Case
Carrier Tape
423A
1317
1317A
1320
1320A
482
482A
1369
Chip Pak
SSOP
SSOP
Ported
M-Pak
M-Pak
Ported
SOP
SOP Ported
SOP
Side Port
Tape Width
W
24.0+/-0.3
24.0+/-0.3
24.0+/-0.3
24.0+/-0.3
24.0+/-0.3
32+/-0.3
32+/-0.3
32+/-0.3
Pocket Width
Ao
8.5+/-0.2
7.7+/-0.1
8.8+/-0.1
6.8+/-0.1
7.2+/-0.1
11.3+/-0.1
12.0+/-0.2
12.6+/-0.2
Length
Bo
14.2+/-0.2
10.7+/-0.1
11.8+/-0.1
12.6+/-0.1
13.2+/-0.1
18.9+/-0.1
18.8+/-0.2
18.8+/-0.2
Depth
Ko
4.7+/-0.1
5.0+/-0.1
10.8+/-0.1
4.6+/-0.1
10.5+/-0.1
6.4+/-0.1
13.8+/-0.1
9.2+/-0.2
Sprocket Hole
Pitch
Po
4.0 +/-0.1
4.0+/-0.1
4.0+/-0.1
4.0+/-0.1
4.0+/-0.1
4.0+/-0.1
4.0+/-0.1
4.0+/-0.1
Sprocket Hole
Diagram
Do
1.55+/-0.05
1.55+/-0.05
1.55+/-0.05
1.55+/-0.05
1.55+/-0.05
1.5+/-0.05
1.5+/-0.1
1.5+/-0.1
Edge to Hole
E1
1.75+/-0.1
1.75+/-0.1
1.75+/-0.1
1.75+/-0.1
1.75+/-0.1
1.75+/-0.1
1.75+/-0.1
1.75+/-0.1
Hole to Edge
E2
22.2 min
22.2 min
22.2 min
22.2 min
22.2 min
N/A
N/A
N/A
Distance
between Holes
So
N/A
N/A
N/A
N/A
N/A
28.4+/-0.1
28.4+/-0.1
28.4+/-0.1
Pocket Pitch
P1
12.0+/-0.1
12.0+/-0.1
16.0+/-0.1
12.0+/-0.1
16.0+/-0.1
16.0+/-0.1
20.0+/-0.1
24.0+/-.01
Pocket
Position
P2
2.0+/-0.1
2.0+/-0.1
2.0+/-0.1
2.0+/-0.1
2.0+/-0.1
2.0+/-0.1
2.0+/-0.1
2.0+/-0.1
F
11.5+/-0.1
11.5+/-0.1
11.5+/-0.1
11.5+/-0.1
11.5+/-0.1
14.2+/-0.1
14.2+/-0.1
14.2+/-0.1
Tape
Thickness
T
0.40+/-0.05
0.40+/-0.05
0.40+/-0.05
0.40+/-0.05
0.40+/-0.05
0.30+/-0.05
0.35+/-0.05
0.40+/-0.05
Distance
Pocket to
Edge
S1
0.6 min.
0.6 min
0.6 min
0.6 min
0.6 min
N/A
N/A
N/A
Pocket Hole
Diagram
D1
N/A
1.5+/-0.1
1.5+/-0.1
1.5+/-0.1
1.5+/-0.1
2.0+/-0.1
2.0+/-0.1
2.0+/-0.1
Thickness
T1
0.052
+/-0.01
0.052
+/-0.01
0.052
+/-0.01
0.052
+/-0.01
0.052
+/-0.01
0.052
+/-0.01
0.052
+/-0.01
0.052
+/-0.01
Width
W4
21.1+/-0.1
21.1+/-0.1
21.1+/-0.1
21.1+/-0.1
21.1+/-0.1
21.1+/-0.1
25.5+/-0.1
25.5+/-0.1
Width at Hub
W1
23.7 - 25.2
23.7 - 25.2
23.7 - 25.2
23.7 - 25.2
23.7 - 25.2
23.7 - 25.2
31.7 - 33.2
31.7 - 33.2
Width at outer
flange
W3
23.7 - 28.0
23.7 - 28.0
23.7 - 28.0
23.7 - 28.0
23.7 - 28.0
23.7 - 28.0
31.7 - 36.0
31.7 - 36.0
Cover Tape
Reel
Overall Width
W2
30.4 max.
30.4 max.
30.4 max.
30.4 max.
30.4 max.
30.4 max.
38.4 max.
38.4 max
Hub Diagram
N
100+/-2.50
100+/-2.50
100+/-2.50
100+/-2.50
100+/-2.50
100+/-2.50
178+/-2.50
178+/-2.50
Arbor Hole
Diagram
C
13.0+
0.5/-0.2
13.0+
0.5/-0.2
13.0+
0.5/-0.2
13.0
+0.5/-0.2
13.0
+0.5/-0.2
13.0
+0.5/-0.2
13.0
+0.5/-0.2
13.0
+0.5/-0.2
Slot of Arbor
Hole
B
1.50/2.50
1.50/2.50
1.50/2.50
1.50/2.50
1.50/2.50
1.50/2.50
1.50/2.50
1.50/2.50
A
330+/-0.76
330+/-0.76
330+/-0.76
330+/-0.76
330+/-0.76
330+/-0.76
330+/-0.76
330+/-0.76
MPQ
1000
1000
300
1000
400
600
100
200
Reel Diagram
DEVICE
QTY/REEL
AN1984
2
Sensors
Freescale Semiconductor
Cover
Tape
Carrier
Tape
D0
T
P2
D1
P0
B
E1
F
E2
B0
W4
A0
S1
P1
T1
W
B
K0
A0
m
0.2
0+/-
B0
K1
Hole Location
View A-A
View B-B
Figure 3. Carrier Tape
Plastic Reel
W3
W2
A
N
D*
C
B*
W1
Front View
Side View
Reel
Sealing Tape
Pocket
Carrier Tape
Bar Code Label
Figure 4. Reel
AN1984
Sensors
Freescale Semiconductor
3
Pin 1
Pin 1
Corner
Chamfer
User Direction of Feed
Figure 5. Orientation of Small Outline Package Sensor Device
AN1984
4
Sensors
Freescale Semiconductor
PACKAGE DIMENSIONS
-A-
D 8 PL
0.25 (0.010)
4
5
M
T B
A
S
S
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006).
5. ALL VERTICAL SURFACES 5˚ TYPICAL DRAFT.
-BG
8
1
S
N
H
C
J
-TSEATING
PLANE
PIN 1 IDENTIFIER
K
M
DIM
A
B
C
D
G
H
J
K
M
N
S
INCHES
MIN
MAX
0.415 0.425
0.415 0.425
0.212 0.230
0.038 0.042
0.100 BSC
0.002 0.010
0.009 0.011
0.061 0.071
0˚
7˚
0.405 0.415
0.709 0.725
MILLIMETERS
MIN
MAX
10.54 10.79
10.54 10.79
5.38
5.84
0.96
1.07
2.54 BSC
0.05
0.25
0.23
0.28
1.55
1.80
0˚
7˚
10.29 10.54
18.01 18.41
SOP PACKAGE
CASE
482-01
CASE
482-01
ISSUE
OO
ISSUE
DATE 01/27/98
-A-
D
4
0.25 (0.010)
5
N
8 PL
M
T B
S
A
S
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006).
5. ALL VERTICAL SURFACES 5˚ TYPICAL DRAFT.
-BG
8
1
S
W
V
C
H
J
-TK
M
PIN 1 IDENTIFIER
SOP PACKAGE
CASE 482A-01
CASE
482A-01
ISSUE
A
ISSUE A
DIM
A
B
C
D
G
H
J
K
M
N
S
V
W
INCHES
MIN
MAX
0.415 0.425
0.415 0.425
0.500 0.520
0.038 0.042
0.100 BSC
0.002 0.010
0.009 0.011
0.061 0.071
0˚
7˚
0.444 0.448
0.709 0.725
0.245 0.255
0.115 0.125
MILLIMETERS
MIN
MAX
10.54
10.79
10.54
10.79
12.70
13.21
0.96
1.07
2.54 BSC
0.05
0.25
0.23
0.28
1.55
1.80
0˚
7˚
11.28
11.38
18.01
18.41
6.22
6.48
2.92
3.17
SEATING
PLANE
DATE 05/13/98
AN1984
Sensors
Freescale Semiconductor
5
PACKAGE DIMENSIONS
PAGE 1 OF 2
MPAK PACKAGE
CASE 1320-02
ISSUE B
AN1984
6
Sensors
Freescale Semiconductor
PACKAGE DIMENSIONS
PAGE 2 OF 2
MPAK PACKAGE
CASE 1320-02
ISSUE B
AN1984
Sensors
Freescale Semiconductor
7
PACKAGE DIMENSIONS
PAGE 1 OF 2
MPAK PACKAGE
CASE 1320A-02
ISSUE A
AN1984
8
Sensors
Freescale Semiconductor
PACKAGE DIMENSIONS
PAGE 2 OF 2
MPAK PACKAGE
CASE 1320A-02
ISSUE A
AN1984
Sensors
Freescale Semiconductor
9
PACKAGE DIMENSIONS
PAGE 1 OF 2
SSOP PACKAGE
CASE 1317A-03
ISSUE C
AN1984
10
Sensors
Freescale Semiconductor
PACKAGE DIMENSIONS
PAGE 2 OF 2
SSOP PACKAGE
CASE 1317A-03
ISSUE C
AN1984
Sensors
Freescale Semiconductor
11
PACKAGE DIMENSIONS
PAGE 1 OF 3
SSOP PACKAGE
CASE 1317-04
ISSUE F
AN1984
12
Sensors
Freescale Semiconductor
PACKAGE DIMENSIONS
PAGE 2 OF 3
SSOP PACKAGE
CASE 1317-04
ISSUE F
AN1984
Sensors
Freescale Semiconductor
13
PACKAGE DIMENSIONS
PAGE 3 OF 3
SSOP PACKAGE
CASE 1317-04
ISSUE F
AN1984
14
Sensors
Freescale Semiconductor
PACKAGE DIMENSIONS
PAGE 1 OF 3
SSOP PACKAGE
CASE 1352-03
ISSUE C
AN1984
Sensors
Freescale Semiconductor
15
PACKAGE DIMENSIONS
PAGE 2 OF 3
SSOP PACKAGE
CASE 1352-03
ISSUE C
AN1984
16
Sensors
Freescale Semiconductor
PACKAGE DIMENSIONS
PAGE 3 OF 3
SSOP PACKAGE
CASE 1352-03
ISSUE C
AN1984
Sensors
Freescale Semiconductor
17
How to Reach Us:
Home Page:
www.freescale.com
Web Support:
http://www.freescale.com/support
USA/Europe or Locations Not Listed:
Freescale Semiconductor, Inc.
Technical Information Center, EL516
2100 East Elliot Road
Tempe, Arizona 85284
+1-800-521-6274 or +1-480-768-2130
www.freescale.com/support
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
[email protected]
AN1984
Rev. 3
11/2006
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc. 2006. All rights reserved.