LTC2978 Octal PMBus Power Supply Monitor and Controller with EEPROM Description Features n n n n n n n n n n n n n PMBus Compliant Interface and Command Set Configuration EEPROM Fault Logging to Internal EEPROM Differential Input, 15-Bit ∆Σ ADC with Less Than ±0.25% of Total Unadjusted Error Monitors Eight Output Channels and One Input Voltage 8-Channel Sequencer Programmable Watchdog Timer Eight UV/OV Voltage Supervisors Eight 10-Bit Voltage-Buffered IDACs with Soft Connect Linear, Voltage Servo Adjusts Supply Voltages by Ramping Voltage-Buffered IDAC Outputs Up/Down Supports Multichannel Fault Management On-Chip Digital Temperature Sensor Available in 64-Pin 9mm × 9mm QFN Package The LTC®2978 is an octal, PMBus compliant power supply monitor, supervisor, sequencer and margin controller. PMBus functions include warning and fault OV/UV threshold pairs for eight output channels and one input channel. Programmable fault response allows the power supplies to be disabled with optional retry after a fault has been detected. PMBus reads allow eight output voltages and one input voltage to be monitored. In addition, odd numbered channels can substitute sense resistor voltage measurements for output voltage measurements. PMBus commands support power supply sequencing and precision point-of-load voltage servo to one of three programmed values: margin high, margin low and nominal. A programmable watchdog timer monitors microprocessor activity for a stalled condition and resets the micro if necessary. The 1-wire synchronization bus supports power supply sequencing across multiple LTC2978 devices. User programmable parameters can be stored in EEPROM. Voltage supervisor, voltage monitor and temperature faults can also be logged to EEPROM. Applications Computers Network Servers n L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 7382203 and 7420359. n Typical Application Octal Power Supply Controller with PMBus Interface VIN 4.5V < VIBUS < 15V TO INTERMEDIATE BUS CONVERTER ENABLE VPWR VIN_SNS VIN_EN VDACP0 VSENSEP0 SDA PMBus INTERFACE WRITE-PROTECT LTC2978* SCL ALERTB VSENSEM0 CONTROL0 VOUT_EN0 WP PWRGD FAULTB00 ASEL0 SHARE_CLK R20 7.5k LOAD VDACM0 WDI/RESETB TO/FROM OTHER LTC2978s VOUT R30 41.2k R10 20k DIGITALLY MANAGED POWER SUPPLY VFB SGND RUN/SS GND TO µP RESETB INPUT WATCHDOG TIMER INTERRUPT ASEL1 GND 2978 TA01 *SOME DETAILS OMITTED FOR CLARITY ONLY ONE OF EIGHT CHANNELS SHOWN 2978fa LTC2978 Table of Contents Features..............................................................................................................................1 Applications.........................................................................................................................1 Typical Application.................................................................................................................1 Description..........................................................................................................................1 Absolute Maximum Ratings.......................................................................................................3 Order Information...................................................................................................................3 Pin Configuration...................................................................................................................3 Electrical Characteristics..........................................................................................................4 Timing Diagram.....................................................................................................................8 Typical Performance Characteristics............................................................................................8 Pin Functions...................................................................................................................... 12 Block Diagram..................................................................................................................... 14 Operation.......................................................................................................................... 15 Operation Overview................................................................................................................................................15 PMBus Serial Digital Interface................................................................................................................................16 Register Command Set...........................................................................................................................................18 Detailed PMBus Command Register Descriptions..................................................................................................22 Manufacturer Specific Commands..........................................................................................................................35 Watchdog...............................................................................................................................................................49 Reset......................................................................................................................................................................49 Write-Protect Pin....................................................................................................................................................49 Other Operations.....................................................................................................................................................49 Applications Information........................................................................................................ 50 PCB Assembly and Layout Suggestions.................................................................................................................61 Typical Application............................................................................................................... 62 Package Description............................................................................................................. 63 Typical Application............................................................................................................... 64 Related Parts...................................................................................................................... 64 2978fa LTC2978 Supply Voltages: VPWR to GND.......................................... –0.3V to 15V VIN_SNS to GND...................................... –0.3V to 15V VDD33 to GND........................................ –0.3V to 3.6V VDD25 to GND...................................... –0.3V to 2.75V Digital Input/Output Voltages: ALERTB, SDA, SCL, CONTROL0, CONTROL1............................................. –0.3V to 5.5V PWRGD, SHARE_CLK, WDI, WP...................................–0.3V to VDD33 + 0.3V FAULTB00, FAULTB01, FAULTB10, FAULTB11.................................–0.3V to VDD33 + 0.3V ASEL0, ASEL1...........................–0.3V to VDD33 + 0.3V Analog Voltages: REFP.................................................... –0.3V to 1.35V REFM to GND......................................... –0.3V to 0.3V VSENSEP[7:0] to GND.................................. –0.3V to 6V VSENSEM[7:0] to GND................................. –0.3V to 6V VOUT_EN[3:0], VIN_EN to GND................... –0.3V to 15V VOUT_EN[7:4] to GND.................................. –0.3V to 6V VDACP[7:0] to GND..................................... –0.3V to 6V VDACM[7:0] to GND ................................ –0.3V to 0.3V Operating Temperature Range: LTC2978C................................................. 0°C to 70°C LTC2978I..............................................–40°C to 85°C Storage Temperature Range................... –65°C to 125°C Pin Configuration TOP VIEW 64 VSENSEP6 63 VSENSEM5 62 VSENSEP5 61 VDACM7 60 VDACP7 59 VDACP6 58 VDACM6 57 VDACM5 56 VDACP5 55 VDACP4 54 VDACM4 53 VSENSEM4 52 VSENSEP4 51 VDACM3 50 VDACP3 49 VSENSEM3 (Notes 1, 2) VSENSEM6 1 VSENSEP7 2 VSENSEM7 3 VOUT_EN0 4 VOUT_EN1 5 VOUT_EN2 6 VOUT_EN3 7 VOUT_EN4 8 VOUT_EN5 9 VOUT_EN6 10 VOUT_EN7 11 VIN_EN 12 DNC 13 VIN_SNS 14 VPWR 15 VDD33 16 48 VSENSEP3 47 VSENSEM2 46 VSENSEP2 45 VDACM2 44 VDACP2 43 VSENSEM1 42 VSENSEP1 41 VDACM1 40 VDACP1 39 VDACP0 38 VDACM0 37 VSENSEM0 36 VSENSEP0 35 REFM 34 REFP 33 ASEL1 65 VDD33 17 VDD25 18 WP 19 PWRGD 20 SHARE_CLK 21 WDI/RESET 22 FAULTB00 23 FAULTB01 24 FAULTB10 25 FAULTB11 26 SDA 27 SCL 28 ALERTB 29 CONTROL0 30 CONTROL1 31 ASEL0 32 Absolute Maximum Ratings UP PACKAGE 64-LEAD (9mm s 9mm) PLASTIC QFN TJMAX = 125°C, θJA = 28°C/W EXPOSED PAD (PIN 65) IS GND, MUST BE SOLDERED TO PCB Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC2978CUP#PBF LTC2978CUP#TRPBF LTC2978 64-Lead (9mm × 9mm) Plastic QFN 0°C to 70°C LTC2978IUP#PBF LTC2978IUP#TRPBF LTC2978 64-Lead (9mm × 9mm) Plastic QFN –40°C to 85°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 2978fa LTC2978 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VPWR = VIN_SNS = 12V, VDD33, VDD25 and REF pins floating, unless otherwise indicated. CVDD33 = 100nF, CVDD25 = 100nF and CREF = 100nF. SYMBOL PARAMETER Power-Supply Characteristics VPWR VPWR Supply Input Operating Range IPWR VPWR Supply Current IVDD33 VDD33 Supply Current VUVLO_VDD33 VDD33 Undervoltage Lockout VDD33 Undervoltage Lockout Hysteresis VDD33 Supply Input Operating Range Regulator Output Voltage Regulator Output Short-Circuit Current VDD25 Regulator Output Voltage Regulator Output Short-Circuit Current Voltage Reference Characteristics VREF Output Voltage Temperature Coefficient Hysteresis ADC Characteristics VIN_ADC Voltage Sense Input Range N_ADC Current Sense Input Range (Odd Numbered Channels Only When So Configured) Voltage Sense Resolution Current Sense Resolution (Odd Numbered Channels Only When So Configured) TUE_ADC INL_ADC Total Unadjusted Error Integral Nonlinearity DNL_ADC VOS_ADC GAIN_ADC Differential Nonlinearity Offset Error Gain Error tCONV_ADC Conversion Time CIN_ADC fIN_ADC Input Sampling Capacitance Input Sampling Frequency CONDITIONS MIN l 4.5 4.5V ≤ VPWR ≤ 15V, VDD33 Floating 3.13V ≤ VDD33 ≤ 3.47V, VPWR = VDD33 VDD33 Ramping Up, VPWR = VDD33 l l 2.35 VPWR = VDD33 4.5V ≤ VPWR ≤ 15V VPWR = 4.5V, VDD33 = 0V 3.13V ≤ VDD33 ≤ 3.47V VPWR = VDD33 = 3.47V, VDD25 = 0V l 3.13 3.13 75 2.35 30 l l l l l 0V ≤ VIN_ADC ≤ 6V 0mV ≤ |VIN_ADC| < 16mV 16mV ≤ |VIN_ADC| < 32mV 32mV ≤ |VIN_ADC| < 63.9mV 63.9mV ≤ |VIN_ADC| < 127.9mV 127.9mV ≤ |VIN_ADC| VIN_ADC ≥ 1.8V (Note 4 ) Voltage Sense Mode (Note 5) Current Sense Mode, Odd Numbered Channels Only, 15.6µV/LSB (Note 5) Voltage Sense Mode Current Sense Mode, Odd Numbered Channels Only Voltage Sense Mode Current Sense Mode, Odd Numbered Channels Only Voltage Sense Mode, VIN_ADC = 6V Current Sense Mode, Odd Numbered Channels Only, VIN_ADC = ±0.17V Voltage Sense Mode (Note 6) Current Sense Mode (Note 6) Temperature Input (Note 6) 10 10 2.55 120 3.26 90 2.5 55 MAX V mA mA V mV 3.47 3.47 140 2.6 80 V V mA V mA V ppm/°C ppm l 0 6 l –0.1 –0.1 –170 0.1 6 170 l l 122 15.625 31.25 62.5 125 250 l l l l l l l l l 6.15 24.6 24.6 1 62.5 UNITS 15 13 13 2.8 1.232 3 100 (Note 3) Differential Voltage: VIN_ADC = (VSENSEPn – VSENSEMn) Single-Ended Voltage: VSENSEMn Single-Ended Voltage: VSENSEPn, VSENSEMn Differential Voltage: VIN_ADC TYP V V V mV ±0.25 ±854 ±31.3 µV/LSB µV/LSB µV/LSB µV/LSB µV/LSB µV/LSB % µV µV ±400 ±31.3 µV µV ±250 ±35 µV µV ±0.2 ±0.2 % % ms ms ms pF kHz 2978fa LTC2978 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VPWR = VIN_SNS = 12V; VDD33, VDD25 and REF pins floating, unless otherwise indicated. CVDD33 = 100nF, CVDD25 = 100nF and CREF = 100nF. SYMBOL IIN_ADC PARAMETER Input Leakage Current Differential Input Current Voltage Buffered IDAC Output Characteristics N_VDACP Resolution VFS_VDACP Full-Scale Output Voltage (Programmable) INL_VDACP Integral Nonlinearity DNL_VDACP Differential Nonlinearity VOS_VDACP Offset Voltage VDACP Load Regulation (VDACPn – VDACMn) PSRR (VDACPn – VDACMn) DC CMRR (VDACPn – VDACMn) Leakage Current Short-Circuit Current Low Short-Circuit Current High COUT Output Capacitance tS_VDACP DAC Output Update Rate Voltage Supervisor Characteristics VIN_VS Input Voltage Range (Programmable) N_VS Voltage Sensing Resolution TUE_VS Total Unadjusted Error tS_VS Update Rate VIN_SNS Input Characteristics VVIN_SNS VIN_SNS Input Voltage Range RVIN_SNS VIN_SNS Input Resistance TUEVIN_SNS VIN_ON, VIN_OFF Threshold Total Unadjusted Error CONDITIONS VIN_ADC = 0V, 0V ≤ VCOMMONMODE ≤ 6V, Current Sense Mode VIN_ADC = 0.17V, Current Sense Mode VIN_ADC = 6V, Voltage Sense Mode TYP MAX ±0.5 UNITS µA l 80 10 250 15 nA µA DAC Code = 0x3FF Buffer Gain Setting_0 DAC Polarity = 1 Buffer Gain Setting_1 (Note 7) (Note 7) (Note 7) VDACPn = 2.65V, IVDACPn Sourcing = 2mA VDACPn = 0.1V, IVDACPn Sinking = 2mA DC: 3.13V ≤ VDD33 ≤ 3.47V, VPWR = VDD33 100mV Step in 20ns with 50pF Load –0.1V ≤ VDACMn ≤ 0.1V VDACPn Hi-Z, 0V ≤ VDACPn ≤ 6V VDACPn Shorted to GND VDACPn Shorted to VDD33 VDACPn Hi-Z Fast Servo Mode l l 10 1.38 2.65 VIN_VS = (VSENSEPn Low Resolution Mode – VSENSEMn) High Resolution Mode Single-Ended Voltage: VSENSEMn 0V to 3.8V Range: High Resolution Mode 0V to 6V Range: Low Resolution Mode 2V ≤ VIN_VS ≤ 6V, Low Resolution Mode 1.5V < VIN_VS ≤ 3.8V, High Resolution Mode 0.8V ≤ VIN_VS ≤ 1.5V, High Resolution Mode l l 3V ≤ VVIN_SNS ≤ 8V VVIN_SNS > 8V READ_VIN Total Unadjusted Error 3V ≤ VVIN_SNS ≤ 8V VVIN_SNS > 8V Voltage Buffered IDAC Soft-Connect Comparator Characteristics VOS_CMP Offset Voltage Temperature Sensor Characteristics TUE_TS Total Unadjusted Error VOUT Enable Output (VOUT_EN [3:0]) Characteristics VVOUT_ENn Output High Voltage IVOUT_ENn = –5µA, VDD33 = 3.3V MIN l l 1.32 2.53 l l l 1.44 2.77 ±2 ±2.4 ±10 100 100 60 40 60 ±100 –4 10 l l l –10 4 10 250 l 0 0 –0.1 6 3.8 0.1 4 8 ±1.25 ±1.0 ±1.5 l l l 12.21 l l 0 70 90 l l l l ±3 l 11.6 12.5 V V V mV/LSB mV/LSB % % % µs 15 110 ±2.0 ±1.0 ±1.5 ±1.0 V kΩ % % % % ±18 mV ±1 l Bits V V LSB LSB mV ppm/mA ppm/mA dB dB dB nA mA mA pF µs °C 14.7 V 2978fa LTC2978 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VPWR = VIN_SNS = 12V; VDD33, VDD25 and REF pins floating, unless otherwise indicated. CVDD33 = 100nF, CVDD25 = 100nF and CREF = 100nF. SYMBOL IVOUT_ENn PARAMETER Output Sourcing Current Output Sinking Current Output Leakage Current VOUT Enable Output (VOUT_EN [7:4]) Characteristics IVOUT_ENn Output Sinking Current Output Leakage Current VIN Enable Output (VIN_EN) Characteristics VVIN_EN Output High Voltage IVIN_EN Output Sourcing Current Output Sinking Current Leakage Current CONDITIONS VVOUT_ENn Pull-Up Enabled, VVOUT_ENn = 1V Strong Pull-Down Enabled, VVOUT_ENn = 0.4V Weak Pull-Down Enabled, VVOUT_ENn = 0.4V Internal Pull-Up Disabled, 0V ≤ VVOUT_ENn ≤ 15V l MIN –5 3 TYP –6 5 MAX –8 8 l 33 50 60 ±1 µA µA 3 6 9 mA ±1 µA 14.7 –8 8 60 ±1 V µA mA µA µA l l Strong Pull-Down Enabled, VOUT_ENn = 0.1V 0V ≤ VVOUT_ENn ≤ 6V l IVIN_EN = –5µA, VDD33 = 3.3V VIN_EN Pull-Up Enabled, VVIN_EN = 1V Strong Pull-Down Enabled, VVIN_EN = 0.4V Weak Pull-Down Enabled, VVIN_EN = 0.4V Internal Pull-Up Disabled, 0V ≤ VVIN_EN ≤ 15V l l l l l 11.6 –5 3 33 12.5 –6 5 50 l EEPROM Characteristics Endurance (Note 8) l 0°C < TJ < 85°C During EEPROM Write 10,000 Operations l Retention (Note 8) TA < 85°C 10 Mass_Write Mass Write Operation Time (Note 9) STORE_USER_ALL, 0°C < TJ < 85°C During l EEPROM Write Operations Digital Inputs SCL, SDA, CONTROL0, CONTROL1, WDI/RESETB, FAULTB00, FAULTB01, FAULTB10, FAULTB11, WP VIH High Level Input Voltage l VIL VHYST ILEAK Low Level Input Voltage Input Hysteresis Input Leakage Current l tSP Pulse Width of Spike Suppressed tRESETB Pulse Width to Assert Reset tWDI Pulse Width to Reset Watchdog Timer fWDI Watchdog Interrupt Input Frequency CIN Digital Input Capacitance Digital Input SHARE_CLK VIH High Level Input Voltage VIL Low Level Input Voltage fSHARE_CLK_IN Input Frequency Operating Range tLOW Assertion Low Time tRISE Rise Time ILEAK Input Leakage Current CIN Input Capacitance Cycles 440 4100 2.1 1.5 l ±2 V mV µA l ±2 µA 10 98 l l 300 0.3 200 1 l 10 l 1.6 0.8 110 1.1 450 ±1 l l VSHARE_CLK < 0.8V VSHARE_CLK < 0.8V to VSHARE_CLK > 1.6V 0V ≤ VSHARE_CLK ≤ VDD33 + 0.3V Years ms V 20 0V ≤ VPIN ≤ 5.5V, SDA, SCL, CONTROLx Pins Only 0V ≤ VPIN ≤ VDD33 + 0.3V, FAULTBxx, WDI/RESETB, WP Pins Only FAULTBxx, CONTROLx Pins Only SDA, SCL Pins Only VWDI/RESETB ≤ 1.5V VWDI/RESETB ≤ 1.5V UNITS µA mA l 90 0.825 l l 10 µs ns µs µs MHz pF V V kHz µs ns µA pF 2978fa LTC2978 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VPWR = VIN_SNS = 12V; VDD33, VDD25 and REF pins floating, unless otherwise indicated. CVDD33 = 100nF, CVDD25 = 100nF and CREF = 100nF. SYMBOL PARAMETER CONDITIONS Digital Outputs SDA, ALERTB, PWRGD, SHARE_CLK, FAULTB00, FAULTB01, FAULTB10, FAULTB11 VOL Digital Output Low Voltage ISINK = 3mA fSHARE_CLK_OUT Output Frequency Operating Range 5.49kΩ Pull-Up to VDD33 Digital Inputs ASEL0,ASEL1 VIH Input High Threshold Voltage VIL Input Low Threshold Voltage IIH,IL High, Low Input Current ASEL[1:0] = 0, VDD33 IIH, Z Hi-Z Input Current CIN Input Capacitance Serial Bus Timing Characteristics fSCL Serial Clock Frequency (Note 10) tLOW Serial Clock Low Period (Note 10) tHIGH Serial Clock High Period (Note 10) tBUF Bus Free Time Between Stop and Start (Note 10) tHD,STA Start Condition Hold Time (Note 10) tSU,STA Start Condition Setup Time (Note 10) tSU,STO Stop Condition Setup Time (Note 10) tHD,DAT Data Hold Time (LTC2978 Receiving Data) (Note 10) Data Hold Time (LTC2978 Transmitting Data) (Note 10) tSU,DAT Data Setup Time (Note 10) tSP Pulse Width of Spike Suppressed (Note 10) tTIMEOUT_BUS Time Allowed to Complete any PMBus Longer Timeout = 0 Command After Which Time SDA Will Longer Timeout = 1 Be Released and Command Terminated Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating for extended periods may affect device reliability and lifetime. Note 2: All currents into device pins are positive. All currents out of device pins are negative. All voltages are referenced to ground unless otherwise specified. If power is supplied to the chip via the VDD33 pin only, connect VPWR and VDD33 pins together. Note 3: Hysteresis in the output voltage is created by package stress that differs depending on whether the IC was previously at a higher or lower temperature. Output voltage is always measured at 25°C, but the IC is cycled to 85°C or –40°C before successive measurements. Hysteresis is roughly proportional to the square of the temperature change. Note 4: TUE(%) is defined as: Gain Error (%) + 100 • (INL + VOS)/VIN. Note 5: Integral nonlinearity (INL) is defined as the deviation of a code from a straight line passing through the actual endpoints of the transfer curve (0V and 6V). The deviation is measured from the center of the quantization band. MIN TYP MAX UNITS l 90 100 0.4 110 V kHz l VDD33 – 0.5 0.5 ±95 ±24 V V µA µA pF l l l l 10 l l l l 10 1.3 0.6 1.3 l 600 600 600 0 l 300 l 100 l l l 400 ns ns ns ns 900 25 200 ns ns ns 98 l l kHz µs µs µs 35 280 ms ms Note 6: The time between successive ADC conversions (latency of the ADC) for any given channel is given as: 36.9ms + (6.15ms • number of ADC channels configured in Low Resolution mode) + (24.6ms • number of ADC channels configured in High Resolution mode). Note 7: Nonlinearity is defined from the first code that is greater than or equal to the maximum offset specification to full-scale code, 1023. Note 8: EEPROM endurance and retention are guaranteed by design, characterization and correlation with statistical process controls. The minimum retention specification applies for devices whose EEPROM has been cycled less than the minimum endurance specification. Note 9: The LTC2978 will not acknowledge any PMBus write commands when a STORE_USER_ALL command is being executed. Note 10: Maximum capacitive load, CB, for SCL and SDA is 400pF. Data and clock rise time (tr) and fall time (tf) are: (20 + 0.1• CB) (ns) < tr < 300ns and (20 + 0.1 • CB) (ns) < tf < 300ns. CB = capacitance of one bus line in pF. SCL and SDA external pull-up voltage, VIO, is 3.13V < VIO < 5.5V. 2978fa LTC2978 Timing Diagram SDA tf tLOW tr tSU(DAT) tHD(SDA) tf tSP tr tBUF SCL tHD(STA) tHD(DAT) tSU(STA) tHIGH tSU(STO) 2978 TD START CONDITION REPEATED START CONDITION STOP CONDITION START CONDITION Typical Performance Characteristics ADC Total Unadjusted Error vs Temperature Temperature Sensor Error vs Temperature Reference Voltage vs Temperature 1.6 0.035 1.2350 1.4 0.030 REFERENCE OUTPUT VOLTAGE (V) 1.2355 1.2345 1.2 1.2340 ERROR (%) 1.2330 0.025 1.0 ERROR (°C) 1.2335 0.8 0.6 1.2325 THREE TYPICAL PARTS 1.2310 –50 –35 –20 –5 10 25 40 55 70 85 100 TEMPERATURE (°C) 0 –50 –35 –20 –5 10 25 40 55 70 85 100 TEMPERATURE (°C) ADC Zero Code Center Offset Voltage vs Temperature 2978 G03 ADC-INL 3.0 VOLTAGE SENSE MODE ADC-DNL 0.8 122µV/LSB 0.6 2.5 –40 2.0 0.4 –60 1.5 0.2 –80 –100 –120 ERROR (LSBs) –20 ERROR (LSBs) VOS (µV) 0 –50 –35 –20 –5 10 25 40 55 70 85 100 TEMPERATURE (°C) 2978 G02 2978 G01 0 0.015 0.005 0.2 1.2315 0.020 0.010 0.4 1.2320 1.0 122µV/LSB 0 –0.2 0.5 –0.4 0 –140 –0.5 –0.6 –160 –1.0 –0.8 –180 –50 –35 –20 –5 10 25 40 55 70 85 100 TEMPERATURE (°C) –1.5 –0.2 2978 G04 ADC VIN = 1.8V 0.8 1.8 2.8 3.8 4.8 INPUT VOLTAGE (V) 5.8 2978 G05 –1.0 –0.2 0.8 1.8 2.8 3.8 4.8 INPUT VOLTAGE (V) 5.8 2978 G06 2978fa LTC2978 Typical Performance Characteristics 0 ADC Rejection vs Frequency at VIN (Zoom) –20 –40 –40 –40 –60 –80 –120 REJECTION (dB) –20 –100 –60 –80 0 12500 25000 37500 50000 FREQUENCY (Hz) 62500 –120 0 3125 6250 9375 FREQUENCY (Hz) –60 –80 1200 0 3125 6250 9375 FREQUENCY (Hz) 0 VIN = 0V HIGH RESOLUTION MODE –0.05 600 400 –0.20 –0.25 –0.35 –10 0 10 READ_VOUT (µV) –0.40 –50 –35 –20 –5 10 25 40 55 70 85 100 TEMPERATURE (°C) 20 2978 G12 Voltage Buffered IDAC Full-Scale Output Voltage vs Temperature ADC High Resolution Mode Differential Input Current 90 2.698 8 80 2.696 3 2 1 0 0 1 2 3 4 INPUT VOLTAGE (V) 5 6 2978 G13 2.694 70 OUTPUT VOLTAGE (V) DIFFERENTIAL INPUT CURRENT (nA) 9 4 VIN = 0.8V HIGH RESOLUTION MODE –0.15 2978 G11 Input Sampling Current vs Differential Input Voltage 5 62500 –0.30 2978 G10 6 25000 37500 50000 FREQUENCY (Hz) –0.10 800 0 –20 12500 7 12500 Voltage Supervisor Total Unadjusted Error vs Temperature 200 –100 –120 0 2978 G09 ADC Noise Histogram NUMBER OF READINGS REJECTION (dB) –40 –80 2978 G08 1000 –20 –60 –120 12500 ERROR (%) 0 ADC Rejection vs Frequency at VIN (Current Sense Mode, Zoom) ADC Rejection vs Frequency at VIN (Current Sense Mode) –100 –100 2978 G07 INPUT SAMPLING CURRENT (µA) 0 –20 REJECTION (dB) REJECTION (dB) 0 ADC Rejection vs Frequency at VIN 60 50 40 30 2.692 2.690 2.688 2.686 2.684 20 2.682 10 2.680 0 0 20 40 60 80 100 120 140 160 180 DIFFERENTIAL INPUT VOLTAGE (mV) 2978 G14 2.678 –50 –35 –20 –5 10 25 40 55 70 85 100 TEMPERATURE (°C) 2978 G15 2978fa LTC2978 Typical Performance Characteristics 1.0 2.3 0.8 0.8 2.1 0.6 0.6 1.9 0.4 0.4 1.7 1.5 1.3 ERROR (LSBs) 1.0 0.2 0 –0.2 0.2 0 –0.2 1.1 –0.4 –0.4 0.9 –0.6 –0.6 0.7 –0.8 –0.8 0.5 –50 –35 –20 –5 10 25 40 55 70 85 100 TEMPERATURE (°C) –1.0 0 200 600 400 DAC CODE 2.688 2.686 2.684 2.682 2.678 85°C 0.1034 25°C 0.1032 0.1030 –40°C 0.1028 –40°C 2.680 0 –0.25 –0.5 –0.75 –1 –1.25 –1.50 1.75 CURRENT (mA) –2 SHORT-CIRCUIT CURRENT (mA) OUTPUT VOLTAGE (V) 25°C 800 0.1026 1000 9.00 0.1036 2.694 2.692 600 400 DAC CODE IDAC Voltage Buffer Short-Circuit Current vs Temperature 0.1038 2.690 200 2978 G18 IDAC Voltage Buffer Load Regulation (Sinking) 85°C 2.696 0 2978 G17 Voltage Buffered IDAC Load Regulation (Sourcing) 2.698 –1.0 1000 800 2978 G16 OUTPUT VOLTAGE (V) Voltage Buffered IDAC DNL Voltage Buffered IDAC-INL 2.5 ERROR (LSBs) OFFSET ERROR (mV) Voltage Buffered IDAC Offset Voltage vs Temperature 0 0.25 0.5 0.75 1 1.25 1.5 1.75 CURRENT (mA) 2978 G19 2 8.95 8.90 8.85 8.80 8.75 8.70 –50 –35 –20 –5 10 25 40 55 70 85 100 TEMPERATURE (°C) 2978 G21 2978 G20 IDAC Voltage Buffer Soft Connect Transient Response when Transitioning from Hi-Z State to ON State IDAC Voltage Buffer Transient Response to 1LSB DAC Code Change IDAC Voltage Buffer Soft Connect Transient Response when Transitioning from ON State to Hi-Z State CODE ‘h200 HI-Z 500µV/DIV HI-Z 10mV/DIV 10mV/DIV CONNECTED CODE ‘h1FF 2µs/DIV 2978 G22 500µs/DIV 100k SERIES RESISTANCE ON CODE: ‘h1FF CONNECTED 2978 G23 500µs/DIV 100k SERIES RESISTANCE ON CODE: ‘h1FF 2978 G24 2978fa 10 LTC2978 Typical Performance Characteristics 400 3.270 300 –86 85°C 200 3.265 3.260 3.255 3.250 3.245 25°C 100 –40°C 0 –100 –200 –300 3.240 –400 3.235 –50 –35 –20 –5 10 25 40 55 70 85 100 TEMPERATURE (°C) –500 4.5 10.16 6 7.5 9 10.5 VPWR (V) 12 13.5 9.9 3.1 3.2 3.3 3.4 3.5 3.6 VDD33 (V) 14.0 VPWR = 12V 10.12 10.10 13.5 10.06 11.0 10.0 9.5 10.02 –50 –35 –20 –5 10 25 40 55 70 85 100 TEMPERATURE (°C) 100 0.6 1.2 0.5 VOLTS (V) VOLTS (V) 100 1000 25°C 0.6 2978 G31 0 7 0.4 85°C 0.8 –40°C 85°C 0.3 25°C 0.2 –40°C 0.1 0.2 10 1 FREQUENCY (kHz) 6 VOUT_EN[7:4] VOL vs Current 1.4 0.4 0.1 2 3 4 5 CURRENT SOURCING (µA) 1 2978 G30 1.0 0.01 0.01 0 2978 G29 1000 0.1 –40°C 10.5 VOUT_EN[3:0] and VIN_EN VOL vs Current 1 25°C 12.5 11.5 10.08 Voltage Buffered IDAC Output Impedance vs Frequency 10 85°C 13.0 12.0 2978 G28 OUTPUT IMPEDANCE (Ω) VOUT_EN[3:0] and VIN_EN Output High Voltage vs Load Current 10.04 3 –98 2978 G27 CHARGE PUMP OUTUPT HIGH VOLTAGE (V) SUPPLY CURRENT (mA) SUPPLY CURRENT (mA) 10.0 –96 –102 –50 –35 –20 –5 10 25 40 55 70 85 100 TEMPERATURE (°C) 15 10.14 10.4 10.1 –94 Supply Current vs Temperature VPWR = VDD33 10.2 –92 2978 G26 Supply Current vs Supply Voltage 10.3 –90 –100 2978 G25 10.5 –88 SHORT-CIRCUIT CURRENT (mA) 3.275 9.8 VDD33 Regulator Short-Circuit Current vs Temperature VDD33 Regulator Line Regulation $VDD33 (ppm) VDD33 OUTPUT VOLTAGE (V) VDD33 Regulator Output Voltage vs Temperature 0 2 4 8 6 ISINK (mA) 10 12 2978 G32 0 0 4 8 12 16 ISINK (mA) 20 24 2978 G33 2978fa 11 LTC2978 Typical Performance Characteristics PWRGD and FAULTBzn VOL vs Current ALERTB VOL vs Current 1.2 1.4 1.0 1.2 1.0 VOLTS (V) VOLTS (V) 0.8 0.6 0.4 25°C 0.6 –40°C 0.4 85°C 25°C –40°C 0.2 0 85°C 0.8 0 2 4 6 8 ISINK (mA) 10 0.2 12 2978 G34 0 0 2 4 8 6 ISINK (mA) 10 12 2978 G35 Pin Functions PIN NAME VSENSEM6 VSENSEP7 VSENSEM7 VOUT_EN0 VOUT_EN1 VOUT_EN2 VOUT_EN3 VOUT_EN4 VOUT_EN5 VOUT_EN6 VOUT_EN7 VIN_EN DNC VIN_SNS PIN NUMBER PIN TYPE 1* In 2* In 3* In 4 Out 5 Out 6 Out 7 Out 8 Out 9 Out 10 Out 11 Out 12 0ut 13 Do Not Connect 14 In VPWR 15 In VDD33 16 In/Out VDD33 VDD25 WP PWRGD 17 18 19 20 In In/Out In Out SHARE_CLK WDI/RESET 21 22 In/Out In DESCRIPTION DC/DC Converter Differential (–) Output Voltage-6 Sensing Pin DC/DC Converter Differential (+) Output Voltage or Current-7 Sensing Pin DC/DC Converter Differential (–) Output Voltage or Current-7 Sensing Pin DC/DC Converter Enable-0 Pin. Output High Voltage Optionally Pulled Up to 12V by 5µA DC/DC Converter Enable-1 Pin. Output High Voltage Optionally Pulled Up to 12V by 5µA DC/DC Converter Enable-2 Pin. Output High Voltage Optionally Pulled Up to 12V by 5µA DC/DC Converter Enable-3 Pin. Output High Voltage Optionally Pulled Up to 12V by 5µA DC/DC Converter Open-Drain Pull-Down Output-4 DC/DC Converter Open-Drain Pull-Down Output-5 DC/DC Converter Open-Drain Pull-Down Output-6 DC/DC Converter Open-Drain Pull-Down Output-7 DC/DC Converter VIN ENABLE Pin. Output High Voltage Optionally Pulled Up to 12V by 5µA Do Not Connect to This Pin VIN SENSE Input. This Voltage is Compared Against the VIN On and Off Voltage Thresholds in Order to Determine When to Enable and Disable, Respectively, the Downstream DC/DC Converters VPWR Serves as the Unregulated Power Supply Input to the Chip (4.5V to 15V). If a 4.5V to 15V Supply Voltage is Unavailable, Short VPWR to VDD33 and Power the Chip Directly from a 3.3V Supply If Shorted to VPWR, it Serves as 3.13V to 3.47V Supply Input Pin. Otherwise it is a 3.3V Internally Regulated Voltage Output (Use 100nF Decoupling Capacitor to GND) Input for Internal 2.5V Sub-Regulator. Short This Pin to Pin 16 2.5V Internally Regulated Voltage Output. Bypass to GND with a 0.1µF Capacitor Digital Input. Write-Protect Input Pin, Active High Power Good Open-Drain Output. Indicates When Outputs are Power Good. Can be Used as System Power-On Reset Bidirectional Clock Sharing Pin. Connect a 5.49k Pull-Up Resistor to VDD33 Watchdog Timer Interrupt and Chip Reset Input. Connect a 10k Pull-Up Resistor to VDD33. Rising Edge Resets Watchdog Counter. Holding This Pin Low for More Than tRESETB Resets the Chip 2978fa 12 LTC2978 Pin Functions FAULTB00 23 In/Out Open-Drain Output and Digital Input. Active Low Bidirectional Fault Indicator-00. Connect a 10k Pull-Up Resistor to VDD33 FAULTB01 24 In/Out Open-Drain Output and Digital Input. Active Low Bidirectional Fault Indicator-01. Connect a 10k Pull-Up Resistor to VDD33 FAULTB10 25 In/Out Open-Drain Output and Digital Input. Active Low Bidirectional Fault Indicator-10. Connect a 10k Pull-Up Resistor to VDD33 FAULTB11 26 In/Out Open-Drain Output and Digital Input. Active Low Bidirectional Fault Indicator-11. Connect a 10k Pull-Up Resistor to VDD33 SDA 27 In/Out PMBus Bidirectional Serial Data Pin SCL 28 In PMBus Serial Clock Input Pin (400kHz Maximum) ALERTB 29 Out Open-Drain Output. Generates an Interrupt Request in a Fault/Warning Situation CONTROL0 30 In Control Pin 0 Input CONTROL1 31 In Control Pin 1 Input ASEL0 32 In Ternary Address Select Pin 0 Input. Connect to VDD33, GND or Float to Encode 1 of 3 Logic States ASEL1 33 In Ternary Address Select Pin 1 Input. Connect to VDD33, GND or Float to Encode 1 of 3 Logic States REFP 34 Out Reference Voltage Output. Needs 0.1µF Decoupling Capacitor to REFM REFM 35 Out Reference Return Pin. Needs 0.1µF Decoupling Capacitor to REFP. VSENSEP0 36* In DC/DC Converter Differential (+) Output Voltage-0 Sensing Pin VSENSEM0 37* In DC/DC Converter Differential (–) Output Voltage-0 Sensing Pin VDACM0 38 Out Voltage Buffered IDAC0 Return. Connect to Channel 0 DC/DC Converter’s GND Sense or Return to GND VDACP0 39 Out Voltage Buffered IDAC0 Output VDACP1 40 Out Voltage Buffered IDAC1 Output VDACM1 41 Out Voltage Buffered IDAC1 Return. Connect to Channel 1 DC/DC Converter’s GND Sense or Return to GND VSENSEP1 42* In DC/DC Converter Differential (+) Output Voltage or Current-1 Sensing Pins VSENSEM1 43* In DC/DC Converter Differential (–) Output Voltage or Current-1 Sensing Pins VDACP2 44 Out Voltage Buffered IDAC2 Output VDACM2 45 Out Voltage Buffered IDAC2 Return. Connect to Channel 2 DC/DC Converter’s GND Sense or Return to GND VSENSEP2 46* In DC/DC Converter Differential (+) Output Voltage-2 Sensing Pin VSENSEM2 47* In DC/DC Converter Differential (–) Output Voltage-2 Sensing Pin VSENSEP3 48* In DC/DC Converter Differential (+) Output Voltage or Current-3 Sensing Pins VSENSEM3 49* In DC/DC Converter Differential (–) Output Voltage or Current-3 Sensing Pins VDACP3 50 Out Voltage Buffered IDAC3 Output VDACM3 51 Out Voltage Buffered IDAC3 Return. Connect to Channel 3 DC/DC Converter’s GND Sense or Return to GND VSENSEP4 52* In DC/DC Converter Differential (+) Output Voltage-4 Sensing Pin VSENSEM4 53* In DC/DC Converter Differential (–) Output Voltage-4 Sensing Pin VDACM4 54 Out Voltage Buffered IDAC4 Return. Connect to Channel 4 DC/DC Converter’s GND Sense or Return to GND VDACP4 55 Out Voltage Buffered IDAC4 Output VDACP5 56 Out Voltage Buffered IDAC5 Output VDACM5 57 Out Voltage Buffered IDAC5 Return. Connect to Channel 5 DC/DC Converter’s GND Sense or Return to GND VDACM6 58 Out Voltage Buffered IDAC6 Return. Connect to Channel 6 DC/DC Converter’s GND Sense or Return to GND VDACP6 59 Out Voltage Buffered IDAC6 Output VDACP7 60 Out Voltage Buffered IDAC7 Output VDACM7 61 Out Voltage Buffered IDAC7 Return. Connect to Channel 7 DC/DC Converter’s GND Sense or Return to GND VSENSEP5 62* In DC/DC Converter Differential (+) Output Voltage or Current-5 Sensing Pins VSENSEM5 63* In DC/DC Converter Differential (–) Output Voltage or Current-5 Sensing Pins VSENSEP6 64* In DC/DC Converter Differential (+) Output Voltage-6 Sensing Pin GND 65 Ground Exposed Pad, Must be Soldered to PCB *Any unused VSENSEPn or VSENSEMn pins must be tied to GND. 2978fa 13 LTC2978 Block Diagram 3.3V REGULATOR VIN VOUT VPWR 15 VDD VDD33 16 2.5V REGULATOR VIN VOUT VDD25 18 VIN_SNS 14 3R VSENSEM0 VSENSEP0 R VSENSEM1 GND 65 INTERNAL TEMP SENSOR VSENSEP1 36 VSENSEP0 VSENSEM2 37 VSENSEM0 VSENSEP2 42 VSENSEP1 VSENSEM3 43 VSENSEM1 VSENSEP3 46 VSENSEP2 VSENSEM4 MUX VSENSEP4 CMP0 VSENSEM5 VSENSEP5 + – + – VDD33 17 47 VSENSEM2 + – 48 VSENSEP3 10-BIT VDAC 49 VSENSEM3 52 VSENSEP4 VSENSEM6 53 VSENSEM4 VSENSEP6 62 VSENSEP5 VSENSEM7 63 VSENSEM5 VSENSEP7 64 VSENSEP6 + 15-BIT – $∑ ADC 1 VSENSEM6 +SC 2 VSENSEP7 CMP0 ADC CLOCKS IDAC0 10 BITS 3 VSENSEM7 – + 39 VDACP0 VBUF0 – 40 VDACP1 VDD 44 VDACP2 50 VDACP3 REFERENCE 1.232V (TYP) REFP 34 55 VDACP4 56 VDACP5 REFM 35 59 VDACP6 60 VDACP7 38 VDACM0 41 VDACM1 SCL 28 SDA 27 ALERTB 29 ASEL0 32 45 VDACM2 NONVOLATILE MEMORY PMBus INTERFACE (400kHz I2C COMPATIBLE) ASEL1 33 51 VDACM3 EEPROM 54 VDACM4 RAM 57 VDACM5 ADC_RESULTS MONITOR LIMITS SERVO TARGETS 58 VDACM6 61 VDACM7 WP 19 4 VOUT_EN0 OUTPUT CONFIG CONTROL0 30 CONTROL1 31 OSCILLATOR WDI/RESET 22 FAULTB00 23 FAULTB01 24 FAULTB10 25 FAULTB11 26 PWRGD 20 SHARE_CLK 21 CONTROLLER PMBus ALGORITHM FAULT PROCESSOR WATCHDOG SEQUENCER CLOCK GENERATION 6 VOUT_EN2 7 VOUT_EN3 12 VIN_EN VDD UVLO 5 VOUT_EN1 8 VOUT_EN4 OPEN-DRAIN OUTPUT 9 VOUT_EN5 10 VOUT_EN6 11 VOUT_EN7 2978 BD 2978fa 14 LTC2978 Operation Operation Overview n The LTC2978 is a PMBus programmable power supply controller, monitor, sequencer and voltage supervisor that can perform the following operations: n Accept PMBus compatible programming commands. n n Provide DC/DC converter input voltage and output voltage/current read back through the PMBus interface. n Control the output of modules that set voltage with a trim pin or modules that set the output voltage using an external resistor feedback network. n Sequence the start-up of DC/DC converters via PMBus programming and the CONTROL input pins. n Trim the DC/DC converter output voltage (typically in 0.1% steps), in closed-loop servo operating mode, through PMBus programming. n Margin the DC/DC converter output voltage to PMBus programmed limits (typically ±10%). n Allow the user to trim or margin the DC/DC converter output voltage in a manual operating mode by providing direct access to the margin DAC. n Supervise the DC/DC converter output voltage, input voltage, and the LTC2978 die temperature for overvalue/undervalue conditions with respect to PMBus programmed limits and generate appropriate faults and warnings. n Respond to a fault condition by either continuing operation indefinitely, latching off after a programmable de-glitch period or latching off immediately. A retry mode may be used to automatically recover from a latched-off condition. n Stop trimming the DC/DC converter output voltage after it reached the initial margin or nominal target. Optionally allows servo to resume if target drifts outside of VOUT warning limits. Store command register contents to EEPROM through PMBus programming. Restore EEPROM contents through PMBus programming or on POR. Report the DC/DC converter output voltage status through the PMBus interface and the power good output. Generate interrupt requests by asserting the ALERTB pin in response to supported PMBus faults. n Shut down multiple DC/DC converters in response to a fault through the FAULTBz0 and FAULTBz1 pins. n Synchronize sequencing delays or shutdown for multiple devices using the SHARE_CLK pin. n Software and hardware write protect the command registers. n Disable the input voltage to the supervised DC/DC converters in response to output voltage OV and UV faults. n Log telemetry and status data to EEPROM in response to a faulted-off condition n Supervise an external microcontroller’s activity for a stalled condition with a programmable watchdog timer and reset it if necessary. n Prevent a DC/DC converter from re-entering the ON state after a power cycle until a programmable interval (MFR_RESTART_DELAY) has elapsed and its output has decayed below a programmable threshold voltage (MFR_VOUT_DISCHARGE_THRESHOLD). n Record minimum and maximum observed values of input voltage, output voltages and temperature. n n 2978fa 15 LTC2978 Operation PMBus Serial Digital Interface The LTC2978 communicates with a host (master) using the standard PMBus serial bus interface. The Timing Diagram shows the timing relationship of the signals on the bus. The two bus lines, SDA and SCL, must be high when the bus is not in use. External pull-up resistors or current sources are required on these lines. The LTC2978 is a slave device. The master can communicate with the LTC2978 using the following formats: Master transmitter, slave receiver Figures 1-10 illustrate the aforementioned SMBus protocols. All transactions support PEC (parity error check) and GCP (group command protocol). The Block Read supports 256 bytes of returned data. For this reason, the PMBus timeout may be extended using the Mfr_config_all_ longer_pmbus_timeout setting. The LTC2978 will not acknowledge any PMBus command if it is still busy with a STORE_USER_ALL, RESTORE_USER_ ALL, MFR_CONFIG or if fault log data is being written to the EEPROM. Status_word_busy will also be set. n Slave Address Master receiver, slave transmitter n The LTC2978 can be configured to respond to one of nine addresses for a given MFR_I2C_BASE_ADDRESS value (the factory default value for this register is 7’h5C). In addition, the LTC2978 will always respond to its global address and the PMBus Alert Response address regardless of the state of the address select pins. The following SMBus protocols are supported: Write Byte, Write Word, Send Byte n Read Byte, Read Word, Block Read n Alert Response Address n By connecting each of the address inputs to VDD33, GND, or by floating them, the user determines the slave address as shown in Table 1. Table 1. LTC2978 Address Look-Up Table DESCRIPTION HEX DEVICE ADDRESS BINARY DEVICE ADDRESS ADDRESS PINS 7’h 8’h 6 5 4 3 2 1 0 R/W ASEL1 ASEL0 Alert Response 0C 19 0 0 0 1 1 0 0 1 X X Global 5B B6 1 0 1 1 0 1 1 0 X X 0* 5C B8 1 0 1 1 1 0 0 0 L L 1 5D BA 1 0 1 1 1 0 1 0 L NC 2 5E BC 1 0 1 1 1 1 0 0 L H 3 5F BE 1 0 1 1 1 1 1 0 NC L 4 60 C0 1 1 0 0 0 0 0 0 NC NC 5 61 C2 1 1 0 0 0 0 1 0 NC H 6 62 C4 1 1 0 0 0 1 0 0 H L 7 63 C6 1 1 0 0 0 1 1 0 H NC 8 64 C8 1 1 0 0 1 0 0 0 H H H = Tie to VDD33, NC = No Connect, Open or Float, L = Tie to GND, X = Don’t Care *MFR_I2C_BASE_ADDRESS = 7’h5C (Factory Default) 2978fa 16 LTC2978 Operation 1 S 7 1 1 8 1 SLAVE ADDRESS Wr A COMMAND CODE A 8 1 1 DATA BYTE A P 2978 F01 Figure 1. Write Byte Protocol 1 S 7 1 1 8 1 SLAVE ADDRESS Wr A COMMAND CODE A 8 1 8 1 1 DATA BYTE LOW A DATA BYTE HIGH A P 2978 F02 Figure 2. Write Word Protocol 1 S 7 1 1 8 1 SLAVE ADDRESS Wr A COMMAND CODE A 8 1 8 1 1 DATA BYTE A PEC A P 2978 F03 Figure 3. Write Byte Protocol with PEC 1 S 7 1 1 8 1 SLAVE ADDRESS Wr A COMMAND CODE A 8 1 8 1 8 1 1 DATA BYTE LOW A DATA BYTE HIGH A PEC A P 2978 F04 Figure 4. Write Word Protocol with PEC 1 S 7 1 1 SLAVE ADDRESS Wr A 8 1 1 DATA BYTE A P 2978 F05 Figure 5. Send Byte Protocol 1 S 7 1 1 SLAVE ADDRESS Wr A 8 1 8 1 1 DATA BYTE A PEC A P 2978 F06 Figure 6. Send Byte Protocol with PEC 1 S 1 1 SLAVE ADDRESS Wr A COMMAND CODE A 7 1 1 8 S 7 1 1 SLAVE ADDRESS Rd A 8 1 DATA BYTE LOW A 1 1 DATA BYTE HIGH A 8 P 1 2978 F07 Figure 7. Read Word Protocol 1 S 1 1 SLAVE ADDRESS Wr A COMMAND CODE A 7 1 1 8 S 7 1 1 SLAVE ADDRESS Rd A 8 1 DATA BYTE LOW A 8 1 DATA BYTE HIGH A 8 1 1 PEC A P 1 2978 F08 Figure 8. Read Word Protocol with PEC 1 S 1 1 SLAVE ADDRESS Wr A COMMAND CODE A 7 1 1 8 S 8 1 1 SLAVE ADDRESS Rd A 8 1 1 DATA BYTE A P 1 2978 F09 Figure 9. Read Byte Protocol 1 S 1 1 SLAVE ADDRESS Wr A COMMAND CODE A 7 1 1 8 S 8 1 1 SLAVE ADDRESS Rd A 8 1 DATA BYTE A PEC 1 1 A P 1 2978 F10 Figure 10. Read Byte Protocol with PEC 2978fa 17 LTC2978 Operation Register Command Set Summary DATA NV LENGTH COMMAND MEMORY (BITS) BYTE VALUE TYPE DEFAULT VALUE PAGED ? ‘h00 N ‘h00 Y EEPROM ‘h12 Y ‘h03 NA Y 8 ‘h10 EEPROM ‘h00 N W 0 ‘h15 NA N Restore entire operating memory from EEPROM. W 0 ‘h16 NA N CAPABILITY The CAPABILITY command provides a way for a host system to determine the capabilities of the PMBus device. R 8 ‘h19 ROM ‘hE0 N VOUT_MODE Output voltage format control. R 8 ‘h20 ROM ‘h13 Y VOUT_COMMAND Servo DC/DC converter output voltage value setting. R/W 16 ‘h21 EEPROM ‘h2000 Y VOUT_MAX The VOUT_MAX command sets an upper limit on the output voltage, in volts, the unit can command regardless of any other commands or combinations. R/W 16 ‘h24 EEPROM ‘h8000 Y VOUT_MARGIN_HIGH Margin high DC/DC converter output voltage limit setting. R/W 16 ‘h25 EEPROM ‘h219A Y VOUT_MARGIN_LOW Margin low DC/DC converter output voltage limit setting. R/W 16 ‘h26 EEPROM ‘h1E66 Y VIN_ON The VIN_ON command sets the input voltage, in volts, at which the unit should start power conversion. R/W 16 ‘h35 EEPROM ‘hD280 N VIN_OFF The VIN_OFF command sets the input voltage, in volts, at which the unit should stop power conversion. R/W 16 ‘h36 EEPROM ‘hD240 N VOUT_OV_FAULT_LIMIT Overvoltage DC/DC converter fault limit setting. R/W 16 ‘h40 EEPROM ‘h2333 Y VOUT_OV_FAULT_RESPONSE The VOUT_OV_FAULT_RESPONSE command instructs the device on what action to take in response to an output overvoltage fault. R/W 8 ‘h41 EEPROM ‘h80 Y VOUT_OV_WARN_LIMIT Overvoltage DC/DC converter warning limit setting. R/W 16 ‘h42 EEPROM ‘h2266 Y VOUT_UV_WARN_LIMIT Undervoltage DC/DC converter warning limit setting. R/W 16 ‘h43 EEPROM ‘h1D9A Y COMMAND FUNCTION DESCRIPTION R/W PAGE R/W 8 ‘h00 OPERATION Operating mode control. R/W 8 ‘h01 EEPROM ON_OFF_CONFIG CONTROL pin and PMBus bus on/off command setting. R/W 8 ‘h02 CLEAR_FAULTS CLEAR_FAULTS is used to clear any fault bits that have been set. W 0 WRITE_PROTECT Provides protection against accidental changes. R/W STORE_USER_ALL Store entire operating memory to EEPROM. RESTORE_USER_ALL 2978fa 18 LTC2978 Operation Summary DATA NV LENGTH COMMAND MEMORY (BITS) BYTE VALUE TYPE DEFAULT VALUE PAGED ? EEPROM ‘h1CCD Y ‘h45 EEPROM ‘h7F Y 16 ‘h4F EEPROM ‘hEAA8 N R/W 8 ‘h50 EEPROM ‘hB8 N Overtemperature warning limit setting. R/W 16 ‘h51 EEPROM ‘hEA58 N UT_WARN_LIMIT Undertemperature warn limit setting. R/W 16 ‘h52 EEPROM ‘h8000 N UT_FAULT_LIMIT Undertemperature fault limit setting. R/W 16 ‘h53 EEPROM ‘hCD80 N UT_FAULT_RESPONSE The UT_FAULT_RESPONSE command instructs the device on what action to take in response to an undertemperature fault. R/W 8 ‘h54 EEPROM ‘hB8 N VIN_OV_FAULT_LIMIT Input supply overvoltage fault limit setting. R/W 16 ‘h55 EEPROM ‘hD3C0 N VIN_OV_FAULT_RESPONSE The VIN_OV_FAULT_RESPONSE command R/W instructs the device on what action to take in response to an input overvoltage fault. 8 ‘h56 EEPROM ‘h80 N VIN_OV_WARN_LIMIT Overvoltage input supply warning limit setting. R/W 16 ‘h57 EEPROM ‘hD380 N VIN_UV_WARN_LIMIT Undervoltage input supply warning limit setting. R/W 16 ‘h58 EEPROM ‘h8000 N VIN_UV_FAULT_LIMIT Undervoltage input supply fault limit setting. R/W 16 ‘h59 EEPROM ‘h8000 N VIN_UV_FAULT_RESPONSE The VIN_UV_FAULT_RESPONSE command R/W instructs the device on what action to take in response to an input undervoltage fault. 8 ‘h5A EEPROM ‘h00 N POWER_GOOD_ON Output voltage at or above which a power good should be asserted. R/W 16 ‘h5E EEPROM ‘h1EB8 Y POWER_GOOD_OFF Output voltage at or below which a power good should be deasserted. R/W 16 ‘h5F EEPROM ‘h1E14 Y TON_DELAY Time, in ms, from CONTROL and/or Operation on to VOUT_EN on. R/W 16 ‘h60 EEPROM ‘hBA00 Y TON_RISE Time, in ms, from when the output starts to rise until the LTC2978 optionally softconnects its voltage-buffered current DAC and begins to servo the output voltage to the desired value. R/W 16 ‘h61 EEPROM ‘hD280 Y TON_MAX_FAULT_LIMIT Maximum time, in ms, from VOUT_EN on assertion that an UV condition will be tolerated before a TON_MAX_FAULT condition results. R/W 16 ‘h62 EEPROM ‘hD3C0 Y TON_MAX_FAULT_RESPONSE Specifies response to a TON_MAX_FAULT event. R/W 8 ‘h63 EEPROM ‘hB8 Y COMMAND FUNCTION DESCRIPTION R/W VOUT_UV_FAULT_LIMIT Undervoltage DC/DC converter fault limit R/W setting. This limit is also used to determine if Ton_max_fault has been met and the unit is on. 16 ‘h44 VOUT_UV_FAULT_RESPONSE The VOUT_UV_FAULT_RESPONSE command instructs the device on what action to take in response to an undervoltage fault. R/W 8 OT_FAULT_LIMIT Overtemperature fault limit setting. R/W OT_FAULT_RESPONSE The OT_FAULT_RESPONSE command instructs the device on what action to take in response to an overtemperature fault. OT_WARN_LIMIT 2978fa 19 LTC2978 Operation Summary COMMAND FUNCTION DESCRIPTION R/W TOFF_DELAY Time, in ms, from CONTROL and/or Operation off to VOUT_EN off. R/W STATUS_BYTE Fault status reporting. STATUS_WORD The STATUS_WORD command returns two bytes of information with a summary of the unit’s fault condition. STATUS_VOUT DATA NV LENGTH COMMAND MEMORY (BITS) BYTE VALUE TYPE DEFAULT VALUE PAGED ? 16 ‘h64 EEPROM ‘hBA00 Y R 8 ‘h78 NA Y R 16 ‘h79 NA Y Voltage fault status reporting. R 8 ‘h7A NA Y STATUS_INPUT The STATUS_INPUT command returns one byte with status on VIN_SNS. R 8 ‘h7C NA N STATUS_TEMPERATURE The STATUS_TEMPERATURE command returns one byte with status information on temperature. R 8 ‘h7D NA N STATUS_CML The STATUS_CML command returns one byte with status information on communication and memory. R 8 ‘h7E NA N STATUS_MFR_SPECIFIC The STATUS_MFR_SPECIFIC command returns one byte with the manufacturer specific status information. R 8 ‘h80 NA Y READ_VIN Input supply voltage read back. R 16 ‘h88 NA N READ_VOUT DC/DC converter output voltage read back. R 16 ‘h8B NA Y READ_TEMPERATURE_1 Internal junction temperature read back. R 16 ‘h8D NA N PMBUS_REVISION Read the supported PMBus revision (1.1). R 8 ‘h98 ROM ‘h11 N MFR_CONFIG Manufacturer configuration bits that are channel specific. R/W 16 ‘hD0 EEPROM ‘h0080 Y MFR_CONFIG_ALL Manufacturer configuration bits that are common to all pages. R/W 8 ‘hD1 EEPROM ‘h7B N MFR_FAULTBz0_PROPAGATE Manufacturer configuration that determines which channel faults are propagated to FAULTBz0 where z = 0 for channels 0-3, and z=1 for channels 4-7. R/W 8 ‘hD2 EEPROM ‘h00 Y MFR_FAULTBz1_PROPAGATE Manufacturer configuration that determines which channel faults are propagated to FAULTBz1. R/W 8 ‘hD3 EEPROM ‘h00 Y MFR_PWRGD_EN Maps PWRGD status to the PWRGD pin. R/W 16 ‘hD4 EEPROM ‘h0000 N MFR_FAULTB00_RESPONSE Determines response to FAULTB00 pin being asserted low. R/W 8 ‘hD5 EEPROM ‘h00 N MFR_FAULTB01_RESPONSE Determines response to FAULTB01 pin being asserted low. R/W 8 ‘hD6 EEPROM ‘h00 N MFR_FAULTB10_RESPONSE Determines response to FAULTB10 pin being asserted low. R/W 8 ‘hD7 EEPROM ‘h00 N MFR_FAULTB11_RESPONSE Determines response to FAULTB11 pin being asserted low. R/W 8 ‘hD8 EEPROM ‘h00 N MFR_VINEN_OV_FAULT_RESPONSE Determines the response of the VIN_EN pin to a VOUT_OV_FAULT R/W 8 ‘hD9 EEPROM ‘h00 N 2978fa 20 LTC2978 Operation Summary DATA NV LENGTH COMMAND MEMORY (BITS) BYTE VALUE TYPE DEFAULT VALUE PAGED ? ‘h00 N EEPROM ‘hF320 N EEPROM ‘hFB20 N ‘hDD NA Y 16 ‘hDE NA N R 16 ‘hDF NA N Manufacturer register that contains the code of the 10-bit voltage-buffered current DAC. R/W 16 ‘hE0 EEPROM ‘h0000 Y MFR_POWERGOOD_ASSERTION_DELAY Determines power good output assertion delay. R/W 16 ‘hE1 EEPROM ‘hEB20 N MFR_WATCHDOG_T_FIRST First watchdog timer interval. R/W 16 ‘hE2 EEPROM ‘h8000 N MFR_WATCHDOG_T Watchdog timer interval. R/W 16 ‘hE3 EEPROM ‘h8000 N MFR_PAGE_FF_MASK Selects which channels respond to global page commands. R/W 8 ‘hE4 EEPROM ‘hFF N MFR_PADS Returns values detected and driven onto digital I/O pads. R 16 ‘hE5 N/A N MFR_I2C_BASE_ADDRESS This register determines the base value of the I2C address byte. R/W 8 ‘hE6 EEPROM ‘h5C N MFR_SPECIAL_ID This register contains the manufacturer code for identifying the LTC2978. R 16 ‘hE7 EEPROM ‘h0121 N MFR_SPECIAL_LOT These registers contain customer dependent codes that identify the factory programmed user configuration stored in EEPROM. R/W 8 ‘hE8 EEPROM Contact the Factory Y MFR_VOUT_DISCHARGE_THRESHOLD Coefficient used to multiply VOUT_ COMMAND in order to determine VOUT OFF threshold voltage. R/W 16 ‘hE9 EEPROM ‘hC200 Y MFR_FAULT_LOG_STORE Command a transfer of the fault log from RAM to EEPROM. This causes the part to behave as if a channel has faulted off. W 0 ‘hEA NA N MFR_FAULT_LOG_RESTORE Command a transfer of the fault log previously stored in EEPROM back to RAM. W 0 ‘hEB NA N MFR_FAULT_LOG_CLEAR Initialize the EEPROM block reserved for fault logging and clear any previous fault logging locks. W 0 ‘hEC NA N MFR_FAULT_LOG_STATUS This command returns one byte with status information on fault logging. R 8 ‘hED EEPROM NA N MFR_FAULT_LOG Fault log. Accessed using a block read. Returns data in the form last in first out. R 2048 ‘hEE EEPROM NA N COMMAND FUNCTION DESCRIPTION R/W MFR_VINEN_UV_FAULT_RESPONSE Determines the response of the VIN_EN pin to a VOUT_UV_FAULT R/W 8 ‘hDA EEPROM MFR_RETRY_DELAY Sets retry interval during retry mode. R/W 16 ‘hDB MFR_RESTART_DELAY Sets delay from actual CONTROL active edge to virtual CONTROL active edge. R/W 16 ‘hDC MFR_VOUT_PEAK Returns the maximum measured value of VOUT . R 16 MFR_VIN_PEAK Returns the maximum measured value of VIN_SNS. R MFR_TEMPERATURE_PEAK Returns the maximum measured value of temperature. MFR_DAC 2978fa 21 LTC2978 Operation Summary COMMAND FUNCTION DESCRIPTION R/W MFR_COMMON Contains manufacturer status bits that are common across multiple LTC chips. MFR_SPARE_0 DATA NV LENGTH COMMAND MEMORY (BITS) BYTE VALUE TYPE DEFAULT VALUE PAGED ? NA N R 8 ‘hEF Scratchpad register. R/W 16 ‘hF7 EEPROM ‘h0000 N MFR_SPARE_2 Paged scratchpad register. R/W 16 ‘hF9 EEPROM ‘h0000 Y MFR_VOUT_MIN Returns the minimum measured value of VOUT. R 16 ‘hFB NA Y MFR_VIN_MIN Returns the minimum measured value of VIN_SNS. R 16 ‘hFC NA N MFR_TEMPERATURE_MIN Returns the minimum measured junction temperature value. R 16 ‘hFD NA N Detailed PMBus Command Register Descriptions PAGE The PAGE command provides the ability to configure, control and monitor multiple outputs on one unit. Setting PAGE = ‘hFF allows PMBus commands that support global page programming to be written simultaneously. The only commands that support PAGE = ‘hFF are OPERATION and ON_OFF_CONFIG. See MFR_PAGE_FF_ MASK for additional options. Reading any PMBus register with PAGE = ‘hFF returns unpredictable data and will trigger a CML fault. PAGE Data Contents BIT(S) SYMBOL PURPOSE b[7:0] Page Page operation. ‘h00: All PMBus commands address channel/page 0. ‘h01: All PMBus commands address channel/page 1. • • • ‘h07: All PMBus commands address channel/page 7. ‘hXX: All nonspecified values reserved. ‘hFF: PMBus commands that support this global PAGE write mode will be written simultaneously. 2978fa 22 LTC2978 Operation OPERATION The OPERATION command is used to turn the unit on and off in conjunction with the CONTROLn pin and ON_OFF_ CONFIG. This command register responds to the global page command. The contents and functions of the data byte are shown in the following tables. OPERATION Data Contents When On_Off_Config_Use_PMBus Enables Operation_Control SYMBOL Action Operation_control[1:0] Operation_margin[1:0] Operation_fault[1:0] Reserved (read only) b[7:6] b[5:4] b[3:2] b[1:0] Turn off immediately 00 XX XX 00 Turn on 10 00 XX 00 Margin Low (Ignore Faults and Warnings) 10 01 01 00 Margin Low 10 01 10 00 Margin High (Ignore Faults and Warnings 10 10 01 00 10 10 10 00 01 00 XX 00 Sequence off and Margin Low (Ignore Faults and Warnings) 01 01 01 00 Sequence off and Margin Low 01 01 10 00 Sequence off and Margin High (Ignore Faults and Warnings) 01 10 01 00 Sequence off and Margin High 01 10 10 00 BITS Margin High FUNCTION Sequence off and margin to nominal Reserved All remaining combinations OPERATION Data Contents When On_Off_Config is Configured Such That OPERATION Command is Not Used to Command Channel On or Off SYMBOL Action Operation_control[1:0] Operation_margin[1:0] Operation_fault[1:0] Reserved (read only) b[7:6] b[5:4] b[3:2] b[1:0] Output at Nominal 00, 01 or 10 00 XX 00 Margin Low (Ignore faults and Warnings) 00, 01 or 10 01 01 00 Margin Low 00, 01 or 10 01 10 00 Margin High (Ignore Faults and Warnings 00, 01 or 10 10 01 00 Margin High 00, 01 or 10 10 10 00 BITS FUNCTION Reserved All remaining combinations 2978fa 23 LTC2978 Operation ON_OFF_CONFIG The ON_OFF_CONFIG command configures the combination of CONTROLn pin input and PMBus bus commands needed to turn the LTC2978 on/off, including the power-on behavior, as shown in the following table. This command register responds to the global page command. ON_OFF_CONFIG Data Contents BITS(S) SYMBOL b[7:5] Reserved OPERATION Don’t care. Always returns 0. b[4] On_off_config_controlled_on Control default autonomous power-up operation. 0: Unit powers up regardless of the CONTROLn pin. Unit always powers up with sequencing. To turn unit on without sequencing, set TON_DELAY = 0. 1: Unit does not power up unless commanded by the CONTROLn pin and/or the OPERATION command on the serial bus. If On_off_config[3:2] = 00, the unit never powers up. b[3] On_off_config_use_pmbus Controls how the unit responds to commands received via the serial bus. 0: Unit ignores the Operation_control[1:0]. 1: Unit responds to Operation_control[1:0]. Depending on On_off_config_use_control, the unit may also require the CONTROLn pin to be asserted for the unit to start. b[2] On_off_config_use_control Controls how unit responds to the CONTROLn pin. 0: Unit ignores the CONTROLn pin. 1: Unit requires the CONTROLn pin to be asserted to start the unit. Depending on On_off_config_use_ PMBus the OPERATION command may also be required to instruct the device to start. b[1] Reserved Not supported. Always returns 1. b[0] On_off_config_control_fast_off CONTROLn pin turn off action when commanding the unit to turn off 0: Use the programmed TOFF_DELAY. 1: Turn off the output and stop transferring energy as quickly as possible. The device does not sink current in order to decrease the output voltage fall time. 2978fa 24 LTC2978 Operation CLEAR_FAULTS The CLEAR_FAULTS command is used to clear any status faults that have been set. This command clears all bits in all unpaged status registers, and the paged status registers selected by the current PAGE setting. At the same time, the device negates (clears, releases) its contribution to ALERTB. The CLEAR_FAULTS command does not cause a unit that has latched off for a fault condition to restart. If the fault condition is present after the fault status is cleared, the fault status bit shall be set again and the host notified by the usual means. Note: this command register does not respond to the global page command. WRITE_PROTECT The WRITE_PROTECT command provides protection against accidental programming of the LTC2978 command registers. All supported commands may have their parameters read, regardless of the WRITE_PROTECT setting. WRITE_PROTECT Data Contents BITS(S) SYMBOL b[7:0] Write_protect[7:0] STORE_USER_ALL. No Data Contents. Accessing this command will store all operating memory commands with a corresponding EEPROM memory location. It is recommended that this command not be executed while a unit is enabled since all monitoring is suspended while the operating memory is transferred to EEPROM. RESTORE_USER_ALL. No Data Contents. Accessing this command will restore all commands from EEPROM Memory. It is recommend that this command not be executed while a unit is enabled since all monitoring is suspended while the EEPROM is transferred to operating memory, and intermediate values from EEPROM may not be compatible with the values initially stored in operating memory. CAPABILITY The CAPABILITY command provides a way for a host system to determine some key capabilities of the LTC2978. This one byte command is read only. CAPABILITY Data Contents BITS(S) SYMBOL b[7] Capability_pec Hard coded to 1 indicating Packet Error Checking is supported. Reading the Mfr_config_all_pec_en bit will indicate whether PEC is currently required. b[6] Capability_scl_max Hard coded to 1 indicating the maximum supported bus speed is 400kHz. b[5] Capability_smb_alert Hard coded to 1 indicating this device does have an ALERTB pin and does support the SMBus Alert Response Protocol. Reserved X: Always returns 0. OPERATION 8’b1000_0000: Disable all writes except to the WRITE_PROTECT, PAGE, and STORE_USER_ALL commands. 8’b0100_0000: Disable all writes except to the WRITE_PROTECT, PAGE, STORE_ USER_ALL, OPERATION, MFR_PAGE_ FF_MASK, and CLEAR_FAULTS. 8’b0000_0000: Enable writes to all commands. 8’bxxxx_xxxx: All other values reserved. OPERATION b[4:0] STORE_USER_ALL and RESTORE_USER_ALL STORE_USER_ALL, RESTORE_USER_ALL commands provide access to user nonvolatile EEPROM memory. Once a command is stored in EEPROM, it will be restored with explicit restore command or when the part emerges from power-on reset after power is applied. While either of these commands is being processed, the device will NACK I2C writes. 2978fa 25 LTC2978 Operation VOUT_MODE Output Voltage Related Commands The data byte for the VOUT_MODE command is 8 bits that consists of a three bit format and a five bit exponent. The three bit format specifies PMBus linear mode for all output voltage related commands. The five bit exponent provides the exponent for the mantissa specified in the data word. The LTC2978 device sets the format at the time of manufacture. The five bit exponent is read only and is set to a value of –13 decimal. Output voltage related commands are calculated as follows except for odd numbered channels configured to measure current: Voltage = V[15:0] • 2N where Voltage is the parameter of interest in volts. V is a 16-bit unsigned binary integer for all voltages, (e.g. Margin_high[15:0]); N = Vout_mode_exponent, is a 5-bit two’s complementary binary integer with a value hardwired to –13 decimal. VOUT_COMMAND, VOUT_MAX, VOUT_MARGIN_ HIGH, VOUT_MARGIN_LOW, VOUT_OV_FAULT_LIMIT, VOUT_OV_WARN_LIMIT, VOUT_UV_WARN_LIMIT, VOUT_UV_FAULT_LIMIT, POWER_GOOD_ON and POWER_GOOD_OFF These commands use the same format and provide various servo, margining, and supervising limits for a channel’s output voltage. When odd channels are configured to measure current, the OV_WARN_LIMIT, UV_WARN_LIMIT, OV_FAULT_LIMIT and UV_FAULT_LIMIT commands are not supported. Data Contents BIT(S) SYMBOL b[15:0] Vout_command[15:0], Vout_max[15:0], Vout_margin_high[15:0], Vout_margin_low[15:0], OPERATION These commands relate to output voltage. The data uses the linear mode format as defined by VOUT_MODE: Vout_mode_parameter is read only. Vout_ov_warn_limit[15:0], Vout_mode_type is read only. Vout_uv_fault_limit[15:0], V(Symbol) = Y • 2N where Y = b[15:0] is an unsigned integer and N = Vout_mode_ parameter is a 5-bit two’s complement exponent that’s hardwired to –13 decimal. Power_good_on[15:0], Units: V VOUT_MODE Data Contents BIT(S) SYMBOL OPERATION b[7:5] Vout_mode_type Reports linear mode. Hard wired to 3’b000. b[4:0] Vout_mode_parameter Linear mode exponent. 5-bit two’s complement integer. Hardwired to ‘h13 (–13 decimal). Vout_ov_fault_limit[15:0], Vout_uv_warn_limit[15:0], Power_good_off[15:0] 2978fa 26 LTC2978 Operation Input Voltage Related Commands VIN_ON, VIN_OFF, VIN_OV_FAULT_LIMIT, VIN_OV_ WARN_LIMIT, VIN_UV_WARN_LIMIT and VIN_UV_ FAULT_LIMIT These commands use the same format and provide voltage supervising limits for VIN. Data Contents BIT(S) SYMBOL OPERATION b[15:0] Vin_on[15:0], These commands relate to input voltage. The data uses the linear format: Vin_off[15:0], Vin_ov_fault_limit[15:0], Vin_ov_warn_limit[15:0], Vin_uv_warn_limit[15:0], Vin_uv_fault_limit[15:0] V(Symbol) = Y • 2N where N = b[15:11] is a 5-bit two’s complement integer and Y = b[10:0] is an 11-bit two’s complement integer Units: V. Temperature Related Commands OT_FAULT_LIMIT, OT_WARN_LIMIT, UT_WARN_LIMIT and UT_FAULT_LIMIT These commands provide supervising limits for temperature. Data Contents BIT(S) SYMBOL OPERATION b[15:0] Ot_fault_limit[15:0], The data uses the linear format: Ot_warn_limit[15:0], T(Symbol) = Y • 2N Ut_warn_limit[15:0], where N = b[15:11] is a 5-bit two’s complement integer and Ut_fault_limit[15:0] Y = b[10:0] is an 11-bit two’s complement integer Units: °C. TON_DELAY is the amount time in ms that elapses after the channel has been allowed on (usually due to CONTROLn pin or OPERATION command) until the channel enables the power supply. This delay is counted using SHARE_CLK only. TON_RISE is the amount of time in ms that elapses after the power supply has been enabled until the LTC2978’s voltage buffered current DAC soft connects and servo’s the output voltage to the desired level if Mfr_dac_mode = 2’b00. This delay is counted using SHARE_CLK only. TON_MAX_FAULT_LIMIT is the maximum amount of time that can elapse after the power supply has been enabled until the LTC2978 unmasks the VOUT_UV_FAULT_LIMIT threshold. (Note that a value of zero means there is no limit to how long the power supply can attempt to bring up its output voltage.) This delay is counted using SHARE_CLK only. TOFF_DELAY is the amount of time that elapses after the CONTROLn pin and/or OPERATION command is deasserted until the channel is disabled (soft-off). This delay is counted using SHARE_CLK if available, otherwise the internal oscillator is used. Data Contents BIT(S) SYMBOL OPERATION b[15:0] Ton_delay[15:0], The data uses the linear format: Ton_rise[15:0], T(Symbol) = Y • 2N Ton_max_fault_limit[15:0], Where N = b[15:11] is a 5-bit two’s complement integer and Toff_delay[15:0], Y = b[10:0] is an 11-bit two’s complement integer The internal timers operate on a 10µs internal clock. The SHARE_CLK pin may be used to synchronize the 10µs timer. Timer Limits Delays are rounded to the nearest 10µs TON_DELAY, TON_RISE, TON_MAX_FAULT_LIMIT and TOFF_DELAY Units: ms. Max value: 655ms These commands share the same format and provide sequencing and timer fault and warning delays in ms. 2978fa 27 LTC2978 Operation Fault Response for Voltages Measured by the High Speed Supervisor • Set the appropriate bit(s) in the STATUS_BYTE VOUT_OV_FAULT_RESPONSE and VOUT_UV_FAULT_ RESPONSE • Set the appropriate bit in the corresponding STATUS_ VOUT register, and The fault response documented here is for voltages that are measured by the high speed supervisor. These voltages are measured over a short period of time and may require a de-glitch period. Note that in addition to the response described by these commands, the LTC2978 will also: • Notify the host by pulling the ALERTB pin low. • Set the appropriate bit(s) in the STATUS_WORD Note: Odd numbered channels configured for high resolution ADC measurements will not respond to OV/UV faults or warnings. Data Contents BIT(S) SYMBOL OPERATION b[7:6] Vout_ov_fault_response_action, Response action. Vout_uv_fault_response_action 2’b00: The unit continues operation without interruption. 2’b01: The unit continues operating for the delay time specified by bits[2:0] in increments of Ts_vs. If the fault is still present at the end of the delay time, the unit responds as programmed in the retry setting (bits [5:3]). 2’b1X: The device shuts down and responds according to the retry setting in bits [5:3]. b[5:3] Vout_ov_fault_response_retry, Vout_uv_fault_response_retry Response action: 3’b000: A zero value for the retry setting means that the unit does not attempt to restart. The output remains disabled until the fault is cleared. 3’b001-111: The PMBus device attempts to restart continuously, without limitation, using Mfr_retry_delay, until it is commanded OFF (by the CONTROL pin or OPERATION command or both), bias power is removed, or another fault condition causes the unit to shut down. b[2:0] Vout_ov_fault_response_delay, Vout_uv_fault_response_delay This sample count determines the amount of time a unit is to ignore a fault after it is first detected. Use this delay to de-glitch fast faults. 3’b000: The unit turns off immediately. 3’b001 – 3’b111: The unit turns off after b[2:0] samples at the sampling period of Ts_vs (12.2µs typical). 2978fa 28 LTC2978 Operation Fault Response for Values Measured by the ADC • Set the appropriate bit(s) in the STATUS_BYTE OT_FAULT_RESPONSE, UT_FAULT_RESPONSE, VIN_OV_FAULT_RESPONSE and VIN_UV_FAULT_ RESPONSE • Set the appropriate bit(s) in the STATUS_WORD The fault response documented here is for values that are measured by the ADC. These values are measured over a longer period of time and are not de-glitched. Note that in addition to the response described by these commands, the LTC2978 will also: • Notify the host by pulling the ALERTB pin low. • Set the appropriate bit in the corresponding STATUS_VIN or STATUS_TEMPERATURE register, and Data Contents BIT(S) SYMBOL OPERATION b[7:6] Ot_fault_response_action, Response action: Ut_fault_response_action, 2’b00: The unit continues operation without interruption. Vin_ov_fault_response_action, 2’b01: The device shuts down and responds according to the retry setting in bits [5:3]. Vin_uv_fault_response_action 2’b10: The device shuts down and responds according to the retry setting in bits [5:3]. 2’b11: The device shuts down and responds according to the retry setting in bits [5:3]. b[5:3] Ot_fault_response_retry, Ut_fault_response_retry, Vin_ov_fault_response_retry, Vin_uv_fault_response_retry b[2:0] Ot_fault_response_delay, Response action: 3’b000: A zero value for the retry setting means that the unit does not attempt to restart. The output remains disabled until the fault is cleared. 3’b001-111: The PMBus device attempts to restart continuously, without limitation, using Mfr_retry_delay, until it is commanded OFF (by the CONTROLn pin or OPERATION command or both), bias power is removed, or another fault condition causes the unit to shut down. Hard coded to 3’b000. The unit turns off immediately. Ut_fault_response_delay, Vin_ov_fault_response_delay, Vin_uv_fault_response_delay 2978fa 29 LTC2978 Operation Timed Fault Response The device also: TON_MAX_FAULT_RESPONSE • Sets the HIGH_BYTE bit in the STATUS_BYTE, This command defines the LTC2978 response to a TON_MAX_FAULT. At start-up, the TON_MAX_FAULT_ RESPONSE is disarmed once the output voltage reaches the VOUT_UNDER_VOLTAGE_LIMIT. The only way to protect against a short-circuited output at start-up is to take action in response to a TON_MAX_FAULT since VOUT_UV_FAULT_RESPONSE is not armed until the output reaches the VOUT_UNDER_VOLTAGE_LIMIT. • Sets the VOUT bit in the STATUS_WORD, • Sets the TON_MAX_FAULT bit in the STATUS_VOUT register, and • Notifies the host by asserting ALERTB. TON_MAX_FAULT_RESPONSE Data Contents BIT(S) SYMBOL OPERATION b[7:6] Ton_max_fault_response_action Response action. 2’b00: The unit continues operation without interruption. 2’b01: The unit continues operating for the delay time specified which for this type of fault corresponds to an immediate shutdown. After shutting off, the device responds according to the retry settings in bits [5:3]. 2’b1X: The device shuts down and responds according to the retry setting in bits [5:3]. b[5:3] Ton_max_fault_response_retry Response action: 3’b000: A zero value for the Retry Setting means that the unit does not attempt to restart. The output remains disabled until the fault is cleared. 3’b001-111: The PMBus device attempts to restart continuously, without limitation, using Mfr_retry_delay, until it is commanded OFF (by the CONTROLn pin or OPERATION command or both), bias power is removed, or another fault condition causes the unit to shut down. b[2:0] Ton_max_fault_response_delay Hard coded to 3’b000. The unit turns off immediately. 2978fa 30 LTC2978 Operation STATUS_BYTE: STATUS_WORD Data Contents The STATUS_BYTE command returns the summary of the most critical faults or warnings which have occurred, as shown in the following table: BIT(S) SYMBOL OPERATION b[15] Status_word_vout An output voltage fault or warning has occurred. b[14] Status_word_iout Not supported. Always returns 0. STATUS_BYTE Data Contents b[13] Status_word_input An input voltage fault or warning has occurred. b[12] Status_word_mfr A manufacturer specific fault has occurred. BIT(S) SYMBOL OPERATION b[7] Status_byte_busy Device busy when PMBus command received. b[6] Status_byte_off This bit is asserted if the unit is not providing power to the output, regardless of the reason, including simply not being enabled. b[11] Status_word_power_not_good The POWER_GOOD signal, if present is negated. Power is not good. b[10] Status_word_cooling Not supported. Always returns 0. b[5] Status_byte_vout_ov An output overvoltage fault has occurred. b[9] Status_word_other Not supported. Always returns 0. b[8] Status_word_unknown Not supported. Always returns 0. b[4] Status_byte_iout_oc Not supported. Always returns 0. b[7] Status_word_busy b[3] Status_byte_vin_uv A VIN undervoltage fault has occurred. Device busy when PMBus command received. b[2] Status_byte_temp A temperature fault or warning has occurred. b[6] Status_word_off Status_byte_off b[5] Status_word_vout_ov Status_byte_vout_ov b[1] Status_byte_cml A communication, memory or logic fault has occurred. b[4] Status_word_iout_oc Not supported. Always returns 0. b[3] Status_word_vin_uv Status_byte_vin_uv b[2] Status_word_temp Status_byte_temp b[1] Status_word_cml Status_byte_cml b[0] Status_word_high_byte A bit in the high byte of the STATUS_WORD (b[15:8]) is set. b[0] Status_byte_high_byte Fault/warning not listed in b[7:1]. STATUS_WORD: The STATUS_WORD command returns two bytes of information with a summary of the unit’s fault condition. Based on the information in these bytes, the host can get more information by reading the appropriate status byte. The low byte of the STATUS_WORD is the same register as the STATUS_BYTE command. 2978fa 31 LTC2978 Operation STATUS_VOUT STATUS_TEMPERATURE The STATUS_VOUT command returns the summary of the voltage faults or warnings which have occurred, as shown in the following table: The STATUS_TEMPERATURE command returns the summary of the temperature faults or warnings which have occurred, as shown in the following table: STATUS_VOUT Data Contents STATUS_TEMPERATURE Data Contents BIT(S) SYMBOL OPERATION Bit(s) Symbol Operation b[7] Status_vout_ov_fault Overvoltage fault. b[7] Status_temperature_ot_fault Overtemperature fault. b[6] Status_vout_ov_warn Overvoltage warning. b[6] Status_temperature_ot_warn Overtemperature warning. b[5] Status_vout_uv_warn Undervoltage warning b[5] Status_temperature_ut_warn Undertemperature warning. b[4] Status_vout_uv_fault Undervoltage fault. b[4] Status_temperature_ut_fault Undertemperature fault. b[3] Status_vout_max_fault VOUT_MAX fault. An attempt has been made to set the output voltage to a value higher than allowed by the VOUT_MAX command. b[3] Reserved Reserved. Always returns 0. b[2] Reserved Reserved. Always returns 0. b[1] Reserved Reserved. Always returns 0. b[0] Reserved Reserved. Always returns 0. b[2] Status_vout_ton_max_fault TON_MAX_FAULT sequencing fault. b[1] Status_vout_toff_max_warn Not supported. Always returns 0. b[0] Status_vout_tracking_error Not supported. Always returns 0. STATUS_INPUT The STATUS_INPUT command returns the summary of the VIN faults or warnings which have occurred, as shown in the following table: STATUS_CML The STATUS_CML command returns the summary of the communication, memory and logic faults or warnings which have occurred, as shown in the following table: STATUS_CML Data Contents BIT(S) SYMBOL b[7] Status_cml_cmd_fault STATUS_INPUT Data Contents BIT(S) SYMBOL OPERATION b[7] Status_input_ov_fault VIN Overvoltage fault b[6] Status_input_ov_warn VIN Overvoltage warning b[5] Status_input_uv_warn VIN Undervoltage warning b[4] Status_input_uv_fault VIN Undervoltage fault b[3] Status_input_off Unit is off for insufficient input voltage. b[2] IIN overcurrent fault Not supported. Always returns 0. b[1] IIN overcurrent warn Not supported. Always returns 0. b[0] PIN overpower warn Not supported. Always returns 0. OPERATION 1 = An illegal or unsupported command fault has occurred. 0 = No fault has occurred. b[6] Status_cml_data_fault b[5] Status_cml_pec_fault b[4] Status_cml_memory_fault 1 = Illegal or unsupported data received. 0 = No fault has occurred. 1 = A PEC fault has occurred. 0 = No fault has occurred. 1 = A fault has occurred in the NVM. 0 = No fault has occurred. b[3] Status_cml_processor_fault Not supported, always returns 0. b[2] Reserved Not supported, always returns 0. b[1] Status_cml_PMBus_fault 1 = A communication fault other than ones listed in this table has occurred. b[0] Status_cml_unknown_fault 0 = No fault has occurred. Not supported, always returns 0. 2978fa 32 LTC2978 Operation STATUS_MFR_SPECIFIC The STATUS_MFR_SPECIFIC command returns manufacturer specific status flags. Bits marked FAULT = No are intended to support polled handshaking; these are not latched nor do they assert ALERTB. Bits marked Channel = All can be read from any page. Bits marked FAULT = Yes assert ALERTB low and are cleared by CLEAR_FAULTS. STATUS_MFR_SPECIFIC Data Contents BIT(S) SYMBOL CHANNEL FAULT b[7] Status_mfr_discharge OPERATION 1 = A VOUT discharge fault occurred while attempting to enter the ON state 0 = No VOUT discharge fault has occurred Current Page Yes b[6] Status_mfr_fault1_in This channel attempted to turn on while the FAULTBz1 pin was asserted low, Current Page or this channel has shut down at least once in response to a FAULTBz1 pin asserting low since the last CONTROLn pin toggle, OPERATION command ON/OFF cycle or CLEAR_FAULTS command. Yes b[5] Status_mfr_fault0_in This channel attempted to turn on while the FAULTBz0 pin was asserted low, Current Page or this channel has shut down at least once in response to a FAULTBz0 pin asserting low since the last CONTROLn pin toggle, OPERATION command ON/OFF cycle or CLEAR_FAULTS command. Yes b[4] Status_mfr_servo_target_reached Servo target has been reached. Current Page No b[3] Status_mfr_dac_connected DAC is connected and driving VDACP pin. Current Page No b[2] Status_mfr_dac_saturated A previous servo operation terminated with maximum or minimum DAC value. Current Page Yes b[1] Status_mfr_vinen_faulted_off VIN_EN has been deasserted due to a VOUT fault. All No b[0] Status_mfr_watchdog_fault 1 = A watchdog fault has occurred. 0 = No watchdog fault has occurred. All Yes 2978fa 33 LTC2978 Operation ADC Monitoring Commands READ_VIN This command returns the most recent ADC measured value of the voltage measured at the VIN_SNS pin. READ_VIN Data Contents BIT(S) SYMBOL READ_TEMPERATURE_1 This command returns the most recent ADC measured value of junction temperature in °C as determined by the LTC2978’s internal temperature sensor. READ_TEMPERATURE_1 Data Contents BIT(S) SYMBOL OPERATION OPERATION b[15:0] Read_temperature_1 [15:0] The data uses the linear format: Temp(Symbol) = Y • 2N b[15:0] Read_vin[15:0] The data uses the linear format: V(Symbol) = Y • 2N Where N = b[15:11] is a 5-bit two’s complement integer and where N = b[15:11] is a 5-bit two’s complement integer and Y = b[10:0] is an 11-bit two’s complement integer Y = b[10:0] is an 11-bit two’s complement integer Units: V READ_VOUT This command returns the most recent ADC measured value of the channel’s output voltage. When odd channels are configured to measure current, the data contents have a slightly modified meaning, as described in the second table below. READ_VOUT Data Contents BIT(S) SYMBOL OPERATION Units: °C. PMBUS_REVISION The PMBUS_REVISION command register is read only and reports the LTC2978 compliance to the PMBus standard revision 1.1. PMBUS_REVISION Data Contents BIT(S) SYMBOL OPERATION b[7:0] PMBus_rev Reports the PMBus standard revision compliance. This is hard-coded to ‘h11 for revision 1.1. b[15:0] Read_vout[15:0] The data uses the linear mode format as defined by VOUT_MODE: V(Read_vout) = Y • 2N where Y = b[15:0] is an unsigned integer and N = Vout_mode_ parameter is a 5-bit two’s complement exponent that’s hardwired to –13 decimal. Units: V. READ_VOUT Data Contents—for Odd Channels Configured to Measure Current Bit(s) Symbol Operation b[15:0] Read_vout[15:0] The data uses the linear format: V(Symbol) = Y • 2N where N = b[15:11] is a 5-bit two’s complement integer and Y = b[10:0] is an 11-bit two’s complement integer Units: mV 2978fa 34 LTC2978 Operation Manufacturer Specific Commands MFR_CONFIG: This command is used to configure various manufacturer specific operating parameters for each channel. MFR_CONFIG Data Contents BIT(S) SYMBOL b[15:12] Reserved b[11] Mfr_config_fast_servo_off b[10] b[9] b[8] b[7] b[6] b[5:4] b[3] b[2] b[1] b[0] OPERATION Don’t care. Always returns 0. Disables fast servo when margining or trimming output voltages: 0: fast-servo enabled. 1: fast-servo disabled. Mfr_config_supervisor_resolution Selects supervisor resolution: 0: high resolution – 4mV/LSB, range for VSENSEP is 0V to 3.8V. 1: low resolution – 8mV/LSB, range for VSENSEP is 0V to 6.0V. Mfr_config_adc_hires Selects ADC resolution for odd channels. Ignored for even channels (they always use low res). 0: low resolution – 122µV/LSB. 1: high resolution – 15.6µV/LSB. Mfr_config_controln_sel Selects the active control pin input (CONTROL0 or CONTROL1) for this channel. 0: Select CONTROL0 pin. 1: Select CONTROL1 pin. Mfr_config_servo_continuous Select whether the UNIT should continuously servo VOUT after it has reached a new margin or nominal target. Only applies when Mfr_dac_mode = 2’b00. 0: Do not continuously servo VOUT after reaching initial target. 1: Continuously servo VOUT to target. Mfr_config_servo_on_warn Control re-servo on warning feature. Only applies when Mfr_config_dac_mode = 2’b00 and Mfr_config_servo_continuous = 0. 0: Do not allow the unit to re-servo when a VOUT warning threshold is met or exceeded. 1: Allow the unit to re-servo VOUT to nominal target if VOUT ≥ V(Vout_ov_warn_limit) or VOUT ≤ V(Vout_uv_warn_limit). Mfr_config_dac_mode Determines how DAC is used when channel enters ON state or is already in ON state. 00: Soft connect (if needed) and servo to target. Wait for TON_RISE if just entering ON state. 01: DAC not connected. 10: DAC connected using value from MFR_DAC command. Does not wait for TON_RISE if just entering ON state. 11: DAC is soft connected. After soft connect is complete MFR_DAC may be written. Mfr_config_vo_en_wpu_en VO_EN charge pumped, current-limited pull-up enable. 0: Disable weak pull-up. VO_EN driver is three-stated when channel is on. 1: Use weak current-limited pull-up on VO_EN when the channel is on. For channels 4-7 this bit is treated as a 0 regardless of its value. Mfr_config_vo_en_wpd_en VO_EN current-limited pull-down enable. 0: Use a fast N-channel device to pull down VO_EN when the channel is off for any reason. 1: Use weak current-limited pull-down to discharge VO_EN when channel is off due to soft stop by the CONTROLn pin and/or OPERATION command. If the channel is off due to a fault, use the fast pull-down on VO_EN. For channels 4-7 this bit is treated as a 0 regardless of its value. Mfr_config_dac_gain DAC buffer gain. 0: Select DAC buffer gain dac_gain_0 (1.38V full-scale) 1: Select DAC buffer gain dac_gain_1 (2.65V full-scale) Mfr_config_dac_pol DAC output polarity. 0: Encodes negative (inverting) DC/DC converter trim input. 1: Encodes positive (noninverting) DC/DC converter trim input. 2978fa 35 LTC2978 Operation MFR_CONFIG_ALL: This command is used to configure parameters that are common to all channels on the IC. They may be set or reviewed from any PAGE setting. MFR_CONFIG_ALL Data Contents MFR_CONFIG_ALL Data Contents BIT(S) SYMBOL b[7] Mfr_config_fault_log_enable b[6] Mfr_vin_on_clr_faults_en b[5] Mfr_config_control1_pol b[4] Mfr_config_control0_pol OPERATION Enable fault logging to NVM in response to Fault. 0: Fault logging to NVM is disabled 1: Fault logging to NVM is enabled VIN_ON rising edge to clear all latched faults 0: VIN_ON clear faults feature is disabled 1: VIN_ON clear faults feature is enabled Selects active polarity of control1 pin. 0: Active low (pull pin low to start unit) 1: Active high (pull pin high to start unit) Selects active polarity of control0 pin. 0: Active low (pull pin low to start unit) 1: Active high (pull pin high to start unit) b[3] b[2] b[1] b[0] Mfr_config_vin_share_enable Allow this unit to hold shareclock pin low when VIN_ON has fallen below VIN_OFF. When enabled, this unit will also turn all channels off in response to share-clock being held low. 0: Share-clock inhibit is disabled 1: Share-clock inhibit is enabled Mfr_config_all_pec_en PMBus packet error checking enable. 0: PEC is accepted but not required 1: PEC is required Mfr_config_all_longer_ Increase PMBus timeout internal pmbus_timeout by a factor of 8. 0: PMBus timeout is not multiplied by a factor of 8 1: PMBus timeout is multiplied by a factor of 8 Mfr_config_all_vinen_wpu_ VIN_EN charge pumped, currentdis limited pull-up disable. 0: Use weak current-limited pullup on VIN_EN after power-up, as long as no faults have forced VIN_EN off. 1: Disable weak pull-up. VIN_EN driver is three-stated after power-up as long as no faults have forced VIN_EN off. 2978fa 36 LTC2978 Operation MFR_FAULTB00_PROPAGATE, MFR_FAULTB01_ PROPAGATE, MFR_FAULTB10_PROPAGATE and MFR_FAULTB11_PROPAGATE These manufacturer specific commands enable channels that have faulted off to propagate that state to the appropriate fault pin. There are two zones in the LTC2978. In zone 0, faulted off states for channels 0 through 3 can be propagated to FAULT00 or FAULT01. In zone 1, faulted off states for channels 4 through 7 can be propagated to FAULT10 or FAULT11. See Figure 13. MFR_FAULTB00_PROPAGATE Data Contents—Fault Zone 0 (Pages 0-3) BIT(S) SYMBOL OPERATION b[7:1] Reserved Don’t care. Always returns 0. b[0] Enable fault propagation. 0: FAULTB00 will not be affected if a fault is declared. 1: FAULTB00 will be asserted low if a fault is declared. Mfr_faultb00_propagate MFR_FAULTB10_PROPAGATE Data Contents—Fault Zone 1 (Pages 4-7) BIT(S) SYMBOL OPERATION b[7:1] Reserved Don’t care. Always returns 0. b[0] Enable fault propagation. 0: FAULTB10 will not be affected if a fault is declared. 1: FAULTB10 will be asserted low if a fault is declared. Mfr_faultb10_propagate MFR_FAULTB11_PROPAGATE Data Contents—Fault Zone 1 (Pages 4-7) BIT(S) SYMBOL OPERATION b[7:1] Reserved Don’t care. Always returns 0. b[0] Enable fault propagation. 0: FAULTB11 will not be affected if a fault is declared. 1: FAULTB11 will be asserted low if a fault is declared. Mfr_faultb11_propagate MFR_FAULTB01_PROPAGATE Data Contents—Fault Zone 0 (Pages 0-3) BIT(S) SYMBOL OPERATION b[7:1] Reserved Don’t care. Always returns 0. b[0] Enable fault propagation. 0: FAULTB01 will not be affected if a fault is declared. 1: FAULTB01 will be asserted low if a fault is declared. Mfr_faultb01_propagate 2978fa 37 LTC2978 Operation MFR_PWRGD_EN This command register controls the mapping of power good status to the power good pin. Note that odd numbered channels whose ADC is in high res mode do not contribute to power good. MFR_PWRGD_EN Data Contents BIT(S) SYMBOL OPERATION b[15:9] Reserved Read only, always returns 0s. b[8] Mfr_pwrgd_en_wdog Watchdog 1 = Watchdog timer not-expired status is ANDed with PWRGD status for any similarly enabled channels to determine when the PWRGD pin gets asserted. 0 = Watchdog timer does not affect the PWRGD pin. b[7] Mfr_pwrgd_en_chan7 Channel 7 1 = PWRGD status for this channel is ANDed with PWRGD status for any similarly enabled channels to determine when the PWRGD pin gets asserted. 0 = PRWGD status for this channel does not affect the PWRGD pin. b[6] Mfr_pwrgd_en_chan6 Channel 6 1 = PWRGD status for this channel is ANDed with PWRGD status for any similarly enabled channels to determine when the PWRGD pin gets asserted. 0 = PRWGD status for this channel does not affect the PWRGD pin. b[5] Mfr_pwrgd_en_chan5 Channel 5 1 = PWRGD status for this channel is ANDed with PWRGD status for any similarly enabled channels to determine when the PWRGD pin gets asserted. 0 = PRWGD status for this channel does not affect the PWRGD pin. b[4] Mfr_pwrgd_en_chan4 Channel 4 1 = PWRGD status for this channel is ANDed with PWRGD status for any similarly enabled channels to determine when the PWRGD pin gets asserted. 0 = PRWGD status for this channel does not affect the PWRGD pin. b[3] Mfr_pwrgd_en_chan3 Channel 3 1 = PWRGD status for this channel is ANDed with PWRGD status for any similarly enabled channels to determine when the PWRGD pin gets asserted. 0 = PRWGD status for this channel does not affect the PWRGD pin. b[2] Mfr_pwrgd_en_chan2 Channel 2 1 = PWRGD status for this channel is ANDed with PWRGD status for any similarly enabled channels to determine when the PWRGD pin gets asserted. 0 = PRWGD status for this channel does not affect the PWRGD pin. b[1] Mfr_pwrgd_en_chan1 Channel 1 1 = PWRGD status for this channel is ANDed with PWRGD status for any similarly enabled channels to determine when the PWRGD pin gets asserted. 0 = PRWGD status for this channel does not affect the PWRGD pin. b[0] Mfr_pwrgd_en_chan0 Channel 0 1 = PWRGD status for this channel is ANDed with PWRGD status for any similarly enabled channels to determine when the PWRGD pin gets asserted. 0 = PRWGD status for this channel does not affect the PWRGD pin. 2978fa 38 LTC2978 Operation MFR_FAULTB00_RESPONSE, MFR_FAULTB01_ RESPONSE, MFR_FAULTB10_RESPONSE and MFR_ FAULTB11_RESPONSE These manufacturer specific commands share the same format and specify the response to assertions of the bidirectional fault pins. For fault zone 0, MFR_FAULTB00_RESPONSE determines how channels 0-3 respond when the FAULTB00 pin is asserted, and MFR_FAULTB01_ RESPONSE determines how channels 0-3 respond when the FAULTB01 pin is asserted. For fault zone 1, MFR_FAULTB10_RESPONSE determines how channels 4-7 respond when the FAULTB10 pin is asserted, and MFR_FAULTB11_RESPONSE determines how channels 4-7 respond when the FAULTB11 pin is asserted. If one or more bits in the MFR_FAULTBzn_RESPONSE registers are set, a FAULTBzn assertion will cause the ALERTB pin to assert low and set the appropriate bit in the STATUS_MFR_ SPECIFIC register. Data Contents—Fault Zone 0 Response Commands BIT(S) SYMBOL b[7:4] Reserved b[3] Mfr_faultb00_response_chan3, Mfr_faultb01_response_chan3 b[2] Mfr_faultb00_response_chan2, Mfr_faultb01_response_chan2 b[1] Mfr_faultb00_response_chan1, Mfr_faultb01_response_chan1 b[0] Mfr_faultb00_response_chan0, Mfr_faultb01_response_chan0 OPERATION Read only, always returns 0s. Channel 3 response. 0: The channel continues operation without interruption. 1: The channel shuts down if the corresponding FAULTBzn pin is still asserted after 10µs. When the FAULTBzn pin subsequently deasserts, the channel turns back on, honoring TON_DELAY and TON_RISE settings. Channel 2 response. 0: The channel continues operation without interruption. 1: The channel shuts down if the corresponding FAULTBzn pin is still asserted after 10µs. When the FAULTBzn pin subsequently deasserts, the channel turns back on, honoring TON_DELAY and TON_RISE settings. Channel 1 response. 0: The channel continues operation without interruption. 1: The channel shuts down if the corresponding FAULTBzn pin is still asserted after 10µs. When the FAULTBzn pin subsequently deasserts, the channel turns back on, honoring TON_DELAY and TON_RISE settings. Channel 0 response. 0: The channel continues operation without interruption. 1: The channel shuts down if the corresponding FAULTBzn pin is still asserted after 10µs. When the FAULTBzn pin subsequently deasserts, the channel turns back on, honoring TON_DELAY and TON_RISE settings. Data Contents—Fault Zone 1 Response Commands BIT(S) SYMBOL b[7:4] Reserved b[3] Mfr_faultb10_response_chan7, Mfr_faultb11_response_chan7 b[2] Mfr_faultb10_response_chan6, Mfr_faultb11_response_chan6 b[1] Mfr_faultb10_response_chan5, Mfr_faultb11_response_chan5 b[0] Mfr_faultb10_response_chan4, Mfr_faultb11_response_chan4 OPERATION Read only, always returns 0s. Channel 7 response. 0: The channel continues operation without interruption. 1: The channel shuts down if the corresponding FAULTBzn pin is still asserted after 10µs. When the FAULTBzn pin subsequently deasserts, the channel turns back on, honoring TON_DELAY and TON_RISE settings. Channel 6 response. 0: The channel continues operation without interruption. 1: The channel shuts down if the corresponding FAULTBzn pin is still asserted after 10µs. When the FAULTBzn pin subsequently deasserts, the channel turns back on, honoring TON_DELAY and TON_RISE settings. Channel 5 response. 0: The channel continues operation without interruption. 1: The channel shuts down if the corresponding FAULTBzn pin is still asserted after 10µs. When the FAULTBzn pin subsequently deasserts, the channel turns back on, honoring TON_DELAY and TON_RISE settings. Channel 4 response. 0: The channel continues operation without interruption. 1: The channel shuts down if the corresponding FAULTBzn pin is still asserted after 10µs. When the FAULTBzn pin subsequently deasserts, the channel turns back on, honoring TON_DELAY and TON_RISE settings. 2978fa 39 LTC2978 Operation MFR_VINEN_OV_FAULT_RESPONSE This command register determines whether VOUT over voltage faults from a given channel cause the VIN_EN pin to be forced off. MFR_VINEN_OV_FAULT_RESPONSE Data Contents BIT(S) b[7] SYMBOL OPERATION Mfr_vinen_ov_fault_response_chan7 Response to channel 7 VOUT_OV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. b[6] Mfr_vinen_ov_fault_response_chan6 Response to channel 6 VOUT_OV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. b[5] Mfr_vinen_ov_fault_response_chan5 Response to channel 5 VOUT_OV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. b[4] Mfr_vinen_ov_fault_response_chan4 Response to channel 4 VOUT_OV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. b[3] Mfr_vinen_ov_fault_response_chan3 Response to channel 3 VOUT_OV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. b[2] Mfr_vinen_ov_fault_response_chan2 Response to channel 2 VOUT_OV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. b[1] Mfr_vinen_ov_fault_response_chan1 Response to channel 1 VOUT_OV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. b[0] Mfr_vinen_ov_fault_response_chan0 Response to channel 0 VOUT_OV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. 2978fa 40 LTC2978 Operation MFR_VINEN_UV_FAULT_RESPONSE This command register determines whether VOUT under voltage faults from a given channel cause the VIN_EN pin to be forced off. MFR_VINEN_UV_FAULT_RESPONSE Data Contents BIT(S) b[7] SYMBOL OPERATION Mfr_vinen_uv_fault_response_chan7 Response to channel 7 VOUT_UV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. b[6] Mfr_vinen_uv_fault_response_chan6 Response to channel 6 VOUT_UV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. b[5] Mfr_vinen_uv_fault_response_chan5 Response to channel 5 VOUT_UV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. b[4] Mfr_vinen_uv_fault_response_chan4 Response to channel 4 VOUT_UV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. b[3] Mfr_vinen_uv_fault_response_chan3 Response to channel 3 VOUT_UV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. b[2] Mfr_vinen_uv_fault_response_chan2 Response to channel 2 VOUT_UV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. b[1] Mfr_vinen_uv_fault_response_chan1 Response to channel 1 VOUT_UV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. b[0] Mfr_vinen_uv_fault_response_chan0 Response to channel 0 VOUT_UV_FAULT. 1 = Disable VIN_EN via fast pull-down. 0 = Leave VIN_EN as-is. 2978fa 41 LTC2978 Operation MFR_RETRY_DELAY MFR_VOUT_PEAK This command determines the retry interval when the LTC2978 is in hiccup mode in response to a fault condition. This command returns the maximum ADC measured value of the channel’s output voltage. This command is not supported for odd channels that are configured to measure current. This register is reset to zero when the LTC2978 emerges from power-on reset or when a CLEAR_FAULTS command is executed. MFR_RETRY_DELAY Data Contents BIT(S) SYMBOL OPERATION b[15:0] Mfr_retry_delay The data uses the linear format: T(Symbol) = Y • 2N Where N = b[15:11] is a 5-bit two’s complement integer and Y = b[10:0] is an 11-bit two’s complement integer This delay is counted using SHARE_CLK only. MFR_VOUT_PEAK Data Contents BIT(S) SYMBOL b[15:0] Mfr_vout_peak[15:0] The data uses the linear mode format as defined by VOUT_MODE: V(mfr_vout_peak) = Y • 2N where Y = b[15:0] is an unsigned integer and N = Vout_mode_parameter is a 5-bit two’s complement exponent that’s hardwired to –13 decimal. Delays are rounded to the nearest 200µs. Units: ms. Max delay is 13.1 sec. Units: V. MFR_RESTART_DELAY This command determines how the CONTROLn pins are adjusted before use. The time the adjusted version of the CONTROLn pin is in the off polarity is stretched by this command to be at least Mfr_restart_delay ms. CONTROLn pin transitions whose OFF time exceeds Mfr_restart_delay are not affected by this command. A value of all zeros disables this feature. MFR_RESTART_DELAY Data Contents BIT(S) SYMBOL OPERATION b[15:0] Mfr_restart_delay The data uses the linear format: T(Symbol) = Y • 2N Where N = b[15:11] is a 5-bit two’s complement integer and Y = b[10:0] is an 11-bit two’s complement integer OPERATION MFR_VIN_PEAK This command returns the maximum ADC measured value of the input voltage. The contents of this register are reset to ‘h7C00 when the LTC2978 emerges from power-on reset or when a CLEAR_FAULTS command is executed. MFR_VIN_PEAK Data Contents BIT(S) SYMBOL OPERATION b[15:0] Mfr_vin_peak[15:0] The data uses the linear format: V(Symbol) = Y • 2N where N = b[15:11] is a 5-bit two’s complement integer and Y = b[10:0] is an 11-bit two’s complement integer Units: V This delay is counted using SHARE_CLK only. MFR_TEMPERATURE_PEAK Delays are rounded to the nearest 200µs. This command returns the maximum ADC measured value of junction temperature in °C as determined by the LTC2978’s internal temperature sensor. The contents Units: ms. Max delay is 13.1 sec. 2978fa 42 LTC2978 Operation of this register are reset to ‘h7C00 when the LTC2978 emerges from power-on reset or when a CLEAR_FAULTS command is executed. MFR_TEMPERATURE_PEAK Data Contents BIT(S) SYMBOL OPERATION b[15:0] Mfr_temperature_peak[15:0] The data uses the linear format: V(Symbol) = Y • 2N Where N = b[15:11] is a 5-bit two’s complement integer and Y = b[10:0] is an 11-bit two’s complement integer Units: °C. MFR_DAC This command register returns the 10-bit value for the voltage-buffered current DAC. This register may be written when Mfr_config_dac_mode is configured for either of the two manual DAC modes. MFR_DAC Data Contents BIT(S) SYMBOL b[15:10] Reserved b[9:0] OPERATION Read only, always returns ‘h3F. Mfr_dac_direct_val Voltage-buffered current DAC code value. MFR_POWERGOOD_ASSERTION_DELAY This command register allows the user to program the delay from when the internal power good signal becomes valid until the power good output is asserted. MFR_POWERGOOD_ASSERTION_DELAY Data Contents BIT(S) SYMBOL OPERATION b[15:0] Mfr_powergood_assertion_delay The data uses the linear format: T(Symbol) = Y • 2N Where N = b[15:11] is a 5-bit two’s complement integer and Y = b[10:0] is an 11-bit two’s complement integer. MFR_WATCHDOG_T_FIRST and MFR_WATCHDOG_T The MFR_WATCHDOG_T_FIRST register allows the user to program the duration of the first watchdog timer interval following assertion of the POWER GOOD signal, assuming the POWER GOOD signal reflects the status of the watchdog timer. If assertion of POWER GOOD is not conditioned by the watchdog timer’s status, then MFR_WATCHDOG_T_FIRST applies to the first timing interval after the timer is enabled. Writing a value of 0ms to the MFR_WATCHDOG_T_FIRST register disables the watchdog timer. The MFR_WATCHDOG_T register allows the user to program watchdog time intervals subsequent to the MFR_WATCHDOG_T_FIRST timing interval. Writing a value of 0ms to the MFR_WATCHDOG_T register disables the watchdog timer. A non-zero write to MFR_WATCHDOG_T will reset the watchdog timer. MFR_WATCHDOG_T_POR and MFR_WATCHDOG_T Data Contents BIT(S) SYMBOL OPERATION b[15:0] Mfr_watchdog_t_first The data uses the linear format: Mfr_watchdog_t T(Symbol) = Y • 2N Where N = b[15:11] is a 5-bit two’s complement integer and Y = b[10:0] is an 11-bit two’s complement integer These timers operate on an internal clock independent of SHARE_CLK. Delays are rounded to the nearest 10µs for _t and 1ms for _t_first. Writing a zero value for Y to the Mfr_watchdog_t or Mfr_watchdog_t_ first registers will disable the watchdog timer. Units: ms. Max timeout is 0.6 sec for _t and 65 sec for _t_first This delay is counted using internal clock independent of SHARE_CLK. Delays are rounded to the nearest 200µs Units: ms. Max delay is 13.1 sec. 2978fa 43 LTC2978 Operation MFR_PAGE_FF_MASK b[5] The MFR_PAGE_FF_MASK command is used to select which channels respond when the global page (FF) is in use. Note that the only commands that support PAGE = ‘hFF are OPERATION and ON_OFF_CONFIG. b[4] Mfr_pads_control1 1: Logic high detected on CONTROL1 pad 0: Logic low detected on CONTROL1 pad 1: Logic high detected on CONTROL0 pad Mfr_pads_control0 0: Logic low detected on CONTROL0 pad Bit[3] used for FAULTB00 pad, bit[2] used for FAULTB01 pad, bit[1] used for FAULTB10 pad, bit[0] used for FAULTB11 pad as follows: MFR_PAGE_FF_MASK Data Contents BIT(S) SYMBOL OPERATION b[7:0] Mfr_page_ff_mask Global page response enable, per channel Each bit enables/disables the corresponding channel: 0 = ignore global page accesses 1 = fully respond to global page accesses b[3:0] Mfr_pads_faultb[3:0] 1: Logic high detected on FAULTBzn pad 0: Logic low detected on FAULTBzn pad MFR_PADS The MFR_PADS command provides read only access to slow frequency digital pads. The input values presented in bits[9:0] are before any deglitching logic. MFR_PADS_PWRGD_DRIVE Data Contents BIT(S) SYMBOL b[15] Mfr_pads_pwrgd_drive b[14] Mfr_pads_alertb_drive OPERATION 0 = PWRGD pad is being driven low by this chip 1 = PWRGD pad is not being driven low by this chip 0 = ALERTB pad is being driven low by this chip 1 = ALERTB pad is not being driven low by this chip b[13:10] Mfr_pads_faultb_drive[3.0] Bit[3] used for FAULTB00 pad, bit[2] used for FAULTB01 pad, bit[1] used for FAULTB10 pad, bit[0] used for FAULTB11 pad as follows: 0 = FAULTB pad is being driven low by this chip b[9:8] Mfr_pads_asel1[1:0] 1 = FAULTB pad is not being driven low by this chip 11: Logic high detected on ASEL1 input pad 10: ASEL1 input pad is floating 01: Reserved b[7:6] Mfr_pads_asel0[1:0] 00: Logic low detected on ASEL1 input pad 11: Logic high detected on ASEL0 input pad 10: ASEL0 input pad is floating MFR_I2C_BASE_ADDRESS The MFR_I2C_BASE_ADDRESS command determines the base value for the I2C address byte. MFR_I2C_BASE_ADDRESS Data Contents BIT(S) SYMBOL b[7] Reserved b[6:0] i2c_base_address OPERATION Read only, always returns 0. This 7-bit value determines the base value of the 7-bit I2C address. MFR_SPECIAL_ID This register contains the manufacturer ID for the LTC2978. MFR_SPECIAL_ID Data Contents BIT(S) SYMBOL OPERATION b[15:0] Mfr_special_id Read only, always returns ‘h0121 MFR_SPECIAL_LOT These paged registers contain information that identifies the user configuration that was programmed at the factory. MFR_SPECIAL_LOT Data Contents BIT(S) SYMBOL OPERATION b[7:0] Mfr_special_lot Contains the LTC default special lot number. Contact the factory to request a custom factory programmed user configuration and special lot number. 01: Reserved 00: Logic low detected on ASEL0 input pad 2978fa 44 LTC2978 Operation MFR_VOUT_DISCHARGE_THRESHOLD MFR_FAULT_LOG_CLEAR This register contains the coefficient that multiplies VOUT_COMMAND in order to determine the OFF threshold voltage for the associated output. If the output voltage has not decayed below MFR_VOUT_DISCHARGE_ THRESHOLD • VOUT_COMMAND prior to the channel being commanded to enter/re-enter the ON state, bit [7] in the STATUS_MFR_SPECIFIC register will be set and the ALERTB pin will be asserted low. In addition, the channel will not enter the ON state until the output has decayed below its OFF threshold voltage. This command initializes the EEPROM block reserved for fault logging. Any previous fault log stored in EEPROM will be erased by this operation. Other channels can be held off if a particular output has failed to discharge by using the bidirectional FAULTzn pins (refer to the MFR_FAULTBzn_RESPONSE and MFR_FAULTBzn_PROPAGATE registers). MFR_FAULT_LOG_STATUS Read only. This register is used to manage fault log events. Mfr_fault_log_status_eeprom is set after a MFR_FAULT_ LOG_STORE command or a faulted-off event triggers a transfer of the fault log from RAM to EEPROM. This bit is cleared by a MFR_FAULT_LOG_CLEAR command. BIT(S) SYMBOL OPERATION Mfr_fault_log_status_ram is set after a MFR_FAULT_ LOG_RESTORE to indicate that the data in the RAM has been restored from EEPROM and not yet read using a MFR_FAULT_LOG command. This bit is cleared by a MFR_FAULT_LOG command. b[15:0] Mfr_vout_discharge_ threshold The data uses the linear format: k = Y • 2N MFR_FAULT_LOG_STATUS Data Contents MFR_VOUT_DISCHARGE_THRESHOLD Data Contents Where N=b[15:11] is a 5-bit two’s complement integer and Y= b[10:0] is an 11-bit two’s complement integer. BIT(S) SYMBOL b[1] This command allows the user to transfer data from the RAM buffer to EEPROM. MFR_FAULT_LOG_RESTORE This command allows the user to transfer a copy of the fault-log data from the EEPROM to the RAM buffer. After a restore the RAM buffer is locked until a successful Mfr_fault_log read. Fault log RAM status: 0: The fault log RAM allows updates. Units: Dimensionless, this register contains a coefficient. MFR_FAULT_LOG_STORE Mfr_fault_log_status_ram OPERATION 1: The fault log RAM is locked until the next Mfr_fault_log read. b[0] Mfr_fault_log_status_eeprom Fault log EEPROM status: 0: The transfer of the fault log RAM to the EEPROM is enabled. 1: The transfer of the fault log RAM to the EEPROM is inhibited. 2978fa 45 LTC2978 Operation MFR_FAULT_LOG Read only. This 2048-bit data block contains a copy of the RAM buffer fault log. The RAM buffer is continuously updated after each ADC conversion as long as Mfr_fault_ log_status_ram is clear. With Mfr_config_fault_log_en = 1 and Mfr_fault_log_status_eeprom = 0, the RAM buffer is transferred to EEPROM whenever an LTC2978 fault causes a channel to latch off or a MFR_FAULT_LOG_STORE command is received. Mfr_fault_log_status_eeprom is set high after the RAM buffer is transferred to EEPROM and not cleared until a Mfr_fault_log_clear is received; even if the LTC2978 is reset or powered down. Fault log EEPROM transfers are not initiated as a result of Status_mfr_discharge, Status_mfr_fault1_in or Status_mfr_fault0_in events. During a Mfr_fault_log read, data is returned one byte at a time as defined by the following table. The fault log stores approximately 1 to 2 seconds of telemetry. MFR_FAULT_LOG Data Block Contents DATA BYTE Position_last[7:0] 0 SharedTime[7:0] SharedTime[15:8] SharedTime[23:16] SharedTime[31:24] SharedTime[39:32] SharedTime[40] Mfr_vout_peak0[7:0] Mfr_vout_peak0[15:8] Mfr_vout_min0[7:0] Mfr_vout_min0[15:8] Mfr_vout_peak1[7:0] Mfr_vout_peak1[15:8] Mfr_vout_min1[7:0] Mfr_vout_min1[15:8] Mfr_vin_peak[7:0] Mfr_vin_peak[15:8] Mfr_vin_min[7:0] 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 BLOCK READ COMMAND Position of fault log pointer when fault occurred. 41-bit share-clock counter value when fault occurred. Counter LSB is in 200µs increments. This counter is cleared at power-up or after the LTC2978 is reset MFR_FAULT_LOG Data Block Contents DATA BYTE Mfr_vin_min[15:8] 18 Mfr_vout_peak2[7:0] 19 Mfr_vout_peak2[15:8] 20 Mfr_vout_min2[7:0] 21 Mfr_vout_min2[15:8] 22 Mfr_vout_peak3[7:0] 23 Mfr_vout_peak3[15:8] 24 Mfr_vout_min3[7:0] 25 Mfr_vout_min3[15:8] 26 Mfr_temp_peak[7:0] 27 Mfr_temp_peak[15:8] 28 Mfr_ temp_min[7:0] 29 Mfr_ temp_min[15:8] 30 Mfr_vout_peak4[7:0] 31 Mfr_vout_peak4[15:8] 32 Mfr_vout_min4[7:0] 33 Mfr_vout_min4[15:8] 34 Mfr_vout_peak5[7:0] 35 Mfr_vout_peak5[15:8] 36 Mfr_vout_min5[7:0] 37 Mfr_vout_min5[15:8] 38 Mfr_vout_peak6[7:0] 39 Mfr_vout_peak6[15:8] 40 Mfr_vout_min6[7:0] 41 Mfr_vout_min6[15:8] 42 Mfr_vout_peak7[7:0] 43 Mfr_vout_peak7[15:8] 44 Mfr_vout_min7[7:0] 45 Mfr_vout_min7[15:8] 46 BLOCK READ COMMAND 47 bytes for preamble Fault_log [Position_last] Fault_log [Position_last-1] . . . Fault_log [Position_last-201] Reserved 47 48 247 248-255 Number of loops (248-47)/40 = 5 2978fa 46 LTC2978 Operation Data is logged into memory in the order shown in the following table. POSITION 32 33 34 35 36 37 38 39 When data is returned during a block read it is returned in reverse order based on the value of Position_last[7:0]. Data byte Read_vout0[7:0] is followed by Status_mfr of page 7. Example: If Position_last = 9 then the first data returned in byte position 47 of a block read is Read_vin[15:8] followed by Read_vin[7:0] followed by Status_mfr of page 1. POSITION 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 DATA Read_vout0[7:0] Read_vout0[15:8] Status_vout0 Status_mfr0 Read_vout1[7:0] Read_vout1[15:8] Status_vout1 Status_mfr1 Read_vin[7:0] Read_vin[15:8] Status_vin Reserved Read_vout2[7:0] Read_vout2[15:8] Status_vout2 Status_mfr2 Read_vout3[7:0] Read_vout3[15:8] Status_vout3 Status_mfr3 Read_temperature_1[7:0] Read_temperature_1[15:8] Status_temp Reserved Read_vout4[7:0] Read_vout4[15:8] Status_vout4 Status_mfr4 Read_vout5[7:0] Read_vout5[15:8] Status_vout5 Status_mfr5 DATA Read_vout6[7:0] Read_vout6[15:8] Status_vout6 Status_mfr6 Read_vout7[7:0] Read_vout7[15:8] Status_vout7 Status_mfr7 Total Bytes =40 MFR_COMMON This command returns status information for the shareclock pin (SCLK) and the write-protect pin (WP). MFR_COMMON Data Contents BIT(S) SYMBOL OPERATION b[7:2] Reserved Read only, always returns 0s b[1] Mfr_common_ share_clk Returns status of share-clock pin 1: Share-clock pin is being held low 0: Share-clock pin is active b[0] Mfr_common_ write_protect Returns status of write-protect pin 1: Write-protect pin is high 0: Write-protect pin is low MFR_SPARE0 This 16-bit wide registers can be used to store miscellaneous information. The contents of these registers may be stored and recalled from EEPROM using the STORE_USER_ALL and RESTORE_USER_ALL commands, respectively. MFR_SPARE2 These 16-bit wide, paged registers can be used to store miscellaneous information. The contents of these registers may be stored and recalled from EEPROM using the STORE_USER_ALL and RESTORE_USER_ALL commands, respectively. 2978fa 47 LTC2978 Operation MFR_VOUT_MIN MFR_TEMPERATURE_MIN This command returns the minimum ADC measured value of the channel’s output voltage. The contents of this register is reset to ‘hFFFF when the LTC2978 emerges from power-on reset or when a CLEAR_FAULTS command is executed. When odd channels are configured to measure current, this command is not supported. This command returns the minimum ADC measured value of junction temperature in °C as determined by the LTC2978’s internal temperature sensor. The contents of this register is reset to ‘h7BFF when the LTC2978 emerges from power-on reset or when a CLEAR_FAULTS command is executed. MFR_VOUT_MIN Data Contents MFR_TEMPERATURE_MIN Data Contents BIT(S) SYMBOL OPERATION BIT(S) b[15:0] Mfr_vout_min The data uses the linear mode format as defined by VOUT_MODE: b[15:0] Mfr_temperature_min The data uses the linear format: V(mfr_vout_min) = Y • 2N Where Y = b[15:0] is an unsigned integer and N = Vout_mode_parameter is a 5-bit two’s complement exponent that’s hardwired to a value of –13 decimal. SYMBOL OPERATION V(mfr_vin_min) = Y • 2N Where N = b[15:11] is a 5-bit two’s complement integer and Y = b[10:0] is an 11-bit two’s complement integer Units: °C. Units: V. MFR_VIN_MIN This command returns the minimum ADC measured value of the input voltage. The contents of this register is reset to ‘h7BFF when the LTC2978 emerges from power-on reset or when a CLEAR_FAULTS command is executed. Updates are disabled when unit is off for insufficient input voltage. MFR_VIN_MIN Data Contents BIT(S) SYMBOL OPERATION b[15:0] Mfr_vin_min The data uses the linear format: V(mfr_vin_min) = Y • 2N Where N = b[15:11] is a 5-bit two’s complement integer and Y = b[10:0] is an 11-bit two’s complement integer Units: V. 2978fa 48 LTC2978 Operation Watchdog Other Operations A non-zero write to the MFR_WATCHDOG_T register will reset the watchdog timer. Low-to-high transitions on the WDI pin also reset the watchdog timer. If the timer expires, ALERTB is asserted and the PWRGD output is optionally deasserted and then reasserted after MFR_PWRGD_ASSERTION_DELAY ms. Writing 0 to either the MFR_WATCHDOG_T or MFR_WATCHDOG_T_FIRST registers will disable the timer. Clock Sharing Reset Holding the WDI pin low for more than tRESETB will cause the LTC2978 to enter the power-on reset state. Following the subsequent rising-edge of the WDI pin, the LTC2978 will execute its power-on sequence per the user configuration stored in EEPROM. Multiple LTC2978s can synchronize their clocks in an application by connecting together the open-drain SHARE_CLK input/outputs to a pull-up resistor as a wired AND. In this case the fastest clock will take over and synchronize all LTC2978s. The LTC2978 can be configured to respond to the SHARE_CLK pin being held low by disabling all channels after a brief de-glitch period. When the SHARE_CLK pin is allowed to rise, the LTC2978 will respond by beginning a soft-start sequence. The LTC2978 can be configured to hold SHARE_CLK low when the unit is off for insufficient input voltage by writing b[3] = 1 “mfr_config_vin_share_enable” of the MFR_CONFIG_ALL register. Write-Protect Pin The WP pin allows the user to write-protect the LTC2978’s configuration registers. The WP pin is active high, and when asserted it overrides the WRITE_PROTECT command register. All registers are write-protected by the WP pin except for PAGE, OPERATION, CLEAR_FAULTS, MFR_PAGE_FF_MASK and STORE_USER_ALL. 2978fa 49 LTC2978 Applications Information LTC2978 Overview Some examples of typical ON/OFF configurations are: The LTC2978 is a power management IC that is capable of sequencing, margining, trimming, OV/UV supervision, providing fault management, and voltage read back for eight DC/DC converters. Input voltage and temperature read back is also available. Odd numbered channels can be configured to read back sense resistor voltages. Multiple LTC2978s can be synchronized to operate in unison using the SHARE_CLK, FAULTB and CONTROL pins. The LTC2978 utilizes a PMBus compliant interface and command set. 1.A DC/DC may be configured to turn on anytime VIN exceeds VIN_ON. Setting Command Register Values The command register settings described herein are for the purpose of understanding and software development in a host processor. In actual practice, the LTC2978 can be completely configured for standalone operation with the LTC DC590B dongle and software GUI using intuitive menu driven objects. Command Units On or Off Three control parameters determine how a particular channel is turned on and off. The CONTROLn pins, the OPERATION command and the value of the input voltage measured at the VIN_SNS pin (VIN). In all cases, VIN must exceed VIN_ON in order to enable a start. When VIN drops below VIN_OFF , an immediate shutdown of all channels will result. Refer to the OPERATION section in the data sheet for a detailed description of the ON_OFF_CONFIG command. 2. A DC/DC may be configured to turn on only when it receives an OPERATION command. 3. A DC/DC may be configured to turn on only via the CONTROL pin. 4. A DC/DC may be configured to turn on only when it receives an OPERATION command and the CONTROL pin is asserted. On Sequencing The TON_DELAY command sets the amount of time that a channel will wait following the start of an ON sequence before its VOUT_ENn pin will enable a DC/DC converter. Once the DC/DC converter has been enabled, the TON_RISE command determines the amount of time the LTC2978 waits before the VDACPn output is soft-connected and the DC/DC converter output is servoed to VOUT_COMMAND volts. The TON_MAX_FAULT_LIMIT command determines the amount of time after the DC/DC converter has been enabled that an undervoltage condition will be tolerated before a fault occurs. If a TON_MAX_FAULT occurs, the channel can be configured to disable the DC/DC converter and propagate the fault to other channels using the bidirectional FAULTBzn pins. Figure 11 shows a typical onsequence using the CONTROL pin. VCONTROL VOUT_EN VOUT_0V_FAULT_LIMIT DAC SOFT-CONNECTS AND BEGINS ADJUSTING OUTPUT VOUT_COMMAND VDC_NOM VOUT_UV_FAULT_LIMIT VOUT 2978 F11 TON_DELAY TON_RISE TON_MAX_FAULT_LIMIT Figure 11. Typical On Sequence Using Control Pin 2978fa 50 LTC2978 APPLICATIONS INFORMATION ON State Operation Once a channel has reached the ON state, the OPERATION command can be used to command the DC/DC converter’s output to margin high, margin low, or return to a nominal output voltage indicated by VOUT_COMMAND. The user also has the option of configuring a channel to continuously trim the output of the DC/DC converter to the VOUT_COMMAND voltage, or the channel’s VDACPn output can be placed in a high impedance state thus allowing the DC/DC converter output voltage to go to its nominal value, VDCn (NOM). Refer to the MFR_CONFIG command for details on how to configure the output voltage servo. Off Sequencing An off sequence is initiated using the CONTROLn pin or the OPERATION command. The TOFF_DELAY command determines the amount of time that elapses from the beginning of the off sequence until each channel’s VOUT_EN pin is pulled low thus disabling its DC/DC converter. VOUT Off Threshold Voltage The MFR_VOUT_DISCHARGE_THRESHOLD command register allows the user to specify the OFF threshold that the output voltage must decay below before the channel can enter/re-enter the ON state. The OFF threshold voltage is specified by multiplying MFR_VOUT_DISCHARGE_THRESHOLD and VOUT_COMMAND. In the event that an output voltage has not decayed below its OFF threshold before attempting to enter the ON state, the channel will continue to be held off, the appropriate bit is set in the STATUS_MFR_SPECIFIC register, and the ALERTB pin will be asserted low. When the output voltage has decayed below its OFF threshold, the channel can enter the ON state. Automatic Restart via MFR_RESTART_DELAY Command If the CONTROLn pin is toggled quickly (>10µs deglitch), an automatic restart sequence can be triggered using the MFR_RESTART_DELAY command for the channels enabled by the CONTROLn pin (see Figure 12). VOUT OV/UV Faults The high speed voltage supervisor OV and UV fault thresholds are configured using the VOUT_OV_FAULT_LIMIT and VOUT_UV_FAULT_LIMIT commands, respectively. The VOUT_UV_FAULT_RESPONSE and VOUT_UV_FAULT_ RESPONSE commands determine the response to an OV/UV fault. Fault responses can range from disabling the DC/DC converter immediately, waiting to see if the fault condition persists for some interval before disabling the DC/DC converter, or allowing the DC/DC converter to continue operating in spite of the fault. If a DC/DC converter is disabled, the LTC2978 can be configured to retry or latch-off. The retry interval is specified using the MFR_RETRY_DELAY command. Latched faults are reset by toggling the CONTROLn pin, using the OPERATION command, or removing and reapplying the bias voltage (VIN_SNS pin). All fault and warning conditions result in the ALERTB pin being asserted low and the corresponding bits being set in the status registers. The CLEAR_FAULTS command resets the contents of the status registers and deasserts the ALERTB output. CONTROL PIN BOUNCE VCONTROL VOUT_END 2978 F012 TOFF_DELAY0 MFR_RESTART_DELAY TON_DELAY0 Figure 12. Off Sequence with Automatic Restart 2978fa 51 LTC2978 APPLICATIONS INFORMATION VOUT OV/UV Warnings Multichannel Fault Management OV and UV warning threshold voltages are processed by the LTC2978’s ADC. These thresholds are set by the VOUT_OV_WARN_LIMIT and VOUT_UV_WARN_LIMIT commands. If a warning occurs, the corresponding bits are set in the status registers and the ALERTB output is asserted low. Note that a warning will never cause a VOUT_ENn output to disable a DC/DC converter. Multichannel fault management is handled using the bidirectional FAULTBzn pins. The “z” designates the fault zone which is either 0 or 1. There are two fault zones in the LTC2978. Each zone contains 4-channels. Figure 13 illustrates the connections between channels and the FAULTBzn pins. Configuring the VIN_EN Output The VIN_EN output may be used to disable the intermediate bus voltage in the event of an output OV or UV fault. Use the MFR_VINEN_OV_FAULT_RESPONSE and MFR_VINEN_UV_FAULT_RESPONSE registers to configure the VIN_EN pin to assert low in response to VOUT_OV/UV fault conditions. The VIN_EN output will stop pulling low when the LTC2978 is commanded to re-enter the ON state following a faulted-off condition. A charge-pumped 5µA pull-up to 12V is also available on the VIN_EN output. Refer to the MFR_CONFIG_ALL register description in the OPERATION section for more information. Figure 23 shows an application circuit where the VIN_EN output is used to trigger a SCR crowbar on the intermediate bus in order to protect the DC/DC converter’s load from a catastrophic fault such as a stuck top gate. • The MFR_FAULTBz0_PROPAGATE command acts like a programmable switch that allows faulted-off conditions from a particular channel (PAGE) to propagate to either FAULTBzn output in that channel’s zone. The MFR_FAULTBzn_RESPONSE command controls similar switches on the inputs to each channel that allow any channel to shut down in response to any combination of the FAULTBzn pins within a zone. Channels responding to a FAULTBzn pin pulling low will attempt a new start sequence when the FAULTBzn pin in question is released by the faulted channel. • To establish dependencies across fault zones, tie the fault pins together, e.g., FAULTB01 to FAULTB10. Any channel can depend on any other. To disable all channels in response to any channel faulting off, short all the FAULTBzn pins together, and set MFR_FAULTBzn_ PROPAGATE = ‘h01 and MFR_FAULTBzn_RESPONSE = ‘h0F for all channels. • A FAULTBzn pin can also be asserted low by an external driver in order to initiate an immediate off-sequence after a 10µs deglitch delay. 2978fa 52 LTC2978 APPLICATIONS INFORMATION MFR_FAULTB00_RESPONSE, PAGE = 0 MFR_FAULTB01_RESPONSE, PAGE = 0 MFR_FAULTB00_PROPAGATE, PAGE = 0 CHANNEL 0 EVENT PROCESSOR PAGE = 0 MFR_FAULTB00_RESPONSE, PAGE = 1 MFR_FAULTB01_RESPONSE, PAGE = 1 CHANNEL 1 EVENT PROCESSOR PAGE = 1 MFR_FAULTB01_PROPAGATE, PAGE = 1 MFR_FAULTB00_PROPAGATE, PAGE = 2 CHANNEL 2 EVENT PROCESSOR PAGE = 2 MFR_FAULTB00_RESPONSE, PAGE = 3 MFR_FAULTB01_RESPONSE, PAGE = 3 FAULTB00 MFR_FAULTB00_PROPAGATE, PAGE = 1 MFR_FAULTB00_RESPONSE, PAGE = 2 MFR_FAULTB01_RESPONSE, PAGE = 2 MFR_FAULTB01_PROPAGATE, PAGE = 0 FAULTB01 MFR_FAULTB01_PROPAGATE, PAGE = 2 MFR_FAULTB00_PROPAGATE, PAGE = 3 CHANNEL 3 EVENT PROCESSOR PAGE = 3 MFR_FAULTB01_PROPAGATE, PAGE = 3 ZONE 0 ZONE 0 ZONE 1 ZONE 1 MFR_FAULTB10_RESPONSE, PAGE = 4 MFR_FAULTB11_RESPONSE, PAGE = 4 MFR_FAULTB10_PROPAGATE, PAGE = 4 CHANNEL 4 EVENT PROCESSOR PAGE = 4 MFR_FAULTB10_RESPONSE, PAGE = 5 MFR_FAULTB11_RESPONSE, PAGE = 5 CHANNEL 5 EVENT PROCESSOR PAGE = 5 MFR_FAULTB11_PROPAGATE, PAGE = 5 MFR_FAULTB10_PROPAGATE, PAGE = 6 CHANNEL 6 EVENT PROCESSOR PAGE = 6 MFR_FAULTB10_RESPONSE, PAGE = 7 MFR_FAULTB11_RESPONSE, PAGE = 7 FAULTB10 MFR_FAULTB10_PROPAGATE, PAGE = 5 MFR_FAULTB10_RESPONSE, PAGE = 6 MFR_FAULTB11_RESPONSE, PAGE = 6 MFR_FAULTB11_PROPAGATE, PAGE = 4 FAULTB11 MFR_FAULTB11_PROPAGATE, PAGE = 6 MFR_FAULTB10_PROPAGATE, PAGE = 7 CHANNEL 7 EVENT PROCESSOR PAGE = 7 MFR_FAULTB11_PROPAGATE, PAGE = 7 2978 F13 Figure 13. Channel Fault Management Block Diagram 2978fa 53 LTC2978 APPLICATIONS INFORMATION Interconnect Between Multiple LTC2978s Figure 14 shows how to interconnect the pins in a typical multi-LTC2978 array. • All VIN_SNS lines should be tied together in a star type connection at the point where VIN is to be sensed. This will minimize timing errors for the case where the ON_OFF_CONFIG is configured to start the LTC2978 based on VIN and ignore the CONTROLn line and the OPERATION command. In multi-part applications that are sensitive to timing errors, it is recommended that the Vin_share_enable bit of the MFR_CONFIG_ALL register be set high in order to allow SHARE_CLK to synchronize on/off sequencing in response to the VIN_ON and VIN_OFF thresholds. • Connecting all VIN_EN lines together will allow an overvoltage (OV) fault on any DC/DC converter’s output in the array to shut off a common input switch. • ALERTB is typically one line in an array of PMBus converters. The LTC2978 allows a rich combination of faults and warnings to be propagated to the ALERTB pin. • WDI/RESET can be used to put the LTC2978 in the power-on reset state. Pull WDI/RESET low for at least tRESETB to enter this state. • The FAULTBzn lines can be connected together to create fault dependencies. Figure 14 shows a configuration where a fault on any FAULTBzn will pull all others low. This is useful for arrays where it is desired to abort a startup sequence in the event any channel does not come up (see Figure 15). • PWRGD reflects the status of the outputs that are mapped to it by the MFR_PWRGD_EN command. Figure 14 shows all the PWRGD pins connected together, but any combination may be used. TO VIN OF DC/DCs TO HOST CONTROLLER LTC2978 1 VIN_SNS VIN_EN SDA SCL ALERTB CONTROL0 CONTROL1 WDI/RESET FAULTB00 FAULTB01 FAULTB10 FAULTB11 SHARE_CLK PWRGD GND TO INPUT SWITCH LTC2978 #n VIN_SNS VIN_EN SDA SCL ALERTB CONTROL0 CONTROL1 WDI/RESET FAULTB00 FAULTB01 FAULTB10 FAULTB11 SHARE_CLK PWRGD GND TO OTHER LTC2978s–10k EQUIV PULL-UP RECOMMENDED ON EACH LINE EXCEPT SHARE_CLK (USE 5.49k) 2978 F14 Figure 14. Typical Connections Between Multiple LTC2978s 2978fa 54 LTC2978 APPLICATIONS INFORMATION Trimming and Margining DC/DC Converters with External Feedback Resistors is developed between the VDACP0 and VDACM0 pins by the closed-loop servo algorithm. VDACM0 is Kelvin connected to the point-of-load GND in order to minimize the effects of load induced grounding errors. The VDACP0 output is connected to the DC/DC converter’s feedback node through resistor R30. Figure 16 shows a typical application circuit for trimming/margining a power supply with an external feedback network. The VSENSEP0 and VSENSEM0 differential inputs sense the load voltage directly, and a correction voltage VCONTROLn VOUT0 TON_DELAY0 VOUT1 TON_DELAY1 VOUT2 TON_DELAY2 • • • VOUTn • • • TON_DELAYn BUSSED VFAULTBzn PINS 2978 F15 TON_MAX_FAULT1 Figure 15. Aborted On Sequence Due to Channel 1 Short VIN 4.5V < VIBUS < 15V 0.1µF VIN VPWR VIN_SNS VOUT VDACP0 VDD33 VDD33 VDD25 R30 VSENSEP0 LTC2978* DC/DC CONVERTER VFB LOAD VDACM0 0.1µF R20 R10 VSENSEM0 SGND VOUT_EN0 RUN/SS GND 2978 F16 GND *SOME DETAILS OMITTED FOR CLARITY ONLY ONE OF EIGHT CHANNELS SHOWN Figure 16. Application Circuit for DC/DC Converters with External Feedback Resistors 2978fa 55 LTC2978 APPLICATIONS INFORMATION 4-Step Resistor Selection Procedure for DC/DC Converters with External Feedback Resistors The following 4-step procedure should be used to calculate the resistor values required for the application circuit shown in Figure 16. 1. Assume values for feedback resistor R20 and the nominal DC/DC converter output voltage VDC0(NOM), and solve for R10. VDC0(NOM) is the output voltage of the DC/DC converter when the LTC2978’s VDACP0 pin is in a high impedance state. R10 is a function of R20, VDC0(NOM), the voltage at the feedback node (VFB) when the loop is in regulation, and the feedback node’s input current (IFB). R20 • VFB0 R10 = VDC(NOM) – IFB0 • R20 – VFB (1) 2. Solve for the value of R30 that yields the maximum required DC/DC converter output voltage VDC0(MAX). When VDACP0 is at 0V, the output of the DC/DC converter is at its maximum voltage. R30 ≤ R20 • VFB VDC(MAX ) – VDC(NOM) (2) 3. Solve for the minimum value of VDACP0 that’s needed to yield the minimum required DC/DC converter output voltage VDC0(MIN). The voltage-buffered current DAC has two full-scale settings, 1.33V ±3.7% and 2.7V ±3.7%. In order to select the appropriate full-scale setting, calculate the maximum required VDAC0P output voltage: ( ) VDACP0 > VDC(NOM) – VDC(MIN) • R30 + VFB R20 (3) 4. Recalculate the minimum, nominal, and maximum DC/DC converter output voltages and the resulting margining resolution. VDC(NOM) = VFB • 1 + R20 + IFB • R20 R10 ( (4) ) R20 • VDACP0(F / S) – VFB (5) R30 R20 VDC0(MAX ) = VDC(NOM) + •V (6) R30 FB R20 • VDACP0(F / S) VRES = R30 V/DAC LSB (7) 1024 VDC0(MIN) = VDC0(NOM) – 2978fa 56 LTC2978 APPLICATIONS INFORMATION Trimming and Margining DC/DC Converters with a TRIM Pin Figure 17 illustrates a typical application circuit for trimming/margining the output voltage of a DC/DC converter with a TRIM Pin. The LTC2978’s VDACPn pin connects to the TRIM pin through resistor R30, and the VDACM0 pin is connected to the converter’s point-of-load ground. DC/DC converters with a TRIM pin are typically margined high or low by connecting an external resistor between the TRIM pin and either the VSENSEP or VSENSEM pin. The relationships between these resistors and the ∆% change in the output voltage of the DC/DC converter are typically expressed as: RTRIM _ DOWN = RTRIM • 50 – RTRIM ∆DOWN % ) The following 2-step procedure should be used to calculate the resistor value for R30 and the required full-scale DAC voltage (refer to Figure 17). 1. Solve for R30: 50 – ∆DOWN % R30 ≤ RTRIM • ∆DOWN % ∆ % VDACP0 ≥ 1+ UP •V ∆DOWN % REF RTRIM _ UP = ( 2-Step Resistor and DAC Full-Scale Voltage Selection Procedure for DC/DC Converters with a TRIM Pin (10) 2. Calculate the maximum required output voltage for VDACP0: (8) V • 100 + ∆UP % 50 RTRIM • DC – – 1 ∆UP % 2 • VREF • ∆UP % ∆UP% and ∆DOWN% denote the percentage change in the converter’s output voltage when margining up or down, respectively. (9) (11) where RTRIM is the resistance looking into the TRIM pin, VREF is the TRIM pin’s open-circuit output voltage and VDC is the DC/DC converter’s nominal output voltage. VIN 4.5V < VIBUS < 15V 0.1µF VIN VPWR VIN_SNS VDD33 VSENSEP0 R30 VDACP0 VDD33 VDD25 LTC2978* GND TRIM VSENSE+ LOAD VDACM0 0.1µF VOUT+ DC/DC CONVERTER VSENSEM0 VSENSE– VOUT_EN0 ON/OFFB GND 2978 F17 *SOME DETAILS OMITTED FOR CLARITY ONLY ONE OF EIGHT CHANNELS SHOWN Figure 17. Application Circuit for DC/DC Converters with Trim Pin 2978fa 57 LTC2978 APPLICATIONS INFORMATION Measuring Current differential mode noise from the inductor of the switching DC/DC converter. The filter to the ADC is placed directly across the inductor or a sense resistor in series with the inductor. Note that the + input to the ADC must be limited to <6V above ground. Select RCM and CCM such that the corner frequency is ≤1/10 the DC/DC converter switching frequency and ≤1/10 of the internal 62.5kHz clock of the LTC2978’s ∆Σ ADC. This will assure that the DC value at the (+) input to the ADC will be equal to the output voltage with small ripple. Good values are RCM = 100Ω, CCM ≥ 1µF. Keep RCM ≤ 100Ω to minimize gain errors due to ADC input resistance. Odd numbered ADC channels may be used to measure supply current. Set the ADC to high resolution mode to configure for current measuring and improve sensitivity. Note that no OV or UV faults or warnings are reported in this mode, but telemetry is available from the READ_VOUT command using the 11-bit signed mantissa plus 5-bit signed exponent linear data format. Set the MFR_CONFIG bit b[9] = 1 in order to enable high res mode. Note: Any channel configured for ADC high res mode should be permanently commanded off, i.e., OPERATION register = ‘h00 (this is the factory default EEPROM value). The VOUT_ENn will assert low in this mode and cannot be used to control a DC/DC. The VDACPn output is also unavailable. Many switching regulator control ICs derive AC inductor current information from an RC network such as the one formed by R1, C1, R2 and C2. The proper placement of the balanced common mode filter for the ADC input is also shown in Figure 18. A circuit for measuring current is shown in Figure 18. The balanced filter, RCM, CCM, rejects common mode and RCM LTC2978 CCM RCM L + CCM + – ADC DCR – LOAD CURRENT C1 R1 TO CONTROLLER IC + – R2 C2 2978 F18 Figure 18. DCR Current Sensing Circuits 2978fa 58 LTC2978 APPLICATIONS INFORMATION Antialiasing Filter Considerations Extremely noisy environments may require an antialiasing filter on the input to the LTC2978’s ADC. The R-C circuit shown in Figure 19 is adequate for most situations. Keep R40 = R50 ≤ 200Ω to minimize ADC gain errors, and select a value for capacitors C10 and C20 that doesn’t add too much additional response time to the OV/UV supervisor, e.g. τ ≅ 10µs (R = 100Ω, C = 0.10µF). VIN 4.5V < VIBUS < 15V 0.1µF VIN VPWR VIN_SNS VOUT VDACP0 VDD33 VDD33 VDD25 VSENSEP0 LTC2978* VSENSEM0 0.1µF C10 R40 C20 R50 R30 R20 VFB LOAD R10 VDACM0 SGND VOUT_EN0 GND DC/DC CONVERTER *SOME DETAILS OMITTED FOR CLARITY ONLY ONE OF EIGHT CHANNELS SHOWN RUN/SS GND 2978 F09 Figure 19. Antialiasing Filter on VSENSE Lines 2978fa 59 LTC2978 APPLICATIONS INFORMATION Dongle Connections Figure 20 illustrates the application schematic for powering and programming one or more LTC2978’s from the LTC PMBus controller in the absence of system power. Because of the controller’s limited current sourcing capability, only TP0101K-SSOT23 SYSTEM 3.3V the LTC2978’s and the I2C pull-up resistors should be powered from the ORed 3.3V supply. In addition, any device sharing I2C bus connections with the LTC2978 should not have body diodes between the SDA/SCL pins and its VDD node because this will interfere with bus communication in the absence of system power. IDEAL DIODE OR’d 3.3V 0.1µF LTC4412 VIN SENSE 0.1µF VPWR VDD33 VDD33 VDD25 GND GATE CTL LTC2978 STAT PIN CONNECTIONS OMITTED FOR CLARITY ISOLATED 3.3V LTC CONTROLLER HEADER SDA SDA SCL SCL SHARE_CLK TO/FROM OTHER LTC2978s WP GND 2978 F10 NOTE: LTC CONTROLLER I2C CONNECTONS ARE OPTO-ISOLATED ISOLATED 3.3V FROM CONTROLLER CAN BE BACK DRIVEN AND WILL ONLY DRAW < 10µA ISOLATED 3.3V CURRENT LIMIT = 100mA Figure 20. LTC Controller Connections for Powering and Communicating with the LTC2978 2978fa 60 LTC2978 APPLICATIONS INFORMATION PCB Assembly and Layout Suggestions Bypass Capacitor Placement The LTC2978 requires 0.1µF bypass capacitors between the VDD33 pins and GND, the VDD25 pin and GND, and the REFP pin and REFM pin. If the chip is being powered from the VPWR input, then that pin should also be bypassed to GND by a 0.1µF capacitor. In order to be effective, these capacitors should be made of high quality ceramic dielectric such as X5R or X7R and be placed as close to the chip as possible. Exposed Pad Stencil Design The LTC2978’s package is thermally and electrically efficient. This is enabled by the exposed die attach pad on the under side of the package which must be soldered down to the PCB or mother board substrate. It is a good practice to minimize the presence of voids within the exposed pad inter-connection. Total elimination of voids is difficult, but the design of the exposed pad stencil is key. Figure 21 shows a suggested screen print pattern. The proposed stencil design enables out-gassing of the solder paste during reflow as well as regulating the finished solder thickness. PC Board Layout Mechanical stress on a PC board and soldering-induced stress can cause the LTC2978’s reference voltage and voltage drift to shift. A simple way to reduce these stressrelated shifts is to mount the IC near the short edge of the PC board, or in a corner. The board edge acts as a stress boundary, or a region where the flexure of the board is minimal. 2978 F11 Figure 21. Suggested Screen Pattern for Die Attach Pad 2978fa 61 LTC2978 Typical Application 0.1µF 42 6 VIN VOUT 45 47 R32 R22 DC/DC CONVERTER VFB LOAD R12 RUN/SS SGND GND 48 46 7 51 49 50 52 IN 8 VIN_SNS ASEL0 ASEL1 VPWR VDD33 VDD25 WP GND REFP REFM VDACP7 VSENSEP7 VSENSEM0 VSENSEM7 VDACM0 VDACM7 VOUT_EN0 VOUT_EN7 VDACP1 VDACP6 VSENSEP1 VSENSEP6 VSENSEM1 VSENSEM6 VDACM1 VDACM6 VOUT_EN1 VOUT_EN6 LTC2978 VDACP2 VDACP5 VSENSEP2 VSENSEP5 VSENSEM2 VSENSEM5 VDACM2 VDACM5 VOUT_EN2 VOUT_EN5 VDACP3 VDACP4 VSENSEP3 VSENSEP4 VSENSEM3 VSENSEM4 VDACM3 OUT INTERMEDIATE BUS CONVERTER 15 VOUT_EN3 13 EN 3.3V 24 25 26 27 22 28 29 30 31 32 21 VDACM4 WDI/RESETB 44 33 PWRGD 43 34 CONTROL1 41 16 CONTROL0 5 17 ALERTB RUN/SS SGND GND 18 SCL 39 19 SDA 38 20 SHARE_CLK LOAD R10 VSENSEP0 65 FAULTB11 VFB VDACP0 FAULTB10 37 36? 35 FAULTB01 40 R30 R20 FAULTB00 VOUT DC/DC CONVERTER VIN_EN VIN NC 14 3.3V 0.1µF VDD33 0.1µF VOUT_EN4 VOUT 61 3 4 R37 R27 VIN DC/DC CONVERTER VFB LOAD R17 62 SGND RUN/SS GND 12 VOUT 60 1 2 R36 R26 VIN DC/DC CONVERTER VFB LOAD R16 59 SGND RUN/SS GND 11 VOUT 57 63 64 R35 R25 VIN DC/DC CONVERTER VFB LOAD R15 58 SGND RUN/SS GND 10 VOUT 56 53 54 55 R34 R24 VIN DC/DC CONVERTER VFB LOAD R14 SGND RUN/SS GND 9 2978 F12 23 10k 10k 5.49k 10k 3.3V TO/FROM OTHER LTC2978s AND MICROCONTROLLER Figure 22. LTC2978 Application Circuit with 3.3V Chip Power 2978fa 62 LTC2978 Package Description UP Package 64-Lead Plastic QFN (9mm × 9mm) (Reference LTC DWG # 05-08-1705 Rev C) 0.70 p0.05 7.15 p0.05 7.50 REF 8.10 p0.05 9.50 p0.05 (4 SIDES) 7.15 p0.05 PACKAGE OUTLINE 0.25 p0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 9 .00 p 0.10 (4 SIDES) 0.75 p 0.05 R = 0.10 TYP R = 0.115 TYP 63 64 0.40 p 0.10 PIN 1 TOP MARK (SEE NOTE 5) 1 2 PIN 1 CHAMFER C = 0.35 7.50 REF (4-SIDES) 7.15 p 0.10 7.15 p 0.10 (UP64) QFN 0406 REV C 0.200 REF 0.00 – 0.05 NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE MO-220 VARIATION WNJR-5 2. ALL DIMENSIONS ARE IN MILLIMETERS 3. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE, IF PRESENT 4. EXPOSED PAD SHALL BE SOLDER PLATED 5. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 6. DRAWING NOT TO SCALE 0.25 p 0.05 0.50 BSC BOTTOM VIEW—EXPOSED PAD 2978fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 63 LTC2978 Typical Application RSENSE 0.007Ω VIN <15V Q1 Si4894BDY VIN CBYPASS VIN_SNS VPWR VCC GATE LTC4210-3 24.3k 10k SENSE ON TIMER GND 100Ω VOUT VDACP0 DC/DC CONVERTER VSENSEP0 0.1µF LTC2978* 68Ω VFB LOAD VDACM0 0.01µF 0.22µF VSENSEM0 SGND VOUT_EN0 RUN/SS GND 10k 0.01µF 2907 4.99k 2978 F23 MCR12DC 220Ω 0.1µF BAT54 REFP VIN_EN REFM VDD33 VDD33 VDD25 GND 0.1µF *SOME DETAILS OMITTED FOR CLARITY ONLY ONE OF EIGHT CHANNELS SHOWN 0.1µF Figure 23. LTC2978 Application Circuit with Crowbar Protection on Intermediate Bus Related Parts PART NUMBER DESCRIPTION COMMENTS LTC2970 Dual I2C Power Supply Monitor and Margining Controller 14-Bit ∆Σ ADC with < ±0.5% TUE, Dual 8-Bit IDACs with 1x Voltage Buffers LTC4151 High Voltage I2C Current and Voltage Monitor 7V to 80V, 12-Bit Resolution LTC4210-3 Hot Swap™ Controller in 6-Lead SOT-23 Package Adjustable Analog Current Limit with Circuit Breaker, Fast Response Limits Peak Fault Current LTC4412 Low Loss PowerPath™ Controller in ThinSOT™ Replaces Power Supply ORing Diodes, Minimal External Components, Automatic Switching Between DC Sources, Simplifies Load Sharing with Multiple Batteries, Low Quiescent Current: 11µA LTM®4601 8A, Low VIN DC/DC µModule® with PLL, Output Tracking and Margining Complete Switch Mode Power Supply, 4.5V to 20V Input Voltage, 0.6V to 5V Output Voltage, PLL Frequency Synchronization, ±1.5% Regulation LTM4608 8A, Low VIN DC/DC µModule with Tracking, Margining, Multiphase and Frequency Synchronization Complete Switch Mode Power Supply, 2.7V to 5.5V Input Voltage, 0.6V to 5V Output Voltage, Onboard Frequency Synchronization, ±1.5% Regulation µModule is a registered trademark of Linear Technology Corporation. PowerPath, ThinSOT and Hot Swap are trademarks of Linear Technology Corporation. 2978fa 64 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LT 0909 REV A • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2009