MITSUBISHI IGBT MODULES CM100BU-12H HIGH POWER SWITCHING USE INSULATED TYPE CM100BU-12H ● IC ................................................................... 100A ● VCES .......................................................... 600V ● Insulated Type ● 4-elements in a pack ● UL Recognized Yellow Card No. E80276 File No. E80271 APPLICATION UPS, Welders OUTLINE DRAWING & CIRCUIT DIAGRAM Dimensions in mm 72 4–φ5.5 MOUNTING HOLES 11 4 P 18.7 N P +1.0 29 –0.5 1.25 55 ±0.25 20 17.5 19.1 11 14.4 EuN CM GvN G E G 4–M4NUTS TC measured point 10 19.1 10.5 20 GvN EuN EvN CIRCUIT DIAGRAM 28 0.5 TC measured point +1.0 29 –0.5 17.5 15 TAB #110. t=0.5 26 8.1 5 GuN EvN 10 11 15 E V U V 16 EvP U GuN EuP GvP GvP EvP N E 56 G 39.3 E 1.25 91 74 ±0.25 GuP G GuP EuP LABEL 41 Feb. 2009 1 MITSUBISHI IGBT MODULES CM100BU-12H HIGH POWER SWITCHING USE INSULATED TYPE MAXIMUM RATINGS Symbol VCES VGES IC ICM IE (Note 2) IEM (Note 2) PC (Note 3) Tj Tstg Viso (Tj = 25°C, unless otherwise specified) Item Collector current Emitter current Maximum collector dissipation Junction temperature Storage temperature Isolation voltage — Mounting torque — Weight ELECTRICAL CHARACTERISTICS Symbol Conditions Collector-emitter voltage Gate-emitter voltage Note 1. 2. 3. 4. 5. 6. (Note 1) Ratings Unit 600 ±20 100 200 100 200 400 –40 ~ +150 –40 ~ +125 2500 1.3 ~ 1.7 2.5 ~ 3.5 390 V V A A A A W °C °C Vrms N·m N·m g (Tj = 25°C, unless otherwise specified) Collector cutoff current Gate-emitter VGE(th) threshold voltage Gate-leakage current IGES Collector-emitter VCE(sat) saturation voltage Input capacitance Cies Output capacitance Coes Reverse transfer capacitance Cres QG Total gate charge td (on) Turn-on delay time tr Turn-on rise time td (off) Turn-off delay time tf Turn-off fall time V EC(Note 2) Emitter-collector voltage t rr (Note 2) Reverse recovery time Q rr (Note 2) Reverse recovery charge Rth(j-c)Q Thermal resistance (Note 5) Rth(j-c)R Contact thermal resistance (Note 1) — — Charged part to base plate, f = 60Hz, AC 1 minute Main terminals M4 screw Mounting M5 screw Typical value VCE = VCES, VGE = 0V Min — Limits Typ — Max 1 IC = 10mA, VCE = 10V 4.5 6 7.5 V — — — — — — — — — — — — — — — — — 2.4 2.6 — — — 200 — — — — — — 0.24 — — 0.5 3.0 — 8.8 4.8 1.3 — 100 250 200 300 2.6 160 — 0.31 0.7 µA nF nF nF nC ns ns ns ns V ns µC K/W K/W — 0.1 — K/W Item ICES Rth(c-f) VGE = 0V VCE = 0V TC = 25°C Pulse TC = 25°C Pulse TC = 25°C Test Conditions ±VGE = VGES, VCE = 0V IC = 100A, VGE = 15V (Note 4) Tj = 25°C Tj = 125°C VCE = 10V VGE = 0V VCC = 300V, IC = 100A, VGE = 15V VCC = 300V, IC = 100A VGE = ±15V RG = 6.3Ω Resistive load IE = 100A, VGE = 0V IE = 100A, die / dt = –200A / µs Junction to case, IGBT part (Per 1/4 module) Junction to case, FWDi part (Per 1/4 module) Case to heat sink, conductive grease applied (Per 1/4 module) (Note 6) Unit mA V Pulse width and repetition rate should be such that the device junction temperature (Tj) does not exceed Tjmax rating. IE, VEC, trr, Qrr & die/dt represent characteristics of the anti-parallel, emitter-collector free-wheel diode. Junction temperature (Tj) should not increase beyond 150°C. Pulse width and repetition rate should be such as to cause negligible temperature rise. Case temperature (TC) measured point is shown in page OUTLINE DRAWING. Typical value is measured by using thermally conductive grease of λ = 0.9[W/(m • K)]. Feb. 2009 2 MITSUBISHI IGBT MODULES CM100BU-12H HIGH POWER SWITCHING USE INSULATED TYPE PERFORMANCE CURVES TRANSFER CHARACTERISTICS (TYPICAL) OUTPUT CHARACTERISTICS (TYPICAL) 200 14 Tj=25°C VCE = 10V 13 COLLECTOR CURRENT IC (A) COLLECTOR CURRENT IC (A) 200 VGE=20 (V) 150 15 12 11 100 10 50 9 150 100 50 Tj = 25°C Tj = 125°C 8 0 2 4 6 8 0 10 4 8 12 16 20 GATE-EMITTER VOLTAGE VGE (V) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) 5 VGE = 15V Tj = 25°C Tj = 125°C 4 3 2 1 0 0 50 100 150 200 Tj = 25°C 8 6 IC = 200A 4 IC = 100A 2 IC = 40A 0 4 8 12 16 20 COLLECTOR CURRENT IC (A) GATE-EMITTER VOLTAGE VGE (V) FREE-WHEEL DIODE FORWARD CHARACTERISTICS (TYPICAL) CAPACITANCE CHARACTERISTICS (TYPICAL) 101 Tj = 25°C CAPACITANCE Cies, Coes, Cres (nF) 7 5 10 0 103 EMITTER CURRENT IE (A) 0 COLLECTOR-EMITTER VOLTAGE VCE (V) COLLECTOR-EMITTER SATURATION VOLTAGE VCE(sat) (V) COLLECTOR-EMITTER SATURATION VOLTAGE VCE(sat) (V) 0 3 2 102 7 5 3 2 7 5 Cies 3 2 100 7 5 3 2 Coes Cres 10–1 7 5 3 2 3.0 VGE = 0V 10–2 –1 10 2 3 5 7 100 2 3 5 7 101 2 3 5 7 102 EMITTER-COLLECTOR VOLTAGE VEC (V) COLLECTOR-EMITTER VOLTAGE VCE (V) 101 1.0 1.4 1.8 2.2 2.6 Feb. 2009 3 MITSUBISHI IGBT MODULES CM100BU-12H HIGH POWER SWITCHING USE INSULATED TYPE 103 3 2 td(off) 102 7 5 td(on) 3 VCC = 300V VGE = ±15V RG = 6.3Ω tr 101 7 101 2 5 7 102 3 2 3 2 5 3 3 2 2 trr 102 7 5 101 7 5 Irr 3 3 2 2 7 101 2 3 5 7 102 2 3 5 7 COLLECTOR CURRENT IC (A) EMITTER CURRENT IE (A) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT part) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi part) 10–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7 100 2 3 5 7 101 101 7 Single Pulse 5 3 TC = 25°C Per unit base = Rth(j – c) = 0.31K/ W 100 5 101 5 7 NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth(j – c) SWITCHING TIMES (ns) tf 2 NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth(j – c) REVERSE RECOVERY TIME trr (ns) Tj = 125°C 7 5 REVERSE RECOVERY CHARACTERISTICS OF FREE-WHEEL DIODE (TYPICAL) 103 102 – di /dt = 200A /µs 7 7 Tj = 25°C 7 5 3 2 3 2 10–1 10–1 10–2 10–2 10–3 10–3 10–5 2 3 5 710–4 2 3 5 7 10–3 7 5 3 2 7 5 3 2 7 5 3 2 7 5 3 2 TIME (s) REVERSE RECOVERY CURRENT Irr (A) HALF-BRIDGE SWITCHING TIME CHARACTERISTICS (TYPICAL) 100 10–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7 100 2 3 5 7 101 101 7 Single Pulse 5 3 TC = 25°C 2 100 Per unit base = Rth(j – c) = 0.7K/ W 7 5 3 2 3 2 10–1 10–1 10–2 10–2 10–3 10–3 10–5 2 3 5 710–4 2 3 5 7 10–3 7 5 3 2 7 5 3 2 7 5 3 2 7 5 3 2 TIME (s) GATE CHARGE CHARACTERISTICS (TYPICAL) GATE-EMITTER VOLTAGE VGE (V) 20 IC = 100A VCC = 200V 15 VCC = 300V 10 5 0 0 50 100 150 200 250 300 GATE CHARGE QG (nC) Feb. 2009 4