MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 D D description These devices are monolithic low-power Schottky quadruple line receivers designed to satisfy the requirements of the standard interface between data-terminal equipment and data-communication equipment as defined by TIA / EIA-232-F. A separate response-control (CONT) terminal is provided for each receiver. A resistor or a resistor and bias-voltage source can be connected between this terminal and ground to shift the input threshold levels. An external capacitor can be connected between this terminal and ground to provide input noise filtering. The SN55189 and SN55189A are characterized for operation over the full military temperature range of – 55°C to 125°C. The MC1489, MC1489A, SN75189, and SN75189A are characterized for operation from 0°C to 70°C. SN55189, SN55189A . . . J OR W PACKAGE MC1489, MC1489A, SN75189, SN75189A D, N, OR NS† PACKAGE (TOP VIEW) 1A 1CONT 1Y 2A 2CONT 2Y GND 1 14 2 13 3 12 4 11 5 10 6 9 7 8 VCC 4A 4CONT 4Y 3A 3CONT 3Y † The NS package is only available left-end taped and reeled. For SN75189, order SN75189NSR. SN55189, SN55189A . . . FK PACKAGE (TOP VIEW) 1CONT 1A NC VCC 4A D Input Resistance . . . 3 kΩ to 7 kΩ Input Signal Range . . . ± 30 V Operate From Single 5-V Supply Built-In Input Hysteresis (Double Thresholds) Response Control that Provides: Input Threshold Shifting Input Noise Filtering Meet or Exceed the Requirements of TIA / EIA-232-F and ITU Recommendation V.28 Fully Interchangeable With Motorola MC1489 and MC1489A 1Y NC 2A NC 2CONT 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 4CONT NC 4Y NC 3A 2Y GND NC 3Y 3CONT D D D D NC – No internal connection Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Motorola is a trademark of Motorola, Incorporated. Copyright 1998, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 logic symbol† 1A 1 CONT 2A 2 CONT 3A 3 CONT 1 2 4 3 1Y THRS ADJ 6 2Y 5 10 8 3Y 9 13 11 4Y 4A 4 CONT 12 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for the D, J, N, NS, and W packages. logic diagram (positive logic) A Y Response Control schematic (each receiver) VCC 9 kΩ 5 kΩ 1.66 kΩ Output Y R1 Response Control 4 kΩ Input A 10 kΩ GND R1 MC1489 SN55189 SN75189 MC1489A SN55189A SN75189A 8.4 kΩ 1.84 kΩ Resistor values shown are nominal. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 absolute maximum ratings over operating free-air temperature (unless otherwise noted)† Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±30 V Output voltage, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA: SN55189, SN55189A . . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C MC1489, MC1489A, SN75189, SN75189A . . . . . . 0°C to 70°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C Case temperature for 60 seconds, FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J or W package . . . . . . . . . . . . . . . . 300°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, N, or NS package . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values are with respect to the network ground terminal. DISSIPATION RATING TABLE PACKAGE TA ≤ 25°C POWER RATING DERATING FACTOR ABOVE TA = 25°C TA = 70°C POWER RATING TA = 125°C POWER RATING D 950 mW 7.6 mW/°C 608 mW N/A FK J‡ 1375 mW 11.0 mW/°C 880 mW 275 mW 1375 mW 11.0 mW/°C 880 mW 275 mW N 1150 mW 9.2 mW/°C 736 mW N/A NS 625 mW 4.0 mW/°C 445 mW N/A W 1000 mW 8.0 mW/°C 640 mW ‡ In the J package, SN55189 and SN55189A chips are either silver glass or alloy mounted. 200 mW recommended operating conditions MIN NOM MAX Supply voltage, VCC 4.5 5 5.5 V Input voltage, VI –25 25 V High-level output current, IOH Low-level output current, IOL Operating free-air temperature, TA 0 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 UNIT –0.5 mA 10 mA 70 °C 3 MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 electrical characteristics over operating free-air temperature range, VCC = 5 V ± 1% (unless otherwise noted) TEST FIGURE PARAMETER TEST CONDITIONS† VIT IT+ Positive-going g g input threshold voltage TA = – 55°C to 125°C TA = 25°C 1 ’89A VIT– Negative-going N ti i input i t threshold voltage 1 VOH High-level g output voltage 1 VOL Low-level output voltage IIH ’89, ’89A TA = 0°C to 70°C TA = – 55°C to 125°C TA = 25°C TA = 0°C to 70°C TA = – 55°C to 125°C VI = 0.75 V, IOH = – 0.5 mA UNIT MIN TYP‡ MAX MIN TYP‡ MAX 1 1.3 1.5 1 1.3 1.5 TA = 25°C TA = 0°C to 70°C ’89 MC1489, MC1489A SN75189 SN75189A SN55189 SN55189A 0.9 0.6 1.75 1.6 1.9 1.9 2.25 1.75 1.9 1.55 1.30 0.75 2.25 V 2.25 2.65 1.0 1.25 0.75 1.0 0.65 0.35 1.25 1.25 V 1.6 2.6 4 5 2.6 4 5 2.6 4 5 2.6 4 5 02 0.2 0 45 0.45 02 0.2 0 45 0.45 Input open, IOH = – 0.5 mA 1 VI = 3 V V, IOL = 10 mA High-level g input current 2 VI = 25 V VI = 3 V IIL Low-level input current 2 VI = – 25 V VI = – 3 V IOS Short-circuit output current 3 –3 ICC Supply current 2 VI = 5 V, Outputs open † All characteristics are measured with the response-control terminal open. ‡ All typical values are at VCC = 5 V, TA = 25°C. 20 3.6 8.3 0.43 3.6 8.3 0.43 – 3.6 – 8.3 – 0.43 – 3.6 –8.3 – 0.43 3 –3 26 V V mA mA mA 20 26 TYP MAX RL = 3.9 kΩ 25 85 RL = 390 Ω 25 50 RL = 3.9 kΩ 120 175 RL = 390 Ω 10 20 mA switching characteristics, VCC = 5 V, CL = 15 pF, TA = 25°C TEST FIGURE PARAMETER tPLH tPHL Propagation delay time, low- to high-level output tTLH tTHL Transition time, low- to high-level output 4 Propagation delay time, high- to low-level output Transition time, high- to low-level output POST OFFICE BOX 655303 4 TEST CONDITIONS • DALLAS, TEXAS 75265 MIN UNIT ns ns MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 PARAMETER MEASUREMENT INFORMATION† VCC VIT, V1 – IOH VOH Response Control Open Unless Otherwise Specified VOL RC IOL RC CC – VC +VC Figure 1. VIT + , VIT – , VOH , VOL VCC ICC (see Note A) VI IIH Open IIL Response Control Open NOTE A: ICC is tested for all four receivers simultaneously. Figure 2. IIH , IIL , ICC VCC – IOS Response Control Open Figure 3. IOS † Arrows indicate actual direction of current flow. Current into a terminal is a positive value. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 PARAMETER MEASUREMENT INFORMATION VCC Output RL Pulse Generator (see Note A) See Note C CL = 15 pF (see Note B) Response Control Open TEST CIRCUIT ≤10 ns ≤10 ns Input 10% 90% 50% 90% 50% 90% 10% 0V tPLH tPHL Output 4V VOH 50% 10% 90% 50% 10% tTHL VOL tTLH VOLTAGE WAVEFORMS NOTES: A. The pulse generator has the following characteristics: ZO = 50 Ω, tw = 500 ns. B. CL includes probe and jig capacitances. C. All diodes are 1N3064 or equivalent. Figure 4. Test Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 TYPICAL CHARACTERISTICS SN65189, SN75189 OUTPUT VOLTAGE vs INPUT VOLTAGE ÁÁÁ ÁÁÁÁ ÎÎÎÎ ÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁ ÁÁÁ ÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁ ÁÁÁ ÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ 6 V VO O – Output Voltage – V 5 4 3 VIT– 2 RC = ∞ RC = 13 kΩ VC = 5 V RC = 5 kΩ VC = 5 V VIT+ VIT+ VIT– RC = 11 kΩ VC = – 5 V VIT+ VIT– VCC = 5 V TA = 25°C See Figure 1 VIT+ VIT– 1 0 –3 –1 –2 0 1 VI – Input Voltage – V 2 3 4 5 Figure 5 ÁÁÁÁ ÁÁÁÁ 6 VO V O – Output Voltage – V SN65189A, SN75189A OUTPUT VOLTAGE vs INPUT VOLTAGE ÎÎÎÎ ÎÎÎÎ 5 ÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁ RC = ∞ RC = 5 kΩ VC = 5 V VCC = 5 V TA = 25°C See Figure 1 RC = 11 kΩ VC = – 5 V 4 3 VIT– VIT+ VIT– VIT+ VIT– VIT+ 2 1 0 –3 –2 –1 0 1 VI – Input Voltage – V 2 3 4 5 Figure 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 TYPICAL CHARACTERISTICS† INPUT THRESHOLD VOLTAGE vs SUPPLY VOLTAGE 2.4 2 2.2 1.8 2 ’89A VIT+ 1.8 1.6 ’89 VIT+ 1.4 1.2 ’89 VIT– 1 ’89A VIT– 0.8 ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ’89A VIT+ 1.6 V IT – Input Threshold Voltage – V V IT – Input Threshold Voltage – V INPUT THRESHOLD VOLTAGE vs FREE-AIR TEMPERATURE ’89 VIT– 1.4 1.2 ’89 VIT+ 1 ’89A VIT– 0.8 0.6 0.4 0.6 0.2 0.4 – 100 – 75 – 50 – 25 0 25 50 0 2 75 100 125 150 3 4 TA – Free-Air Temperature – °C ÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎ ÁÁÁÁÁ ÎÎÎÎÎ ÁÁÁÁÁ ÎÎÎÎÎ 6 6 VCC = 5 V TA = 25°C See Note A ÎÎÎÎÎ ÎÎÎÎÎ ÁÁÁÁ ÎÎÎÎÎ ÁÁÁÁ ÎÎÎÎÎ ÁÁÁÁ CC = 300 pF 3 ÁÁÁÁ ÁÁÁÁ ÁÁÁÁ ÁÁÁÁ Amplitude – V CC = 500 pF 4 3 CC = 10 pF 1 CC = 100 pF 0 10 40 100 CC = 500 pF ÁÁÁÁ ÁÁÁÁ ÎÎÎÎÎ ÁÁÁÁ ÎÎÎÎÎ ÁÁÁÁ CC = 12 pF 2 2 VCC = 5 V TA = 25°C See Note A 5 CC = 300 pF 4 CC = 100 pF 1 400 1000 4000 10000 0 10 40 100 400 4000 10000 NOTE A: Maximum amplitude of a positive-going pulse that, starting from 0 V, will not cause a change in the output level. Figure 9 Figure 10 † Data for free-air temperatures below 0°C and above 70°C are applicable to SN55189 and SN55189A circuits only. POST OFFICE BOX 655303 1000 tw – Pulse Duration – ns tw – Pulse Duration – ns NOTE A: Maximum amplitude of a positive-going pulse that, starting from 0 V, will not cause a change in the output level. 8 10 SN75189A NOISE REJECTION SN75189 NOISE REJECTION 5 9 Figure 8 Figure 7 Amplitude – V 5 6 7 8 VCC – Supply Voltage – V • DALLAS, TEXAS 75265 MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 TYPICAL CHARACTERISTICS INPUT CURRENT vs INPUT VOLTAGE 10 8 IIII – Input Current – mA 6 4 ÎÎÎÎÎ ÁÁÁÁ ÎÎÎÎÎ ÎÎÎÎÎ VCC = 5 V Control Open TA = 25°C 2 0 –2 –4 –6 –8 –10 – 25 – 20 –15 –10 – 5 0 5 10 VI – Input Voltage – V 15 20 25 Figure 11 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated