250mA SmartORTM Regulator with VAUX Switch CMPWR101 Features • • • • • • • • • • Automatic detection of VCC input supply Glitch-free output during supply transitions Built-in hysteresis during supply selection 250mA output maximum load current Fully integrated VAUX switch Overload current protection Short circuit current protection Operates from either VCC or VAUX 8-pin SOIC package RoHS compliant (lead-free) finishing Applications • • • • PCI adapter cards Network Interface Cards (NICs) Dual power systems Systems with standby capabilities Product Description The California Micro Devices’ SmartORTM CMPWR101 is a low dropout regulator that delivers up to 250mA of load current at a fixed 3.3V output. An internal threshold level (typically 4.1V) is used to prevent the regulator from being operated below dropout voltage. The device continuously monitors the input supply and will automatically disable the regulator when VCC falls below the threshold level. When the regulator is disabled, a low impedance, fully integrated switch is enabled which allows the output to be directly powered from an auxiliary 3.3V supply. When VCC is restored to a level above the select threshold, the low impedance switch is disabled and the regulator is once again enabled. All the necessary control circuitry needed to provide a smooth and automatic transition between the supplies has been incorporated. This allows VCC to be dynamically switched without loss of output voltage. An output logic signal, DRIVE, is active LOW whenever the internal regulator is disabled. The CMPWR101 is housed in a 8-pin SOIC package and is available with RoHS compliant lead-free finishing. ©2010 SCILLC. All rights reserved. June 2010 Rev. 3 Publication Order Number: CMPWR101/D CMPWR101 Typical Application Circuit Simplified Electrical Schematic PIN DESCRIPTIONS PIN(S) NAME DESCRIPTION 1 VCC VCC is the power source for the internal regulator and is monitored continuously by an internal controller circuit. Whenever VCC exceeds VCCSEL (4.25V typically), the internal regulator will be enabled and deliver a fixed 3.3V at VOUT. When VCC falls below VCCDES (4.10V typically), the regulator will be disabled. Internal loading on this pin is typically 0.6mA when the regulator is enabled, which reduces to 0.1mA whenever the regulator is disabled. If VCC falls below the voltage on the VAUX pin, the VCC loading will further reduce to only a few microamperes. During a VCC power-up or power-down sequence, there will be an effective step increase in VCC line current when the regulator is enabled/disabled. This line current transient will cause a voltage disturbance at the VCC pin. The magnitude of the disturbance will be directly proportional to the effective power supply source impedance being delivered to the VCC input. A built-in hysteresis voltage of 150mV has been incorporated to minimize any chatter during supply changeover. It is recommended that the power supply connected to the VCC input should have a source resistance of less than 0.25Ω to minimize the event of chatter during the enabling/disabling of the regulator. If the VCC pin is within a few inches of the main input filter, a capacitor may not be necessary. Otherwise an input filter capacitor in the range of 1µF to 10µF will help to lower the effective source impedance. 2-3 VAUX VAUX is the auxiliary power source. When selected, (VCC < VCCDES), the auxiliary supply is directly connected to VOUT, via the low impedance (0.3Ω typically) fully integrated switch. The internal loading on this pin is typically less than 10µA and will increase to 100µA if VCC falls below the voltage on VAUX. When VAUX = 0V, the VCCDES voltage is inhibited which prevents the regulator from being disabled. 4 GND GND is the negative reference for all voltages. The current that flows in the ground connection is very low (typically 0.6mA) and has minimal variation over all load conditions. 5 NC NC is an unconnected pin which is electrically isolated from the internal circuitry 6-7 VOUT VOUT is the regulator output voltage connection used to power the load. An output capacitor of 4.7µF is used to provide the necessary phase compensation, thereby preventing oscillation. The capacitor also helps to minimize the peak output disturbance during power supply changeover. 8 DRIVE DRIVE is a CMOS output logic signal (Active Low) referenced to the VCC supply. This output is taken low whenever the internal regulator is not enabled. This output is intended only as a control signal for external circuitry. Rev. 3 | Page 2 of 12 | www.onsemi.com CMPWR101 VCC VAUX VAUX GND 1 8 2 7 3 6 4 5 DRIVE VOUT VOUT NC 8-pin SOIC Ordering Information PART NUMBERING INFORMATION Pins Package Ordering Part Number1 Part Marking 8 Power SOIC CMPWR101R CMPWR 101R Note 1: Parts are shipped in Tape & Reel form unless otherwise specified. Specifications ABSOLUTE MAXIMUM RATINGS PARAMETER RATING UNITS +2000 V [GND - 0.5] to +6.0 [GND - 0.5] to +4.0 [GND - 0.5] to [VCC + 0.5] V V -40 to +150 °C Operating Temperature Range Ambient Junction 0 to +70 0 to +125 °C °C Power Dissipation (See Note 1) 0.5 W ESD Protection (HBM) Pin Input Voltages VCC VAUX DRIVE Storage Temperature Range Note 1: The power rating is based on a printed circuit board heat spreading capability equivalent to 2 square inches of copper connected to the GND pins. Typical multi-layer boards using power plane construction will provide this heat spreading ability without the need for additional dedicated copper area. (Please consult with factory for thermal evaluation assistance). Rev. 3 | Page 3 of 12 | www.onsemi.com CMPWR101 STANDARD OPERATING CONDITIONS PARAMETER VALUE UNITS VCC 5.0 +0.5 V VAUX 3.3 +0.3 V Ambient Operating Temperature Range 0 to +70 °C Load Current 0 to 250 mA 4.7 +20% μF CEXT Rev. 3 | Page 4 of 12 | www.onsemi.com CMPWR101 ELECTRICAL OPERATING CHARACTERISTICS (SEE NOTE 1) SYMBOL VOUT ILIM PARAMETER CONDITIONS Regulator Output Voltage 0mA < ILOAD < 250mA Regulator Current Limit MIN TYP MAX 3.135 3.300 3.465 275 VCCSEL VCC Select Voltage Regulator enabled VCCDES VCC Deselect Voltage Regulator disabled VCCHYST Hysteresis Voltage VR LOAD Load Regulation VR LINE Line Regulation xx See Note 2 VCC=5V, 5mA < ILOAD < 250mA ILOAD = 5mA; 4.5V < VCC < to 5.5V V mA 4.30 3.90 UNITS 4.45 V 4.10 V 0.20 V 20 mV 2 mV 0.25 0.40 Ω 2 50 μA 2 50 μA VCC < VCCDES, ILOAD = 0mA VCC > VCCSEL, ILOAD = 0mA VCC > VCCSEL, ILOAD = 250mA 0.20 0.60 0.70 0.40 1.00 1.20 mA mA mA VAUX Supply Current VAUX > VCC VCC > VAUX 0.20 0.02 0.40 0.10 mA mA ROH DRIVE Pull-up Resistance RPULLUP to VCC, VCC > VCCSEL 4.0 8.0 kΩ ROL DRIVE Pull-down Resistance RPULLDOWN to GND, VCCDES > VCC 0.1 0.4 kΩ RSW VAUX Switch Resistance IRCC VCC Reverse Leakage IRAUX VAUX Reverse Leakage IGND Ground Current IAUX VCCDES > VCC, VAUX = 3.3V VAUX = 3.3V, VCC = 0V VAUX = 0V, VCC = 5V Note 1: Operating Characteristics are over Standard Operating Conditions unless otherwise specified. Note 2: The hysteresis defines the maximum level of acceptable disturbance on VCC during switching. It is recommended that the VCC source impedance be kept below 0.25Ω to ensure the switching disturbance remains below the hysteresis during select/deselect transitions. An input capacitor may be required to help minimize the switching transient. Rev. 3 | Page 5 of 12 | www.onsemi.com CMPWR101 Performance Information CMPWR101 Typical DC Characteristics (nominal conditions unless specified otherwise) Rev. 3 | Page 6 of 12 | www.onsemi.com CMPWR101 Rev. 3 | Page 7 of 12 | www.onsemi.com CMPWR101 Performance Information (cont’d) CMPWR101 Transient Characteristics (nominal conditions unless specified otherwise) (VCC source resistance set to 0.2Ω) Rev. 3 | Page 8 of 12 | www.onsemi.com CMPWR101 Performance Information (cont’d) CMPWR101 Typical Thermal Characteristics The overall junction to ambient thermal resistance (θJA) for device power dissipation (PD) consists primarily of two paths in series. The first path is the junction to the case (θJC) which is defined by the package style, and the second path is case to ambient (θCA) thermal resistance which is dependent on board layout. The final operating junction temperature for any set of conditions can be estimated by the following thermal equation: = TAMB + PD (θJC) + PD (θCA) TJUNC = TAMB + PD (θJA) The CMPWR101 uses a standard SOIC package. When this package is mounted on a double-sided printed circuit board with two square inches of copper allocated for "heat spreading", the resulting θJA is 85°C/W. Based on a maximum power dissipation of 0.43W (1.7V x 250mA) with an ambient of 70°C, the resulting junction temperature will be: TJUNC = TAMB + PD (θJA) = 70°C + 0.43W (80°C/W) = 70°C + 37°C = 103°C Thermal characteristics were measured using a double-sided board with two square inches of copper area connected to the GND pin for "heat spreading". Measurements showing performance up to junction temperature of 125°C were performed under light load conditions (5mA). This allows the ambient temperature to be representative of the internal junction temperature. Note: The use of multi-layer board construction with separate ground and power planes will further enhance the overall thermal performance. In the event of no copper area being dedicated for heat spreading, a multi-layer board construction, using only the minimum size pad layout, will provide the CMPWR101 with an overall θJA of 100°C/W which allows up to 500mW to be safely dissipated. Rev. 3 | Page 9 of 12 | www.onsemi.com CMPWR101 Rev. 3 | Page 10 of 12 | www.onsemi.com CMPWR101 Mechanical Details SOIC-8 Mechanical Specifications Dimensions for CMPWR101 devices packaged in 8-pin SOIC packages are presented below. For complete information on the SOIC-8 package, see the California Micro Devices SOIC Package Information document. PACKAGE DIMENSIONS Package SOIC Pins 8 Millimeters Inches Dimensions Min Max Min Max A 1.35 1.75 0.053 0.069 A1 0.10 0.25 0.004 0.010 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 E 3.80 4.19 0.150 0.165 e 1.27 BSC 0.050 BSC H 5.80 6.20 0.228 0.244 L 0.40 1.27 0.016 0.050 # per tube 100 pieces* # per tape and reel 2500 pieces Controlling dimension: inches Package Dimensions for SOIC-8 * This is an approximate number which may vary. Rev. 3 | Page 11 of 12 | www.onsemi.com CMPWR101 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 Rev. 3 | Page 12 of 12 | www.onsemi.com ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative