STMICROELECTRONICS M41T60_10

M41T60
Serial access real-time clock
Features
■
Counters for seconds, minutes, hours, day,
date, month, years, and century
■
32 KHz crystal oscillator integrating load
capacitance and high crystal series resistance
operation
■
Oscillator stop detection monitors clock
operation
■
Serial interface supports I2C bus (400 kHz)
■
350 nA timekeeping current at 3 V
■
Low operating current of 35 µA (at 400 kHz)
■
Timekeeping down to 1.0 V
■
1.3 V to 4.4 V I2C bus operating voltage
■
QFN16 (Q)
3 mm x 3 mm
VSOJ20 (47.6mm2)
2
GND Plane Guard Ring (21.5mm )
SMT
CRYSTAL
Software clock calibration to compensate
deviation of crystal due to temperature
■
Software programmable output (OUT)
■
Operating temperature of –40 to 85 °C
■
Automatic leap year compensation
■
Lead-free 16-pin QFN package
■
Li-ion rechargeable operation
April 2010
1
XI
2
XO
3
4
ST QFN16
Footprint comparison of ST’s QFN16 with
SMT crystal vs. competing VSOJ20 package
Doc ID 10396 Rev 13
1/27
www.st.com
1
Contents
M41T60
Contents
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1
3
2-wire bus characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1.1
Bus not busy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1.2
Start data transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1.3
Stop data transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1.4
Data valid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1.5
Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2
READ mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3
WRITE mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Clock operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.1
Calibrating the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2
Century bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.3
Output driver pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.4
Oscillator stop detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.5
Initial power-on defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
8
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2/27
Doc ID 10396 Rev 13
M41T60
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Century bits examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Operating and AC measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DC characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Crystal electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Crystals suitable for use with M41T6x series RTCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Oscillator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
QFN16 – 16-lead, quad, flat package, no lead, 3 x 3 mm body size, mechanical data . . . 23
Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Doc ID 10396 Rev 13
3/27
List of figures
M41T60
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
4/27
Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
16-pin QFN connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Hardware hookup for SuperCap™ backup operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Serial bus data transfer sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Acknowledgement sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Slave address location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
READ mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Alternate READ mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
WRITE mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Crystal accuracy across temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Calibration waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
AC testing I/O waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Crystal isolation example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Bus timing requirements sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
QFN16 – 16-lead, quad, flat package, no lead, 3 x 3 mm body size, outline . . . . . . . . . . . 23
QFN16, quad, flat package, no lead, 3 x 3 mm, recommended footprint . . . . . . . . . . . . . . 24
32 KHz crystal + QFN16 vs. VSOJ20 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Doc ID 10396 Rev 13
M41T60
Description
The M41T60 is a low power serial RTC with a built-in 32.768 kHz oscillator (external crystal
controlled). Eight registers are used for the clock/calendar function and are configured in
binary coded decimal (BCD) format. Addresses and data are transferred serially via a twoline bi-directional bus. The built-in address register is increased automatically after each
WRITE or READ data byte.
The eight clock address locations contain the century, year, month, date, day, hour, minute,
and second in 24-hour BCD format. Corrections for 28-, 29- (leap year), 30-, and 31-day
months are made automatically.
The M41T60 is supplied in 16-lead QFN package.
Figure 1.
Logic diagram
VCC
XI
FT(1)
XO
M41T60
SCL
OFIRQ/OUT(1)
SDA
VSS
AI08869
1. Open drain
Signal names
XI
Oscillator input
XO
Oscillator output
FT
Frequency test output (open drain)
SDA
Serial data address input/output
SCL
Serial clock
OFIRQ/OUT
VCC
Supply voltage
VSS
Ground
NC
VCC
NC
16-pin QFN connections
16
15
14
13
12
NC
XO
2
11
OFIRQ/OUT
VSS
3
10
SCL
(1)
4
9
SDA
FT
5
6
7
8
NC
1
NC
XI
NC
Figure 2.
Oscillator fail interrupt/out output (open drain)
NC
Table 1.
VSS
1
Description
Doc ID 10396 Rev 13
(1)
AI08870
5/27
Description
M41T60
Figure 3.
Block diagram
(1)
FT
FT
OUT
(1)
OFIRQ/OUT
OFIE
1 Hz
OSCILLATOR
FAIL DETECT
XI
OSCILLATOR
32.768 kHz
SECONDS
DIVIDER
XO
MINUTES
HOURS
CONTROL
LOGIC
VCC
VSS
DAY
DATE
SCL
CENTURY/
MONTH
SERIAL
BUS
INTERFACE
YEAR
ADDRESS
REGISTER
SDA
CALIBRATION
AI08871
1. Open drain output.
Figure 4.
Hardware hookup for SuperCap™ backup operation
VCC
MCU
M41T60
VCC
XI
XO
VSS
VCC
(1)
OFIRQ/OUT
(1)
FT
Port
Port
SCL
Serial Clock Line
SDA
Serial Data Line
AI10476b
1. Open drain output.
6/27
Doc ID 10396 Rev 13
M41T60
2
Operation
Operation
The M41T60 clock operates as a slave device on the serial bus. Access is obtained by
implementing a start condition followed by the correct slave address (D0h). The 8 bytes
contained in the device can then be accessed sequentially in the following order:
2.1
1.
Seconds register
2.
Minutes register
3.
Hours register
4.
Day register
5.
Date register
6.
Century/month register
7.
Years register
8.
Calibration register
2-wire bus characteristics
This bus is intended for communication between different ICs. It consists of two lines: one
bi-directional for data signals (SDA) and one for clock signals (SCL). Both the SDA and the
SCL lines must be connected to a positive supply voltage via a pull-up resistor.
The following protocol has been defined:
●
Data transfer may be initiated only when the bus is not busy.
●
During data transfer, the data line must remain stable whenever the clock line is high.
Changes in the data line while the clock line is high will be interpreted as control
signals.
Accordingly, the following bus conditions have been defined:
2.1.1
Bus not busy
Both data and clock lines remain high.
2.1.2
Start data transfer
A change in the state of the data line, from high to low, while the clock is high, defines the
START condition.
2.1.3
Stop data transfer
A change in the state of the data line, from low to high, while the clock is high, defines the
STOP condition.
2.1.4
Data valid
The state of the data line represents valid data when after a start condition, the data line is
stable for the duration of the high period of the clock signal. The data on the line may be
changed during the low period of the clock signal. There is one clock pulse per bit of data.
Doc ID 10396 Rev 13
7/27
Operation
M41T60
Each data transfer is initiated with a start condition and terminated with a stop condition.
The number of data bytes transferred between the start and stop conditions is not limited.
The information is transmitted byte-wide and each receiver acknowledges with a ninth bit.
By definition, a device that gives out a message is called “transmitter”, the receiving device
that gets the message is called “receiver”. The device that controls the message is called
“master”. The devices that are controlled by the master are called “slaves”.
2.1.5
Acknowledge
Each byte of eight bits is followed by one acknowledge bit. This acknowledge bit is a low
level put on the bus by the receiver, whereas the master generates an extra acknowledge
related clock pulse.
A slave receiver which is addressed is obliged to generate an acknowledge after the
reception of each byte. Also, a master receiver must generate an acknowledge after the
reception of each byte that has been clocked out of the slave transmitter.
The device that acknowledges has to pull down the SDA line during the acknowledge clock
pulse in such a way that the SDA line is a stable low during the high period of the
acknowledge related clock pulse. Of course, setup and hold times must be taken into
account. A master receiver must signal an end-of-data to the slave transmitter by not
generating an acknowledge on the last byte that has been clocked out of the slave. In this
case, the transmitter must leave the data line high to enable the master to generate the
STOP condition.
Figure 5.
Serial bus data transfer sequence
DATA LINE
STABLE
DATA VALID
CLOCK
DATA
START
CONDITION
CHANGE OF
DATA ALLOWED
STOP
CONDITION
AI00587
8/27
Doc ID 10396 Rev 13
M41T60
Operation
Figure 6.
Acknowledgement sequence
CLOCK PULSE FOR
ACKNOWLEDGEMENT
START
SCL FROM
MASTER
1
DATA OUTPUT
BY TRANSMITTER
2
8
MSB
9
LSB
DATA OUTPUT
BY RECEIVER
AI00601
READ mode
In this mode, the master reads the M41T60 slave after setting the slave address
(see Figure 7). Following the WRITE mode control bit (R/W = 0) and the acknowledge bit,
the word address An is written to the on-chip address pointer. Next the START condition
and slave address are repeated, followed by the READ mode control bit (R/W = 1). At this
point, the master transmitter becomes the master receiver. The data byte which was
addressed will be transmitted and the master receiver will send an acknowledge bit to the
slave transmitter. The address pointer is only increased on reception of an acknowledge bit.
The M41T60 slave transmitter will now place the data byte at address An+1 on the bus. The
master receiver reads and acknowledges the new byte and the address pointer is increased
to An+2.
This cycle of reading consecutive addresses will continue until the master receiver sends a
STOP condition to the slave transmitter.
The system-to-user transfer of clock data will be halted whenever the address being read is
a clock address (0h to 6h). The update will resume due to a stop condition or when the
pointer increments to any non-clock address (7h).
An alternate READ mode may also be implemented, whereby the master reads the M41T60
slave without first writing to the (volatile) address pointer. The first address that is read is the
last one stored in the pointer (see Figure 9 on page 10).
Slave address location
R/W
START
A
SLAVE ADDRESS
1
LSB
Figure 7.
MSB
2.2
1
0
1
0
0
0
AI00602
Doc ID 10396 Rev 13
9/27
Operation
M41T60
R/W
DATA n+1
ACK
DATA n
ACK
BUS ACTIVITY:
S
ACK
WORD
ADDRESS (An)
ACK
S
R/W
SDA LINE
ACK
BUS ACTIVITY:
MASTER
START
READ mode sequence
START
Figure 8.
SLAVE
ADDRESS
STOP
SLAVE
ADDRESS
P
NO ACK
DATA n+X
SLAVE
ADDRESS
10/27
Doc ID 10396 Rev 13
DATA n+X
ACK
BUS ACTIVITY:
DATA n+1
ACK
DATA n
P
NO ACK
R/W
S
ACK
SDA LINE
ACK
BUS ACTIVITY:
MASTER
STOP
Alternate READ mode sequence
START
Figure 9.
AI00899
AI00895
M41T60
WRITE mode
In this mode the master transmitter transmits to the M41T60 slave receiver. Bus protocol is
shown in Figure 10 on page 11. Following the START condition and slave address, a logic
'0' (R/W = 0) is placed on the bus and indicates to the addressed device that word address
An will follow and is to be written to the on-chip address pointer. The data word to be written
to the memory is strobed in next and the internal address pointer is increased to the next
address location on the reception of an acknowledge clock. The M41T60 slave receiver will
send an acknowledge clock to the master transmitter after it has received the slave address
and again after it has received the word address and each data byte.
SLAVE
ADDRESS
DATA n+X
P
ACK
DATA n+1
ACK
BUS ACTIVITY:
DATA n
ACK
WORD
ADDRESS (An)
ACK
S
R/W
SDA LINE
ACK
BUS ACTIVITY:
MASTER
STOP
Figure 10. WRITE mode sequence
START
2.3
Operation
AI00591
Doc ID 10396 Rev 13
11/27
Clock operation
3
M41T60
Clock operation
The M41T60 is driven by a quartz-controlled oscillator with a nominal frequency of
32.768 kHz. The accuracy of the real-time clock depends on the frequency of the quartz
crystal that is used as the time-base for the RTC. The eight-byte clock register (see Table 2
on page 14) is used to both set the clock and to read the date and time from the clock, in a
binary coded decimal format. Seconds, minutes, and hours are contained within the first
three registers.
Bits D6 and D7 of clock register 05h (century/month register) contain the century bit 0 (CB0)
and the century bit 1 (CB1). See Table 3 on page 16 for additional explanation. Bits D0
through D2 of register 03h contain the day (day of the week). Registers 04h, 05h, and 06h
contain the date (day of the month), century/month, and years. The eighth clock register is
the calibration register (this is described in the clock calibration section). Bit D7 of register
00h contains the stop bit (ST). Setting this bit to a '1' will cause the oscillator to stop. When
reset to a '0,' the oscillator restarts within one second (typical).
Note:
Upon initial power-up, the user should set the ST bit to a '1,' then immediately reset the ST
bit to '0.' This provides an additional “kick-start” to the oscillator circuit.
Bit D7 of register 01h contains the oscillator fail interrupt enable bit (OFIE - see the
description in the oscillator fail detection section).
Note:
A WRITE to ANY location within the first seven bytes of the clock register (0h-6h), including
the OFIE and ST bit, will result in an update of the system clock and a reset of the divider
chain. This could result in an inadvertent change of the current time. These non-clock
related bits should be written prior to setting the clock, and remain unchanged until such
time as a new clock time is also written.
The seven clock registers may be read one byte at a time, or in a sequential block. The
calibration register (address location 7h) may be accessed independently. A provision has
been made to ensure that a clock update does not occur while any of the clock addresses
are being read. If a clock address is being read, an update of the clock registers will be
halted. this will prevent a transition of data during the READ.
3.1
Calibrating the clock
The M41T60 is driven by a quartz-controlled oscillator with a nominal frequency of
32,768 Hz. The accuracy of the clock is dependent upon the accuracy of the crystal, and the
match between the capacitive load of the oscillator circuit and the capacitive load for which
the crystal was trimmed. The M41T60 oscillator is designed for use with a 6 - 7 pF crystal
load capacitance. When the calibration circuit is properly employed, accuracy improves to
better than ±2 ppm at 25 °C.
The oscillation rate of crystals changes with temperature (see Figure 11 on page 14). The
M41T60 design employs periodic counter correction. The calibration circuit adds or
subtracts counts from the oscillator divider circuit at the divide by 256 stage, as shown in
Figure 12 on page 15. The number of times pulses are blanked (subtracted, negative
calibration) or split (added, positive calibration) depends upon the value loaded into the five
calibration bits found in the calibration register. Adding counts speeds the clock up,
subtracting counts slows the clock down. The calibration bits occupy the five lower-order
bits (D4-D0) in the calibration register 07h.
12/27
Doc ID 10396 Rev 13
M41T60
Clock operation
These bits can be set to represent any value between 0 and 31 in binary format. Bit D5 is a
sign bit; '1' indicates positive calibration, '0' indicates negative calibration.
Calibration occurs within a 64-minute cycle. The first 62 minutes in the cycle may, once per
minute, have one second either shortened by 128 or lengthened by 256 oscillator cycles. If
a binary '1' is loaded into the register, only the first 2 minutes in the 64-minute cycle will be
modified; if a binary 6 is loaded, the first 12 will be affected, and so on. Therefore, each
calibration step has the effect of adding 512 or subtracting 256 oscillator cycles for every
125,829,120 actual oscillator cycles. That is, +4.068 or –2.034 ppm of adjustment per
calibration step in the calibration register. Assuming that the oscillator is running at exactly
32,768 Hz, each of the 31 increments in the calibration byte would represent +10.7 or –5.35
seconds per day which corresponds to a total range of +5.5 or –2.75 minutes per month.
Two methods are available for ascertaining how much calibration a given M41T60 may
require:
Note:
●
The first involves setting the clock, letting it run for a month and comparing it to a
known accurate reference and recording deviation over a fixed period of time.
Calibration values, including the number of seconds lost or gained in a given period,
can be found in application note AN934, “TIMEKEEPER® calibration.” This allows the
designer to give the end user the ability to calibrate the clock as the environment
requires, even if the final product is packaged in a non-user serviceable enclosure. The
designer could provide a simple utility that accesses the calibration byte.
●
The second approach is better suited to a manufacturing environment, and involves the
use of the frequency test (FT) pin. The FT pin will toggle at 512 Hz when the ST bit is
set to '0,' and the OUT bit and FT bit are set to '1.' Any measured deviation from the
512 Hz frequency indicates the degree and direction of oscillator frequency shift at the
test temperature. For example, a reading of 512.010124 Hz would indicate a +20 ppm
oscillator frequency error, requiring a –10 (XX001010) to be loaded into the calibration
byte for correction.
Setting or changing the calibration byte does not affect the frequency test output frequency.
the FT pin is an open drain pin which requires a pull-up resistor to VCC for proper operation.
A 500-10 k resistor is recommended in order to control the rise time.
Doc ID 10396 Rev 13
13/27
Clock operation
M41T60
Table 2.
Register map
Data
Function/range
BCD format
Address
D7
D6
D5
D4
D3
D2
D1
D0
0
ST
10 seconds
Seconds
Seconds
00-59
1
OFIE
10 minutes
Minutes
Minutes
00-59
2
0
0
Hours
Hours
00-23
3
0
0
Day
01-07
4
0
0
Date
01-31
5
CB1
CB0
6
10 hours
0
0
0
Day
10 date
0
Date
10 M.
Month
10 Years
7
OUT
FT
Century/month 0-3/01-12
Years
S
Year
Calibration
●
0 = Must be set to '0.'
●
CB0, CB1 = century bits
●
FT = frequency test bits
●
OFIE = oscillator fail interrupt enable bit
●
OUT = output level
●
S = sign bit
●
ST = stop bit
00-99
Calibration
Figure 11. Crystal accuracy across temperature
Frequency (ppm)
20
0
–20
–40
–60
ΔF = K x (T – T )2
O
F
–80
2
2
K = –0.036 ppm/°C ± 0.006 ppm/°C
–100
TO = 25°C ± 5°C
–120
–140
–160
–40
–30
–20
–10
0
10
20
30
Temperature °C
14/27
Doc ID 10396 Rev 13
40
50
60
70
80
AI07888
M41T60
Clock operation
Figure 12. Calibration waveform
NORMAL
POSITIVE
CALIBRATION
NEGATIVE
CALIBRATION
AI00594b
3.2
Century bits
These two bits will increment in a binary fashion at the turn of the century, and handle leap
years correctly. See Table 3 on page 16 for additional explanation.
3.3
Output driver pin
When the OFIE bit is not set to generate an interrupt, the OFIRQ/OUT pin becomes an
output driver that reflects the contents of D7 of the calibration register. In other words, when
D7 (OUT bit) is a '0,' then the OFIRQ/OUT pin will be driven low.
Note:
The OFIRQ/OUT pin is an open drain which requires an external pull-up resistor.
3.4
Oscillator stop detection
In the event that the oscillator has either stopped, or was stopped for some period of time,
and if the oscillator fail interrupt enable (OFIE) bit is set to a '1,' an interrupt will be
generated. This interrupt can be used to judge the validity of the clock and date data.
The interrupt will be active any time the oscillator stops while VCC is ≥ 1.0V. The following
conditions will cause the OFIRQ pin to be active:
●
the ST bit is set to '1.'
●
external interference or removal of the crystal.
The oscillator fail interrupt (OFIRQ) will remain active until the OFIE bit is reset to '0,' or the
oscillator restarts.
The oscillator must start and have run for at least 4 seconds before attempting to set the
OFIE bit to '1.'
Doc ID 10396 Rev 13
15/27
Clock operation
3.5
M41T60
Initial power-on defaults
Upon initial application of power to the device, the OUT bit will be set to a '1,' while the ST,
OFIE, and FT bits will be set to '0.' All other register bits will initially power-on in a random
state.
Table 3.
Century bits examples
CB0
CB1
Leap year?
Example(1)
0
0
Yes
2000
0
1
No
2100
1
0
No
2200
1
1
No
2300
1. Leap year occurs every four years (for years evenly divisible by four), except for years evenly divisible by
100. The only exceptions are those years evenly divisible by 400 (the year 2000 was a leap year, year
2100 is not).
16/27
Doc ID 10396 Rev 13
M41T60
4
Maximum ratings
Maximum ratings
Stressing the device above the rating listed in the absolute maximum ratings table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the operating sections of
this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
Table 4.
Absolute maximum ratings
Symbol
Parameter
Conditions(1)
Value(2)
Unit
TSTG
Storage temperature (VCC off, oscillator off)
–55 to 125
°C
VCC
Supply voltage
–0.3 to 5.0
V
260
°C
–0.2 to
Vcc+0.3
V
TSLD(3)
Lead solder temperature for 10 seconds
VIO
Input or output voltages
IO
Output current
20
mA
PD
Power dissipation
1
W
VESD(HBM)
Electro-static discharge voltage
(Human Body Model)
TA = 25°C
>1500
V
VESD(RCDM)
Electro-static discharge voltage
(Robotic Charged Device Model)
TA = 25°C
>1000
V
1. Test conforms to JEDEC standard
2. Data based on characterization results, not tested in production
3. Reflow at peak temperature of 260 °C. The time above 255 °C must not exceed 30 seconds.
Doc ID 10396 Rev 13
17/27
DC and AC parameters
5
M41T60
DC and AC parameters
This section summarizes the operating and measurement conditions, as well as the DC and
AC characteristics of the device. The parameters in the following DC and AC characteristic
tables are derived from tests performed under the measurement conditions listed in the
relevant tables. Designers should check that the operating conditions in their projects match
the measurement conditions when using the quoted parameters.
Table 5.
Operating and AC measurement conditions
Parameter
Note:
M41T60
Supply voltage (VCC)
1.3 V to 4.4 V
Ambient operating temperature (TA)
–40 to 85 °C
Load capacitance (CL)
50 pF
Input rise and fall times
≤ 5 ns
Input pulse voltages
0.2 VCC to 0.8 VCC
Input and output timing ref. voltages
0.3 VCC to 0.7 VCC
Output Hi-Z is defined as the point where data is no longer driven.
Figure 13. AC testing I/O waveform
0.8VCC
0.7VCC
0.3VCC
0.2VCC
AI02568
Figure 14. Crystal isolation example
Local Grounding Plane
(Layer 2)
XI
Crystal
XO
GND
AI09127
Note:
18/27
Substrate pad should be tied to VSS.
Doc ID 10396 Rev 13
M41T60
DC and AC parameters
Table 6.
Capacitance
Parameter (1)(2)
Symbol
CIN
COUT(3)
tLP
Min
Max
Unit
Input capacitance (SCL)
-
7
pF
Output capacitance (SDA, OUT)
-
10
pF
Low-pass filter input time constant (SDA and SCL)
-
50
ns
1. Effective capacitance measured with power supply at 3.6 V; sampled only, not 100% tested.
2. At 25 °C, f = 1 MHz.
3. Outputs deselected.
Table 7.
Symbol
VCC(2)
DC characteristics
Test condition(1)
Parameter
Clock
Operating voltage
I
2C
Min
(3)
Typ
1.0
bus (400 kHz)
1.3
VCC = 4.4 V
ICC1
ICC2
Supply current
Supply current
(Standby)
SCL = 400 kHz
(No load)
SCL = 0 Hz
All inputs
≥ VCC – 0.2 V
≤ VSS + 0.2 V
Max
Unit
4.4
V
4.4
V
100
µA
70
µA
VCC = 3.6 V
50
VCC = 3.0 V
35
µA
VCC = 2.5 V
30
µA
VCC = 2.0 V
20
µA
4.4 V
950
nA
700
nA
3.6 V
375
3.0 V at 25 °C
350
nA
2.0 V at 25 °C
310
nA
VIL
Input low voltage
–0.2
0.3 VCC
V
VIH
Input high voltage
0.7 VCC
VCC + 0.3
V
VOL
Output low voltage
VCC = 4.4 V, IOL = 3 mA (SDA)
0.4
V
VCC = 4.4 V, IOL = 1 mA (OFIRQ/OUT)
0.4
V
Pull-up supply
voltage (open drain)
FT, OFIRQ/OUT
4.4
V
ILI
Input leakage current
0 V ≤ VIN ≤ VCC
–1.0
+1.0
µA
ILO
Output leakage
current
0 V ≤ VOUT ≤ VCC
–1.0
+1.0
µA
1. Valid for ambient operating temperature: TA = –40 to 85 °C; VCC = 1.3 to 4.4 V (except where noted).
2. When using battery backup, VCC fall time should not exceed 10 mV/µs.
3. Oscillator startup guaranteed at 1.5 V only.
Doc ID 10396 Rev 13
19/27
DC and AC parameters
Table 8.
M41T60
Crystal electrical characteristics
Parameter (1)(2)
Symbol
Min
Typ
32.768
fO
Resonant frequency
-
RS
Series resistance
(TA = –40 to 70°C, oscillator startup at 2.0 V)
-
CL
Load capacitance
-
Max
Unit
kHz
75 (3)(4)
6
kΩ
pF
1. For the QFN16 package, user-supplied, external crystals are required. The 6 and 7 pF crystals listed in Table 9 below have
been evaluated by ST and have been found to be satisfactory for use with the M41T6x series RTCs.
2. Load capacitors are integrated within the M41T60. Circuit board layout considerations for the 32.768 kHz crystal of
minimum trace lengths and isolation from RF generating signals should be taken into account.
3. Guaranteed by design.
4. RS (max) = 65 kΩ for TA = –40 to 85 °C and oscillator startup at 1.5 V.
Table 9.
Crystals suitable for use with M41T6x series RTCs
Manufacturer’s specifications
Vendor
ESR
max
Temp.
range
(°C)
50 kΩ
–40/+85
±20 ppm
6 pF
3.2 x 1.5 x 0.9 mm SMT 70 kΩ
–40/+85
±20 ppm
7 pF
Order number
Package
8.3 x 2.5 mm
leaded SMT
Rated
Rated
tolerance load
at 25 °C
cap.
Citizen
CMJ206T-32.768KDZB-UB
Citizen
CM315-32.768KDZY-UB
Ecliptek
E4WCDA06-32.768K
2.0 x 6.0 mm thru-hole
50 kΩ
–10/+60
±20 ppm
6 pF
Ecliptek
E5WSDC 07 - 32.768K
7 x 1.5 x 1.4 mm SMT
65 kΩ
–40/+85
±20 ppm
7 pF
ECS
ECS-.327-6-17X-TR
3.8 x 8.5 x 2.5 mm SMT 50 kΩ
–10/+60
±20 ppm
6 pF
ECS
ECS-.327-7-34B-TR
3.2 x 1.5 x 0.9 mm SMT 70 kΩ
–40/+85
±20 ppm
7 pF
ECS
ECS-.327-7-38-TR
(1)
7 x 1.5 x 1.4 mm SMT
65 kΩ
–40/+85
±20 ppm
7 pF
7 x 1.5 x 1.4 mm SMT
65 kΩ
–40/+85
±20 ppm
7 pF
Epson
MC-146 32.7680KA-AG: ROHS
Fox
298LF-0.032768-19
1.5 x 5.0 mm thru-hole
50 kΩ
–20/+60
±20 ppm
6 pF
Fox
299LF-0.032768-37
2.0 x 6.0 mm thru-hole
50 kΩ
–20/+60
±20 ppm
6 pF
Fox
414LF-0.032768-12
3.8 x 8.5 x 2.5 mm SMT 50 kΩ
–40/+85
±20 ppm
6 pF
Fox
501LF-0.032768-5
Micro
Crystal
MS3V-T1R 32.768KHZ 7PF 20PPM
Pletronics SM20S - 32.768K - 6pF
7 x 1.5 x 1.4 mm SMT
65 kΩ
–40/+85
±20 ppm
7 pF
6.7 x 1.4 mm
leaded SMT
65 kΩ
–40/+85
±20 ppm
7 pF
3.8 x 8.5 x 2.5 mm SMT 50 kΩ
–40/+85
±20 ppm
6 pF
Seiko
SSPT7F-7PF20PPM
7 x 1.5 x 1.4 mm SMT
65 kΩ
–40/+85
±20 ppm
7 pF
Seiko
VT200F-6PF20PPM
2.0 x 6.0 mm thru-hole
50 kΩ
–10/+60
±20 ppm
6 pF
1. Epson MC-146 32.7680KA-E: ROHS is 6 pF version.
20/27
Doc ID 10396 Rev 13
M41T60
DC and AC parameters
Table 10.
Oscillator characteristics
Symbol
Parameter
VSTA
Oscillator start voltage
tSTA
Oscillator start time
Cg
XIN capacitance
Cd
XOUT capacitance
Conditions
Min
≤ 10 seconds
1.5
Typ
Max
V
VCC = 3.0 V
IC-to-IC frequency variation
(1)
Unit
1
s
12
pF
12
pF
–10
+10
ppm
1. Reference value. TA = 25 °C, VCC = 3.0 V, CMJ-145 (CL = 6 pF, 32,768 Hz) manufactured by Citizen,
CL = Cg • Cd / (Cg + Cd)
Figure 15. Bus timing requirements sequence
SDA
tBUF
tHD:STA
tHD:STA
tR
tF
SCL
tHIGH
P
S
tLOW
tSU:DAT
tHD:DAT
SR
tSU:STA
P
tSU:STO
AI00589
Note:
P = STOP and S = START
Table 11.
AC characteristics
Parameter(1)
Symbol
Min
Max
Unit
0
400
kHz
fSCL
SCL clock frequency
tLOW
Clock low period
1.3
tHIGH
Clock high period
600
µs
ns
tR
SDA and SCL rise time
300
ns
tF
SDA and SCL fall time
300
ns
tHD:STA
START condition hold time
(after this period the first clock pulse is generated)
600
ns
tSU:STA
START condition setup time
(only relevant for a repeated start condition)
600
ns
tSU:DAT
Data setup time
100
ns
tHD:DAT(2)
Data hold time
tSU:STO
tBUF
0
µs
STOP condition setup time
600
ns
Time the bus must be free before a new transmission can
start
1.3
µs
1. Valid for ambient operating temperature: TA = –40 to 85 °C; VCC = 1.3 to 4.4 V (except where noted).
2. Transmitter must internally provide a hold time to bridge the undefined region (300 ns max.) of the falling
edge of SCL.
Doc ID 10396 Rev 13
21/27
Package mechanical data
6
M41T60
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
22/27
Doc ID 10396 Rev 13
M41T60
Package mechanical data
Figure 16. QFN16 – 16-lead, quad, flat package, no lead, 3 x 3 mm body size, outline
D
E
A3
A
A1
ddd C
e
b
L
K
1
2
Ch
E2
3
K
D2
Note:
QFN16-A
Drawing is not to scale.
Table 12.
QFN16 – 16-lead, quad, flat package, no lead, 3 x 3 mm body size,
mechanical data
mm
inches
Dim
Typ
Min
Max
Typ
Min
Max
A
0.90
0.80
1.00
0.035
0.032
0.039
A1
0.02
0.00
0.05
0.001
0.000
0.002
A3
0.20
–
–
0.008
–
–
b
0.25
0.18
0.30
0.010
0.007
0.012
D
3.00
2.90
3.10
0.118
0.114
0.122
D2
1.70
1.55
1.80
0.067
0.061
0.071
E
3.00
2.90
3.10
0.118
0.114
0.122
E2
1.70
1.55
1.80
0.067
0.061
0.071
e
0.50
–
–
0.020
–
–
K
0.20
–
–
0.008
–
–
L
0.40
0.30
0.50
0.016
0.012
0.020
ddd
–
0.08
–
–
0.003
–
Ch
–
0.33
–
–
0.013
–
N
16
Doc ID 10396 Rev 13
16
23/27
Package mechanical data
M41T60
Figure 17. QFN16, quad, flat package, no lead, 3 x 3 mm, recommended footprint
1.60
3.55
2.0
0.28
Note:
AI09126
Substrate pad should be tied to VSS.
Figure 18. 32 KHz crystal + QFN16 vs. VSOJ20 mechanical data
7.0 ± 0.3
VSOJ20
6.0 ± 0.2
3.2
SMT
CRYSTAL
1
XI
2
XO
2.9
3
4
1.5
ST QFN16
2.9
AI11146
Note:
24/27
Dimensions shown are in millimeters (mm).
Doc ID 10396 Rev 13
M41T60
7
Part numbering
Part numbering
Table 13.
Ordering information scheme
Example:
M41T
60
Q
6
F
Device family
M41T
Device type and supply voltage
60 = VCC = 1.3 to 4.4 V
Package
Q = QFN16 (3 mm x 3 mm)
Temperature range
6 = –40 to 85 °C
Shipping method
F = ECOPACK® package, tape & reel
For other options, or for more information on any aspect of this device, please contact the
ST sales office nearest you.
Doc ID 10396 Rev 13
25/27
Revision history
8
M41T60
Revision history
Table 14.
26/27
Revision history
Date
Revision
Changes
13-Nov-2003
1
20-Nov-2003
1.1
25-Dec-2003
2
13-Jan-2004
2.1
Update characteristics (Figure 9, 10, 12; Table 7, 13)
26-Feb-2004
2.2
Update characteristics and mechanical dimensions (Figure 14, 17;
Table 4 , 7, 12)
02-Mar-2004
2.3
Update characteristics (Table 7)
26-Apr-2004
3
Reformat and republish
13-May-2004
4
Update characteristics (Table 7, 8; Figure 14 , 17)
06-Aug-2004
5
Update characteristics (Figure 2; Table 7, 10)
25-Oct-2004
6
Document status promotion; update characteristics (Figure 1;
Table 4 ,7, 8, 10, 12)
20-Dec-2004
7
Corrected footprint; update characteristics (Figure 4, 17; Table 7)
05-May-2005
8
Add package comparison and mechanical data (Figure 18)
31-Oct-2005
9
Update: bus operating voltage, characteristics (Figure 4;
Table 4, 7, 11, 13)
30-Nov-2005
10
Update ESD:HBM rating, crystal characteristics (Table 4, 8)
06-Jul-2006
11
New template
26-Jan-2010
12
Minor textual changes; updated footnote 3 of Table 4; updated footnote
1 of Table 8; added Table 9; updated Table 10, 11, Section 3.1; added
text to Section 6: Package mechanical data.
29-Apr-2010
13
Updated Table 9; minor textual change in Section 4.
First issue
Update characteristics (Figure 2, 3, 4; Table 1, 2, 5, 7, 11)
Reformatted; add crystal isolation, footprint (Figure 12)
Doc ID 10396 Rev 13
M41T60
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 10396 Rev 13
27/27