FREESCALE MW4IC915GMBR1

MW4IC915
Freescale Semiconductor
Rev.
6, 5/2006
Replaced
by
MW4IC915NBR1(GNBR1).
There
are
no
form,
fit
or
function
changes
with
this
part
Technical Data
replacement. N suffix added to part number to indicate transition to lead - free terminations.
ARCHIVE INFORMATION
The MW4IC915MB/GMB wideband integrated circuit is designed for GSM
and GSM EDGE base station applications. It uses Freescale’s newest High
Voltage (26 to 28 Volts) LDMOS IC technology and integrates a multi - stage
structure. Its wideband On- Chip design makes it usable from 750 to 1000 MHz.
The linearity performances cover all modulations for cellular applications: GSM,
GSM EDGE, TDMA, N - CDMA and W - CDMA.
Final Application
• Typical Performance: VDD = 26 Volts, IDQ1 = 60 mA, IDQ2 = 240 mA,
Pout = 15 Watts CW, Full Frequency Band (860 - 960 MHz)
Power Gain — 30 dB
Power Added Efficiency — 44%
Driver Application
• Typical GSM/GSM EDGE Performances: VDD = 26 Volts, IDQ1 = 60 mA,
IDQ2 = 240 mA, Pout = 3 Watts Avg., Full Frequency Band (869 - 894 MHz
and 921 - 960 MHz)
Power Gain — 31 dB
Power Added Efficiency — 19%
Spectral Regrowth @ 400 kHz Offset = - 65 dBc
Spectral Regrowth @ 600 kHz Offset = - 83 dBc
EVM — 1.5%
• Capable of Handling 5:1 VSWR, @ 26 Vdc, 921 MHz, 15 Watts CW
Output Power
• Characterized with Series Equivalent Large - Signal Impedance Parameters
• On - Chip Matching (50 Ohm Input, DC Blocked, >3 Ohm Output)
• Integrated Quiescent Current Temperature Compensation with
Enable/Disable Function
• On - Chip Current Mirror gm Reference FET for Self Biasing Application(1)
• Integrated ESD Protection
• 200°C Capable Plastic Package
• In Tape and Reel. R1 Suffix = 500 Units per 44 mm, 13 inch Reel.
VRD2
VRG2
VDS1
RFin
VDS2/RFout
VRD1
VRG1
VGS1
Quiescent Current
Temperature Compensation
VGS2
Figure 1. Functional Block Diagram
MW4IC915MBR1
MW4IC915GMBR1
860 - 960 MHz, 15 W, 26 V
GSM/GSM EDGE, N - CDMA
RF LDMOS WIDEBAND
INTEGRATED POWER AMPLIFIERS
CASE 1329 - 09
TO - 272 WB - 16
PLASTIC
MW4IC915MBR1
CASE 1329A - 03
TO - 272 WB - 16 GULL
PLASTIC
MW4IC915GMBR1
GND
VRD2
VRG2
VDS1
VRD1
1
2
3
4
5
16
15
GND
NC
RFin
6
14
VRG1
VGS1
VGS2
NC
GND
RFout/
VDS2
7
8
9
10
11
13
12
NC
GND
ARCHIVE INFORMATION
RF LDMOS Wideband Integrated
Power Amplifiers
(Top View)
Note: Exposed backside flag is source
terminal for transistors.
Figure 2. Pin Connections
1. Refer to AN1987/D, Quiescent Current Control for the RF Integrated Circuit Device Family. Go to http://www.freescale.com/rf.
Select Documentation/Application Notes - AN1987.
© Freescale Semiconductor, Inc., 2006. All rights reserved.
RF Device Data
Freescale Semiconductor
MW4IC915MBR1 MW4IC915GMBR1
1
Table 1. Maximum Ratings
Symbol
Value
Unit
Drain- Source Voltage
Rating
VDSS
- 0.5. +65
Vdc
Gate- Source Voltage
VGS
- 0.5. +15
Vdc
Storage Temperature Range
Tstg
- 65 to +175
°C
Operating Junction Temperature
TJ
200
°C
Symbol
Value (1)
Table 2. Thermal Characteristics
ARCHIVE INFORMATION
Thermal Resistance, Junction to Case
Unit
RθJC
°C/W
GSM Application
(Pout = 15 W CW)
Stage 1, 26 Vdc, IDQ = 60 mA
Stage 2, 26 Vdc, IDQ = 240 mA
7.3
1.7
GSM EDGE Application
(Pout = 7.5 W CW)
Stage 1, 26 Vdc, IDQ = 60 mA
Stage 2, 26 Vdc, IDQ = 240 mA
7.3
1.8
CDMA Application
(Pout = 3.75 W CW)
Stage 1, 26 Vdc, IDQ = 60 mA
Stage 2, 26 Vdc, IDQ = 240 mA
7.4
1.9
Table 3. ESD Protection Characteristics
Test Conditions
Class
Human Body Model
1 (Minimum)
Machine Model
M3 (Minimum)
Charge Device Model
C2 (Minimum)
Table 4. Moisture Sensitivity Level
Test Methodology
Per JESD 22 - A113, IPC/JEDEC J - STD - 020
Rating
Package Peak Temperature
Unit
3
260
°C
Table 5. Electrical Characteristics (TC = 25°C unless otherwise noted)
Characteristic
Symbol
Min
Typ
Max
Unit
Functional Tests (In Freescale Test Fixture, 50 ohm system) VDS = 26 Vdc, IDQ1 = 90 mA, IDQ2 = 240 mA, Pout = 15 W PEP,
f1 = 869 MHz, f2 = 869.1 MHz and f1 = 960 MHz and f2 = 960.1 MHz, Two - Tone
Power Gain
Gps
29
31
—
dB
Power Added Efficiency
PAE
29
31
—
%
Intermodulation Distortion
IMD
—
- 40
- 29
dBc
Input Return Loss
IRL
—
- 15
- 10
dB
1. Refer to AN1955/D, Thermal Measurement Methodology of RF Power Amplifiers. Go to http://www.freescale.com/rf.
Select Documentation/Application Notes - AN1955.
ARCHIVE INFORMATION
Characteristic
(continued)
MW4IC915MBR1 MW4IC915GMBR1
2
RF Device Data
Freescale Semiconductor
Table 5. Electrical Characteristics (TC = 25°C unless otherwise noted) (continued )
Characteristic
Symbol
Min
Typ
Max
Unit
Typical Performances (In Freescale Reference Board) VDS = 26 V, IDQ1 = 60 mA, IDQ2 = 240 mA, 869 MHz<Frequency>960 MHz
ΔIQT
—
±5
—
%
Gain Flatness in 40 MHz Bandwidth @ Pout = 3 W CW
GF
—
0.2
—
dB
Deviation from Linear Phase in 40 MHz Bandwidth @ Pout = 3 W CW
Φ
—
±0.6
—
°
Delay
—
2.5
—
ns
ΔΦ
—
±15
—
°
Quiescent Current Accuracy over Temperature
with 1.8 kΩ Gate Feed Resistors ( - 10 to 85°C) (1)
Delay @ Pout = 3 W CW Including Output Matching
Part - to - Part Phase Variation @ Pout = 3 W CW
ARCHIVE INFORMATION
Output Power, 1dB Compression Point
P1dB
—
20
—
Watts
Power Gain @ Pout = 15 W CW
Gps
—
30
—
dB
Power Added Efficiency @ Pout = 15 W CW
PAE
—
44
—
%
Input Return Loss @ Pout = 15 W CW
IRL
—
- 15
—
dB
Error Vector Magnitude @ Pout = 3 W Avg. including
0.6% rms source EVM
EVM
—
1.5
—
% rms
Spectral Regrowth at 400 kHz Offset @ Pout = 3 W Avg.
SR1
—
- 65
—
dBc
Spectral Regrowth at 600 kHz Offset @ Pout = 3 W Avg.
SR2
—
- 83
—
dBc
1. Refer to AN1977/D, Quiescent Current Thermal Tracking Circuit in the RF Integrated Circuit Family. Go to http://www.freescale.com/rf.
Select Documentation/Application Notes - AN1977.
ARCHIVE INFORMATION
Typical GSM/GSM EDGE Performances (In Freescale Reference Board) VDS = 26 V, IDQ1 = 60 mA, IDQ2 = 240 mA,
869 MHz<Frequency<960 MHz
MW4IC915MBR1 MW4IC915GMBR1
RF Device Data
Freescale Semiconductor
3
L1
VDS1
+
C1
RF
INPUT
VGS1
C2
C3
Z1
16
R1
+
C5
C4
C8
C7
R2
C10 C11
NC 15
14
6
C6
VGS2
1
2
3
4
5
VDS2
Z2
Z3
C12
Z4
M1
C13
7
8
9
Z5
+
+
C15
C14
Z6
M2
10 NC
11
Z8
M4
C16
Z9
RF
OUTPUT
Z7
M3
NC 13
Quiescent Current
Temperature Compensation
12
Z1
Z2
Z3
Z4
Z5
Z6
Z7
Z8
Z9
PCB
0.086″, 50 W Microstrip
0.133″ x 0.236″ Microstrip
0.435″ x 0.283″ Microstrip
0.171″ x 0.283″ Microstrip
0.429″ x 0.283″ Microstrip
0.157″ x 0.283″ Microstrip
0.429″ x 0.283″ Microstrip
0.394″ x 0.088″ Microstrip
0.181″ x 0.088″ Microstrip
Taconic TLX8, 0.030″, εr = 2.55
Figure 3. MW4IC915MBR1(GMBR1) Test Fixture Schematic
Table 6. MW4IC915MBR1(GMBR1) Test Fixture Component Designations and Values
Part
Description
Part Number
Manufacturer
C1, C6, C9, C14
22 mF, 35 V Tantalum Chip Capacitors
TAJE226M035R
AVX
C2, C5, C8, C11
1000 pF Chip Capacitors
100B102JCA500X
ATC
C3, C4, C7, C10, C16
22 pF Chip Capacitors
100B220JCA500X
ATC
C12, C13
10 pF Chip Capacitors
100B100JCA500X
ATC
C15
10 mF Tantalum Chip Capacitor
T491X226K035AS4394
Kemet
L1
12.5 nH Inductor
M1, M2, M3, M4
0.283″, 90_ Mitered Microstrip Bends
R1, R2
10 kΩ, 1/4 W Chip Resistor (1206)
ARCHIVE INFORMATION
ARCHIVE INFORMATION
+
C9
MW4IC915MBR1 MW4IC915GMBR1
4
RF Device Data
Freescale Semiconductor
C1
VDS1
C2
C11
MW4IC915MB
Rev 0
VDS2
C14
C15
C3
C10
L1
C16
C12
C13
C5
C4
C7
ARCHIVE INFORMATION
VGS1
C9
VGS2
R2
Freescale has begun the transition of marking Printed Circuit Boards (PCBs) with the Freescale Semiconductor
signature/logo. PCBs may have either Motorola or Freescale markings during the transition period. These changes will have
no impact on form, fit or function of the current product.
Figure 4. MW4IC915MBR1(GMBR1) Test Fixture Component Layout
ARCHIVE INFORMATION
C8
C6
R1
MW4IC915MBR1 MW4IC915GMBR1
RF Device Data
Freescale Semiconductor
5
VDS
+
+
C7
RF
INPUT
C10
C9
Z1
16
14
6
ARCHIVE INFORMATION
Z2
Z3
C15
Z4
Z5
C2
Z6
C3
Z7
NC 13
Quiescent Current
Temperature Compensation
12
VGS
R2
R7
+
P2
C8
C16
R4
R3
R6
C13
C14
P1
C17
R5
Z1
Z2
Z3
Z4
RF
OUTPUT
C1
10 NC
11
C12
C6
NC 15
7
8
9
C11
C5
0.681″ x 0.039″, 50 W Microstrip
0.157″ x 0.228″ Microstrip
0.468″ x 0.157″ Microstrip
0.220″ x 0.157″ Microstrip
Z5
Z6
Z7
PCB
0.566″ x 0.043″ Microstrip
0.165″ x 0.043″ Microstrip
0.078″ x 0.043″ Microstrip
Taconic RF35, 0.02″, εr = 3.5
Figure 5. MW4IC915MBR1(GMBR1) Reference Board Schematic
Table 7. MW4IC915MBR1(GMBR1) Reference Board Component Designations and Values
Part
Description
Part Number
Manufacturer
C1, C15
10 pF Chip Capacitors (0805), ACCU - P
08051J100GBT
AVX
C2
5.6 pF Chip Capacitor (0805), ACCU - P
08051J5R6BBT
AVX
C3, C4, C9, C11, C13
33 pF Chip Capacitors (0805), ACCU - P
08051J330GB
AVX
C5, C10, C12, C14
10 nF Chip Capacitors (0805)
08055C103KAT
AVX
C6, C7, C8
22 mF, 35 V Tantalum Capacitors
TAJE226MO35R
AVX
C16, C17
100 nF Chip Capacitors (0805)
08055C104KAT
AVX
P1, P2
5 kΩ Potentiometer CMS Cermet Multi - turn
3224W
Bourns
R1, R2, R3, R4, R5
0 Ω, 1/8 W Chip Resistors (0805)
R6, R7
10 kΩ, 1/4 W Chip Resistors (1206)
ARCHIVE INFORMATION
R1
1
2
3
4
5
C4
MW4IC915MBR1 MW4IC915GMBR1
6
RF Device Data
Freescale Semiconductor
GROUND
VDD
R1
C6
C7
C5
ARCHIVE INFORMATION
C15
C13
C3
C1
C11
C14
C2
C12
R7
R6
C17
P1
R5
MW4IC915MB
Rev 0
P2
C16
C8
R4
R3
R2
VGG
GROUND
Freescale has begun the transition of marking Printed Circuit Boards (PCBs) with the Freescale Semiconductor
signature/logo. PCBs may have either Motorola or Freescale markings during the transition period. These changes will have
no impact on form, fit or function of the current product.
Figure 6. MW4IC915MBR1(GMBR1) Reference Board Component Layout
ARCHIVE INFORMATION
C4
C10
C9
MW4IC915MBR1 MW4IC915GMBR1
RF Device Data
Freescale Semiconductor
7
32
PAE
30
−8
−16
IRL
28
−24
26
IMD3
24
22
−32
−40
−48
VDD = 26 Vdc
Pout = 15 W (PEP)
IDQ1 = 90 mA, IDQ2 = 240 mA
Two−Tone Measurement
100 kHz Tone Spacing
20
18
16
880
900
920
940
−56
−64
−72
−80
960
f, FREQUENCY (MHz)
0
Gps
32
−7
30
−14
28
−21
IRL
26
VDD = 26 Vdc
Pout = 6 W (PEP)
IDQ1 = 90 mA, IDQ2 = 240 mA
Two−Tone Measurement
100 kHz Tone Spacing
24
22
IMD3
20
PAE
18
−35
−42
−49
−56
16
14
860
−28
−63
880
900
920
−70
960
940
−20
IMD, INTERMODULATION DISTORTION (dBc)
34
IRL, INPUT RETURN LOSS (dB)
IMD3, INTERMODULATION DISTORTION (dB)
PAE, POWER ADDED EFFICIENCY (%), Gps, POWER GAIN (dB)
Figure 7. Two - Tone Wideband Circuit Performance @ Pout = 15 Watts PEP
3rd Order
−30
5th Order
−40
7th Order
−50
−60
−70
VDD = 26 Vdc
IDQ1 = 90 mA, IDQ2 = 240 mA
f = 960 MHz
100 kHz Tone Spacing
−80
−90
0.1
1
f, FREQUENCY (MHz)
10
100
Pout, OUTPUT POWER (WATTS) Avg.
Figure 8. Two - Tone Wideband Circuit Performance
@ Pout = 6 Watts
Figure 9. Intermodulation Distortion Products
versus Output Power
TYPICAL CHARACTERISTICS (FREESCALE REFERENCE BOARD)
−30_C
33 V = 26 Vdc
DD
IDQ1 = 60 mA, IDQ2 = 240 mA
32 f = 910 MHz
85_C
PAE
30
32
16
28
27
0.1
40
24
85_C
29
56
48
Gps
25_C
31
25_C
8
1
10
0
100
Pout, OUTPUT POWER (WATTS)
Figure 10. Power Gain and Power Added Efficiency
versus Output Power
35
34
G ps , POWER GAIN (dB)
TC = −30_C
PAE, POWER ADDED EFFICIENCY (%)
34
TC = −30_C
33
VDD = 26 Vdc
Pout = 3 W CW
IDQ1 = 60 mA, IDQ2 = 240 mA
32
25_C
31
ARCHIVE INFORMATION
0
Gps
14
860
G ps , POWER GAIN (dB)
ARCHIVE INFORMATION
PAE, POWER ADDED EFFICIENCY (%),
Gps, POWER GAIN (dB)
34
IRL, INPUT RETURN LOSS (dB)
IMD3, INTERMODULATION DISTORTION (dBc)
TYPICAL CHARACTERISTICS (FREESCALE TEST FIXTURE, 50 OHM SYSTEM)
30
85_C
29
28
860
870
880
890
900
910
920
930
940
950
960
f, FREQUENCY (MHz)
Figure 11. Power Gain versus Frequency
MW4IC915MBR1 MW4IC915GMBR1
8
RF Device Data
Freescale Semiconductor
TYPICAL CHARACTERISTICS (FREESCALE REFERENCE BOARD) - CONTINUED
21
G ps , POWER GAIN (dB)
VDD = 26 Vdc
Pout = P1dB
IDQ1 = 60 mA, IDQ2 = 240 mA
32
31
PAE, POWER ADDED EFFICIENCY (%)
TC = −30_C
33
25_C
30
85_C
4
3.5
3
870
880
890
900
910
920
930
940
950
85_C
18
VDD = 26 Vdc
Pout = 3 W CW
IDQ1 = 60 mA, IDQ2 = 240 mA
870
880
890
900
910
920
930
940
950
f, FREQUENCY (MHz)
Figure 12. Power Gain versus Frequency
Figure 13. Power Added Efficiency versus
Frequency
−50
VDD = 26 Vdc
IDQ1 = 60 mA, IDQ2 = 240 mA
EDGE Modulation
f = 910 MHz
25_C
−30_C
TC = 85_C
2
1.5
1
0.5
1
10
100
TC = 85_C
−30_C
−60
−65
−70
VDD = 26 Vdc
IDQ1 = 60 mA, IDQ2 = 240 mA
EDGE Modulation
f = 910 MHz
−75
1
0.1
10
Pout, OUTPUT POWER (WATTS)
Figure 14. Error Vector Magnitude versus
Output Power
Figure 15. Spectral Regrowth at 400 kHz
versus Output Power
SPECTRAL REGROWTH @ 600 kHz (dBc)
Pout, OUTPUT POWER (WATTS) AVG.
−70
−72
−74
VDD = 26 Vdc
IDQ1 = 60 mA, IDQ2 = 240 mA
EDGE Modulation
f = 910 MHz
−76
TC = −30_C
−78
960
25_C
−55
−80
0.1
25_C
f, FREQUENCY (MHz)
2.5
0
TC = −30_C
19
17
860
960
SPECTRAL REGROWTH @ 400 kHz (dBc)
28
860
EVM, ERROR VECTOR MAGNITUDE (% rms)
ARCHIVE INFORMATION
29
20
100
ARCHIVE INFORMATION
34
85_C
25_C
−80
−82
−84
−86
0.1
1
10
100
Pout, OUTPUT POWER (WATTS)
Figure 16. Spectral Regrowth at 600 kHz
versus Output Power
MW4IC915MBR1 MW4IC915GMBR1
RF Device Data
Freescale Semiconductor
9
Zo = 5 Ω
Zload
f = 900 MHz
VDD = 26 V, IDQ1 = 60 mA, IDQ2 = 240 mA, Pout = P1dB
f
MHz
Zload
Ω
900
3.23 - j4.30
910
3.24 - j4.36
920
3.25 - j4.42
930
3.25 - j4.47
940
3.23 - j4.52
950
3.21 - j4.56
960
3.16 - j4.60
970
3.11 - j4.65
980
3.04 - j4.70
Zload
= Test circuit impedance as
measured from drain to ground.
Output
Matching
Network
Device
Under Test
Z
in
ARCHIVE INFORMATION
ARCHIVE INFORMATION
f = 980 MHz
Z
load
Figure 17. Series Equivalent Input and Load Impedance
MW4IC915MBR1 MW4IC915GMBR1
10
RF Device Data
Freescale Semiconductor
ARCHIVE INFORMATION
ARCHIVE INFORMATION
NOTES
MW4IC915MBR1 MW4IC915GMBR1
RF Device Data
Freescale Semiconductor
11
ARCHIVE INFORMATION
ARCHIVE INFORMATION
NOTES
MW4IC915MBR1 MW4IC915GMBR1
12
RF Device Data
Freescale Semiconductor
ARCHIVE INFORMATION
ARCHIVE INFORMATION
NOTES
MW4IC915MBR1 MW4IC915GMBR1
RF Device Data
Freescale Semiconductor
13
PACKAGE DIMENSIONS
MW4IC915MBR1 MW4IC915GMBR1
14
RF Device Data
Freescale Semiconductor
MW4IC915MBR1 MW4IC915GMBR1
RF Device Data
Freescale Semiconductor
15
MW4IC915MBR1 MW4IC915GMBR1
16
RF Device Data
Freescale Semiconductor
MW4IC915MBR1 MW4IC915GMBR1
RF Device Data
Freescale Semiconductor
17
MW4IC915MBR1 MW4IC915GMBR1
18
RF Device Data
Freescale Semiconductor
MW4IC915MBR1 MW4IC915GMBR1
RF Device Data
Freescale Semiconductor
19
How to Reach Us:
Home Page:
www.freescale.com
E - mail:
[email protected]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1 - 800- 521- 6274 or +1 - 480- 768- 2130
[email protected]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1 - 8 - 1, Shimo - Meguro, Meguro - ku,
Tokyo 153 - 0064
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1 - 800- 441- 2447 or 303 - 675- 2140
Fax: 303 - 675- 2150
[email protected]
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do
vary in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescalet and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc. 2006. All rights reserved.
RoHS- compliant and/or Pb - free versions of Freescale products have the functionality and electrical
characteristics of their non - RoHS- compliant and/or non - Pb- free counterparts. For further
information, see http://www.freescale.com or contact your Freescale sales representative.
For information on Freescale’s Environmental Products program, go to http://www.freescale.com/epp.
MW4IC915MBR1 MW4IC915GMBR1
MW4IC915
Rev. 6, 5/2006
20
RF Device Data
Freescale Semiconductor