BATTERY DRIVEN, FTP-608 Series 2” HIGH SPEED THERMAL PRINTER FTP-628MCL353/354 #01 / #02 ■ OVERVIEW The FTP-628 MCL Series are battery driven high-speed printers with a 2-inch paper width equivalent. The FTP-628 MCL Series can be used for a variety of applications, such as portable terminals, POS, ticket issuing machines, label printers, banking terminals, and measurement and medical equipment. ■ HIGHLIGHTS • Ultra compact Height 26.4 mm, width 83.5 mm, depth 43.0 mm FTP-628MCL354 • High speed printing It can print at 60 mm/s (480 dotlines/s) maximum by using Fujitsu's unique head drive control. • Auto Cutter Full cut type (#01) and partial cut type (#02) printers are available. • Easy paper setting Our unique platen release mechanism allows a wide paper route even if the printer is ultra-compact, so paper can be easily inserted. Conventional auto loading is also available. FTP-628DSL306 1 FTP-628MCL353/354 ■ PART NUMBERS Part Number Printer mechanism with Cutter FTP-628MCL353#01 (front paper insertion, full cut type with knob) FTP-628MCL353#02 (front paper insertion, partial cut type with knob) FTP-628MCL354#01 (bottom paper insertion, full cut type without knob) FTP-628MCL354#02 (bottom paper insertion, partial cut type without knob) LSI for driving FTP-628CU301 (ANK only) Interface Board Cutter for Mech/Cutter supported FTP-628DCL301 Parallel (Centronics) FTP-628DSL306 Serial (RS232C) Interface cables Parallel (Centronics) FTP-628Y202 Serial (RS232C) FTP-628Y302 Power cable Head, motor, logic FTP-628Y402 ■ SPECIFICATIONS Item Specifications Part number FTP-628MCL353#01/#02, FTP-628MCL354#01/#02 Printing method Thermal-line dot method Dot structure 384 dots/line Dot pitch (Horizontal) 0.125 mm (8 dots/mm)—Dot density Dot pitch (Vertical) 0.125 mm (8 dots/mm)—Line feed pitch Effective printing area 48 mm Number of columns ANK 32 columns/line (maximum 12 x 24 dot font) Paper width 58 mm Paper thickness 60 to 80 µ m (some paper in this range may not be used because of paper characteristics) Printing Speed Maximum 60mm/sec. (480 dot line/sec.) at 8.5V Character types Alphanumeric, kana: International characters: JIS Kanji (Kanji CG loaded board): Character, dimensions (W×H), number of columns 159 types 195 types about 6800 types 12 × 24 dots, (1.5 × 3.0 mm), 32 columns: ANK 24 × 24 dots, (3.0 × 3.0 mm), 16 columns: ANK 8 × 16 dots, (1.0 × 2.0 mm), 48 columns: ANK 16 × 16 dots, (2.0 × 2.0 mm), 24 columns: ANK 2 FTP-628MCL353/354 ■ SPECIFICATIONS Item Interface Power supply Specification Conforms to RS232C / Centronics For print head 4.2 - 8.5 VDC average current, 0.78A (0.93A) peak value (print ratio: 12.5%, print speed: 50mm/sec. at 7.2V) For motor 4.2 - 8.5 VDC, 1A maximum For cutter 5 VDC ± 5%, 1A maximum For logic 5 VDC ± 5%, 0.1 A maximum Mechanism with cutter 83.5 x 43.0 x 26.4 mm (WxDxH) Interface board 69.3 x 52 x 15mm Mechanism with cutter Approximately 120g Interface board Approximately 20g Head Pulse resistance: 100 million pulses/dot (under our standard conditions); Abrasion resistance: paper traveling distance 50km (print ratio: 25% or less) Cutter 300,000 cuts Operating temperature* 0˚ C to 50˚ C Dimensions Weight Life Operating humidity Operating environment Storage temperature Detection function 20 to 85% RH (no condensation) -20˚ C to +60˚ C (paper not included) Storage humidity 5 to 95% RH (no condensation) Head temperature detection Detected by thermistor Paper out/mark detection Detected by photo-interrupter Platen release Detected by sliding switch Recommended thermal sensitive paper High Sensitive Paper TF50KS-E4 (Nippon Paper) Standard paper: TF60KS-E(Nippon Paper), FTP020PU001 (58mm), PD105R (Oji Paper), FTP-020P0701 (58mm) Medium Life Paper TF60KS-F1, FTP-020P0102 (58mm), PD170R (Oji Paper), P220VBB-1 Mitsubishi Paper) Long Life Paper PD160R-N (Oji Paper), AFB-235 (Mitsubishi Paper), TP50KJ-R (Nippon Paper), HA220AA (Nippon Paper) *+5˚C to +40˚C printing density assurance rance (-25 to 70˚C capability) 3 FTP-628MCL353/354 ■ FUNCTION OF INTERFACE BOARD Item Item 1. Test print function 8. Cutter trouble detect 2. Paper out detection 9. Motor power saving function 3. Paper near end detection 10. Mark detection function 4. Platen open detection 11. MCU operation abnormality detection 5. Thermal head temperature abnormality detection 12. Power ON/OFF sequence protection 6. Blow-out fuse detection 13. Motor over-current protection 7. Head voltage abnormality detection 14. Hardware timer ■ DIMENSIONS 1. Printer mechanism FTP-628MCL353 FTP-628MCL354 83.5 1 26.4 12 at release at close 38.6 80.5 1 at close 58 (26. 32 29.5 (67) (67) (26 3 (75) (75) 3 MAX at release 38.6 26.4 58 3 MAX 45˚ 33.7 45˚ .9 33.7 (37.2) (37.2) Unit: mm Note: 1. Dimensions are nominal value (tolerance ±5 unless otherwise specified). 2. Platen unit (lever, platen, etc) moves by approximately 0.7mm toward paper insertion direction when platen is open. 4 FTP-628MCL353/354 2. Interface board Unit: mm 5 FTP-628MCL353/354 1. Connector (FPC) specification (CN4) (1) Connector Mechanical unit side: FPC connector Remote side (housing site): 52610-3090 (made by Molex) (2) Pin assignment on the mechanical side No Signal I/O Contents — Cathode for photo interruptor 1 PHK 2 VSEN 3 PHE O Emittor for photo interruptor 4 SW1 O Platen release switch 5 SW2 I Platen release switch 6 VH I 7 VH I 8 DI I Data in 9 CLK I Synchronous clock for communication 10 GND — 11 GND — 12 STB6 I 13 STB5 I 14 STB4 I 15 VDD I 16 TM O Thermally sensitive resistor input termnial 1 17 TM O Thermally sensitive resistor input termnial 2 18 STB3 I 19 STB2 I 20 STB1 I 21 GND — 22 GND — 23 LAT I 24 DO O 25 VH I 26 VH I 27 MT/A I 28 MT/A I 29 MT/B I 30 MT/B I I paper sensor power Head drive power Ground power supply for thermal head Thermal head energizing control signal Logic power Thermal head energizing control signal Ground power supply for thermal head Data latch Data out Power supply for thermal head Stepping motor excitation signal 6 FTP-628MCL353/354 Sensor (Photointerruptor) Platen unit Thermal head Motor FPC Connect terminal: surface side Connector No 30,29, .....................2,1 (FPC pin numbers) 2. Cutter (CN5) Connector on control circuit side: B4B-PH-K-S (J.S.T. or equivalent) No. Signal I/O 1 CHP I 3 MT+ O Contents No. Signal I/O Cutter position detect signal 2 GND - Logic ground Stepping motor coil excitation A 4 MT- O Not connected Fujitsu Components International Headquarter Offices Contents Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: www.fceu.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: www.fcai.fujitsu.com Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #04-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] www.fcal.fujitsu.com © 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered trademarks of their respective owners. Rev. 11/15/2004. 7