Sept. 1995 Edition 2.0a DATA SHEET MB511 1GHz HIGH SPEED PRESCALER HIGH SPEED PRESCALER The Fujitsu MB511 is a 1.0GHz high speed prescaler that forms a Phase Locked Loop (PLL) circuit when combined with a Fujitsu frequency synthesizer.Based on Fujitsu’s advanced Bipolar processing, the MB511 maintains a consistent low power consumption of 23mA @ 5V. In addition, it can detect low amplitude input signals with a sensitivity of –20dBm min. The MB511 will divide the input frequency a modulus of 1, 2, or 8, and is well suited for applications in CATV and electronically tuned TV. PLASTIC PACKAGE DIP-08P-M01 FEATURES Wide operating frequency range: fin = 50 to 1000MHz (vin = –20dBm) Maximum operating frequency depends upon a divide ratio: 1/1: 250MHz max. (Buffer through) 1/2: 500MHz max. 1/8: 1000MHz max. Low supply current: 23mA @5V High input sensitivity: –20dBm min. Stable Output Amplitude: 800mVp–p (CL < 5pF) Wide temperature range: TA = –40 to +85°C PLASTIC PACKAGE FPT-08P-M01 PIN ASSIGNMENT Plastic 8-pin Dual-In-Line package (Suffix: –P) Plastic 8-pin Flat package (Suffix: –PF) IN 1 8 IN VCC 2 7 S1 ABSOLUTE MAXIMUM RATINGS (See Note) Rating Symbol Value Unit Power Supply Voltage VCC –0.5 to +7.0 V Input Voltage VIN –0.5 to VCC +0.5 V Output Current IO 10 mA TSTG –55 to +125 °C Storage Temperature Note: Permanent device damage may occur if the above Absolute Maximum Ratings are exceeded. Functional operation should be restricted to the conditions as detailed in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Copyright 1995 by FUJITSU LIMITED and FUJITSU MICROELECTRONICS, INC. TOP VIEW NC 3 6 S2 OUT 4 5 GND This device contains circuitry to protect the inputs against damage due to high static voltages or electric fields. However, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum rated voltages to this high impedance circuit. MB511 D Q D Q D Q C Q C Q C Q IN OUT IN S1 Divide Ratio Controller S2 Figure 1. MB511 Block Diagram FUNCTION TABLE S1 S2 Divide Ratio Operating Frequency L L Not used — L H 1 250MHz H L 2 500MHz H H 8 1000MHz H = VCC L = OPEN PIN DESCRIPTIONS 2 Pin Number Symbol I/O Descriptions 1 IN I Input. The connection with VCO should be an AC connection. 2 VCC – Power supply voltage input. 3 NC – No connection. 4 OUT O Output. Termination resistor is necessary due to emitter follower output. 5 GND – Ground. 6 S2 I Divide ratio control input. 7 S1 I Divide ratio control input. 8 IN I Complementary Input. MB511 RECOMMENDED OPERATING CONDITIONS Value Parameter Symbol Unit Min. Typ. Max. 5.0 5.5 V +85 °C 5 pF Power Supply Voltage VCC 4.5 Operating Temperature TA –40 Load Capacitance CL Note Termination resistor 500Ω ELECTRICAL CHARACTERISTICS Value Parameter Symbol Unit Min. Typ. Max. Note Power Supply Current ICC 15 23 32 mA Except termination output current. Output Amplitude VO 0.4 0.8 1.2 Vp–p 500Ω termination, CL = 5pF max. 1/1 f1 50 250 MHz 1/2 f2 50 500 MHz 1/8 f3 50 1000 MHz PIN –20 +10 dBm VIH VCC –0.7 VCC +0.5 V Input Frequency Input Signal Amplitude High Level Input Voltage S1 S2 S1, Low Level Input Voltage Low Level Input Current VIL S1, S2 IIH VCC OPEN 40 Min. value is measured Min g capacitor of with coupling 1000pF 1000pF. 50Ω V 160 µA VCC = 5V 3 MB511 VCC = +5.0V + 10% 0.1µF VCC SW1 Sampling scope prober point for output waveform SW2 1000pF IN P.G. 50Ω MB511 500Ω IN GND 1000pF Figure 2. Test Circuit 4 5pF (including scope and jig capacitance) MB511 TYPICAL CHARACTERISTICS CURVES +10 +10 TA = 25°C 0 Guaranteed Operating Area 50 to 1000MHz –20 to +5dBm –10 MINIMUM INPUT SIGNAL AMPLITUDE PIN (dBm) MINIMUM INPUT SIGNAL AMPLITUDE PIN (dBm) TA = 25°C 0 Guaranteed Operating Area 50 to 500MHz –20 to +5dBm –10 –20 –20 VCC = 5.0V –30 –30 VCC = 4.5V VCC = 5.5V 10 VCC = 4.5V 100 1000 INPUT FREQUENCY fin (MHz) Figure 3. Input Sensitivity Curve (1/8 Divide Ratio) Power Supply Voltage Dependency VCC = 5.0V VCC = 5.5V 10 AMPLITUDE P 100 1000 INPUT FREQUENCY fin (MHz) Figure 4. Input Sensitivity Curve (1/2 Divide Ratio) Power Supply Voltage Dependency TA = 25°C 0 Guaranteed Operating Area 50 to 250MHz –20 to +5dBm –10 –20 VCC = 4.5V –30 VCC = 5.0V VCC = 5.5V 10 100 1000 INPUT FREQUENCY fin (MHz) Figure 5. Input Sensitivity Curve (1/1 Divide Ratio) Power Supply Voltage Dependency POWER SUPPLY CURRENT Icc (mA) MINIMUM INPUT SIGNAL AMPLITUDE PIN (dBm) +10 28.0 TA = 25°C 26.0 24.0 Typ (23.0mA) 22.0 5.5 5.0 4.5 POWER SUPPLY VOLTAGE VCC (V) Figure 6. Power Supply Current vs. Power Supply Voltage 5 MB511 TYPICAL CHARACTERISTICS CURVES (Continued) +10 +10 VCC = 5.0V 0 Guaranteed Operating Area 50 to 1000MHz –20 to +5dBm –10 –20 TA = –40°C –30 TA = 25°C TA = +85°C 10 MINIMUM INPUT SIGNAL AMPLITUDE PIN (dBm) MINIMUM INPUT SIGNAL AMPLITUDE PIN (dBm) VCC = 5.0V 0 –10 –20 TA = –40°C –30 TA =+ 25°C TA = +85°C 10 100 1000 INPUT FREQUENCY fin (MHz) Figure 7. Input Sensitivity Curve (1/8 Divide Ratio) Temperature Dependency Guaranteed Operating Area 50 to 1000MHz –20 to +5dBm 100 1000 INPUT FREQUENCY fin (MHz) Figure 6. Input Sensitivity Curve (1/2 Divide Ratio) Temperature Dependency POWER SUPPLY CURRENT Icc (mA) +10 MINIMUM INPUT SIGNAL AMPLITUDE PIN (dBm) VCC = 5.0V 0 Guaranteed Operating Area 50 to 1000MHz –20 to +5dBm –10 –20 TA = –40°C TA = +25°C –30 TA = +85°C 10 100 1000 INPUT FREQUENCY fin (MHz) Figure 9. Input Sensitivity Curve (1/1 Divide Ratio) Temperature Dependency 6 28.0 VCC = 5.0V 26.0 24.0 Typ (23.0mA) 22.0 –40 40 0 TEMPERATURE TA (°C) Figure 10. Power Supply Current vs. Temperature 80 MB511 PACKAGE DIMENSIONS 8-LEAD PLASTIC DUAL IN-LINE PACKAGE (CASE No: DIP-08P-M01) ) .016 .370 – .012 0.40 ǒ9.40 )– 0.30 Ǔ 15° MAX INDEX .244+.010 (6.20+0.25) ǒ ) .012 .039 – 0 Ǔ ) 0.30 0.99 – 0 ǒ ) .012 .060 – 0 .300(7.62) TYP .010+.002 Ǔ (0.25+0.05) ) 0.30 1.52 – 0 ) .014 .035 – .012 0.35 ǒ0.89 )– 0.30 Ǔ .172(4.36) MAX .020(0.51) MIN .100(2.54) .018+.003 TYP (0.46+0.08) 1988 FUJITSU LIMITED D08006S-2C .118(3.00) MIN DImensions in inches (millimeters) 7 MB511 PACKAGE DIMENSIONS (Continued) 8-LEAD PLASTIC FLAT PACKAGE (CASE No: FPT-08P-M01) ) .010 .250 – .008 ) 0.25 6.35 – 0.20 ǒ .089(2.25) MAX (SEATED HEIGHT) .002(0.05) MIN Ǔ (STAND OFF) .307+.016 (7.80+0.40) INDEX ) .016 .268 – .008 .209+.012 (5.30+0.30) ǒ Ǔ ) 0.40 6.80 – 0.20 .020+.008 (0.50+0.20) .050(1.27) .018+.004 (0.45+0.10) TYP ∅ .005(0.13) ) .002 .006 – .001 M ǒ Ǔ ) 0.05 0.15 – 0.02 .150(3.81) Details of “A” part REF “A” .004(0.10) 1988 FUJITSU LIMITED F08002S-3C All Rights Reserved. Circuit diagrams utilizing Fujitsu products are included as a means of illustrating typical semiconductor applications. Complete information sufficient for construction purposes is not necessarily given. The information contained in this document has been carefully checked and is believed to be reliable. However, Fujitsu assumes no responsibility for inaccuracies. The information contained in this document does not convey any license under the copyrights, patent rights or trademarks claimed and owned by Fujitsu. Fujitsu reserves the right to change products or specifications without notice. No part of this publication may be copied or reproduced in any form or by any means, or transferred to any third party without prior written consent of Fujitsu. 8 .008(0.20) .020(0.50) .007(0.18) MAX .027(0.68) MAX DImensions in inches (millimeters) MB511 FUJITSU LIMITED For further information please contact: Japan FUJITSU LIMITED International Marketing Div. Furukawa Sogo Bldg., 6-1, Marunouchi 2-chome Chiyoda-ku, Tokyo 100, Japan Tel: (03) 3216-3211 Telex: 781-2224361 FAX: (03) 3215-0662 North and South America FUJITSU MICROELECTRONICS, INC. Semiconductor Division 3545 North First Street San Jose, CA 95134-1804, USA Tel: 408-922-9000 FAX: 408-432-9044 Europe FUJITSU MIKROELEKTRONIK GmbH Am Siebenstein 6-10, 6072 Dreieich-Buchschlag, Germany Tel: (06103) 690-0 Telex: 411963 FAX: (06103) 690-122 Asia FUJITSU MICROELECTRONICS ASIA PTE LIMITED 51 Bras Basah Road, Plaza By The Park, #06-04 to #06-07 Singapore 0719 Tel: 336-1600 Telex: 55573 FAX: 336-1609 FUJITSU LIMITED 1990 Printed in Japan PV0039–901A2 9