HY64UD16162M Series Document Title 1M x 16 bit Low Low Power 1T/1C Pseudo SRAM Revision history Revision No. History Draft Date Remark 1.0 Initial Jan. 04. ’ 01 Preliminary 1.1 Revised Jul. 03. ’ 01 Preliminary Jul.18. ’ 01 Preliminary Oct. 07. ‘ 01 Preliminary Nov. 14. ’ 01 Preliminary Dec. 20. ‘ 01 Preliminary Feb. 27. ‘ 02 Preliminary Mar. 11. ‘ 02 Final - Change Pin Connection - Improve tOE from 45ns to 30ns - Correct State Diagram 1.2 Revised - Correct Package Dimension - Change Absolute Maximum Ratings 1.3 Revised - DC Electrical Characteristics ( IDPD,ICC1) - State Diagram - Power Up Sequence - Deep Power Down Sequence - Read/Write Cycle Note 1.4 Revised - DC Electrical Characteristics ( ICC1: 3mA - > 5mA) 1.5 Revised - Improve Standby Current ISB1 from 100uA to 80uA - Add 70ns Part - Power Up Sequence 1.6 Revised - Improve ISB1@70ns 100uA to 85uA - Improve ISB1@85ns 80uA to 75uA - Improve ICC2@70ns 30mA to 25mA - Improve ICC2@85ns 30mA to 20mA - Improve Ambient Temperature C/E to E/I (0°C~85°C/-25°C~85°C → -25°C~85°C/-40°C~85°C) - Improve Maximum Absolute Ratings (Vdd : -0.3V to 3.3V → -0.3V to 3.6V) - Improve tOE@85ns 30ns to 20ns 1.7 Revised - Pin Description - Power Up & Deep Power Down Exit Sequence This document is a general product description and is subject to change without notice. Hynix Semiconductor Inc. does not assume any responsibility for use of circuits described. No patent licenses are implied. Revision 1.7 March. 2002 1 HY64UD16162M Series 1M x 16 bit Low Low Power 1T/1C SRAM DESCRIPTION FEATURES The HY64UD16162M is a 16Mbit 1T/1C SRAM featured by high-speed operation and super low power consumption. The HY64UD16162M adopts one transistor memory cell and is organized as 1,048,576 words by 16bits. The HY64UD16162M operates in the extended range of temperature and supports a wide operating voltage range. The HY64UD16162M also supports the deep power down mode for a super low standby current. The HY64UD16162M delivers the high-density low power SRAM capability to the high-speed low power system. • CMOS Process Technology • 1M x 16 bit Organization • TTL compatible and Tri-state outputs • Deep Power Down : Memory cell data hold invalid • Standard pin configuration : 48-FBGA • Data mask function by /LB, /UB PRODUCT FAMILY Product No. Voltage [V] HY64UD16162M-DF70E HY64UD16162M-DF70I HY64UD16162M-DF85E HY64UD16162M-DF85I 2.7~3.3 2.7~3.3 2.7~3.3 2.7~3.3 Power Dissipation Mode 1CS 1CS 1CS 1CS with with with with /UB,/LB:tCS1 /UB,/LB:tCS1 /UB,/LB:tCS1 /UB,/LB:tCS1 (ISB1,Max) (IDPD,Max) (ICC2,Max) 85µA 2µA 25mA 85µA 2µA 25mA 75µA 2µA 20mA 75µA 2µA 20mA Speed tRC[ns] Temp. [°C] 70 70 85 85 -25~85 -40~85 -25~85 -40~85 Note 1. tCS - /UB,/LB=High : Chip Deselect. PIN CONNECTION (Top View) /OE A0 A1 A2 ROW DECODER CS2 A0 IO10 IO11 A5 A6 IO2 IO3 Vss IO12 A17 A7 IO4 Vdd Vdd IO13 DNU A16 IO5 Vss A19 IO15 IO14 A14 A15 IO6 IO7 IO16 A19 A12 A13 /WE IO8 A18 A8 A9 A10 A11 NC /CS1 CS2 /WE /OE /LB /UB MEMORY ARRAY 1,024K x 16 IO8 DATA I/O BUFFER IO1 WRITE DRIVER /CS1 BLOCK DECODER A4 PRE DECODER A3 ADD INPUT BUFFER /UB COLUMN DECODER IO9 IO1 SENSE AMP /LB BLOCK DIAGRAM IO9 IO16 CONTROL LOGIC PIN DESCRIPTION Pin Name /CS1 CS2 /WE /LB /UB DNU NC Pin Function Chip Select Deep Power Down Write Enable Lower Byte(IO1~IO8) Upper Byte(IO9~IO16) Do Not Use No Connection Pin Name /OE IO1~IO8 IO9~IO16 A0~A19 Vdd Vss Pin Function Output Enable Lower Data Inputs/Outputs Upper Data Inputs/Outputs Address Inputs Power(2.7V~3.3V) Ground This document is a general product description and is subject to change without notice. Hynix Semiconductor Inc. does not assume any responsibility for use of circuits described. No patent licenses are implied. Revision 1.7 March. 2002 2 HY64UD16162M Series ORDERING INFORMATION Part Number Speed HY64UD16162M-E 70 / 85 HY64UD16162M-I 70 / 85 Note 1. E : Extended Temp. (-25°C ~ 85°C) 2. I : Industrial Temp. (-40°C ~ 85°C) Power LL-Part LL-Part Temperature E1 I2 Package FBGA FBGA ABSOLUTE MAXIMUM RATINGS 1 Symbol VIN,VOUT Vdd Parameter Input/Output Voltage Power Supply TA Rating -0.3 to Vdd+0.3 Ambient Temperature TSTG PD Storage Temperature Power Dissipation Ball Soldering Temperature & Time TSOLDER -0.3 to 3.6 -25 to 85 -40 to 85 -55 to 150 1.0 260•10 Unit V V °C °C °C W °C•sec Remark HY64UD16162M-E HY64UD16162M-I Note 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is stress rating only and the functional operation of the device under these or any other conditions above those indicated in the operation of this specification is not implied. Exposure to the absolute maximum rating conditions for extended period may affect reliability. TRUTH TABLE /CS1 CS2 H X X L L L L L L L L L H L H H H H H H H H H H /WE /OE /LB /UB Mode X X X L H H L H H L H H X X X X L H X L H X L H X X H L L L H H H L L L X X H H H H L L L L L L Deselected Deselected Deselected Write Read Output Disabled Write Read Output Disabled Write Read Output Disabled I/O Pin Power I/O1~I/O8 I/O9~I/O16 High-Z High-Z Standby High-Z High-Z Deep Power Down High-Z High-Z Standby DIN High-Z Active DOUT High-Z Active High-Z High-Z Active High-Z DIN Active High-Z DOUT Active High-Z High-Z Active DIN DIN Active DOUT DOUT Active High-Z High-Z Active Note 1. H=VIH, L=VIL, X=don’ t care(VIL or VIH) 2. /UB, /LB(Upper, Lower Byte enable) These active LOW inputs allow individual bytes to be written or read. When /LB is LOW, data is written or read to the lower byte, I/O1 - I/O8. When /UB is LOW, data is written or read to the upper byte, I/O9 - I/O16. Revision 1.7 March. 2002 3 HY64UD16162M Series RECOMMENDED DC OPERATING CONDITION Symbol Vdd VSS VIH VIL Parameter Supply Voltage Ground Input High Voltage Input Low Voltage Min. 2.7 0 2.2 -0.31 Typ. 3.0 - Max. 3.3 0 Vdd+0.3 0.6 Unit V V V V Note 1. VIL=-1.5V for pulse width less than 10ns Undershoot is sampled, not 100% tested. DC ELECTRICAL CHARACTERISTICS Vdd=2.7V~3.3V, TA= -25°C to 85°C(E) / -40°C to 85°C(I) Sym. Parameter Test Condition ILI Input Leakage Current VSS≤VIN≤Vdd ILO Output Leakage Current VSS≤VOUT≤Vdd, /CS1=VIH, CS2=VIH, /OE=VIH or /WE=VIL ICC Operating Power Supply Current Average Operating Current ICC1 -1 - 1 µA /CS1=VIL, CS2=VIH, VIN=VIH or VIL, II/O=0mA - - 3 mA /CS1≤ 0.2V, CS2 ≥Vdd-0.2V, VIN ≤0.2V or VIN≥Vdd-0.2V, Cycle Time=1µs. 100% Duty, II/O=0mA - - 5 mA - - 25 mA 2.4 - 20 0.5 85 75 2 0.4 - mA mA µA µA µA V V /CS1=VIL, CS2=VIH, VIN=VIH or VIL, Cycle Time=Min. 100% Duty, II/O=0mA ICC2 ISB TTL Standby Current ISB1 Standby Current(CMOS Input) IDPD VOL VOH Deep Power Down Curent Output Low Voltage Output High Voltage Min. Typ. Max. Unit -1 1 µA 70ns 85ns /CS1,CS2=VIH or /UB,/LB= VIH /CS1, CS2≥Vdd-0.2V 70ns or /UB,/LB ≥Vdd-0.2V 85ns CS2≤VSS+0.2V IOL=2.1mA IOH=-1.0mA CAPACITANCE (Temp = 25°C, f=1.0MHz) Symbol Parameter CIN Input Capacitance(Add, /CS1, CS2, /WE, /OE, /UB, /LB) COUT Output Capacitance(I/O) Condition VIN=0V VI/O=0V Max. Unit 8 pF 10 pF Note : These parameters are sampled and not 100% tested Revision 1.7 March. 2002 4 HY64UD16162M Series AC CHARACTERISTICS Vdd=2.7V~3.3V, TA = -25°C to 85°C(E) / -40°C to 85°C(I), unless otherwise specified -70 -85 # Symbol Parameter Min. Max. Min. Max. Read Cycle 1 tRC Read Cycle Time 70 85 2 tAA Address Access Time 70 85 3 tACS Chip Select Access Time 70 85 4 tOE Output Enable to Output Valid 20 20 5 tBA /LB, /UB Access Time 70 85 6 tCLZ Chip Select to Output in Low Z 10 10 7 tOLZ Output Enable to Output in Low Z 5 5 8 tBLZ /LB, /UB Enable to Output in Low Z 10 10 9 tCHZ Chip Disable to Output in High Z 0 20 0 30 10 tOHZ Out Disable to Output in High Z 0 20 0 30 11 tBHZ /LB, /UB Disable to Output in High Z 0 20 0 30 12 tOH Output Hold from Address Change 10 10 Write Cycle 13 tWC Write Cycle Time 70 85 14 tCW Chip Selection to End of Write 60 70 15 tAW Address Valid to End of Write 60 70 16 tBW /LB, /UB Valid to End of Write 60 70 17 tAS Address Set-up Time 0 0 18 tWP Write Pulse Width 50 60 19 tWR Write Recovery Time 0 0 20 tWHZ Write to Output in High Z 0 20 0 30 21 tDW Data to Write Time Overlap 30 30 22 tDH Data Hold from Write Time 0 0 23 tOW Output Active from End of Write 5 5 - Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns AC TEST CONDITIONS TA = -25°C to 85°C(E) / -40°C to 85°C(I), unless otherwise specified Parameter Value Input Pulse Level 0.4V to 2.2V Input Rising and Fall Time 5ns Input and Output Timing Reference Level 1.5V Output Load See Below AC TEST LOADS RL=50 Ohm DOUT VL=1.5 V Z0=50 Ohm CL1 =30 pF Note 1. Including jig and scope capacitance. Revision 1.7 March. 2002 5 HY64UD16162M Series Power-Up Sequence 1. Supply power. 2. Maintain stable power for longer than 200µs. Deep Power Down Entry Sequence 1. Keep CS2 low state. Deep power down mode is maintained while CS2 is low state. Deep Power Down Exit Sequence 1. Keep CS2 high state. 2. Maintain stable power for longer than 200µs. STATE DIAGRAM / CS1=VIL, CS2=VIH, /UB&/LB≠VIH Deep Power Down Exit Sequence Power-Up Sequence Power Power On On CS2=VIH Wait µs 200 Wait 200µ 200µs Active Active CS2=VIL CS2=VIH, /CS1=VIH or /UB,/LB=VIH Standby Standby Mode Mode Deep Deep Power Power Down Down Mode Mode CS2=VIL Deep Power Down Entry Sequence STANDBY MODE CHARACTERISTICS Mode Memory Cell Data Standby Valid Deep Power Down Invalid Revision 1.7 March. 2002 Standby Current[µA] 85 / 70ns 75 / 85ns 2 Wait Time[µs] 0 200 6 HY64UD16162M Series TIMING DIAGRAM READ CYCLE 1 ( Note 1, 4 ) tRC ADD tAA tOH tACS /CS1 tCHZ(3) CS2 Vih tBA /UB, /LB tBHZ(3) tOE /OE tOHZ(3) tOLZ(3) tBLZ(3) tCLZ(3) Data Out High-Z Data Valid READ CYCLE 2 ( Note 1, 2, 4 )( CS2=Vih ) tRC ADD tAA tOH tOH Data Out Previous Data Data Valid READ CYCLE 3 ( Note 1, 2, 4 )( CS2=Vih ) /CS1 /UB, /LB tACS tCHZ(3) tCLZ(3) Data Out High-Z Data Valid Notes : 1. Read Cycle occurs whenever a high on the /WE and /OE is low, while /UB and/or /LB and /CS1 and CS2 are in active status. 2. /OE = VIL 3. tCHZ, tBHZ and tOHZ are defined as the time at which the outputs achieve the high impedance state and tOLZ,tBLZ and tCLZ are defined as the time at which the outputs achieve the low impedance state. These are not referenced to output voltage levels. 4. /CS1 in high for the standby, low for active. /UB and /LB in high for the standby, low for active. Revision 1.7 March. 2002 7 HY64UD16162M Series WRITE CYCLE 1 ( Note 1, 4, 5, 9, 10 ) ( /WE Controlled ) tWC ADD tWR(2) tCW /CS1 CS2 Vih tAW tBW /UB, /LB /WE tWP tAS tDW Data In High-Z tDH Data Valid tWHZ(3,8) tOW (6) (7) Data Out WRITE CYCLE 2 ( Note 1, 4, 5, 9, 10 ) ( /CS1 Controlled ) tWC ADD tAS tWR(2) tCW /CS1 CS2 Vih tAW tBW /UB, /LB tWP /WE tDW Data In Data Out High-Z tDH Data Valid High-Z Notes : 1. A write occurs during the overlap of low /CS1, low /WE and low /UB and/or /LB. 2. tWR is measured from the earlier of /CS1, /LB, /UB, or /WE going high to the end of write cycle. 3. During this period, I/O pins are in the output state so that the input signals of opposite phase to the output must not be applied. 4. If the /CS1, /LB and /UB low transition occur simultaneously with the /WE low transition or after the /WE transition, outputs remain in a high impedance state. 5. /OE is continuously low (/OE=VIL) 6. Q(data out) is the invalid data. 7. Q(data out) is the read data of the next address. 8. tWHZ is defined as the time at which the outputs achieve the high impedance state. It is not referenced to output voltage levels. 9. /CS1 in high for the standby, low for active. /UB and /LB in high for the standby, low for active. 10. Do not input data to the I/O pins while they are in the output state. Revision 1.7 March. 2002 8 HY64UD16162M Series AVOID TIMING Hynix 1T/1C SRAM has a timing which is not supported at read operation. If your system has multiple invalid address signal shorter than tRC during over 10us at read operation which showed in abnormal timing, Hynix 1T/1C SRAM needs a normal read timing at least during 10us which showed in avoidable timing(1) or toggle the /CS1 to high(≥tRC) one time at least which showed in avoidable timing(2) ABNORMAL TIMING /CS1 ≥ 10us /WE < tRC ADD AVOIDABLE TIMING(1) /CS1 ≥ 10us /WE ≥ tRC ADD ≥ tRC AVOIDABLE TIMING(2) /CS1 ≥ 10us /WE < tRC ADD Revision 1.7 March. 2002 9 HY64UD16162M Series PACKAGE DIMENSION 48ball Fine Pitch Ball Grid Array Package(F) BOTTOM BOTTOM VIEW VIEW TOP TOP VIEW VIEW A1 CORNER INDEX AREA A1 INDEX MARK B1 B A A A B C C D C1 E F C/2 G H 6 5 4 3 2 1 B/2 SIDE SIDE VIEW VIEW 5 E1 E C E2 SEATING PLANE A 4 R 3 D(DIAMETER) unit : mm NOTE. Symbol Min. Typ. Max. A B 6.90 0.75 7.00 7.10 B1 C 7.90 3.75 8.00 8.10 3. DIMENSION “D” IS MEASURED AT THE MAXIMUM SOLDER BALL DIAMETER IN A PLANE PARALLEL TO DATUM C. C1 D 0.30 5.25 0.35 0.40 4. PRIMARY DATUM C(SEATING PLANE) IS DEFINED BY THE CROWN OF THE SOLDER BALLS. E - 1.00 1.10 E1 E2 0.20 0.75 0.25 0.30 R - - 0.08 Revision 1.7 March. 2002 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994. 2. ALL DIMENSIONS ARE MILLIMETERS. 5. THIS IS A CONTROLLING DIMENSION. 10 HY64UD16162M Series MARKING INFORMATION Package FBGA Marking Example H Y U D c s s t x x x x 1 6 1 6 2 M y y w w p K O R x Index • • • HYUD16162M HY U D 16 16 2 M : : : : : : : : Part Name HYNIX Power Supply Tech. + Classification Bit Organization Density Mode Version c ss : Power Consumption : Speed : : : : : : 3.0V(2.7V~3.3V) 1T+1C x16 16M 1CS with /UB,/LB;tCS 1st Generation : D – Low Low Power : 70 – 70ns 85 – 85ns : E – Extended(-25 ~ 85 ° C) I – Industrial(-40 ~ 85 ° C) • t : Temperature • yy • ww • p : Year (ex : 01 = year 2001, 02= year 2002) : Work Week ( ex : 12 = work week 12 ) : Process Code • xxxxx : Lot No. • KOR : Origin Country Note - Capital Letter - Small Letter Revision 1.7 March. 2002 : Fixed Item : Non-fixed Item 11