MICREL SY55852UKI

SuperLite™
Micrel, Inc.
SY55852U
SuperLite™
SY55852U
D FLIP-FLOP
FEATURES
■
■
■
■
■
■
■
■
■
2.5GHz min. fMAX
2.3V to 5.7V power supply
Single bit register memory
Synchronizes 1 bit of data to a clock
Optimized to work with SuperLite™ family
Fully differential
Accepts CML, PECL, LVPECL input logic levels
Source terminated CML outputs for fast edge rates
Available in a tiny 10-pin MSOP
SuperLite™
DESCRIPTION
The SY55852U is a flip-flop used to synchronize data
to a clock. Its differential output will reproduce and
remember the value on its input at the rising edge of the
clock. In addition, an asynchronous, level sensitive reset
is provided. For a synchonous reset, the SY55851U
AnyGate™ can be used.
SY55852U inputs can be terminated with a single
resistor between the true and complement pins of a given
input.
The SY55852U is a member of Micrel's SuperLite™
family of high-speed CML logic. This family features very
small packaging and 2.3V to 5.7V operation.
FUNCTIONAL BLOCK DIAGRAM
APPLICATIONS
■ High-speed logic
■ OC-48 communication systems
DATA
D
Q
OUT
CLOCK
R
RESET
SuperLite is a trademark of Micrel, Inc.
M9999-110705
[email protected] or (408) 955-1690
Rev.: D
1
Amendment: /0
Issue Date: November 2005
SuperLite™
SY55852U
Micrel, Inc.
PACKAGE/ORDERING INFORMATION
VCC /R
9
10
R
8
Q
7
Ordering Information(1)
/Q
6
Top View
MSOP
1
D
4
5
2
3
/D CLK /CLK GND
Part Number
Package
Type
Operating
Range
Package
Marking
Lead
Finish
SY55852UKC
55852U
Sn-Pb
K10-1
Commercial
SY55852UKCTR(2)
K10-1
Commercial
55852U
Sn-Pb
SY55852UKI
K10-1
Industrial
55852U
Sn-Pb
SY55852UKITR(2)
K10-1
Industrial
55852U
Sn-Pb
SY55852UKG(3)
K10-1
Industrial
55852U with
NiPdAu
Pb-Free bar line indicator Pb-Free
SY55852UKGTR(2, 3)
K10-1
Industrial
55852U with
NiPdAu
Pb-Free bar line indicator Pb-Free
10-Pin MSOP (K10-1)
Notes:
1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only.
2. Tape and Reel.
3. Pb-Free package recommended for new designs.
PIN DESCRIPTION
Pin Number
Pin Name
1, 2
D, /D
3, 4
CLK, /CLK
Pin Function
CML/PECL/LVPECL Input (Differential): This is the single bit of data that gets clocked
in and remembered.
CML/PECL/LVPECL Input (Differential): The rising edge of this signal is the clock
signal that determines when the Boolean value at the data input gets stored.
5
GND
Ground.
6, 7
Q, /Q
CML Output (Differential): This is the output of the flip-flop.
8, 9
R, /R
CML/PECL/LVPECL Input (Differential): This is an asynchronous active high level
reset, that forces the flip-flop into a known state, namely zero.
10
VCC
Power Supply.
TRUTH TABLE
D
CLK
R
Q
/Q
X
X
1
0
1
X
0
0
QN-1
/QN-1
X
1
0
QN-1
/QN-1
0
0
0
1
1
0
1
0
M9999-110705
[email protected] or (408) 955-1690
2
SuperLite™
SY55852U
Micrel, Inc.
FUNCTIONAL DESCRIPTION
Establishing Static Logic Inputs
The true pin of an input pair is internally biased to ground
through a 75kΩ resistor. The complement pin of an input
pair is internally biased halfway between VCC and ground
by a voltage divider consisting of two 75kΩ resistors. To
keep an input at static logic zero at VCC > 3.0V, leave both
inputs unconnected. For V CC ≤ 3.0V, connect the
VCC
X
NC
/X
complement inputs to VCC and leave the true inputs
unconnected. To make an input static logic one, connect
the true input to V CC , leave the complement input
unconnected. These are the only safe ways to cause inputs
to be at a static value. In particular, no input pin should be
directly connected to ground. All NC (no connect) pins
should be unconnected.
NC
X
NC
/X
VCC > 3.0V
Figure 1. Hard Wiring a Logic “1” (1)
Note 1.
X is either D, CLK, R input. /X is either /D, /CLK, /R input.
NC
X
VCC
/X
VCC ≤ 3.0V
Figure 2. Hard Wiring a Logic “0” (1)
M9999-110705
[email protected] or (408) 955-1690
3
SuperLite™
SY55852U
Micrel, Inc.
Absolute Maximum Ratings(Note 1)
Operating Ratings(Note 2)
Supply Voltage (VCC) .................................. –0.5V to +6.0V
CML Output Voltage .......................... VCC –1.0 to VCC +0.5
Lead Temperature (soldering, 20 sec.) ..................... 260°C
Storage Temperature (TS) ....................... –65°C to +150°C
Supply Voltage (VIN) .............................. –0.5 to VCC +0.5V
Ambient Temperature (TA) ......................... –40°C to +85°C
Package Thermal Resistance
MSOP (θJA)
Still-Air ........................................................... 113°C/W
500lpfm ............................................................ 96°C/W
Note 1.
Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is
not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratlng
conditions for extended periods may affect device reliability.
Note 2.
The data sheet limits are not guaranteed if the device is operated beyond the operating ratings.
DC ELECTRICAL CHARACTERISTICS(Note 1)
VCC = +2.3V to +5.7V; GND = 0V; TA = –40°C to +85°C; unless otherwise noted.
Symbol
Parameter
VCC
Power Supply Voltage
ICC
Power Supply Current
Note 1.
Condition
Min
Typ
2.3
Max
Units
5.7
V
36
mA
The device is guaranteed to meet the DC specifications, shown in the table above, after thermal equilibrium has been established. The device
is tested in a socket such that transverse airflow of ≥500lfpm is maintained.
CML DC ELECTRICAL CHARACTERISTICS(Note 1)
VCC = +2.3V to +5.7V; GND = 0V; TA = –40°C to +85°C; unless otherwise noted.
Symbol
Parameter
Condition
Min
Typ
Max
VID
Differential Input Voltage
VIH
Input HIGH Voltage
Note 2
1.6
—
VCC
V
VIL
Input LOW Voltage
Note 2
1.5
—
VCC – 0.1
V
VOH
Output HIGH Voltage
No Load
VCC – 0.020 VCC – 0.010
VCC
V
VOL
Output LOW Voltage
No Load
VCC – 0.97 VCC – 0.825 VCC – 0.660
VOS
Output Voltage Swing
No Load, Note 3
50Ω Environment, Note 4
100Ω Environment, Note 5
RDRIVE
Output Source Impedance
100
Units
mV
V
0.660
0.800
0.400
0.200
0.950
V
V
V
80
100
120
Ω
Note 1.
Equilibrium temperature.
Note 2.
Inputs must be biased to logic LOW or HIGH when VCC is less than 3.0V.
Note 3.
Actual voltage levels and differential swing will depend on customer termination scheme. Typically, a 400mV swing is available in the 100Ω
environment and a 200mV swing in the 50Ω environment. Refer to the “CML Termination” diagram for more details.
Note 4.
See Figure 3a and 3b.
Note 5.
See Figure 4.
M9999-110705
[email protected] or (408) 955-1690
4
SuperLite™
SY55852U
Micrel, Inc.
AC ELECTRICAL CHARACTERISTICS(Note 1)
VCC = 2.3V to 5.7V; GND = 0V; TA = –40°C to +85°C; unless noted.
Symbol
Parameter
Condition
Min
fMAX
Max. Operating Frequency
tpd
Propagation Delay
tS
Set-Up Time
40
ps
tH
Hold Time
40
ps
tRR
Reset Recovery
400
ps
tPW
Minimum Pulse Width
160
140
250
ps
Note 1.
CLK to Q
R to Q
CLK to Q
VCC < 3V
VCC ≥ 3V
35
Tested using environment of Figure 3b, 50Ω load CML output.
TIMING DIAGRAMS
CLK
tH
50%
DATA
tS
tRR
RESET
Q
50%
tpd
M9999-110705
[email protected] or (408) 955-1690
50%
tpd
5
Units
GHz
400
500
CML Output Rise/Fall Times
(20% to 80%)
50%
Max
2.5
R to Q
tr,tf
Typ
150
ps
ps
SuperLite™
SY55852U
Micrel, Inc.
CML TERMINATION
All inputs accept the output from any other member of
this family. All outputs are source terminated 100Ω CML
differential drivers as shown in Figures 3 and 4. SY55852U
expects the inputs to be terminated, and that good high
vcc
100Ω
speed design practices be adhered to. SY55852U inputs
are designed to accept a termination resistor between the
true and complement inputs of a differential pair. 0402 form
factor chip resistors will fit with some trace fanout.
vcc
vcc
100Ω
100Ω
100Ω
50Ω
100Ω
100Ω
100Ω
50Ω
100Ω
100Ω
50Ω
50Ω
50Ω
8mA
8mA
SY55852U
SY55852U
Figure 3a. Differentially Terminated
(50Ω Load CML Output)
Figure 3b. Individually Terminated
(50Ω Load CML Output)
VCC
100Ω
100Ω
100Ω
200Ω
100Ω
8mA
SY55852U
Figure 4.
M9999-110705
[email protected] or (408) 955-1690
100Ω Load CML Output
6
50Ω
SuperLite™
SY55852U
Micrel, Inc.
10-PIN MSOP (K10-1)
Rev. 00
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131
TEL
+ 1 (408) 944-0800
FAX
+ 1 (408) 474-1000
WEB
USA
http://www.micrel.com
The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use.
Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can
reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into
the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s
use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify
Micrel for any damages resulting from such use or sale.
© 2005 Micrel, Incorporated.
M9999-110705
[email protected] or (408) 955-1690
7