ALUMINUM ELECTROLYTIC CAPACITORS WS Chip Type, High CV High Temperature (260°C) Reflow series Corresponding with 260°C peak reflow soldering Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec. 2 times (φ8 × 6.2, φ10 × 10 : 1 time) Chip type higher capacitance in large case size. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2002/95/EC). WS High Temperature Reflow UR Specifications Item Performance Characteristics – 40 to +85°C 6.3 to 50V 22 to 1500µF ± 20% at 120Hz, 20°C After 1 minute's application of rated voltage, leakage current is not more than 0.03CV (µA) . Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current Measurement frequency : 120Hz, Temperature : 20°C Tangent of loss angle (tan δ) Rated voltage (V) tan δ (MAX.) 6.3 0.28 10 0.24 16 0.20 25 0.16 35 0.14 50 0.12 Measurement frequency: 120Hz 35 2 3 25 2 4 16 3 6 10 4 8 6.3 5 10 Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C Stability at Low Temperature 50 2 3 Within ±20% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 85°C. Shelf Life After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20°C. Marking Black print on the case top. 1 (φ6.3, φ8 × 6.2) 1 Size φ8 × 6.2 only 5 6 7 8 9 10 11 12 13 14 Package code Configuration Capacitance tolerance (±20%) Rated capacitance (100µF) A±0.2 L ±0.3 Capacitance 4 A±0.2 B±0.2 φD±0.5 N2 100A WS Series Positive C±0.2 3 0.5MAX. Plastic platform 0.3MAX. 2 UWS 1 A 1 0 1 M C L 1G S E Voltage (A:10V) Lot No. Within ±10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value Type numbering system (Example : 10V 100µF) Chip Type 1 Trade mark Capacitance change tan δ Leakage current H Rated voltage (10V) Series name Negative Type (mm) φD×L (φ8 × 10, φ10 × 10) A±0.2 A B C E L H 6.3 × 7.7 8 × 6.2 8 × 10 10 × 10 2.4 6.6 6.6 2.2 5.8 0.5 to 0.8 2.4 6.6 6.6 2.2 7.7 0.5 to 0.8 3.3 8.3 8.3 2.3 6.2 0.5 to 0.8 2.9 8.3 8.3 3.1 10 0.8 to 1.1 3.2 10.3 10.3 4.5 10 0.8 to 1.1 A±0.2 L±0.5 Capacitance Lot No. C±0.2 B±0.2 Trade mark φD±0.5 N2 100V WS Series E Voltage (V:35V) 0.5MAX. Positive Plastic platform 0.3MAX. 6.3 × 5.8 Negative H Voltage V 6.3 10 16 25 35 50 Code j A C E V H Dimension table in next page. CAT.8100Z ALUMINUM ELECTROLYTIC CAPACITORS WS series Dimensions V Cap. (µF) Code 6.3 10 16 25 35 50 0J 1A 1C 1E 1V 1H 22 220 33 330 47 470 100 101 6.3 × 5.8 070 8 × 6.2 150 151 6.3 × 5.8 085 220 221 8 × 6.2 160 8 × 6.2 330 331 8 × 6.2 190 470 471 8 × 10 680 681 8 × 10 1000 102 1500 152 6.3 × 5.8 045 6.3 × 5.8 055 8 × 6.2 095 6.3 × 5.8 065 8 × 6.2 105 8 × 10 140 125 8 × 6.2 145 8 × 10 175 10 × 10 195 6.3 × 7.7 151 8 × 10 192 8 × 10 214 10 × 10 238 175 8 × 10 215 10 × 10 250 10 × 10 265 10 × 10 289 8 × 10 240 8 × 10 270 10 × 10 305 10 × 10 324 265 8 × 10 290 10 × 10 330 10 × 10 393 318 10 × 10 374 10 × 10 396 10 × 10 400 10 × 10 454 10 × 10 489 Case size φ D × L (mm) Rated ripple Rated ripple current (mArms) at 85°C 120Hz Frequency coefficient of rated ripple current Cap.(µF) Frequency 00 Less than 47V 100 to 1500 50 Hz 0.80 0.85 120 Hz 1.00 1.00 300 Hz 1.15 1.08 1 kHz 1.40 1.20 10 kHz or more 1.67 1.30 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100Z