TL714C HIGH-SPEED DIFFERENTIAL COMPARATOR SLCS015 – DECEMBER 1988 – REVISED JUNE 1989 D D D D D D OR P PACKAGE (TOP VIEW) Operates From a 5-V Supply Self-Biasing Inputs Hysteresis . . . 10 mV Typ Response Time . . . 6 ns Typ Maximum Operating Frequency 50 MHz Typ NC IN – IN+ NC 1 8 2 7 3 6 4 5 VCC NC OUT GND NC — No internal connection description The TL714C is a high-speed differential comparator fabricated with bipolar Schottky process technology. The circuit has differential inputs and a TTL-compatible logic output with symmetrical switching characteristics. symbol IN+ OUT IN – The device operates from a single 5-V supply and is useful as a disk-memory read-chain data comparator. The TL714C is characterized for operation from 0°C to 70°C. schematic of inputs and outputs EACH INPUT OUTPUT VCC 50 Ω VCC 100 Ω 9.6 kΩ IN OUT 9.6 kΩ GND All resistor values shown are nominal. Copyright 1989, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 TL714C HIGH-SPEED DIFFERENTIAL COMPARATOR SLCS015 – DECEMBER 1988 – REVISED JUNE 1989 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 5 V Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC to GND Low-level output current, IOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C Lead temperature1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C † Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the recommended operating conditions section of this specification is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltage, are with respect to the network ground. 2. Differential voltage values are at IN+ with respect to IN –. DISSIPATION RATING TABLE PACKAGE TA ≤ 25°C POWER RATING DERATING FACTOR DERATE ABOVE TA TA = 75°C POWER RATING D P 500 mW 500 mW 5.8 mW/°C N/A 64°C N/A 464 mW 500 mW recommended operating conditions Supply voltage, VCC MIN MAX UNIT 4.75 5.25 V 1.4 to VCC – 1.4 Common-mode input voltage, VIC V High-level output current, IOH –1 mA Low-level output current, IOL 16 mA 70 °C Operating free-air temperature, TA 0 electrical characteristics over free-air operating temperature range, VCC = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS VIC = 1.4 V to 3.6 V MIN –75§ TYP‡ 2 10 2.7 3.4 VT Vhys Threshold voltage (VT+ – VT–) VOH VOL High-level output voltage IOS ri Short-circuit output current – 30 Differential input resistance 2.9 Hysteresis (VT+ – VT–) VID = 100 mV, VID = – 100 mV, Low-level output voltage IOH = – 1 mA IOL = 16 mA 0.4 MAX UNIT 75 mV 30 mV V 0.5 – 110 V mA kΩ ICC Supply current VID = –100 mV, IO = 0 7 12 mA ‡ All typical values are at TA = 25°C. § The algebraic convention, where the more negative limit is designated as minimum, is used in this data sheet for input threshold voltage levels only. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL714C HIGH-SPEED DIFFERENTIAL COMPARATOR SLCS015 – DECEMBER 1988 – REVISED JUNE 1989 switching characteristics, VCC = 5 V, TA = 25°C PARAMETER TEST CONDITIONS fmax Maximum operating frequency tPLH tPHL Propagation delay time, low-to-high-level output Propagation delay time, high-to-low-level output tr Rise time tf Fall time † All typical values are at TA = 25°C. MIN VID = ± 250 mV, CL = 25 pF, tr = tf = 4 ns, Input duty cycle = 50% VID = ± 100 mV,, See Figures 1 and 2 CL = 25 pF,, VID = ± 100 mV, See Figure 3 CL = 25 pF, TYP† MAX 50 UNIT MHz 6 12 ns 6 12 ns 4 8 ns 4 8 ns PARAMETER MEASUREMENT INFORMATION tr ≤ 4 ns VID tf ≤ 4 ns 100 mV 90% 50% 10% –100 mV tPLH VOH 1.4 V VO VOL Figure 1. Propagation Delay Time, Low to High (tPLH) 90% –100 mV VOH 1.4 V VO VOL Figure 2. Propagation Delay Time, High to Low (tPHL) tr ≤ 4 ns VID 100 mV 90% 50% 10% tPHL VID tf ≤ 4 ns 100 mV 90% 10% 10% –100 mV tr 2.4 V tf 2.4 V VOH VO 0.5 V 0.5 V VOL Figure 3. Rise and Fall Times (tr, tf) POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated