ONSEMI MC10H604FNR2

SEMICONDUCTOR TECHNICAL DATA
The MC10H/100H604 is a 6–bit, registered, dual supply TTL to ECL
translator. The device features differential ECL outputs as well as a choice
between either a differential ECL clock input or a TTL clock input. The
asynchronous master reset control is an ECL level input..
With its differential ECL outputs and TTL inputs the H604 device is ideally
suited for the transmit function of a HPPI bus type board–to–board interface
application. The on chip registers simplify the task of synchronizing the data
between the two boards.
The device is available in either ECL standard: the 10H device is
compatible with MECL 10KH logic levels while the 100H device is
compatible with 100K logic levels.
•
•
•
•
•
Differential 50Ω ECL Outputs
Choice Between Differential ECL or TTL Clock Input
Dual Power Supply
Multiple Power and Ground Pins to Minimize Noise
Specified Within–Device Skew
PIN NAMES
PIN
LOGIC SYMBOL
1 OF 6 BITS
Dn
D
Q
FN SUFFIX
PLASTIC PACKAGE
CASE 776–02
Qn
Qn
FUNCTION
TTL Data Inputs
Differential ECL Clock Input
TTL Clock Input
ECL Master Reset Input
True ECL Outputs
Inverted ECL Outputs
ECL VCC (0V)
TTL VCC (+5.0V)
ECL VEE (–5.2V)
D0–D5
CLK, CLK
TCLK
MR
Q0–Q5
Q0–Q5
VCCE
VCCT
VEE
TRUTH TABLE
CLK
R
Dn
MR
TCLK/CLK
Qn+1
L
H
X
L
L
H
Z
Z
X
L
H
L
Z = LOW to HIGH Transition
CLK
CLK
TCLK
Pinout: 28–Lead PLCC (Top View)
*
D1 D2 VCCT D3
25
MR
VBB
*
24
23
22
D4
D5 VCCE
21
20
26
18
Q5
TCLK
27
17
Q5
VBB
28
16
Q4
15
Q4
CLK
2
14
VCCE
MR
3
13
Q3
VCCE
4
12
Q3
CLK
1. When using MECL inputs, TCLK must be tied to ground (0V).
2. When using only one MECL input, the unused MECL input must be tied
to VBB, and TCLK must be tied to ground (0V).
3. When using TCLK, both MECL inputs must be tied to VEE (–5.2V).
5
6
7
8
9
10
Q0 Q0 VEE Q1 Q1 Q2
9/96
 Motorola, Inc. 1996
19
D0
2–302
REV 1
11
Q2
MC10H604 MC100H604
DC CHARACTERISTICS: VEE = VEE(Min) to VEE(Max); VCCE = GND; VCCT = 5.0V +10%
0°C
S b l
Symbol
Min
P
Parameter
IEE
ECL Power Supply Current
ICCH
ICCL
TTL Power Supply Current
25°C
Max
10H
100H
Min
85°C
Max
Min
Max
U i
Unit
130
130
130
140
130
150
mA
35
45
35
45
35
45
mA
Max
U i
Unit
145
µA
µA
C di i
Condition
10H ECL DC CHARACTERISTICS: VCCT = +5.0 V ± 10%; VEE = – 5.20 V ±5%
0°C
S b l
Symbol
Min
P
Parameter
25°C
Max
Min
85°C
Max
225
Min
145
C di i
Condition
IIH
IIL
Input HIGH Current
Input LOW Current
0.5
VIH
VIL
Input HIGH Voltage
Input LOW Voltage
–1170
–1950
–840
–1480
–1130
–1950
–810
–1480
–1060
–1950
–720
–1480
mV
VBB
Output Bias Voltage
–1400
–1290
–1370
–1270
–1330
–1210
mV
VOH
VOL
Output HIGH Voltage
Output LOW Voltage
–1020
–1950
–840
–1630
–980
–1950
–810
–1630
–910
–1950
–720
–1595
mV
50 Ω to – 2.0 V
Max
U i
Unit
C di i
Condition
145
µA
µA
0.5
0.5
100H ECL DC CHARACTERISTICS: VCCT = 5.0 V ± 10%; VEE = – 4.2 V to – 5.5 V
0°C
S b l
Symbol
Min
P
Parameter
25°C
Max
Min
85°C
Max
225
Min
IIH
IIL
Input HIGH Current
Input LOW Current
0.5
145
VIH
VIL
Input HIGH Voltage
Input LOW Voltage
–1165
–1810
–880
–1475
–1165
–1810
–880
–1475
–1165
–1810
–880
–1475
mV
VBB
Output Bias Voltage
–1400
–1280
–1400
–1280
–1400
–1280
mV
VOH
VOL
Output HIGH Voltage
Output LOW Voltage
–1025
–1810
–880
–1620
–1025
–1810
–880
–1620
–1025
–1810
–880
–1620
mV
0.5
0.5
50 Ω to – 2.0 V
TTL DC CHARACTERISTICS: VCCT = 5.0 V ± 10%; VEE = – 5.2 V ± 5% (10H version); VEE = – 4.2 V to – 5.5 V (100H version)
0°C
S b l
Symbol
Min
P
Parameter
VIH
VIL
Input HIGH Voltage
Input LOW Voltage
IIH
25°C
Max
Min
2.0
85°C
Max
2.0
Min
Max
U i
Unit
V
V
2.0
C di i
Condition
0.8
0.8
0.8
Input HIGH Current
20
100
20
100
20
100
µA
VIN = 2.7 V
VIN = 7.0 V
IIL
Input LOW Current
– 0.6
– 0.6
– 0.6
mA
VIN = 0.5 V
VIK
Input Clamp Voltage
–1.2
–1.2
–1.2
V
IIN = –18 mA
AC CHARACTERISTICS: VCCT = 5.0 V ± 10%; VEE = – 5.2 V ± 5% (10H version); VEE = – 4.2 V to – 5.5 V (100H version)
0°C
P
Parameter
Min
tPLH
tPHL
Propagation Delay CLK to Q
to Output
TCLK to Q
MR to Q
1.5
2.0
1.5
ts
Setup Time
1.5
0.5
1.5
0.5
1.5
tH
Hold Time
1.5
0.5
1.5
0.5
1.5
tPW
Minimum Pulse Width
CLK, MR
Minimum Input Swing
tr
tf
Rise/Fall Times
MECL Data
DL122 — Rev 6
Max
Min
3.5
4.0
4.0
1.5
2.0
1.5
1.0
Typ
85°C
S b l
Symbol
VPP
Typ
25°C
Max
Min
3.5
4.0
4.0
1.5
2.0
1.5
1.0
Typ
Max
U i
Unit
3.5
4.0
4.0
ns
CL = 50pF
0.5
ns
CL = 50pF
0.5
ns
CL = 50pF
ns
CL = 50pF
1.0
150
0.3
1.0
2.0
0.3
2–303
1.0
C di i
Condition
mV
2.0
0.3
1.0
2.0
ns
20% – 80%
MOTOROLA
MC10H604 MC100H604
OUTLINE DIMENSIONS
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 776–02
ISSUE D
0.007 (0.180)
B
T L–M
M
N
S
T L–M
S
S
Y BRK
–N–
0.007 (0.180)
U
M
N
S
D
Z
–M–
–L–
W
28
D
X
G1
0.010 (0.250)
T L–M
S
N
S
S
V
1
VIEW D–D
A
0.007 (0.180)
R
0.007 (0.180)
M
T L–M
S
N
S
C
M
T L–M
S
N
0.007 (0.180)
H
Z
M
T L–M
N
S
S
S
K1
E
0.004 (0.100)
G
J
S
K
SEATING
PLANE
F
VIEW S
G1
0.010 (0.250)
–T–
T L–M
S
N
S
M
T L–M
S
N
S
VIEW S
NOTES:
1. DATUMS –L–, –M–, AND –N– DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM –T–, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE
MOLD FLASH. ALLOWABLE MOLD FLASH IS
0.010 (0.250) PER SIDE.
4. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR
BURRS, GATE BURRS AND INTERLEAD
FLASH, BUT INCLUDING ANY MISMATCH
BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).
MOTOROLA
0.007 (0.180)
2–304
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
INCHES
MIN
MAX
0.485
0.495
0.485
0.495
0.165
0.180
0.090
0.110
0.013
0.019
0.050 BSC
0.026
0.032
0.020
–––
0.025
–––
0.450
0.456
0.450
0.456
0.042
0.048
0.042
0.048
0.042
0.056
–––
0.020
2_
10_
0.410
0.430
0.040
–––
MILLIMETERS
MIN
MAX
12.32
12.57
12.32
12.57
4.20
4.57
2.29
2.79
0.33
0.48
1.27 BSC
0.66
0.81
0.51
–––
0.64
–––
11.43
11.58
11.43
11.58
1.07
1.21
1.07
1.21
1.07
1.42
–––
0.50
2_
10_
10.42
10.92
1.02
–––
MECL Data
DL122 — Rev 6
MC10H604 MC100H604
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
Mfax: [email protected] – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
◊
MECL Data
DL122 — Rev 6
2–305
*MC10H604/D*
MC10H604/D
MOTOROLA