SC804 Fully Integrated Lithium-Ion Battery Charger System with Timer PRELIMINARY POWER MANAGEMENT Description Features Fully integrated charger with FET pass transistor, reverse-blocking diode, sense resistor, timer, and thermal protection The SC804 is a fully integrated full-feature, single cell constant-current/constant-voltage (CC/CV) Lithium-Ion battery charger. With an integrated timer and complete charge control algorithm, the SC804 is ideal for standalone charger applications. The SC804 contains programmable pre-charge, fast-charge and termination current settings. The SC804 can be programmed to terminate charging based on the output current or the time-out of the programmable timer. The fast charge current is typically set with an external resistor, but it can also be adjusted by applying an analog voltage to the AFC pin. This feature allows use of a micro controller to set charging current via a DAC output. Battery voltage controlled to 1% accuracy Programmable pre charge, fast charge & termination current over wide range, with analog current control reference input for design flexibility Up to 1.5A continuous charge current Input voltage range from 3V to 14V Soft-start reduces start-of-charge adapter load transients NTC thermistor sense input and adjustable cold temperature threshold The SC804’s 14V input voltage range eliminates the need for additional protection circuitry required by other 5V chargers to protect against faulty adapters. The SC804 also incorporates an under-voltage lockout falling threshold of 3V so that charging will continue if the input supply goes into a current-limited mode. Adjustable 2 - 6 hour programmable charge timer 0.1μA battery drain current in shutdown and monitor modes Small 4mm x 4mm 16 lead MLPQ package Over-current protection in all modes Over-voltage protection Reference ground and battery sense inputs are provided to eliminate voltage drops during charging due to high charging currents. Remote Kelvin sensing at the battery terminals Status indicators for charger-present, charger-active, over-voltage fault, and error notification The output voltage to the battery is controlled to within 1% of the programmed voltage. The SC804 can also function as a general purpose Circuit current source or as a current Typical Application source for charging nickel-cadmium (NiCd) and nickelmetal-hydride (NiMH) batteries. Applications Typical Application Circuit Charger VIN C1 2.2 μF 14 OV_FLT R3 RT NTC R1 ERROR July 18, 2007 R2 Handheld computers Digital cameras Programmable current source Cellular phones PDAs Handheld meters Charging stations VCC CPB 13 OVPB CHRGB 3 RTIM IPRGM 7 CTO NTC 4 BSEN ITERM 8 VOUT FLTB 6 VOUT GND 5 AFC RGND SC804 11 10 12 2 1 16 15 9 Red R5 Battery Green R6 C2 2.2μF R4 DAC ISET 1 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Absolute Maximum Ratings Exceeding the specifications below may result in permanent damage to the device or device malfunction. Operation outside of the parameters specified in the Electrical Characteristics section is not implied. Parameter Symbol Maximum Units VCC, CTO, NTC to GND -0.3 to 14.0 V VOUT, BSEN, RTIM, AFC, IPRGM, CPB, CHRGB, OVPB, ITERM, FLTB, to GND -0.3 to +6.0 V RGND to GND -0.3 to 0.3 V IVOUT 1.5 A Power Dissipation MLP (Derate 20mW/°C above 85°C) Pd 2 W Thermal Impedance, Junction to Ambient(1) θJA 48 °C/W Junction Temperature TJ 150 °C Operating Ambient Temperature Range TA -40 to +85 °C IR Reflow Temperature TLEAD 260 °C Storage Temperature Range TSTG -65 to 150 °C VOUT Output Current VOUT short to GND Continuous ESD Protection Level(2) V ESD 2 kV Notes: 1) Calculated from package in still air, mounted to 3” x 4.5”, 4 layer FR4 PCB with thermal vias under the exposed pad per JESD51 standards. 2) Tested according to JEDEC standard JESD22-A114-B. Electrical Characteristics Unless otherwise noted: VCC = 4.75V - 5.25V. Typical values are at TA = 25°C Min and Max are for -40°C < TA < +85°C unless noted. Parameter Symbol Conditions Min Typ Max Units 4.2 5.0 6.1(1) V Operating Voltage VCCOP VCC UVLO Rising Threshold VTUVLOR Charging begins when threshold is exceeded 3.8 4.0 4.2 V VCC UVLO Falling Threshold VTUVLOF Charging continues until threshold is reached 2.8 3.0 3.2 V VCC OVP Rising Threshold VTOVPR 6.5 6.8 7.25 V VCC OVP Falling Threshold VTOVPF 6.1 6.5 6.85 V VCC OVP Hysteresis VTOVPH 200 350 600 mV ICCDIS Shutdown Mode - CHRGB, CPB, OVPB, FLTB off NTC = 0V 1.9 ICCCHG Charging Mode - CHRGB, CPB, OVPB, FLTB off NTC = 2.5V 2.0 Operating Current © 2007 Semtech Corp. 2 mA www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Electrical Characteristics (Cont.) Parameter Symbol Conditions Battery Leakage Current (VOUT and BSEN) ILEAKBAT VCC = 0V, VOUT = BSEN = 4.5V VCV 0°C ≤ TJ ≤ 125°C RGND Output Accuracy VOUT = VOUTNOM + ∆RGND VRGND RGND - GND = 30mV RGND Current IRGND RGND = 0V Battery Pre-Charge Current IPREQ RITERM = 499Ω, 0°C ≤ TJ ≤ 125°C 270 300 330 mA Battery Termination Current ITERM RITERM = 499Ω, 0°C ≤ TJ ≤ 125°C 270 300 330 mA Battery Fast-Charge Current IFAST RPRGM = 1.87kΩ, VOUT = 3.8V 0°C ≤ TJ ≤ 125°C 740 800 860 mA AFC DAC Fast-Charge Current IDACADJ RPRGM = 1.87kΩ, V(AFC) = 0.75V 0°C ≤ TJ ≤ 125°C 360 400 440 mA AFC Enable/Disable Threshold VTAFC VCC - VAFC > VTAFC disables Analog Fast Charge ITERM Regulated Voltage VITERM 1.4 1.5 1.6 V IPROG Regulated Voltage VIPRGM 1.4 1.5 1.6 V VBAT Pre-Charge Threshold VTPreQ 0°C ≤ TJ ≤ 125°C 2.8 2.9 3.0 V VBAT Recharge Threshold VTReQ VCV - VBSEN, 0°C ≤ TA ≤ 85°C 60 100 140 mV TOT Hysteresis = 10°C Regulated Constant Voltage Over-Temperature Shutdown © 2007 Semtech Corp. 3 Min Typ Max Units 0.1 2 μA 4.16 4.20 4.24 V 22 30 38 mV 35 μA 1 150 V °C www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Electrical Characteristics (Cont.) Parameter Symbol Conditions Min Typ Max Units VTNTCDIS SC804 Disabled 0.3 0.6 0.8 V 29 30 31 VTNTCH NTC Hot VTH Applies to falling threshold 4.3V ≤ VCC ≤ 6.5V % of VCC at VCC = 5V 1.45 1.50 1.55 V NTC Cold VTH, VCTO = 0V Applies to rising threshold 4.3V ≤ VCC ≤ 6.5V 73.4 74.4 75.4 % of VCC at VCC = 5V 3.67 3.72 3.77 V VTNTCC NTC Thresholds VTNTCHYS VCTO VTCTOHYS Adjust Mode BSEN Voltage VBSEN-ADJ NTC Hot & Cold VTNTCx hysteresis (VTNTCx Rising - VTNTCx Falling) Applies to internal NTC thresholds mV CTO Voltage (Adjustable NTC Cold Rising Threshold) Setting Range(2), -40°C ≤ TA ≤ 25°C (NTC Cold Rising Threshold is VTNTCC when CTO tied to GND) 50 90 % of VCC Threshold Error(3), -40°C ≤ TA ≤ 25°C -70 70 mV Internal hysteresis on CTO (VCTO Rising - VCTO Falling) Applies to externally set NTC cold threshold 3.5V ≤ VOUT ≤ VCC - 150mV 0°C ≤ TJ ≤ 125°C Adjust Mode Enable Voltage, VOUT-BSEN VADJEN 3.5V ≤ VOUT ≤ VCC - 150mV Adjust Mode Disable Voltage, VOUT-BSEN VADJDIS 3.5V ≤ VOUT ≤ VCC - 150mV © 2007 Semtech Corp. 50 4 50 3.072 150 3.11 mV 3.134 V 400 mV mV www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Electrical Characteristics (Cont.) Parameter Symbol Conditions Min Typ Max Units VRTIM RRTIM = 37.4kΩ 1.4 1.5 1.6 V Timer Disable Threshold VTTIMER VRTIM ≤ VTTIMER disables internal timer 0.65 0.85 V Internal Timer Select VTINTTS 1.1 V External RTIM Regulation Voltage VCC-VRTIM > VTINTTS selects internal timer Pre-Charge Fault Time-Out TPreQF RRTIM = 37.4kΩ RTIM pulled to VCC -20% -35% 53 45 +20% +35% min Complete Charge Time-Out TQCOMP RRTIM = 37.4kΩ RTIM pulled to VCC -20% -35% 3.5 3.0 +20% +35% hr CHRGB On VCHRGB Load = 5mA 0.5 1 V CHRGB Off ICHRGB Leakage Current, V = 5V 1 μA CPB On VCPB Load = 5mA 1 V CPB Off ICPB Leakage Current, V = 5V 1 μA OVPB On VOVPB Load = 5mA 1 V OVPB Off IOVPB Leakage Current, V = 5V 1 μA FLTB On VFLTB Load = 5mA 1 V FLTB Off IFLTB Leakage Current, V = 5V 1 μA 0.5 0.5 0.5 Notes: 1) VCCOP Max is the “Maximum Vsupply” as defined in EIA/JEDEC Standard No. 78, paragraph 2.11. 2) The absolute voltage on CTO must not exceed 6.0V to ensure normal operation. 3) The threshold error is tested at VCTO min and max only. © 2007 Semtech Corp. 5 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT VOUT VCC OVPB 14 13 12 RTIM 2 11 CPB IPRGM 3 10 CHRGB ITERM 4 9 AFC TOP VIEW 5 6 7 8 FLTB T NTC CTO 15 GND 1 16 RGND BSEN Ordering Information VOUT Pin Configuration DEVICE PACKAGE SC804IMLTRT(1) MLPQ -16(2) SC804EVB Evaluation Board (2) Notes: 1) Available in tape and reel packaging only. A reel contains 3000 devices. 2) Available in lead-free packaging only. This product is fully WEEE and RoHS compliant. MLPQ16: 4X4 16 LEAD Pin Descriptions Descriptions Pin Pin # Pin Name 1 BSEN 2 CTO 3 IPRGM Charger current program pin for fast-charge mode. Requires a resistor to GND to program fast-charge current. 4 ITERM Charger termination current program pin. Requires a resistor to GND to program pre-charge and termination current. 5 RGND Reference ground. Connect to battery’s negative terminal for Kelvin voltage sensing, GND otherwise. Do not leave open. 6 GND Ground. 7 NTC Input for battery NTC thermistor network. Voltage between VTNTCH×VVCC, normally the hot threshold, and the CTO voltage (VTNTCC×VVCC if CTO is tied to GND), normally the cold threshold, enables charging. Voltages outside this range suspend charging and drive FLTB pin active (low). Voltage below VTNTCDIS (nominally 0.6V) disables the SC804 and resets the charge timer (with FLTB pin inactive). 8 FLTB Open drain fault indicator. Active low when a fault condition occurs. 9 AFC 10 CHRGB 11 CPB 12 RTIM 13 OVPB 14 VCC 15 VOUT Charger output. Connect to battery. 16 VOUT Charger output. Connect to battery. T THERMAL PAD © 2007 Semtech Corp. Pin Function Battery voltage sense. Connect to battery positive terminal for Kelvin voltage sensing, VOUT otherwise. Do not leave open. Cold Temperature Offset. Adjustable NTC input high voltage (cold temperature) threshold. When the pin is connected to GND the NTC high voltage threshold defaults to VTNTCC×VVCC. Analog Fast Charge input. Connect to a DAC for analog control of fast charge current level, connect to VCC to disable this feature. Do not leave open. Open drain charge status indicator. Active low when the charger is on and the output current exceeds the termination current setting, high impedance when IVOUT < ITERM. Open drain charger-present indicator. Active low when VCC exceeds UVLO. Programmable timer input pin. Connect to VCC to select the default time-out of 3 hours, connect to GND to disable timer, or connect an external resistor to GND to program the time-out period. Open drain over-voltage indicator. Active low when an input over-voltage fault occurs. Input supply pin. Connect to adapter power. Thermal-conduction pad on bottom of the package. Solder directly to the ground plane with multiple thermal vias to all other ground planes. 6 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Block Diagram 14 VCC BSEN 1 VCV (V BSEN-ADJ in Adj. Mode) AFC 9 Reference Voltages Fast-Charge Ref Pre - Charge Ref RGND CTO VT NTCC 5 2 VT NTCH Cold Threshold Offset Control GND 6 NTC 7 RTIM NTC Interface Pre-Charge On Fast-Charge On Over-Temp Under-Voltage Over-Voltage V ITERM Timer 12 15 VOUT 16 VOUT 4 ITERM 3 IPRGM 8 FLTB 13 OVPB V IPRGM CHRGB 10 CPB 11 Figure 1 - SC804 Functional Block Diagram © 2007 Semtech Corp. 7 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Applications Information General Operation Fast-Charge Mode (CC) The SC804 can be configured independently with respect to fast-charge and termination current, output voltage, and timing, depending on the application. A typical charging cycle is described below. Details on alternative applications and output programmability are covered in the individual sections. The fast-charge CC (Constant Current) mode is active when the battery voltage is above VTPreQ and less than VCV. The fast-charge current can be set to a maximum of 1.5A and is selected by the program resistor on the IPRGM pin. The voltage on this pin will represent the current through the battery, enabling a microprocessor via an analog-to-digital converter (ADC) to monitor battery current by sensing the voltage on the IPRGM pin. The equation to set the fastcharge current is given by: The charging cycle begins when the power adapter is connected to the device. The SC804 performs glitch filtering on the VCC input and initiates a charge cycle when VVCC is greater than the under-voltage lockout (UVLO) rising threshold voltage. If the battery voltage is less than the pre-charge threshold level, the SC804 will output the precharge current. Once the pre-charge threshold voltage is exceeded, the SC804 enters fast-charge constant current (CC) mode. When the battery voltage reaches its final value, the charger enters the constant voltage (CV) mode. In this mode the output current decreases as the battery continues to charge until the termination current level is reached. The CHRGB output turns off when IOUT drops below the termination current. If the charge timer is active, the SC804 continues to hold the battery in CV charge mode until the timer expires. When the timer expires the charger enters the monitor mode where the output remains off until the voltage at VOUT drops by VTReQ. At this point a new charge cycle is initiated. FCI = VIPRGM_Typ × 1000 RIPRGM The superior fast-charge current accuracy of the SC804 is obtained by use of a patented* polarity-switched (i.e., chopped) current sense amplifier to nullify current measurement offset errors. Compliance with the absolute maximum output current IVOUTMAX, allowing for current regulation tolerance, requires that RIPRGM be no smaller than 1.05kΩ nominal. RIPRGM can be as large as 11.5kΩ, for a nominal FCI as small as 130mA, but must exceed PCI by at least 80mA. Note that for a given program resistor the current through the battery in CV mode can be determined by replacing VIPRGM_Typ with the actual voltage on the IPRGM pin in the above equation. The CC current can also be modified by applying an analog voltage to the AFC pin as described below. Pre-Charge Mode Pre-charge mode is automatically enabled whenever the battery voltage is below the pre-charge threshold voltage, VTPreQ. It is used to limit the power dissipation and precondition the battery for fast charging. The pre-charge current value is determined by the resistor on the ITERM pin. The pre-charge current is programmable from 50mA to 350mA. The equation to select the pre-charge current is given by: VITERM_Typ PCI = × 100 RITERM Analog Fast Charge (AFC Pin) Many applications require more than one current setting for fast-charge. This behavior is obtained in the SC804 using the AFC function. When the AFC pin is connected to VCC the device behaves as described in the previous section. When the AFC pin is driven by an analog voltage between 0V and (VVCC-1.0)V, the SC804 automatically uses this pin voltage to set the maximum fast-charge current according to the following equation: Where VITERM_Typ designates the typical value of VITERM. When the timer is enabled there is also a maximum allowed precharge duration. If the pre-charge time exceeds 25% of the total charge cycle the charger will turn off due to a pre-charge fault. This fault is cleared when VCC is toggled or the output voltage rises above VTPreQ. FCI = VAFC × 1000 RIPRGM *US Patent 6,836,095. © 2007 Semtech Corp. 8 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Applications Information Charge Timer This adjustment to the fast charge current is obtained by replacing the fixed VIPRGM reference voltage with the AFC voltage. (Note that AFC voltages above VIPRGM will produce IVOUT exceeding that programmed as per the FastCharge Mode (CC) section.) For any applied AFC voltage, FCI must not drop below 130mA, and FCI must always remain at least 80mA greater than PCI. The timer on the SC804 has two functions: to protect in the event of a faulty battery and to maximize charging capacity. The RTIM pin is connected to VCC to select the internal timer, and to GND to disable the timer. Connecting a resistor between RTIM and GND will program the total charge time according to the following equation: Termination Current Charge time = Once the battery voltage reaches VCV the SC804 will transition from constant current mode to constant voltage mode. The current through the battery will decrease while the voltage remains constant as the battery becomes fully charged. When the current falls below the programmed termination current set by the termination resistor connected to the ITERM pin, the SC804 will disable CHRGB. If the timer is enabled the output will continue to float-charge in CV mode until the timer expires. If the timer is disabled, the output will turn off as soon as the termination current level is reached. The equation to set the termination current is given by: ITERM = VITERM_Typ When a charge cycle is complete, the SC804 output turns off and the device enters monitor mode. If the voltage of the battery falls below the recharge threshold (VCV - VReQ), the charger will clear the charge timer and reinitiate a charge cycle. The maximum current drain of the battery during monitor mode will be no more than 1μA over temperature. The status of the charger output as a function of the timer and IOUT is tabulated below. N/A On T > Timeout N/A Off Disabled < Itermination Off © 2007 Semtech Corp. 1 3600 This configuration is shown in the typical application schematic on page 1 of this datasheet. When the NTC voltage from the divider is greater than the high (cold) threshold or less than the low (hot) threshold, the SC804 suspends the charge cycle by turning off the output, halting (but not resetting) the charge timer, and indicating a fault on the FLTB pin. Hysteresis is included for both high and low NTC thresholds to avoid chatter at the NTC trip points. When the NTC pin voltage returns to the valid range, the SC804 automatically resumes the charge cycle. The charge timer will time-out when the SC804 output ontime exceeds the timer setting regardless of how long it has been disabled due to the NTC temperature. Monitor Mode T < Timeout × The NTC pin provides an interface to a battery pack Negative Temperature Coefficient (NTC) thermistor. The typical NTC network has a fixed resistor from VCC to the NTC pin, and the battery pack NTC thermistor connected from the NTC pin to ground. In this configuration, an increasing battery temperature produces a decreasing NTC pin voltage, and a decreasing battery temperature produces an increasing NTC pin voltage. ITERM can be programmed to be as high as 300mA or as low as 50mA, though accuracy is not guaranteed below 100mA. ITERM must be programmed to be less than FCI for correct operation of the charge cycle. Output State 3 ) NTC Interface RITERM Iout RRTIM with charge time expressed in hours. The timer is programmable over the range of 2 to 6 hours. The internal timer selection results in a charge time of 3 hours. The SC804 will automatically turn off the output when the charge timer times out. × 100 Timer ( An input voltage between VTNTCH×VVCC and the CTO input voltage VCTO (VTNTCC×VVCC if CTO is tied to GND) enables charging. An input voltage outside this range suspends charging and drives FLTB pin active (low). The internal NTC thresholds of VTNTCH and VTNTCC were designed to 9 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Applications Information (Cont.) work with standard thermistors available from numerous vendors. Step 1: Select R3. For the normal (NTC thermistor to ground) configuration, solve the NTC network voltage divider for R3 to place the NTC voltage at 0.3×VCC when RT = RHOT. VCC × RHOT 0.3 × VCC = R3 + RHOT NTC pin voltage below VTNTCDIS (nominally 0.6V) disables the SC804 and resets the charge timer (with the FLTB pin inactive). The NTC pin can be pulled down to ground by an external n-channel FET transistor or processor GPIO to disable or reset the SC804. or R3 = 2.333×RHOT = 13.624kΩ exactly. The closest 1% standard nominal value is R3 = 13.7kΩ. Note that the response of the SC804 to NTC pin voltage above the high threshold and below the low threshold is the same. Thus it is possible to configure the NTC network with the battery pack thermistor between NTC and VCC, and a fixed resistor between NTC and ground. This configuration may be useful if it is desired to reset the charge timer (and the CHRGB output) when the battery pack is removed (so the fixed resistor pulls the NTC pin to ground) while VCC is present. Step 2: Verify acceptable thermistor self heating. In general, lower values of RT provide more noise immunity for the NTC voltage, but at the expense of bias current from the input adapter and power dissipation in the NTC network. The dissipation constant is the power rating of the thermistor resulting in a 1°C self heating error. The greatest self-heating occurs at low thermistor resistance (at high temperature). Since temperature sensing accuracy matters only at the charging temperature range thresholds, self heating is assessed only at the worst case high temperature threshold of +40°C. Cold Temperature Offset (CTO) The voltage applied to the CTO pin sets the NTC high voltage (normally the cold temperature threshold) for the NTC input. The default NTC high threshold (VTNTCC×VVCC) can be selected by connecting the CTO pin to ground. If it is desired to change this threshold, the voltage on the CTO pin can be set between 0.5×VVCC and 0.9×VVCC. For VVCC = 5V, the 40°C NTC network current INTC_HOT = VVCC/(R3 + RHOT) = 0.246mA. Power dissipation in the thermistor at this temperature, PHOT = RHOT × (INTC_HOT)2 = 0.38mW, for self heating of approximately 0.13°C. The actual high temperature threshold will thus be lower by 0.13°C. This self-heating error is usually acceptable. If it is not, then a thermistor with a greater RHOT must be chosen. This feature is especially useful if a single PCB design is needed to satisfy similar applications with different requirements. The temperature range for normal charging can be adjusted by adjusting resistor values on a divider network without changing the NTC thermistor, which is often enclosed in the battery pack. An example of a typical application is shown in Figure 2. Step 3: Determine the desired high (cold) threshold. Compute the NTC network resistor divider voltage, as a function of VVCC, at the cold temperature threshold. NTCCOLD = NTC/CTO Design Example The following example assumes the NTC network configuration of Figure 2, with a fixed resistor R3 connected between NTC and VCC, and a battery NTC thermistor RT connected between NTC and ground. The battery temperature range over which charging is permitted is specified to be 0°C through 40°C. The datasheet for the selected NTC thermistor indicates that RT = 5.839kΩ at 40°C, at RT = 26.49kΩ at 0°C, with a dissipation constant DC = 3mW. Designate RHOT = 5.839kΩ and RCOLD = 26.49kΩ. © 2007 Semtech Corp. VCC × RCOLD R3 + RCOLD = 0.6591 × VCC Step 4: Configure CTO. If NTCCOLD is sufficiently close to the default cold threshold (VTNTCC×VVCC), then simply connect CTO to ground, disabling the CTO function, to complete the design. But in this example it is not, so the voltage on CTO must be set to 0.6591×VVCC. The simple resistive voltage divider network of Figure 2 can be used to obtain the desired CTO voltage. 10 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Applications Information (Cont.) during CC charging whenever the current limit of the charging adapter is less than the SC804 FCI programmed current. In this case, the adapter voltage (the SC804 input voltage) will be pulled down to the battery voltage (the SC804 output voltage) plus the dropout voltage. VCTO = NTCCOLD = 0.6591 × VCC = VCC × RCT2 RCT1 + RCT2 Dropout voltage is the larger of two values: (1) the I-R component, which is the output current multiplied by the minimum VCC-to-VOUT path resistance (which is highly temperature dependent), and (2) a regulated minimum difference voltage, which is output voltage dependent but is independent of the output current. The regulated minimum dropout voltage results from the collapse of internal voltage references as VOUT pulls VCC down to near, or below, VCV, creating a reduced output regulation voltage approximately 200mV below VCC. Thus VCC cannot be pulled down below VOUT + 200mV. The dropout voltage will be larger than 200mV whenever the minimum path resistance multiplied by the output current exceeds 200mV, but it cannot be smaller than 200mV. or RCT1 1 0.6591 RCT2 = 0.6591 = 0.5172 The choice of RCT1 and RCT2 is somewhat arbitrary. The simplest approach is to pick one and compute the other. A good choice here is RCT1 = 115kΩ, and RCT2 = 221kΩ, as these standard 1% tolerance values produce the closest match to the desired voltage divider ratio. With these resistor nominal values, VCTO = VCC × RCT2 = 0.6577 × VCC RCT1 + RCT2 This greatest-of-two-limit dropout voltage behavior is evident in the dropout voltage typical performance plot. which is, nominally, only 0.2% below the target value of 0.6591×VVCC. The CTO network will present a load of only 15μA to a 5V charging adapter. The nominal impedance presented to the CTO pin is RCT1 || RCT2 = 75.6kΩ. Any impedance on the order of 100kΩ (or less) is acceptable. When operating in Adjust Mode (next section), the regulated minimum dropout voltage depends on the programmed VOUT regulation voltage, and dropout also varies with the actual output voltage during CC charging. See Figure 4 for an illustration of dropout voltage data. Remote Kelvin Sensing at the Battery Adjust Mode The BSEN pin provides the positive Kelvin sensing voltage feedback to the CV amplifier and should be connected as close to the battery + terminal as possible. Likewise, the RGND pin should be connected directly to the negative terminal of the battery. This allows the designer great flexibility in PCB layout and achieves greater accuracy by sensing the battery voltage directly at the battery terminals. When laying out the PCB, the designer should route the BSEN and RGND trace directly to the battery connection terminals, rather than just to the VOUT and GND pins on the device. The SC804 can be configured for an output voltage other than VCV using Adjust (ADJ) Mode. In Adjust Mode the output voltage is determined by an external resistor divider from VOUT to BSEN. When BSEN is connected in this fashion, VVOUT (during Constant Voltage (CV) charging) will be controlled such that the voltage at the BSEN pin (VBSEN) is the reference voltage VBSEN-ADJ. The output voltage can be set to any voltage desired by an appropriate choice of divider network resistors, within the following limits. When the SC804 is programmed for adjust mode, VVOUT is required to be 150mV less than VVCC, and VVOUT is required to be 400mV greater than VBSEN. Dropout Voltage VVOUT within 150mV of VBSEN guarantees normal mode operation. This implies that, for BSEN used as a Kelvin sense of battery voltage, the product of the fast charge Dropout voltage is the smallest achievable difference voltage between VCC and VOUT under a particular operating condition. Dropout voltage is encountered © 2007 Semtech Corp. 11 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Applications Information (Cont.) Charger VIN C1 2.2 μF 14 OV_FLT R3 RT NTC R1 R2 VCC CPB 13 OVP CHRGB 3 IPRGM RTIM 7 NTC CTO 4 ITERM BSEN 8 FLTB VOUT 6 GND VOUT 5 RGND AFC SC804 11 10 12 2 1 16 15 Red Green RCT1 RCT2 R5 R6 9 C2 2.2μF R4 ERROR Figure 2 - Application Circuit with AFC Disabled, and with NTC and CTO Resistor Networks Charger VIN C1 2.2 μF OV_FLT R3 RT NTC R1 R2 14 11 13 10 12 2 VCC CPB OVP CHRGB 3 IPRGM RTIM 7 NTC CTO 4 ITERM BSEN 8 FLTB VOUT 6 GND VOUT 5 RGND AFC SC804 Red Green 1 16 15 R11 R5 9 R6 C3 C2 2.2μF R4 R12 ERROR Figure 3a - Application Circuit for Adjust Mode Charger VIN C1 2.2 μF 14 OV_FLT R3 RT NTC R1 R2 VCC CPB 13 OVP CHRGB 3 IPRGM RTIM 7 NTC CTO 4 ITERM BSEN 8 FLTB VOUT 6 GND VOUT 5 RGND AFC SC804 11 10 12 2 1 16 15 9 Red Green R11 R4 C3 C2 2.2μF R5 R6 R12 ERROR Figure 3b - Application Circuit for Adjust Mode, with Adapter-only Voltage Sensing © 2007 Semtech Corp. 12 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Applications Information (Cont.) 0.8 Minimum dropout voltage, V current and the charge path resistance from VOUT to the Kelvin sense point should not exceed 150mV to ensure normal mode operation. The SC804 Adjust Mode schematic is shown in Figures 3A and 3B. Referring to these schematics, the equation for setting the output voltage is: VOUT = VBSEN-ADJ_Typ × R11 (1 + R12 ) The capacitor C3 across R8 in the feedback network introduces zero-pole frequency compensation for stability. Place the zero according to the following equation to ensure stability: R11 × C3 = 0.4 0.2 3.2 3.4 3.6 3.8 4 Output voltage, V 4.2 4.4 Figure 4 - Adjust Mode Minimum Dropout Voltage 1 2 × 100kHz The actual dropout voltage is the greater of the Minimum Dropout Voltage at various programmed VCV and instantaneous VOUT voltages (shown here, with several programmed VCV voltages indicated in the figure by ‘o’), and the IR drop due to the product of IOUT and RDS-ON (not shown here). Adjust mode operation is ensured for any IOUT current at programmed VCV voltages up to approximately 4.25V. NOTE: When using Adjust Mode to program a CV regulation voltage greater than VCV, care must be taken when CC charging with a charging adapter operating in current limit. Adapter current-limited operation occurs when the adapter current limit is less than the programmed SC804 fast charge current, such that the adapter voltage is pulled down to VVOUT plus the SC804 dropout voltage. A low adapter current limit multiplied by the low minimum path resistance of the main pass transistor and current sense resistor (as low as 290mΩ total at extremely low temperature) can result in a voltage drop from VCC to VOUT of less than 150mV if the Adjust Mode CV regulation voltage is programmed above VCV + 50mV. If VVCC - VVOUT < 150mV, Adjust Mode may not operate correctly. Adjust Mode will operate correctly whenever the programmed VOUT CV voltage is less than VCV + 50mV, regardless of the adapter current limit, because the regulated minimum dropout voltage is always greater than 150mV in this case. It will also operate correctly with an adapter current limit greater than 550 mA, regardless of the programmed output voltage, because the I-R dropout voltage will exceed 150mV at even the lowest specified operating temperature. Normal mode (that is, not Adjust Mode) has a regulated minimum dropout voltage of approximately 200mV, which is constant for any VVOUT, and so operates correctly for any adapter current limit. operation. When the device is in charge mode the output is current-limited to either the pre-charge current limit value or the fast charge current limit value depending on the voltage at the output. Max die temperature protection is also included. This feature allows the SC804 to operate with maximum power dissipation by disabling the output current when the die temperature reaches the maximum operating temperature. The result is that the SC804 will operate as a pulse charger in extreme power dissipation applications, delivering the maximum allowable output current while regulating the internal die temperature to a safe level. Indicator Flags There are four indicator outputs/LED drivers on the SC804: CPB (Charger Present), CHRGB (Charge Active), OVPB (Over Voltage Fault), and FLTB (Fault). These outputs are all active-low, open drain NMOS drivers capable of sinking up to 10mA. The following table defines each indicator’s output state. The CPB output can be used as a VCC-present indicator. Regardless of the state of NTC, the CPB output reflects the VCC voltage. When VVCC is between the UVLO and OVP thresholds the CPB output is low. If VVCC is outside these limits this output is high impedance. Over current and Max Temperature Protection Over current protection is inherent in all modes of © 2007 Semtech Corp. 0.6 13 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Applications Information (Cont.) FLAG ON OFF CPB UVLO < VCC < OVP Input out of range CHRGB IOUT > ITERM IOUT < ITERM OVPB VCC > OVP VCC < OVP FLTB VCC > OVP VCC UVLO NTC Temp Fault Pre-Charge Time-out (OT (Tj > 150°C) Normal Operation or NTC Disable The OVPB signal is an active-low output that signals when the input voltage exceeds the OVP threshold. When the voltage on VCC is less than the OVP threshold voltage this output is high impedance. The FLTB output is activated when the SC804 experiences a fault condition. This output can be used to notify the system controller of a fault condition when connected to an interrupt input, or it can be used like CPB and CHRGB to drive an indicator LED. The five fault modes signaled by FLTB are: input over-voltage, input under-voltage, NTC temperature out of range, max die temperature (OT), and pre-charge time-out. When any of these conditions occurs the FLTB output goes low; otherwise it remains high impedance. The CHRGB output indicates the charging status. When the output current is greater than ITERM, CHRGB is low. CHRGB is high impedance when IOUT is less than ITERM. The CHRGB output is latched during the charge cycle when the output current is less than ITERM. This latch is reset when the battery enters a recharge cycle, or if NTC or VCC are toggled. Capacitor Selection Low cost, low ESR ceramic capacitors such as the X5R and X7R dielectric material types are recommended for use with the SC804. The output capacitance range is 1μF to 4.7μF. The input capacitor is typically between 0.1μF to 1μF, but Charge Mode Timing Diagram larger values will not degrade performance. Charge Mode Timing Diagram VCC VOUT UVLO 2.8V Fast Charge Termination Current Soft Start IOUT Re- Charge Threshold Pre- Charge CV Mode CC Mode CPB CHRGB On TIMER FLTB Off On Off Off NTC On Off On On Hold On On Off Fault Figure 5 - Charge Mode Timing © 2007 Semtech Corp. 14 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT State Diagram Over-Voltage, Under-Voltage or Over-Temperature will force the SC804 into Shutdown Mode from any state. OVP > VCC > UVLO Shutdown Mode : VOUT & I OUT off, CHRGB High Z, CPB Low. En = Hi Yes Soft Start Vout CC = Constant Current CV = Constant Voltage CHRGB Low Timer Enabled? Yes Start Timer Start Pre- Charge Yes Soft Start CC Mode IOUT = IFAST V OUT > VTPreQ I OUT = IPREQ Time >T MAX/4 Yes VOUT = VCV Pre- Charge Timeout Fault FLTB goes low . Cleared by VBAT > VTPreQ or Re- cycle VCC Yes Start CV Mode IOUT <I TERM low temp> NTC Temp> high temp Yes CHRGB High Z Timer Enabled? Monitor Mode VOUT off Yes VOUT < VCV - VReQ © 2007 Semtech Corp. NTC out of Range Fault FLTB goes active low Timer is frozen Charge resumes when NTC Temperature is valid Yes Yes Time > TMAX Float Charge Mode VOUT = VCV 15 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Typical Charge Cycle Typical Charge Cycle Evaluation Board configured for internal timer, 1.5V on IPRGM = 810mA, 1.5V on ITERM = 300mA, VCC = 5.0V, Li-Ion battery capacity = 1000mAh. A 70mA battery load was applied after initial charge timeout, and removed during the recharge cycle prior to termination. (a) Constant Current (CC) Charging (Fast Charge); (b) Constant Voltage (CV) Charging; (c) Termination; (d) Float Charging; (e) Timer Expiration; (f) Slow Battery Discharge; (g) Recharge; (h) Termination. 4.5 Battery Voltage (b 4 (a) (f) (d) (h) (c) CHRGB Voltage 3.5 (g) Volts 3 2.5 2 (e) 1.5 ITERM Voltage 1 CHRGB Voltage 0.5 ITERM Voltage IPRGM Voltage 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 Time, hours © 2007 Semtech Corp. 16 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Typical Characteristics VOUT Vcv Line Regulation vs. Load, T = +25°C VOUT Vcv Line Regulation vs. Load, T = +25°C 4.220 4.220 Iout = 500mA VCC = 5.0V 4.215 4.215 4.210 4.210 VOUT (V) VOUT (V) Iout = 750mA Iout = 1000mA 4.205 VCC = 5.5V VCC = 6.0V 4.205 VCC = 6.5V Iout = 1500mA 4.200 4.195 5.00 4.200 5.20 5.40 5.60 5.80 6.00 6.20 4.195 500 6.40 VIN (V) 1000 1250 1500 IOUT (mA) VOUT Vcv Regulation vs. Temperature, VCC = 5.0V, Iout = 800mA 4.220 750 IOUT Line Regulation vs. Temperature, RPRGM = 1.87kΩ 808 T = +85°C 806 4.215 T = +25°C IOUT (mA) VOUT (V) 804 4.210 4.205 802 800 T = -40°C 798 796 4.200 794 4.195 -50 -25 0 25 50 75 792 4.25 100 4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 VCC (V) Ambient Temperature, °C IOUT vs. IPRGM Resistance, T = +25°C Precharge & Termination Current vs. ITERM Resistance 1600 400 350 1400 300 IOUT (mA) IOUT (mA) 1200 1000 250 200 150 800 100 600 50 400 0 0.3 0.5 0.7 0.9 1.1 0 Riprgm1/kΩ © 2007 Semtech Corp. 0.5 1 1.5 2 2.5 Riprgm1/kΩ 17 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Typical Characteristics (Cont.) Dropout Voltage vs. IOUT Rds-on vs. IOUT 0.620 0.900 TJ = +125°C 0.800 0.570 TJ = +125°C 0.700 0.520 Rds-on (Ω) Dropout (V) TJ = +85°C 0.600 TJ = +85°C 0.500 0.400 0.470 0.420 TJ = +25°C 0.370 0.300 TJ = +25°C 0.320 0.200 TJ = -40°C TJ = - 40°C 0.100 400 600 800 1000 1200 1400 0.270 400 1600 600 800 1000 1200 1400 1600 IOUT (mA) IOUT (mA) AFC Operation, RPRGM = 1.78kΩ 1200 AFC Pin Tied to VCC 1000 Iout (mA) 800 600 Actual AFC Response 400 200 Ideal AFC Response 0 0 0.5 1 1.5 2 VAFC, V © 2007 Semtech Corp. 18 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Evaluation EvaluationBoard BoardSchematic Schematic 1 RTIM 1 CHARGER- 1 CHARGER+ C1 1 R9 R10 1 <NM> JP6 3 1 BSEN 2 CTO 3 13 RTIM 12 CPB 11 1 SC804 1 10 CHRGB 1 1 2 R3 1 2 R13 1 2 FLTB 8 NTC GND 5 1 2 390 100k 1 2 2 1 2 390 2 1 R5 499 9 AFC RGND R12 <NM> 1 D4 R2 2 JP3 ITERM D3 37.4k R4 JP4 2 2 RGND 1 1 2 390 R14 1 0 R8 1 1 R7 2 1 <NM> 2 10k R16 1 3 1 1 NTC 2 GND D2 2 2 JP2 IPRGM 7 4 1 R6 1.87k GND 1 2 R15 OVPB 14 1 JP7 1 ITERM 2 390 U1 1 IPRGM 1 2 1 6 CTO JP5 15 16 C3 <NM> VCC 2 VOUT C2 2.2u 2 1 2 R11 0 1 VOUT 1 GND R1 JP1 1 1 1 VOUT D1 2 2 1 2 <NM> 1 2 2 2 1 1 2 2.2u POT_3296W-105 Evaluation Board Gerber Plots © 2007 Semtech Corp. 19 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Outline Drawing - MLPQ-16 DIM A D A A1 A2 b D D1 E E1 e L N aaa bbb B PIN 1 INDICATOR (LASER MARK) E A2 A aaa C A1 C DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX .040 .002 (.008) .012 .014 .157 .161 .085 .089 .157 .161 .085 .089 .026 BSC .012 .016 .020 16 .003 .004 .031 .000 .010 .153 .079 .153 .079 1.00 0.05 (0.20) 0.30 0.35 4.00 4.10 2.15 2.25 4.00 4.10 2.15 2.25 0.65 BSC 0.30 0.40 0.50 16 0.08 0.10 0.80 0.00 0.25 3.90 2.00 3.90 2.00 SEATING PLANE D1 e/2 LxN E/2 E1 2 1 N e D/2 bxN bbb C A B NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. Marking Information 804 yyww xxxxx xxxx yyww = Date Code Example (0552) xxxxx xxxx = Semtech Lot Number Example: (E9010 01-1) © 2007 Semtech Corp. 20 www.semtech.com SC804 PRELIMINARY POWER MANAGEMENT Land Pattern - MLPQ-16 K DIM 2x (C) H 2x G 2x Z Y X C G H K P X Y Z DIMENSIONS INCHES MILLIMETERS (.156) .122 .091 .091 .026 .016 .033 .189 (3.95) 3.10 2.30 2.30 0.65 0.40 0.85 4.80 P NOTES: 1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. Contact Information Semtech Corporation Power Management Products Division 200 Flynn Road, Camarillo, CA 93012 Phone: (805) 498-2111 FAX (805)498-3804 © 2007 Semtech Corp. 21 www.semtech.com