STMICROELECTRONICS 74VHC574TTR

74VHC574
OCTAL D-TYPE FLIP FLOP
WITH 3 STATE OUTPUTS NON INVERTING
■
■
■
■
■
■
■
■
■
■
■
HIGH SPEED:
fMAX = 180 MHz (TYP.) at VCC = 5V
LOW POWER DISSIPATION:
ICC = 4 µA (MAX.) at TA=25°C
HIGH NOISE IMMUNITY:
VNIH = VNIL = 28% VCC (MIN.)
POWER DOWN PROTECTION ON INPUTS
SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 8 mA (MIN)
BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL
OPERATING VOLTAGE RANGE:
VCC(OPR) = 2V to 5.5V
PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 574
IMPROVED LATCH-UP IMMUNITY
LOW NOISE: VOLP = 0.9V (MAX.)
DESCRIPTION
The 74VHC574 is an advanced high-speed
CMOS OCTAL D-TYPE FLIP FLOP with 3 STATE
OUTPUTS NON INVERTING fabricated with
sub-micron silicon gate and double-layer metal
wiring C2MOS technology.
These 8 bit D-Type flip-flop is controlled by a clock
input (CK) and an output enable input (OE).
On the positive transition of the clock, the Q
outputs will be set to the logic states that were
setup at the D inputs.
While the (OE) input is low, the 8 outputs will be in
a normal logic state (high or low logic level) and
SOP
TSSOP
Table 1: Order Codes
PACKAGE
T&R
SOP
TSSOP
74VHC574MTR
74VHC574TTR
while high level the outputs will be in a high
impedance state.
The Output control does not affect the internal
operation of flip flop; that is, the old data can be
retained or the new data can be entered even
while the outputs are off.
Power down protection is provided on all inputs
and 0 to 7V can be accepted on inputs with no
regard to the supply voltage. This device can be
used to interface 5V to 3V.
All inputs and outputs are equipped with
protection circuits against static discharge, giving
them 2KV ESD immunity and transient excess
voltage.
Figure 1: Pin Connection And IEC Logic Symbols
November 2004
Rev. 4
1/14
74VHC574
Figure 2: Input Equivalent Circuit
Table 2: Pin Description
PIN N°
SYMBOL
1
OE
2, 3, 4, 5, 6,
7, 8, 9
12, 13, 14,
15, 16, 17,
18, 19
11
D0 to D7
3-State Output Enable
Input (Active LOW)
Data Inputs
Q0 to Q7
3-State Outputs
10
20
CK
GND
VCC
NAME AND FUNCTION
Clock Input (LOW-to-HIGH
Edge Triggered)
Ground (0V)
Positive Supply Voltage
Table 3: Truth Table
INPUTS
OE
CK
D
Q
H
X
X
Z
L
X
NO CHANGE
L
L
L
L
H
H
X : Don’t Care
Z : High Impedance
Figure 3: Logic Diagram
This logic diagram has not be used to estimate propagation delays
2/14
OUTPUT
74VHC574
Table 4: Absolute Maximum Ratings
Symbol
VCC
Parameter
Supply Voltage
VI
DC Input Voltage
VO
DC Output Voltage
IIK
DC Input Diode Current
IOK
DC Output Diode Current
IO
DC Output Current
ICC or IGND DC VCC or Ground Current
Storage Temperature
Tstg
TL
Lead Temperature (10 sec)
Value
Unit
-0.5 to +7.0
V
-0.5 to +7.0
V
-0.5 to VCC + 0.5
- 20
V
mA
± 20
mA
± 25
mA
± 75
mA
-65 to +150
°C
300
°C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
Table 5: Recommended Operating Conditions
Symbol
VCC
Parameter
Supply Voltage
Value
Unit
2 to 5.5
V
VI
Input Voltage
0 to 5.5
V
VO
Output Voltage
0 to VCC
V
Top
Operating Temperature
-55 to 125
°C
0 to 100
0 to 20
ns/V
dt/dv
Input Rise and Fall Time (note 1) (VCC = 3.3 ± 0.3V)
(VCC = 5.0 ± 0.5V)
1) VIN from 30% to 70% of VCC
3/14
74VHC574
Table 6: DC Specifications
Test Condition
Symbol
VIH
VIL
VOH
VOL
IOZ
II
ICC
4/14
Parameter
High Level Input
Voltage
Low Level Input
Voltage
High Level Output
Voltage
Low Level Output
Voltage
High Impedance
Output Leakage
Current
Input Leakage
Current
Quiescent Supply
Current
Value
TA = 25°C
VCC
(V)
Min.
2.0
3.0 to
5.5
2.0
3.0 to
5.5
Typ.
Max.
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
1.5
1.5
1.5
0.7VCC
0.7VCC
0.7VCC
Max.
V
0.5
0.5
0.5
0.3VCC
0.3VCC
0.3VCC
2.0
IO=-50 µA
1.9
2.0
1.9
1.9
3.0
IO=-50 µA
2.9
3.0
2.9
2.9
4.5
IO=-50 µA
4.4
4.5
3.0
IO=-4 mA
2.58
3.94
4.4
4.4
2.48
2.4
Unit
V
V
4.5
IO=-8 mA
2.0
IO=50 µA
0.0
0.1
0.1
0.1
3.0
IO=50 µA
0.0
0.1
0.1
0.1
4.5
IO=50 µA
0.0
0.1
0.1
0.1
3.0
IO=4 mA
0.36
0.44
0.55
4.5
IO=8 mA
0.36
0.44
0.55
5.5
VI = VIH or VIL
VO = VCC or GND
±0.25
± 2.5
± 2.5
µA
0 to
5.5
VI = 5.5V or GND
± 0.1
±1
±1
µA
5.5
VI = VCC or GND
4
40
40
µA
3.8
3.7
V
74VHC574
Table 7: AC Electrical Characteristics (Input tr = tf = 3ns)
Test Condition
Symbol
Parameter
VCC
(V)
CL
(pF)
tPLH
tPHL
Propagation Delay
Time
CH to Q
3.3(*)
(*)
(**)
tPLZ
tPHZ
tw
ts
th
fMAX
Output Enable
Time
Output Disable
Time
Clock Pulse Width
HIGH or LOW
Setup Time D to CK
HIGH or LOW
Hold Time D to CK
HIGH or LOW
Maximum Clock
Frequency
Output to Output
Skew time (note 1)
-55 to 125°C
Min.
Max.
Min.
Max.
15
8.5
13.2
1.0
15.5
1.0
15.5
50
11.0
16.7
1.0
19.0
1.0
19.0
15
5.6
8.6
1.0
10.0
1.0
10.0
5.0(**)
50
7.1
10.6
1.0
12.0
1.0
12.0
3.3(*)
15
8.2
12.8
1.0
15.0
1.0
15.0
3.3(*)
50
10.7
16.3
1.0
18.5
1.0
18.5
5.0(**)
15
5.9
9.0
1.0
10.5
1.0
10.5
5.0(**)
50
7.4
11.0
1.0
12.5
1.0
12.5
(*)
50
11.0
15.0
1.0
17.0
1.0
17.0
(*)
50
7.1
10.1
1.0
11.5
1.0
11.5
3.3
3.3
3.3
Min.
-40 to 85°C
Max.
3.3(*)
5.0
5.0
5.0
5.0(**)
5.0
5.0
5.0
3.3(*)
3.5
3.5
3.5
5.0(**)
3.5
3.5
3.5
3.3(*)
1.5
1.5
1.5
5.0(**)
1.5
1.5
1.5
3.3(*)
15
80
125
65
65
(*)
50
50
75
45
45
(**)
15
130
180
110
110
5.0(**)
50
85
115
75
75
3.3(*)
50
1.5
1.5
1.5
5.0(**)
50
1.0
1.0
1.0
3.3
5.0
tOSLH
tOSHL
TA = 25°C
Typ.
5.0
tPZL
tPZH
Value
Unit
ns
ns
ns
ns
ns
ns
MHz
ns
(*) Voltage range is 3.3V ± 0.3V
(**) Voltage range is 5.0V ± 0.5V
Note 1: Parameter guaranteed by design. tsoLH = |tpLHm - tpLHn|, tsoHL = |tpHLm - tpHLn|
Table 8: Capacitive Characteristics
Test Condition
Symbol
Parameter
Value
TA = 25°C
Min.
CIN
Input Capacitance
COUT
Output
Capacitance
Power Dissipation
Capacitance
(note 1)
CPD
Typ.
Max.
7
10
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
10
Unit
Max.
10
pF
9
pF
28
pF
1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/8 (per
Flip-Flop)
5/14
74VHC574
Table 9: Dynamic Switching Characteristics
Test Condition
Symbol
VOLP
VOLV
VIHD
VILD
Parameter
Dynamic Low
Voltage Quiet
Output (note 1, 2)
Dynamic High
Voltage Input
(note 1, 3)
Dynamic Low
Voltage Input
(note 1, 3)
TA = 25°C
VCC
(V)
Min.
5.0
5.0
Value
-0.9
CL = 50 pF
5.0
Typ.
Max.
0.6
0.9
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
Unit
Max.
V
-0.6
3.5
V
1.5
V
1) Worst case package.
2) Max number of outputs defined as (n). Data inputs are driven 0V to 5.0V, (n-1) outputs switching and one output at GND.
3) Max number of data inputs (n) switching. (n-1) switching 0V to 5.0V. Inputs under test switching: 5.0V to threshold (VILD ), 0V to threshold
(VIHD), f=1MHz.
Figure 4: Test Circuit
TEST
tPLH, tPHL
SWITCH
Open
tPZL, tPLZ
VCC
tPZH, tPHZ
GND
CL =15/50pF or equivalent (includes jig and probe capacitance)
RL = R1 = 1KΩ or equivalent
RT = ZOUT of pulse generator (typically 50Ω)
6/14
74VHC574
Figure 5: Waveform - Propagation Delays, Setup And Hold Times (f=1MHz; 50% duty cycle)
Figure 6: Waveform 2: Output Enable And Disable Times (f=1MHz; 50% duty cycle)
7/14
74VHC574
Figure 7: Waveform - Pulse Width (f=1MHz; 50% duty cycle)
8/14
74VHC574
SO-20 MECHANICAL DATA
DIM.
mm.
MIN.
TYP
inch
MAX.
MIN.
TYP.
MAX.
A
2.35
2.65
0.093
0.104
A1
0.1
0.30
0.004
0.012
B
0.33
0.51
0.013
0.020
C
0.23
0.32
0.009
0.013
D
12.60
13.00
0.496
0.512
E
7.4
7.6
0.291
0.299
e
1.27
0.050
H
10.00
10.65
0.394
0.419
h
0.25
0.75
0.010
0.030
L
0.4
1.27
0.016
0.050
k
0°
8°
0°
8°
ddd
0.100
0.004
0016022D
9/14
74VHC574
TSSOP20 MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
MAX.
A
MIN.
TYP.
MAX.
1.2
A1
0.05
A2
0.8
b
0.047
0.15
0.002
0.004
0.006
1.05
0.031
0.039
0.041
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.0079
D
6.4
6.5
6.6
0.252
0.256
0.260
E
6.2
6.4
6.6
0.244
0.252
0.260
E1
4.3
4.4
4.48
0.169
0.173
0.176
1
e
0.65 BSC
K
0˚
L
0.45
A
0.0256 BSC
0.60
8˚
0˚
0.75
0.018
8˚
0.024
0.030
A2
A1
b
K
e
L
E
c
D
E1
PIN 1 IDENTIFICATION
1
0087225C
10/14
74VHC574
Tape & Reel SO-20 MECHANICAL DATA
mm.
inch
DIM.
MIN.
A
TYP
MAX.
MIN.
330
MAX.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
13.2
TYP.
0.504
30.4
0.519
1.197
Ao
10.8
11
0.425
0.433
Bo
13.2
13.4
0.520
0.528
Ko
3.1
3.3
0.122
0.130
Po
3.9
4.1
0.153
0.161
P
11.9
12.1
0.468
0.476
11/14
74VHC574
Tape & Reel TSSOP20 MECHANICAL DATA
mm.
inch
DIM.
MIN.
A
MAX.
MIN.
330
13.2
TYP.
MAX.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
12/14
TYP
0.504
22.4
0.519
0.882
Ao
6.8
7
0.268
0.276
Bo
6.9
7.1
0.272
0.280
Ko
1.7
1.9
0.067
0.075
Po
3.9
4.1
0.153
0.161
P
11.9
12.1
0.468
0.476
74VHC574
Table 10: Revision History
Date
Revision
12-Nov-2004
4
Description of Changes
Order Codes Revision - pag. 1.
13/14
74VHC574
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
All other names are the property of their respective owners
© 2004 STMicroelectronics - All Rights Reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
14/14