STMICROELECTRONICS M41ST87WMX6TR

M41ST87Y
M41ST87W
5.0 V and 3.3/3.0 V secure serial RTC and NVRAM supervisor
with tamper detection and 128 bytes of clearable NVRAM
Features
■
5.0, 3.3, or 3.0 V operation
■
400 kHz I2C bus
■
NVRAM supervisor to non-volatize external
LPSRAM
■
2.5 to 5.5 V oscillator operating voltage
■
Automatic switchover and deselect circuitry
■
Choice of power-fail deselect voltages
– M41ST87Y:
THS = 1: VPFD≈ 4.63 V; VCC = 4.75 to 5.5 V
THS = 0: VPFD≈ 4.37 V; VCC = 4.5 to 5.5 V
– M41ST87W:
THS = 1: VPFD ≈ 2.9 V; VCC = 3.0 to 3.6 V
THS = 0: VPFD ≈ 2.63 V; VCC = 2.7 to 3.6 V
■
Two independent power-fail comparators
(1.25 V reference)
■
Counters for tenths/hundredths of seconds,
seconds, minutes, hours, day, date, month,
year, and century
■
128 bytes of clearable, general purpose
NVRAM
■
Programmable alarm and interrupt function
(valid even during battery backup mode)
■
Programmable watchdog timer
■
Unique electronic serial number (8-byte)
■
32 kHz frequency output available upon poweron
■
Microprocessor power-on reset output
■
Battery low flag
■
Ultra-low battery supply current of 500 nA (typ)
September 2008
Embedded crystal
28-pin, (300 mil)
SOX28 (MX)
Security features
■
Tamper indication circuits with timestamp and
RAM clear
■
LPSRAM clear function (TPCLR)
■
Packaging includes a 28-lead, embedded
crystal SOIC
■
Oscillator stop detection
Rev 7
1/48
www.st.com
1
Contents
M41ST87Y, M41ST87W
Contents
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1
2
Security features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.1
2-wire bus characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.1.1
Bus not busy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.1.2
Start data transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.1.3
Stop data transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.1.4
Data valid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.1.5
Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2
READ mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.3
WRITE mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.4
Data retention mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.5
Tamper detection circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.6
Tamper register bits (tamper 1 and tamper 2) . . . . . . . . . . . . . . . . . . . . . 17
2.6.1
Tamper enable bits (TEB1 and TEB2) . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.6.2
Tamper bits (TB1 and TB2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.6.3
Tamper interrupt enable bits (TIE1 and TIE2) . . . . . . . . . . . . . . . . . . . . 18
2.6.4
Tamper connect mode bit (TCM1 and TCM2) . . . . . . . . . . . . . . . . . . . . 18
2.6.5
Tamper polarity mode bits (TPM1 and TPM2) . . . . . . . . . . . . . . . . . . . . 18
2.6.6
Tamper detect sampling (TDS1 and TDS2) . . . . . . . . . . . . . . . . . . . . . . 21
2.6.7
Tamper current high/tamper current low (TCHI/TCLO1 and
TCHI/TCLO2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3
2.6.8
RAM clear (CLR1 and CLR2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.6.9
RAM clear external (CLR1EXT and CLR2EXT) . . . . . . . . . . . . . . . . . . . . 21
2.7
Tamper detection operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2.8
Sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2.9
Internal tamper pull-up/down current . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2.10
Avoiding inadvertent tampers (normally closed configuration) . . . . . . . . . 26
2.11
Tamper event time-stamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Clock operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.0.1
2/48
Power-down time-stamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
M41ST87Y, M41ST87W
Contents
3.1
TIMEKEEPER® registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.2
Calibrating the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.3
Setting alarm clock registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.4
Watchdog timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.5
Square wave output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.6
Full-time 32 kHz square wave output . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.7
Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.8
Reset inputs (RSTIN1 & RSTIN2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.9
Power-fail comparators (1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.10
Power-fail outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.11
Century bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.12
Output driver pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.13
Battery low warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.14
trec bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.15
Electronic serial number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.16
Oscillator stop detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.17
Initial power-on defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
5
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
6
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
7
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
8
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3/48
List of tables
M41ST87Y, M41ST87W
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
4/48
Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Tamper detection truth table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Tamper detection current (normally closed - TCMX = '0') . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Tamper detect timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Calculated cut-off frequency for typical capacitance and resistance values. . . . . . . . . . . . 26
TIMEKEEPER® register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Alarm repeat modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Square wave output frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Reset AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Century bits examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
trec definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Default values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
DC and AC measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
DC characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Power down/up AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
SOX28 – 28-lead plastic small outline, 300 mils, embedded crystal, mechanical data . . . 45
Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
M41ST87Y, M41ST87W
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
28-pin, 300 mil SOIC (MX) connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hardware hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Serial bus data transfer sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Acknowledgement sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Bus timing requirements sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Slave address location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
READ mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Alternate READ mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
WRITE mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
WRITE cycle timing: RTC & external SRAM control signals. . . . . . . . . . . . . . . . . . . . . . . . 16
Tamper detect connection options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Tamper detect output options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Basic tamper detect options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Tamper detect sampling options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Tamper current options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Tamper output timing (with CLR1EXT or CLR2EXT = '1'). . . . . . . . . . . . . . . . . . . . . . . . . . . 23
RAM clear hardware hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Low-pass filter implementation for noise immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Crystal accuracy across temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Calibration waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Alarm interrupt reset waveform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Backup mode alarm waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
RSTIN1 & RSTIN2 timing waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
AC testing input/output waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Power down/up mode AC waveforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
SOX28 – 28-lead plastic small outline, 300 mils, embedded crystal outline. . . . . . . . . . . . 45
5/48
Description
1
M41ST87Y, M41ST87W
Description
The M41ST87Y/W serial TIMEKEEPER®/controller SRAM is a low power 1280-bit, static
CMOS SRAM organized as 160 bytes by 8 bits. A built-in 32.768 kHz oscillator (internal
crystal-controlled) and 8 bytes of the SRAM (see Table 7 ) are used for the clock/calendar
function and are configured in binary coded decimal (BCD) format.
An additional 11 bytes of RAM provide calibration, status/control of alarm, watchdog,
tamper, and square wave functions. 8 bytes of ROM and finally 128 bytes of user RAM are
also provided. Addresses and data are transferred serially via a two line, bidirectional I2C
interface. The built-in address register is incremented automatically after each WRITE or
READ data byte. The M41ST87Y/W has a built-in power sense circuit which detects power
failures and automatically switches to the battery supply when a power failure occurs. The
energy needed to sustain the SRAM and clock operations can be supplied by a small lithium
button-cell supply when a power failure occurs.
Functions available to the user include a non-volatile, time-of-day clock/calendar, alarm
interrupts, tamper detection, watchdog timer, and programmable square wave output. Other
features include a power-on reset as well as two additional debounced inputs (RSTIN1 and
RSTIN2) which can also generate an output reset (RST). The eight clock address locations
contain the century, year, month, date, day, hour, minute, second and tenths/hundredths of a
second in 24 hour BCD format. Corrections for 28, 29 (leap year), 30 and 31 day months are
made automatically.
1.1
Security features
Two fully independent tamper detection Inputs allow monitoring of multiple locations within
the system. Programmable bits provide both, “normally open” and “normally closed” switch
monitoring. Time stamping of the tamper event is automatically provided. There is also an
option allowing data stored in either internal memory (128 bytes), and/or external memory to
be cleared, protecting sensitive information in the event tampering occurs. By embedding
the 32 kHz crystal in the package, the clock is completely isolated from external tampering.
An oscillator fail bit (OF) is also provided to ensure correct operation of the oscillator.
The M41ST87Y/W is supplied in a 28-pin, 300 mil SOIC package (MX) which includes an
embedded 32 kHz crystal.
The SOIC package is shipped in plastic anti-static tubes or in tape & reel form.
The 300 mil, embedded crystal SOIC requires only a user-supplied battery to provide nonvolatile operation.
6/48
M41ST87Y, M41ST87W
Figure 1.
Description
Logic diagram
VCC
VBAT
SCL
ECON
SDA
RST(1)
EX
IRQ/OUT(1)
RSTIN1
RSTIN2
WDI
SQW/FT(2)
M41ST87Y
M41ST87W
PFO1(2)
PFO2(2)
PFI1
VOUT
PFI2
(1)
F32k
TP1IN
TPCLR
TP2IN
VSS
AI07023
1. Open drain output
2. Programmable output (open drain or full-CMOS)
Figure 2.
28-pin, 300 mil SOIC (MX) connections
NF
NF
NF
NF
NC
NC
PFO2
SQW/FT
WDI
RSTIN1
RSTIN2
PFO1
PFI2
VSS
28
1
2
27
3
26
4
25
5
24
6
23
7
22
M41ST87Y
8 M41ST87W 21
9
20
10
19
11
18
12
17
13
16
14
15
VCC
EX
IRQ/OUT
VOUT
TP2IN
PFI1
SCL
F32k
TP1IN
RST
TPCLR
SDA
ECON
VBAT
AI07025b
Note:
No function (NF) and no connect (NC) pins should be tied to VSS. Pins 1, 2, 3, and 4 are
internally shorted together.
7/48
Description
M41ST87Y, M41ST87W
Table 1.
Signal names
ECON
Conditioned chip enable output
EX
External chip enable
(1)
IRQ/OUT
Interrupt/out output (open drain)
PFI1
Power fail input 1
PFI2
Power fail input 2
PFO1(2)
Power fail output 1
PFO2(2)
Power fail output 2
RST(1)
Reset output (open drain)
RSTIN1
Reset 1 input
RSTIN2
Reset 2 input
SCL
Serial clock input
SDA
Serial data input/output
SQW/FT(2)
Square wave output/frequency test
WDI
Watchdog input
VCC
Supply voltage
VOUT
Voltage output
VSS
Ground
F32k(1)
32 kHz square wave output (open drain)
TP1IN
Tamper pin 1 input
TP2IN
Tamper pin 2 input
TPCLR
Tamper pin RAM clear
VBAT
Positive battery pin input
NF(3)
No function
NC(3)
No connect
1. Open drain output
2. Programmable output (open drain or full-CMOS)
3. Should be connected to VSS.
8/48
M41ST87Y, M41ST87W
Figure 3.
Description
Block diagram
REAL TIME CLOCK
CALENDAR
128 BYTES
USER RAM
SDA
I2C
INTERFACE
8 BYTES ROM
OFIE
RTC w/ALARM
& CALIBRATION
SCL
Crystal
VOUT
WATCHDOG
32KHz
OSCILLATOR
AFE
WDS
SQUARE WAVE
TIEX
CLRX
2
TPXIN
TAMPER
WDI
VCC
(1)
IRQ/OUT
CLRXEXT
SQW/FT(2)
TPCLR
VOUT
VBAT
F32k(1)
VSS
VBL
COMPARE
VSO
COMPARE
VPFD
COMPARE
BL
POR
RST
RSTIN1
(1)
RSTIN2
ECON
EX
PFI1
COMPARE
PFO1(2)
COMPARE
PFO2(2)
1.25V
(Internal)
PFI2
1.25V
(Internal)
AI07026
1. Open drain output.
2. Programmable output (open drain or full-CMOS); if open drain option is selected and if pulled-up to supply other than VCC,
this supply must be equal to, or less than 3.0 V when VCC = 0 V (during battery backup mode).
9/48
Description
Figure 4.
M41ST87Y, M41ST87W
Hardware hookup
M41ST87Y/W
Inhibit
Unregulated
Voltage
VIN
VCC
5V
Regulator
VCC
TP1IN
TP2IN
Inhibit
VCC
3.3V
Regulator
VIN
For monitoring
of additional
voltage sources
R1
Pushbutton
Reset
R3
VOUT
VCC
ECON
E
EX
Low-Power
SRAM
SCL
WDI
SDA
RSTIN1
RST
RSTIN2
SQW/FT
PFO1
PFI1
R2
TPCLR
To RST
To LED Display
To NMI
PFO2
PFI2
VSS
R4
VBAT
IRQ/OUT
F32k
To INT
To 32kHz
AI07027
10/48
M41ST87Y, M41ST87W
2
Operating modes
Operating modes
The M41ST87Y/W clock operates as a slave device on the serial bus. Access is obtained by
implementing a start condition followed by the correct slave address (D0h). The 160 bytes
contained in the device can then be accessed sequentially in the following order:
00h.
Tenths/hundredths of a second register
01h.
Seconds register
02h.
Minutes register
03h.
Century/hours register
04h.
Day register
05h.
Date register
06h.
Month register
07h.
Year register
08h.
Control register
09h.
Watchdog register
0Ah-0Eh. Alarm registers
0Fh.
Flag register
10h-12h.
Reserved
13h.
Square wave
14h.
Tamper register 1
15h.
Tamper register 2
16h-1Dh.
Serial number (8 bytes)
1Eh-1Fh.
Reserved (2 bytes)
20h-9Fh.
User RAM (128 bytes)
The M41ST87Y/W clock continually monitors VCC for an out-of-tolerance condition. Should
VCC fall below VPFD, the device terminates an access in progress and resets the device
address counter. Inputs to the device will not be recognized at this time to prevent erroneous
data from being written to the device from a an out-of-tolerance system. When VCC falls
below VSO, the device automatically switches over to the battery and powers down into an
ultra low current mode of operation to conserve battery life. As system power returns and
VCC rises above VSO, the battery is disconnected, and the power supply is switched to
external VCC.
Write protection continues until VCC reaches VPFD (min) plus trec (min).
For more information on battery storage life refer to application note AN1012.
11/48
Operating modes
2.1
M41ST87Y, M41ST87W
2-wire bus characteristics
The bus is intended for communication between different ICs. It consists of two lines: a
bidirectional data signal (SDA) and a clock signal (SCL). Both the SDA and SCL lines must
be connected to a positive supply voltage via a pull-up resistor.
The following protocol has been defined:
●
Data transfer may be initiated only when the bus is not busy.
●
During data transfer, the data line must remain stable whenever the clock line is high.
●
Changes in the data line, while the clock line is high, will be interpreted as control
signals.
Accordingly, the following bus conditions have been defined:
2.1.1
Bus not busy
Both data and clock lines remain high.
2.1.2
Start data transfer
A change in the state of the data line, from high to low, while the clock is high, defines the
START condition.
2.1.3
Stop data transfer
A change in the state of the data line, from low to high, while the clock is high, defines the
STOP condition.
2.1.4
Data valid
The state of the data line represents valid data when after a start condition, the data line is
stable for the duration of the high period of the clock signal. The data on the line may be
changed during the Low period of the clock signal. There is one clock pulse per bit of data.
Each data transfer is initiated with a start condition and terminated with a stop condition.
The number of data bytes transferred between the start and stop conditions is not limited.
The information is transmitted byte-wide and each receiver acknowledges with a ninth bit.
By definition a device that gives out a message is called “transmitter,” the receiving device
that gets the message is called “receiver.” The device that controls the message is called
“master.” The devices that are controlled by the master are called “slaves.”
2.1.5
Acknowledge
Each byte of eight bits is followed by one acknowledge bit. This acknowledge bit is a low
level put on the bus by the receiver whereas the master generates an extra acknowledge
related clock pulse. A slave receiver which is addressed is obliged to generate an
acknowledge after the reception of each byte that has been clocked out of the slave
transmitter.
The device that acknowledges has to pull down the SDA line during the acknowledge clock
pulse in such a way that the SDA line is a stable low during the high period of the
acknowledge related clock pulse. Of course, setup and hold times must be taken into
account. A master receiver must signal an end of data to the slave transmitter by not
generating an acknowledge on the last byte that has been clocked out of the slave. In this
12/48
M41ST87Y, M41ST87W
Operating modes
case the transmitter must leave the data line high to enable the master to generate the
STOP condition.
Figure 5.
Serial bus data transfer sequence
DATA LINE
STABLE
DATA VALID
CLOCK
DATA
START
CONDITION
CHANGE OF
DATA ALLOWED
STOP
CONDITION
AI00587
Figure 6.
Acknowledgement sequence
CLOCK PULSE FOR
ACKNOWLEDGEMENT
START
SCL FROM
MASTER
1
DATA OUTPUT
BY TRANSMITTER
2
8
MSB
9
LSB
DATA OUTPUT
BY RECEIVER
AI00601
Figure 7.
Bus timing requirements sequence
SDA
tBUF
tHD:STA
tHD:STA
tR
tF
SCL
tHIGH
P
S
tLOW
tSU:DAT
tHD:DAT
tSU:STA
SR
tSU:STO
P
AI00589
13/48
Operating modes
Table 2.
M41ST87Y, M41ST87W
AC characteristics
Parameter(1)
Symbol
fSCL
SCL clock frequency
tBUF
Time the bus must be free before a new transmission can start
tEXPD
EX to ECON propagation delay
tF
tHD:DAT(2)
Min
Max
Unit
0
400
kHz
1.3
M41ST87Y
10
M41ST87W
SDA and SCL fall time
ns
15
ns
300
ns
0
µs
START condition hold time
(after this period the first clock pulse is generated)
600
ns
tHIGH
Clock high period
600
ns
tLOW
Clock low period
1.3
tHD:STA
tR
Data hold time
µs
SDA and SCL rise time
µs
300
ns
tSU:DAT
Data setup time
100
ns
tSU:STA
START condition setup time
(only relevant for a repeated start condition)
600
ns
tSU:STO
STOP condition setup time
600
ns
1. Valid for ambient operating temperature: TA = –40 to 85°C; VCC = 4.5 to 5.5 V or 2.7 to 3.6 V (except where noted).
2. Transmitter must internally provide a hold time to bridge the undefined region (300 ns max) of the falling edge of SCL.
2.2
READ mode
In this mode the master reads the M41ST87Y/W slave after setting the slave address (see
Figure 8 on page 15). Following the WRITE mode control bit (R/W=0) and the acknowledge
bit, the word address 'An' is written to the on-chip address pointer. Next the START condition
and slave address are repeated followed by the READ mode control bit (R/W=1). At this
point the master transmitter becomes the master receiver.
The data byte which was addressed will be transmitted and the master receiver will send an
acknowledge bit to the slave transmitter. The address pointer is only incremented on
reception of an acknowledge clock. The M41ST87Y/W slave transmitter will now place the
data byte at address An+1 on the bus, the master receiver reads and acknowledges the new
byte and the address pointer is incremented to An+2.
This cycle of reading consecutive addresses will continue until the master receiver sends a
STOP condition to the slave transmitter (see Figure 9 on page 15).
The system-to-user transfer of clock data will be halted whenever the address being read is
a clock address (00h to 07h). The update will resume either due to a Stop Condition or when
the pointer increments to a non-clock or RAM address.
Note:
This is true both in READ mode and WRITE mode.
An alternate READ mode may also be implemented whereby the master reads the
M41ST87Y/W slave without first writing to the (volatile) address pointer. The first address
that is read is the last one stored in the pointer (see Figure 10 on page 15).
14/48
M41ST87Y, M41ST87W
Figure 8.
Operating modes
Slave address location
R/W
SLAVE ADDRESS
1
A
LSB
MSB
START
1
0
1
0
0
0
AI00602
R/W
SLAVE
ADDRESS
DATA n+1
ACK
DATA n
ACK
BUS ACTIVITY:
S
ACK
WORD
ADDRESS (An)
ACK
S
R/W
SDA LINE
ACK
BUS ACTIVITY:
MASTER
START
READ mode sequence
START
Figure 9.
STOP
SLAVE
ADDRESS
DATA n+X
P
NO ACK
AI00899
STOP
R/W
SLAVE
ADDRESS
DATA n+X
P
NO ACK
BUS ACTIVITY:
DATA n+1
ACK
DATA n
ACK
S
ACK
SDA LINE
ACK
BUS ACTIVITY:
MASTER
START
Figure 10. Alternate READ mode sequence
AI00895
15/48
Operating modes
2.3
M41ST87Y, M41ST87W
WRITE mode
In this mode the master transmitter transmits to the M41ST87Y/W slave receiver. Bus
protocol is shown in Figure 11. Following the START condition and slave address, a logic '0'
(R/W=0) is placed on the bus and indicates to the addressed device that word address An
will follow and is to be written to the on-chip address pointer. The data word to be written to
the memory is strobed in next and the internal address pointer is incremented to the next
memory location within the RAM on the reception of an acknowledge clock. The
M41ST87Y/W slave receiver will send an acknowledge clock to the master transmitter after
it has received the slave address (see Figure 8 on page 15) and again after it has received
the word address and each data byte.
STOP
SLAVE
ADDRESS
DATA n+X
P
ACK
DATA n+1
ACK
BUS ACTIVITY:
DATA n
ACK
WORD
ADDRESS (An)
ACK
S
R/W
SDA LINE
ACK
BUS ACTIVITY:
MASTER
START
Figure 11. WRITE mode sequence
AI00591
Figure 12. WRITE cycle timing: RTC & external SRAM control signals
EX
tEXPD
tEXPD
ECON
AI03663
2.4
Data retention mode
With valid VCC applied, the M41ST87Y/W can be accessed as described above with READ
or WRITE Cycles. Should the supply voltage decay, the M41ST87Y/W will automatically
deselect, write protecting itself (and any external SRAM) when VCC falls between VPFD
(max) and VPFD (min) (see Figure 27 on page 43, Table 18 on page 44). This is
accomplished by internally inhibiting access to the clock registers. At this time, the Reset pin
(RST) is driven active and will remain active until VCC returns to nominal levels. External
RAM access is inhibited in a similar manner by forcing ECON to a high level. This level is
within 0.2 volts of the VBAT. ECON will remain at this level as long as VCC remains at an outof-tolerance condition. When VCC falls below the battery backup switchover voltage (VSO),
16/48
M41ST87Y, M41ST87W
Operating modes
power input is switched from the VCC pin to the battery, and the clock registers and external
SRAM are maintained from the attached battery supply.
All outputs become high impedance. The VOUT pin is capable of supplying 100µA (for
M41ST87W) or 150µA (for M41ST87Y) of current to the attached memory with less than 0.3
volts drop under this condition. On power up, when VCC returns to a nominal value, write
protection continues for trec by inhibiting ECON. The RST signal also remains active during
this time (see Figure 27 on page 43).
Note:
Most low power SRAMs on the market today can be used with the M41ST87Y/W RTC
SUPERVISOR. There are, however some criteria which should be used in making the final
choice of an SRAM to use. The SRAM must be designed in a way where the chip enable
input disables all other inputs to the SRAM. This allows inputs to the M41ST87Y/W and
SRAMs to be “Don’t Care” once VCC falls below VPFD(min). The SRAM should also
guarantee data retention down to VCC = 2.0 volts. The chip enable access time must be
sufficient to meet the system needs with the chip enable output propagation delays
included. If the SRAM includes a second chip enable pin (E2), this pin should be tied to
VOUT.
If data retention lifetime is a critical parameter for the system, it is important to review the
data retention current specifications for the particular SRAMs being evaluated. Most SRAMs
specify a data retention current at 3.0 volts. Manufacturers generally specify a typical
condition for room temperature along with a worst case condition (generally at elevated
temperatures). The system level requirements will determine the choice of which value to
use. The data retention current value of the SRAMs can then be added to the IBAT value of
the M41ST87Y/W to determine the total current requirements for data retention. The
available battery capacity for the battery of your choice can then be divided by this current to
determine the amount of data retention available.
For a further more detailed review of lifetime calculations, please see Application Note
AN1012.
2.5
Tamper detection circuit
The M41ST87Y/W provides two independent input pins, the tamper pin 1 input (TP1IN) and
tamper pin 2 input (TP2IN), which can be used to monitor two separate signals which can
result in the associated setting of the tamper bits (TB1 and/or TB2, in flag register 0Fh) if the
tamper enable bits (TEB1 and/or TEB2) are enabled, for the respective tamper 1 or tamper
2. The TP1IN pin or TP2IN pin may be set to indicate a tamper event has occurred by either
1) closing a switch to ground or VOUT (normally open), or by 2) opening a switch that was
previously closed to ground or VOUT (normally closed), depending on the state of the TCMX
bits and the TPMX bits in the tamper register (14h and/or 15h).
2.6
Tamper register bits (tamper 1 and tamper 2)
2.6.1
Tamper enable bits (TEB1 and TEB2)
When set to a logic '1,' this bit will enable the tamper detection circuit. This bit must be set to
'0' in order to clear the associated tamper bits (TBX, in 0Fh).
Note:
TEBX should be reset whenever the tamper detect condition is modified.
17/48
Operating modes
2.6.2
M41ST87Y, M41ST87W
Tamper bits (TB1 and TB2)
If the TEBX bit is set, and a tamper condition occurs, the TBX bit will be set to '1.' This bit is
“Read-only” and is reset only by setting the TEBX bit to '0.' These bits are located in the flags
register 0Fh.
2.6.3
Tamper interrupt enable bits (TIE1 and TIE2)
If this bit is set to a logic '1,' the IRQ/OUT pin will be activated when a tamper event occurs.
This function is also valid in battery backup if the ABE bit (alarm in battery backup) is also
set to '1' (see Figure 14 on page 20).
Note:
In order to avoid an inadvertent activation of the IRQ/OUT pin due to a prior tamper event,
the flag register (0Fh) should be read prior to resetting the TEBX bit.
2.6.4
Tamper connect mode bit (TCM1 and TCM2)
This bit indicates whether the position of the external switch selected by the user is in the
normally open (TCMX = '1') or normally closed (TCMX = '0') position (see Figure 13 on
page 19 and Figure 15 on page 20).
2.6.5
Tamper polarity mode bits (TPM1 and TPM2)
The state of this bit indicates whether the tamper pin input will be taken high (to VOUT if
TPMX = '1') or low (to VSS if TPMX = '0') during a tamper event (see Figure 13 on page 19
and Figure 15 on page 20).
18/48
M41ST87Y, M41ST87W
Operating modes
Figure 13. Tamper detect connection options
TAMPER LO
(TPMX = 0)
TAMPER HI
(TPMX = 1)
I.
II.
(1)
VOUT
NORMALLY
OPEN
(TCMX = 1)
TPIN
TPIN
III.
IV.
VOUT(2)
VCC
TPIN
NORMALLY
CLOSED
(TCMX = 0)
VOUT (Int)
(3)
TCHI/TCLO = 1
TCHI/TCLO = 0
1MΩ
TCHI/TCLO = 1
10MΩ
TCHI/TCLO = 0
10MΩ
1MΩ
AI07075
Note:
These options are connected to those in Table 3.
1. If the CLRXEXT bit is set, a second tamper to VOUT (TPM2 = '1') during tCLR will not be detected.
2. If the CLRXEXT bit is set, a second tamper to VOUT (TPM2 = '1') will trigger automatically.
3. Optional external resistor to VCC allows the user to bypass sampling when power is “on.”
Table 3.
Option
Tamper detection truth table
Mode
I
Normally open/tamper to GND(1)
(1)
TCMX
TPMX
1
0
II
Normally open/tamper to VOUT
1
1
III
Normally closed/tamper to GND
0
0
IV
Normally closed/tamper to VOUT
0
1
1. No battery current drawn during battery backup.
19/48
Operating modes
M41ST87Y, M41ST87W
Figure 14. Tamper detect output options
User
Configuration
TIE1
IRQ - Interrupt the
processor on tamper
CLR1EXT
TPCLR - Clear external
RAM on tamper
TP1
CLR1
RESET OUT
(other reset sources)
TEB1
CLR - Clear 128 bytes
internal RAM on tamper
Time stamp tamper
event (to RTC)
TIE2
TP2
CLR2EXT
TEB2
CLR2
AI07821
Figure 15. Basic tamper detect options
Triggering Event
Tamper Event Output
VCC (VOUT)
TCMX, TPMX = 1,1
TIEX
TAMPER HI,
NORMALLY OPEN
IRQ - Interrupt the
processor on tamper
VCC (VOUT)
TCMX, TPMX = 0,0
User
Configuration
TAMPER LO,
NORMALLY CLOSED
TCMX, TPMX = 1,0
CLRXEXT
TPCLR - Clear external
RAM on tamper
CLRX
TAMPER LO,
NORMALLY OPEN
CLR - Clear internal
RAM on tamper
VCC (VOUT)
TCMX, TPMX
Time stamp tamper
event
TCMX, TPMX = 0,1
TAMPER HI,
NORMALLY CLOSED
AI07818
20/48
M41ST87Y, M41ST87W
2.6.6
Operating modes
Tamper detect sampling (TDS1 and TDS2)
This bit selects between a 1Hz sampling rate or constant monitoring of the tamper input
pin(s) to detect a tamper event when the normally closed switch mode is selected. This
allows the user to reduce the current drain when the TEBX bit is enabled while the device is
in battery backup (see Table 4 on page 22 and Figure 16 on page 22). Sampling is disabled
if the TCMX bit is set to logic '1' (Normally Open). In this case the state of the TDSX bit is a
“Don’t care.”
Note:
The crystal oscillator must be “on” for sampling to be enabled.
2.6.7
Tamper current high/tamper current low (TCHI/TCLO1 and
TCHI/TCLO2)
This bit selects the strength of the internal pull-up or pull-down used during the sampling of
the normally closed condition. The state of the TCHI/TCLOX bit is a “Don’t care” for normally
open (TCMX = '1') mode (see Figure 17 on page 23).
2.6.8
RAM clear (CLR1 and CLR2)
When either of these bits and the TEBX bit are set to a logic '1,' the internal 128 bytes of
user RAM (see Figure 14 on page 20) will be cleared to all zeros in the event of a tamper
condition. The 128 bytes of user RAM will be deselected (invalid data will be read) until the
corresponding TEBX bit is reset to '0.'
2.6.9
RAM clear external (CLR1EXT and CLR2EXT)
When either of these bits are set to a logic '1' and the TEBX bit is also set to logic '1,' the
external SRAM will be cleared and the RST output enabled (see Figure 14 on page 20 and
Figure 19 on page 24).
Note:
The reset output resulting from a tamper event will be the same as a reset resulting from a
power-down condition, a watchdog time-out, or a manual reset (RSTIN1 or RSTIN2).
This is accomplished by forcing TPCLR high, which if used to control the inhibit pin of the DC
regulator (see Figure 19 on page 24) will also switch off VOUT, depriving the external SRAM
of power to the VCC pin. VOUT will automatically be disconnected from the battery if the
tamper occurs during battery back-up (see Figure 18 on page 23). By inhibiting the DC
regulator, the user will also prevent other inputs from sourcing current to the external SRAM,
allowing it to retain data.
The user may optionally connect an inverting charge pump to the VCC pin of the external
SRAM (see Figure 19 on page 24). Depending on the process technology used for the
manufacturing of the external SRAM, clearing the memory may require varying durations of
negative potential on the VCC pin. This device configuration will allow the user to program
the time needed for their particular application. Control Bits CLRPW0 and CLRPW1
determine the duration TPCLR will be enabled (see Figure 18 on page 23 and Table 5 on
page 24).
Note:
When using the inverting charge pump, the user must also provide isolation in the form of
two additional small-signal power MOSFETs. These will isolate the VOUT pin from both the
negative voltage generated by the charge pump during a tamper condition, and from being
pulled to ground by the output of the charge pump when it is in shut-down mode (SHDN =
logic low). The gates of both MOSFETs should be connected to TPCLR as shown in
Figure 19 on page 24. One n-channel enhancement MOSFET should be placed between
21/48
Operating modes
M41ST87Y, M41ST87W
the output of the inverting charge pump and the VOUT of the M41ST87. The other MOSFET
should be an enhancement mode p-channel, and placed between VOUT of the M41ST87
and VCC of the external SRAM. When TPCLR goes high after a tamper condition occurs, the
n-channel MOSFET will turn on and the p-channel will turn off. During normal operating
conditions, TPCLR will be low and the p-channel will be on, while the n-channel will be off.
Table 4.
Tamper detection current (normally closed - TCMX = '0')
TDSX
TCHI/TCLOX
Tamper circuit mode
Current at 3.0 V (typ)(1)(2)
Unit
0
0
Continuous monitoring / 10 MΩ pull-up/-down
0.3
µA
0
1
Continuous monitoring / 1 MΩ pull-up/-down
3.0
µA
1
0
Sampling (1Hz) / 10 MΩ pull-up/-down
0.3
nA
1
1
Sampling (1Hz) / 1 MΩ pull-up/-down
3.0
nA
1. When calculating battery lifetime, this current should be added to IBAT current listed in Table 17 on page 42.
2. Per tamper detect input
Figure 16. Tamper detect sampling options
VCC (VOUT)
CONTINUOUS
MONITORING
TAMPER HI,
NORMALLY OPEN
VCC (VOUT)
CONTINUOUS
MONITORING
SAMPLED
MONITORING
TAMPER LO,
NORMALLY CLOSED
TDSX = 0
User
Configuration
TDSX = 1
TCMX, TPMX
CONTINUOUS
MONITORING
TAMPER LO,
NORMALLY OPEN
VCC (VOUT)
CONTINUOUS
MONITORING
TAMPER HI,
NORMALLY CLOSED
SAMPLED
MONITORING
TDSX = 0
TDSX = 1
AI07819
22/48
M41ST87Y, M41ST87W
Operating modes
Figure 17. Tamper current options
VCC (VOUT)
CONTINUOUS
MONITORING
TAMPER HI,
NORMALLY OPEN
VCC (VOUT)
CONTINUOUS
MONITORING
TAMPER LO,
NORMALLY CLOSED
TCHI/TCLO = 1
TCHI/TCLO = 0
1MΩ
10MΩ
SAMPLED
MONITORING
TDSX = 0
User
Configuration
TDSX = 1
User Configuration
TCMX, TPMX
TPX (TP1, TP2)
CONTINUOUS
MONITORING
VCC (VOUT)
TAMPER LO,
NORMALLY OPEN
1MΩ
10MΩ
TCHI/TCLO = 1
TCHI/TCLO = 0
User Configuration
CONTINUOUS
MONITORING
SAMPLED
MONITORING
TAMPER HI,
NORMALLY CLOSED
TDSX = 0
TDSX = 1
AI07820
Figure 18. Tamper output timing (with CLR1EXT or CLR2EXT = '1')
TPCLR
tCLRD
tCLR
trec
RST
VOUT(1)
High-Z(2)
IRQ/OUT(3)
(4)
High-Z
ECON
Tamper
Event
(TB Bit set)
AI07083
1. If connected to a negative charge pump device, this pin must be isolated from the charge pump by using both n-channel
and p-channel MOSFETs as illustrated in Figure 19 on page 24.
2. If the device is in battery back-up; NOT on VCC (see Section 2.6.9: RAM clear external (CLR1EXT and CLR2EXT) on
page 21).
3. If TIEX = '1.'
4. If ABE = '1.'
23/48
Operating modes
Table 5.
M41ST87Y, M41ST87W
Tamper detect timing
Symbol
Parameter
CLRPW
1
CLRPW
0
Min
Typ
Max
Unit
tCLRD(1)
Tamper RAM clear ext delay
X
X
1.0(2)
1.5
2.0
ms
0
0
1
s
0
1
4
s
1
0
8
s
1
1
16
s
tCLR
Tamper clear timing
1. With input capacitance = 70 pF and resistance = 50 Ω.
2. If the OF bit is set, tCLRD(min) = 0.5 ms.
Figure 19. RAM clear hardware hookup
Inverting
Charge
Pump
IN
Negative Output
(–1 x VIN)
OUT
SHDN
Inhibit
VIN
VCC
5V
Regulator
(1)
M41ST87Y/W
VCC
TPCLR
CAP+ CAP–
TP1IN
(2)
TP2IN
VOUT
VCC
SCL
ECON
E
WDI
SDA
RSTIN1
RST
RSTIN2
SQW/FT
EX
Pushbutton
Reset
PFO1
PFI1
Low-Power
SRAM
To RST
To LED Display
To NMI
PFO2
PFI2
VSS
VBAT
IRQ/OUT
F32k
To INT
To 32kHz
AI07804
1. Most inverting charge pumps drive OUT to ground when device shut down is enabled (SHDN = logic low). Therefore, an nchannel enhancement mode MOSFET should be used to isolate the OUT pin from the VOUT of the M41ST87.
2. In order to avoid turning on an on-chip parasitic diode when driving VOUT negative, a p-channel enhancement mode
MOSFET should be used to isolate the VOUT pin from the negative voltage generated by the inverting charge pump.
2.7
Tamper detection operation
The tamper pins are triggered based on the state of an external switch. Two switch mode
options are available, “normally open” or “normally closed,” based on the setting of the
24/48
M41ST87Y, M41ST87W
Operating modes
tamper connect mode bit (TCMX). If the selected switch mode is normally open (TCMX = '1'),
the tamper pin will be triggered by being connected to VSS (if the TPMX bit is set to '0') or to
VCC (if the TPMX bit is set to '1'), through the closing of the external switch. When the
external switch is closed, the tamper bit will be immediately set, allowing the user to
determine if the device has been physically tampered with. If the selected switch mode is
normally closed (TCMX = '0'), the tamper pin will be triggered by being pulled to VSS or to
VOUT (depending on the state of the TPMX bit), through an internal pull-up/pull-down resistor
as a result of opening the external switch.
When a tamper event occurs, the tamper bits (TB1 and/or TB2) will be immediately set if
TEBX = '1.'
If the tamper interrupt enable bit (TIEX) is set to a '1,' the IRQ/OUT pin will also be activated.
The IRQ/OUT output is cleared by a READ of the flags register (as seen in Figure 23 on
page 33), a reset of the TIE bit to '0,' or the RST output is enabled.
Note:
In order to avoid an inadvertent activation of the IRQ/OUT pin due to a prior tamper event,
the flag register (0Fh) should be read prior to resetting the TEBX bit.
The tamper bits are “read only” bits and are reset only by writing the tamper enable bit
(TEBX) to '0.'
The tamper detect function operates both under normal power, and in battery backup. Even
if the trigger event occurs during a power-down condition, the bit will be set correctly.
2.8
Sampling
As the switch mode normally closed (TCMX = '0') requires a greater amount of current to
maintain constant monitoring, the M41ST87Y/W offers a programmable tamper detect
sampling bit (TDSX) to reduce the current drawn on VCC or VBAT (see Figure 16 on
page 22). When enabled, the sampling frequency is once per second (1Hz), for
approximately 1 ms.
When TEBX is disabled, no current will be drawn by the tamper detection circuit. After a
tamper event has been detected, no additional current will be drawn.
Note:
The oscillator must be running for tamper detection to operate in the sampling mode. If the
oscillator is stopped, the tamper detection circuit will revert to constant monitoring.
Note:
Sampling in the tamper high mode (TPMX = '1') may be bypassed while on VCC by
connecting the TPXIN pin to VCC through an external resistor. This will allow constant
monitoring when VCC is “on” and revert to sampling when in battery backup (see Figure 13
on page 19).
2.9
Internal tamper pull-up/down current
Depending on the capacitive and resistive loading of the tamper pin input (TPXIN), the user
may require more or less current from the internal pull-up/down used when monitoring the
normally closed switch mode. The state of the tamper current hi/tamper current low bit
(TCHI/TCLOX) determines the sizing of the internal pull-up/-down. TCHI/TCLOX = '1' uses a
1 MΩ pull-up/-down resistor, while TCHI/TCLOX = '0' uses a 10 MΩ pull-up/-down resistor
(see Figure 17 on page 23).
25/48
Operating modes
2.10
M41ST87Y, M41ST87W
Avoiding inadvertent tampers (normally closed
configuration)
In some applications it may be necessary to use a low pass filter to reduce electrical noise
on the tamper input pin when the TCMX bit = 0 (normally closed). This is especially true if
the tamper detect switch is located some distance (> 6”) from the tamper input pin. A low
pass filter can prevent unwanted, higher frequency noise from inadvertently being detected
as a tamper condition caused by the “antenna-effect” (produced by a longer signal wire or
mesh). This low pass filter can be constructed using a series resistor (R) in conjunction with
a capacitor (C) on the tamper input pin.
The cut-off frequency fc is determined according to the formula:
f c = 1 ⁄ ( 2 ⋅ Pi ⋅ R ⋅ C )
Figure 20. Low-pass filter implementation for noise immunity
TPIN
To Tamper Detect Switch
R
C
AI11185
Table 6.
26/48
Calculated cut-off frequency for typical capacitance and resistance
values
R (Ω)
C (F)
fc
1/fc (s)
1000
1.00E-09
15.9 MHz
6.28 µs
1000
1.00E-06
159.2 Hz
6.28 ms
5000
1.00E-09
31.8 kHz
31.4 µs
5000
1.00E-06
31.8 Hz
31.4 ms
10000
1.00E-09
15.9 kHz
62.8 µs
10000
1.00E-06
15.9 Hz
62.8 ms
M41ST87Y, M41ST87W
2.11
Operating modes
Tamper event time-stamp
Regardless of which tamper occurs first, not only will the appropriate tamper bit be set, but
the event will also be automatically time-stamped. This is accomplished by freezing the
normal update of the clock registers (00h through 07h) immediately following a tamper
event. Thus, when tampering occurs, the user may first read the time registers to determine
exactly when the tamper event occurred, then re-enable the clock update to the current time
(and reset the tamper bit, TBX) by resetting the tamper enable bit (TEBX).
The time update will then resume and the clock can be read to determine the current time.
Both tamper enable bits (TEBX) must always be set to '0' in order to read the current time.
In the event of multiple tampers, the time-stamp will reflect the initial tamper event.
Note:
If the TEBX bit is set, the tamper event time-stamp will take precedence over the power
down time-stamp (see Section 3.0.1: Power-down time-stamp on page 28) and the HT bit
(halt update) will not be set during the power-down event. If both are needed, the power
down time-stamp may be accomplished by writing the time into the general purpose RAM
memory space when PFO is asserted.
27/48
Clock operation
3
M41ST87Y, M41ST87W
Clock operation
The eight byte clock register (see Table 7 on page 29) is used to both set the clock and to
read the date and time from the clock, in a binary coded decimal format. Tenths/hundredths
of seconds, seconds, minutes, and hours are contained within the first four registers.
Note:
A WRITE to any clock register will result in the tenths/hundredths of seconds being reset to
“00,” and tenths/hundredths of seconds cannot be written to any value other than “00.”
Bits D6 and D7 of clock register 03h (century/hours register) contain the CENTURY bit 0
(CB0) and CENTURY bit 1 (CB1). Bits D0 through D2 of register 04h contain the day (day of
week). Registers 05h, 06h, and 07h contain the date (day of month), month, and years. The
ninth clock register is the control register (this is described in the clock calibration section).
Bit D7 of register 01h contains the STOP bit (ST). Setting this bit to a '1' will cause the
oscillator to stop. If the device is expected to spend a significant amount of time on the shelf,
the oscillator may be stopped to reduce current drain. When reset to a '0' the oscillator
restarts within one second (typical).
Note:
A WRITE to ANY location within the first eight bytes of the clock register (00h-07h),
including the OFIE bit, CLRPW0 bit, CLRPW1 bit, THS bit, and so forth, will result in an
update of the system clock and a reset of the divider chain. This could result in a significant
corruption of the current time, especially if the HT bit (see Section 3.0.1: Power-down timestamp) has not been previously reset. These non-clock related bits should be written prior to
setting the clock, and remain unchanged until such time as a new clock time is also written.
The eight clock registers may be read one byte at a time, or in a sequential block. The
control register (address location 08h) may be accessed independently. Provision has been
made to assure that a clock update does not occur while any of the eight clock addresses
are being read. If a clock address is being read, an update of the clock registers will be
halted. This will prevent a transition of data during the READ.
3.0.1
Power-down time-stamp
Upon power-up following a power failure, the halt update bit (HT) will automatically be set to
a '1.' This will prevent the clock from updating the TIMEKEEPER® registers, and will allow
the user to read the time of the power-down event.
Note:
When the HT bit is set or a tamper event occurs, the tenths/hundredths of a second register
(00h) will automatically be reset to a value of “00.” All other date and time registers (01h 07h) will retain the value last updated prior to the power-down or tamper event. The internal
clock remains accurate and no time is lost as a result of the zeroing of the tenth/hundredths
of a second register. When updates are resumed (due to resetting the HT bit or TEB bit), the
correct time will be displayed.
Resetting the HT bit to a '0' will allow the clock to update the TIMEKEEPER registers with
the current time.
Note:
28/48
If the TEB bit is set, the power down time-stamp will be disabled, and the tamper event timestamp will take precedence (see Section 2.7: Tamper detection operation on page 24).
M41ST87Y, M41ST87W
3.1
Clock operation
TIMEKEEPER® registers
The M41ST87Y/W offers 22 internal registers which contain clock, control, alarm, watchdog,
flag, square wave, and tamper data. The clock registers are memory locations which contain
external (user accessible) and internal copies of the data (usually referred to as BiPORT™
TIMEKEEPER cells). The external copies are independent of internal functions except that
they are updated periodically by the simultaneous transfer of the incremented internal copy.
The internal divider (or clock) chain will be reset upon the completion of a WRITE to any
clock address (00h to 07h).
The system-to-user transfer of clock data will be halted whenever the address being read is
a clock address (00h to 07h). The update will resume either due to a stop condition or when
the pointer increments to a non-clock or RAM address.
TIMEKEEPER and alarm registers store data in BCD format. Control, watchdog and square
wave registers store data in binary format.
Table 7.
TIMEKEEPER® register map
Data
Function/range
Addr
D7
00h
D6
D5
D4
D3
0.1 seconds
01h
02h
ST
OFIE
03h
CB1
CB0
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
12h
13h
TR
PFOD
0
THS
0
0
14h
TEB1
15h
TEB2
OUT
WDS
AFE
RPT4
RPT3
RPT2
RPT1
WDF
0
0
0
RS3
D1
D0
0.01 seconds
10 seconds
10 minutes
Seconds
Minutes
10 hours
Hours (24-hour format)
CLRPW1 CLRPW0
32kE
Day of week
10 date
Date: day of month
0
10M
Month
10 Years
Year
FT
S
Calibration
BMB4
BMB3
BMB2
BMB1
BMB0
RB1
RB0
SQWE
ABE
Al 10M
Alarm month
RPT5
AI 10 date
Alarm date
HT
AI 10 hour
Alarm hour
Alarm 10 minutes
Alarm minutes
Alarm 10 seconds
Alarm seconds
AF
0
BL
0
OF
TB1
TB2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
RS2
RS1
RS0
SQWOD
0
0
0
TCHI/
TIE1
TCM1
TPM1
TDS1
CLR1EXT CLR1
TCLO1
TCHI/
TIE2
TCM2
TPM2
TDS2
CLR2EXT CLR2
TCLO2
16h-1Dh
ROM
1Eh-1Fh
Reserved
20h-9Fh
D2
BCD format
10s/100s
seconds
Seconds
Minutes
Century/
Hours
Day
Date
Month
Year
Control
Watchdog
Al month
Al date
Al hour
Al min
Al sec
Flags
Reserved
Reserved
Reserved
SQW
00-99
00-59
00-59
0-1/
00-23
01-7
01-31
01-12
00-99
01-12
01-31
00-23
00-59
00-59
Tamper1
Tamper2
Serial
number
8-byte
2-byte
128 user
bytes
29/48
Clock operation
M41ST87Y, M41ST87W
Keys:
0 = Must be set to zero
RB0-RB1 = Watchdog resolution bits
32kE = 32 kHz output enable bit
RPT1-RPT5 = Alarm repeat mode bits
ABE = Alarm in battery backup mode enable bit RS0-RS3 = SQW frequency
AF = Alarm flag (read only)
S = Sign bit
AFE = Alarm flag enable bit
SQWE = Square wave enable
BL = Battery low flag (read only)
SQWOD = Square wave open drain bit
BMB0-BMB4 = Watchdog multiplier bits
ST = Stop bit
CB0-CB1 = Century bits
TB (1 and 2) = Tamper bits (read only)
CLR (1 and 2) = RAM clear bits
TCHI/TCLO (1 and 2) = Tamper current hi/tamper current low bits
CLR (1 and 2)EXT = RAM clear external bits
TCM (1 and 2) = Tamper connect mode bits
CLRPW0 = RAM clear pulse width 0 bit
TDS (1 and 2) = Tamper detect sampling bits
CLRPW1 = RAM clear pulse width 1 bit
TEB (1 and 2) = Tamper enable bits
FT = Frequency test bit
THS = Threshold bit
HT = Halt update bit
TIE (1 and 2) = Tamper interrupt enable bits
OF = Oscillator fail bit
TPM (1 and 2) = Tamper polarity mode bits
OFIE = Oscillator fail interrupt enable bit
TR = trec bit
OUT = Output level
WDS = Watchdog steering bit
PFOD = Power-fail output open drain bit
WDF = Watchdog flag (read only)
3.2
Calibrating the clock
The M41ST87Y/W is driven by a quartz controlled oscillator with a nominal frequency of
32,768 Hz. The devices are tested not exceed ±35 ppm (parts per million) oscillator
frequency error at 25oC, which equates to about ±1.53 minutes per month. When the
Calibration circuit is properly employed, accuracy improves to better than ±2 ppm at 25°C.
The oscillation rate of crystals changes with temperature (see Figure 21 on page 31).
Therefore, the M41ST87Y/W design employs periodic counter correction. The calibration
circuit adds or subtracts counts from the oscillator divider circuit at the divide by 256 stage,
as shown in Figure 22: Calibration waveform on page 32. The number of times pulses which
are blanked (subtracted, negative calibration) or split (added, positive calibration) depends
upon the value loaded into the five calibration bits found in the control register. Adding
counts speeds the clock up, subtracting counts slows the clock down.
The calibration bits occupy the five lower order bits (D4-D0) in the control register (08h).
These bits can be set to represent any value between 0 and 31 in binary form. Bit D5 is a
sign bit; '1' indicates positive calibration, '0' indicates negative calibration. Calibration occurs
within a 64 minute cycle. The first 62 minutes in the cycle may, once per minute, have one
second either shortened by 128 or lengthened by 256 oscillator cycles. If a binary '1' is
loaded into the register, only the first 2 minutes in the 64 minute cycle will be modified; if a
binary 6 is loaded, the first 12 will be affected, and so on.
Therefore, each calibration step has the effect of adding 512 or subtracting 256 oscillator
cycles for every 125,829,120 actual oscillator cycles, that is +4.068 or –2.034 ppm of
30/48
M41ST87Y, M41ST87W
Clock operation
adjustment per calibration step in the calibration register. Assuming that the oscillator is
running at exactly 32,768 Hz, each of the 31 increments in the calibration byte would
represent +10.7 or –5.35 seconds per month which corresponds to a total range of +5.5 or
–2.75 minutes per month.
Two methods are available for ascertaining how much calibration a given M41ST87Y/W may
require.
The first involves setting the clock, letting it run for a month and comparing it to a known
accurate reference and recording deviation over a fixed period of time. Calibration values,
including the number of seconds lost or gained in a given period, can be found in application
note AN934, “TIMEKEEPER® calibration.” This allows the designer to give the end user the
ability to calibrate the clock as the environment requires, even if the final product is
packaged in a non-user serviceable enclosure. The designer could provide a simple utility
that accesses the calibration byte.
The second approach is better suited to a manufacturing environment, and involves the use
of the SQW/FT pin. The pin will toggle at 512 Hz, when the stop bit (ST) is '0,' the frequency
test bit (FT) is '1,' and SQWE is '0.'
Any deviation from 512 Hz indicates the degree and direction of oscillator frequency shift at
the test temperature. For example, a reading of 512.010124 Hz would indicate a +20 ppm
oscillator frequency error, requiring a –10 (XX001010) to be loaded into the calibration byte
for correction. Note that setting or changing the calibration byte does not affect the
frequency test output frequency.
If the SQWOD Bit = '1,' the SQW/FT pin is an open drain output which requires a pull-up
resistor to VCC for proper operation. A 500 to10 k resistor is recommended in order to
control the rise time. The FT bit is cleared on power-down.
Figure 21. Crystal accuracy across temperature
Frequency (ppm)
20
0
–20
–40
–60
ΔF = K x (T – T )2
O
F
–80
2
2
K = –0.036 ppm/°C ± 0.006 ppm/°C
–100
TO = 25°C ± 5°C
–120
–140
–160
–40
–30
–20
–10
0
10
20
30
40
50
60
70
80
Temperature °C
AI07888
31/48
Clock operation
M41ST87Y, M41ST87W
Figure 22. Calibration waveform
NORMAL
POSITIVE
CALIBRATION
NEGATIVE
CALIBRATION
AI00594B
3.3
Setting alarm clock registers
Address locations 0Ah-0Eh contain the alarm settings. The alarm can be configured to go
off at a prescribed time on a specific month, date, hour, minute, or second, or repeat every
year, month, day, hour, minute, or second. It can also be programmed to go off while the
M41ST87Y/W is in the battery back-up to serve as a system wake-up call.
Bits RPT5–RPT1 put the alarm in the repeat mode of operation. Table 8 on page 33 shows
the possible configurations. Codes not listed in the table default to the once per second
mode to quickly alert the user of an incorrect alarm setting.
When the clock information matches the alarm clock settings based on the match criteria
defined by RPT5–RPT1, the AF (alarm flag) is set. If AFE (alarm flag enable) is also set, the
alarm condition activates the IRQ/OUT pin as shown in Figure 24 on page 33. To disable
alarm, write '0' to the alarm date register and to RPT5–RPT1.
If the address pointer is allowed to increment to the flag register address, an alarm condition
will not cause the interrupt/flag to occur until the address pointer is moved to a different
address. It should also be noted that if the last address written is the “alarm seconds,” the
address pointer will increment to the flag address, causing this situation to occur.
The IRQ/OUT output is cleared by a READ to the flags register. A subsequent READ of the
flags register is necessary to see that the value of the alarm flag has been reset to '0.'
The IRQ/OUT pin can also be activated in the battery backup mode. The IRQ/OUT will go
low if an alarm occurs and both ABE (alarm in battery backup mode enable) and AFE are
set. The ABE and AFE bits are reset during power-up, therefore an alarm generated during
power-up will only set AF. The user can read the flag register at system boot-up to
determine if an alarm was generated while the M41ST87Y/W was in the deselect mode
during power-up. Figure 24 on page 33 illustrates the backup mode alarm timing.
32/48
M41ST87Y, M41ST87W
Clock operation
Figure 23. Alarm interrupt reset waveform
0Eh
0Fh
10h
ACTIVE FLAG
HIGH-Z
IRQ/OUT
AI07086
Table 8.
Alarm repeat modes
RPT5
RPT4
RPT3
RPT2
RPT1
Alarm setting
1
1
1
1
1
Once per second
1
1
1
1
0
Once per minute
1
1
1
0
0
Once per hour
1
1
0
0
0
Once per day
1
0
0
0
0
Once per month
0
0
0
0
0
Once per year
Figure 24. Backup mode alarm waveform
VCC
VPFD
VSO
trec
ABE, AFE Bits in Interrupt Register
AF bit in Flags Register
IRQ/OUT
HIGH-Z
HIGH-Z
AI07087
33/48
Clock operation
3.4
M41ST87Y, M41ST87W
Watchdog timer
The watchdog timer can be used to detect an out-of-control microprocessor. The user
programs the watchdog timer by setting the desired amount of time-out into the watchdog
register, address 09h. Bits BMB4-BMB0 store a binary multiplier and the two lower order bits
RB1-RB0 select the resolution, where 00=1/16 second, 01=1/4 second, 10=1 second, and
11=4 seconds. The amount of time-out is then determined to be the multiplication of the fivebit multiplier value with the resolution. (For example: writing 00001110 in the watchdog
register = 3*1 or 3 seconds).
Note:
The accuracy of the timer is within ± the selected resolution.
If the processor does not reset the timer within the specified period, the M41ST87Y/W sets
the WDF (watchdog flag) and generates a watchdog interrupt or a microprocessor reset.
The most significant bit of the watchdog register is the watchdog steering bit (WDS). When
set to a '0,' the watchdog will activate the IRQ/OUT pin when timed-out. When WDS is set to
a '1,' the watchdog will output a negative pulse on the RST pin for trec. The watchdog
register, FT, AFE, ABE and SQWE bits will reset to a '0' at the end of a watchdog time-out
when the WDS bit is set to a '1.'
The watchdog timer can be reset by two methods: 1) a transition (high-to-low or low-to-high)
can be applied to the watchdog input pin (WDI) or 2) the microprocessor can perform a
WRITE of the watchdog register. The time-out period then starts over.
Note:
The WDI pin should be tied to VSS if not used.
In order to perform a software reset of the watchdog timer, the original time-out period can
be written into the watchdog register, effectively restarting the count-down cycle.
Should the watchdog timer time-out, and the WDS bit is programmed to output an interrupt,
either a transition of the WDI pin, or a value of 00h needs to be written to the watchdog
register in order to clear the IRQ/OUT pin. This will also disable the watchdog function until
it is again programmed correctly. A READ of the flags register will reset the watchdog flag
(bit D7; register 0Fh).
The watchdog function is automatically disabled upon power-up and the watchdog register
is cleared.
3.5
Square wave output
The M41ST87Y/W offers the user a programmable square wave function which is output on
the SQW/FT pin. RS3-RS0 bits located in 13h establish the square wave output frequency.
These frequencies are listed in Table 9. Once the selection of the SQW frequency has been
completed, the SQW/FT pin can be turned on and off under software control with the square
wave enable bit (SQWE) located in Register 0Ah.
The SQW/FT output is programmable as an N-channel, open drain output driver, or a fullCMOS output driver. By setting the square wave open drain bit (SQWOD) to a '1,' the output
will be configured as an open drain (with IOL as specified in Table 17 on page 42). When
SQWOD is set to '0,' the output will be configured as full-CMOS (sink and source current as
specified in Table 17 on page 42).
Note:
34/48
When configured as open drain (SQWOD = '1'), the SQW/FT pin requires an external pullup resistor.
M41ST87Y, M41ST87W
Table 9.
Clock operation
Square wave output frequency
Square wave bits
3.6
Square wave
RS3
RS2
RS1
RS0
Frequency
Units
0
0
0
0
None
–
0
0
0
1
32.768
kHz
0
0
1
0
8.192
kHz
0
0
1
1
4.096
kHz
0
1
0
0
2.048
kHz
0
1
0
1
1.024
kHz
0
1
1
0
512
Hz
0
1
1
1
256
Hz
1
0
0
0
128
Hz
1
0
0
1
64
Hz
1
0
1
0
32
Hz
1
0
1
1
16
Hz
1
1
0
0
8
Hz
1
1
0
1
4
Hz
1
1
1
0
2
Hz
1
1
1
1
1
Hz
Full-time 32 kHz square wave output
The M41ST87Y/W offers the user a special 32kHz square wave function which defaults to
output on the F32k pin (pin 21) as long as VCC ≥ VSO, and the oscillator is running (ST bit =
'0'). This function is available within one second (typ) of initial power-up and can only be
disabled by setting the 32 kE bit to '0' or the ST bit to '1.' If not used, the F32k pin should be
disconnected and allowed to float.
Note:
The F32k pin is an open drain which requires an external pull-up resistor.
3.7
Power-on reset
The M41ST87Y/W continuously monitors VCC. When VCC falls to the power fail detect trip
point, the RST pulls low (open drain) and remains low on power-up for trec after VCC passes
VPFD(max). The RST pin is an open drain output and an appropriate pull-up resistor should
be chosen to control rise time.
Note:
A power-on reset will result in resetting the following control bits to '0': OFIE, AFE, ABE,
SQWE, FT, WDS, BMB0-BMB4, RB0, RB1, TIE1, and TIE2 (see Table 13 on page 39).
3.8
Reset inputs (RSTIN1 & RSTIN2)
The M41ST87Y/W provides two independent inputs which can generate an output reset.
The function of these resets is identical to a reset generated by a power cycle. Table 10 and
Figure 25 illustrate the AC reset characteristics of this function. Pulses shorter than tR1 and
35/48
Clock operation
M41ST87Y, M41ST87W
tR2 will not generate a reset condition. RSTIN1 and RSTIN2 are each internally pulled up to
VCC through a 100 kΩ resistor.
Figure 25. RSTIN1 & RSTIN2 timing waveforms
RSTIN1
tR1
RSTIN2
tR2
Hi-Z
Hi-Z
RST
trec
trec
AI07072
Table 10.
Reset AC characteristics
Parameter(1)
Symbol
tR1
(2)
tR2
(2)
trec(3)
Min
Max
Unit
RSTIN1 low to RST low (min pulse width)
100
200
ns
RSTIN2 low to RSTIN2 high (min pulse width)
100
200
ns
RSTIN1 or RSTIN2 high to RST high
96
98(3)
ms
1. Valid for ambient operating temperature: TA = –40 to 85°C; VCC = 4.5 to 5.5 V or 2.7 to 3.6 V (except where
noted).
2. Pulse widths of less than 100 ns will result in no RESET (for noise immunity).
3. Programmable (see Table 12 on page 39). Same function as power-on reset.
3.9
Power-fail comparators (1 and 2)
Two power-fail inputs (PFI1 and PFI2) are compared to an internal reference voltage (1.25V).
If either PFI1 or PFI2 is less than the power-fail threshold (VPFI), the associated power-fail
output (PFO1 or PFO2) will go low. This function is intended for use as an under-voltage
detector to signal a failing power supply. Typically PFI1 and PFI2 are connected through
external voltage dividers (see Figure 4 on page 10) to either the unregulated DC input (if it is
available) or the regulated output of the VCC regulator. The voltage divider can be set up
such that the voltage at PFI1 or PFI2 falls below VPFI several milliseconds before the
regulated VCC input to the M41ST87Y/W or the microprocessor drops below the minimum
operating voltage.
During battery back-up, the power-fail comparator turns off and PFO1 and PFO2 go (or
remain) low. This occurs after VCC drops below VPFD(min). When power returns, PFO1 and
PFO2 are forced high, irrespective of VPFI for the write protect time (trec), which is the time
from VPFD(max) until the inputs are recognized. At the end of this time, the power-fail
comparator is enabled and PFO1 and PFO2 follow PFI1 and PFI2. If the comparator is
unused, PFI1 or PFI2 should be connected to VSS and the associated PFO1 or PFO2 left
unconnected.
3.10
Power-fail outputs
The PFO1 and PFO2 outputs are programmable as N-channel, open drain output drivers, or
full-CMOS output drivers. By setting the power-fail output open drain bit (PFOD) to a '1,' the
36/48
M41ST87Y, M41ST87W
Clock operation
output will be configured as open drain (with IOL as specified in Table 17 on page 42). When
PFOD is set to '0,' the outputs will be configured as full-CMOS (sink and source current as
specified in Table 17 on page 42).
Note:
When configured as open drain (PFOD = '1'), PFO1 and PFO2 will require an external pullup resistor.
3.11
Century bits
These two bits will increment in a binary fashion at the turn of the century, and handle leap
years correctly. See Table 11 on page 38 for additional explanation.
3.12
Output driver pin
When the TIE bit, OFIE bit, AFE bit, and watchdog register are not set to generate an
interrupt, the IRQ/OUT pin becomes an output driver that reflects the contents of D7 of the
control register. In other words, when D7 (OUT Bit) is a '0,' then the IRQ/OUT pin will be
driven low. With the ABE bit set to '1,' the OUT pin will continue to be driven low in battery
backup.
Note:
The IRQ/OUT pin is an open drain which requires an external pull-up resistor.
3.13
Battery low warning
The M41ST87Y/W automatically performs battery voltage monitoring upon power-up and at
factory-programmed time intervals of approximately 24 hours. The battery low (BL) bit, bit
D4 of flags register 0Fh, will be asserted if the battery voltage is found to be less than
approximately 2.5 V. The BL bit will remain asserted until completion of battery replacement
and subsequent battery low monitoring tests, either during the next power-up sequence or
the next scheduled 24-hour interval.
If a battery low is generated during a power-up sequence, this indicates that the battery is
below approximately 2.5 volts and may not be able to maintain data integrity in the SRAM.
Data should be considered suspect and verified as correct. A fresh battery should be
installed.
If a battery low indication is generated during the 24-hour interval check, this indicates that
the battery is near end of life. However, data is not compromised due to the fact that a
nominal VCC is supplied. In order to insure data integrity during subsequent periods of
battery back-up mode, the battery should be replaced. The battery may be replaced while
VCC is applied to the device.
The M41ST87Y/W only monitors the battery when a nominal VCC is applied to the device.
Thus applications which require extensive durations in the battery back-up mode should be
powered-up periodically (at least once every few months) in order for this technique to be
beneficial. Additionally, if a battery low is indicated, data integrity should be verified upon
power-up via a checksum or other technique.
37/48
Clock operation
3.14
M41ST87Y, M41ST87W
trec bit
Bit D7 of clock register 04h contains the trec bit (TR). trec refers to the automatic continuation
of the deselect time after VCC reaches VPFD. This allows for a voltage settling time before
WRITEs may again be performed to the device after a power-down condition. The trec bit will
allow the user to set the length of this deselect time as defined by Table 12 on page 39.
3.15
Electronic serial number
The M41ST87Y/W has a unique 8-byte lasered, serial number with parity. This serial
number is “read only” and is generated such that no two devices will contain an identical
number.
3.16
Oscillator stop detection
If the oscillator fail (OF) bit is internally set to a '1,' this indicates that the oscillator has either
stopped, or was stopped for some period of time and can be used to judge the validity of the
clock and date data. This bit will be set to '1' any time the oscillator stops. The following
conditions can cause the OF bit to be set:
●
The first time power is applied (defaults to a '1' on power-up).
●
The voltage present on VCC or battery is insufficient to support oscillation.
●
The ST bit is set to '1.'
If the oscillator fail interrupt enable bit (OFIE) is set to a '1,' the IRQ/OUT pin will also be
activated. The IRQ/OUT output is cleared by resetting the OF bit to '0,' resetting the OFIE bit
to '0,' or the RST output is enabled (NOT by reading the flag register).
The OF bit will remain set to '1' until written to logic '0.' The oscillator must start and have
run for at least 4 seconds before attempting to reset the OF bit to '0.' This function operates
both under normal power and in battery backup. If the trigger event occurs during a powerdown condition, this bit will be set correctly.
Note:
The ABE bit must be set to '1' for the IRQ/OUT pin to be activated in battery backup.
3.17
Initial power-on defaults
See Table 13 on page 39.
Table 11.
Century bits examples
Example(1)
CB0
CB1
Leap year?
0
0
Yes
2000
0
1
No
2100
1
0
No
2200
1
1
No
2300
1. Leap year occurs every four years (for years evenly divisible by four), except for years evenly divisible by
100. The only exceptions are those years evenly divisible by 400 (the year 2000 was a leap year, year
2100 is not).
38/48
M41ST87Y, M41ST87W
Table 12.
Clock operation
trec definitions
trec bit (TR)
STOP bit (ST)
0
trec time
Units
Min
Max
0
96
98(1)
ms
0
1
40
200
ms
1
X
50
2000
µs
1. Default setting
Table 13.
Default values
TR
ST
OF
OFIE
HT(1)
Out
FT
AFE
0
0
1
0
1
1
0
0
Subsequent power-up (with
battery backup)(2)(3)
UC
UC
UC
0⇑
1⇓
UC
0⇓
0⇑
Condition
ABE
SQWE
SQWOD
PFOD
Watchdog register(4)
0
0
1
1
0
Subsequent power-up (with
battery backup)(2)(3)
0⇑
0⇑
UC
UC
0⇓
Condition
32kE
THS
TEB1 and 2
TCM1 and 2
TPM1 and 2
TDS1 and 2
Initial power-up
1(5)
0
0
0
0
0
Subsequent power-up (with
battery backup)(2)
UC
UC
UC
UC
UC
UC
Condition
TCHI/TCLO1
and 2
CLR1
and 2
TIE1 and 2
CLRPW0
CLRPW1
CLR1EXT
and
CLR2EXT
0
0
0
0
0
0
UC
UC
0⇑
UC
UC
UC
Condition
Initial power-up
Initial power-up
Initial power-up
Subsequent power-up (with
battery backup)(2)
1. When TEBX is set to '1,' the HT bit will not be set on power-down (tamper time-stamp will have precedence).
2. UC = unchanged.
3. ⇑ = VCC rising; ⇓ = VCC falling.
4. WDS, BMB0-BMB4, RB0, RB1.
5. 32 kHz output valid only on VCC.
Note:
All other control bits are undetermined.
39/48
Maximum ratings
4
M41ST87Y, M41ST87W
Maximum ratings
Stressing the device above the rating listed in the absolute maximum ratings table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the operating sections of
this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
Program and other relevant quality documents.
Table 14.
Absolute maximum ratings
Symbol
Parameter
TSTG
TSLD
(1)
Storage temperature (VCC off, oscillator off)
Lead solder temperature for 10 seconds
Value
Unit
–55 to 125
°C
240
°C
–0.3 to VCC+0.3
V
M41ST87Y
–0.3 to 7.0
V
M41ST87W
–0.3 to 4.6
V
Output current
20
mA
Power dissipation
1
W
VIO
Input or output voltage
VCC
Supply voltage
IO
PD
1. Reflow at peak temperature of 240°C (total thermal budget not to exceed 180°C between 90 to 150
seconds).
Caution:
40/48
Negative undershoots below –0.3 V are not allowed on any pin while in the battery backup
mode.
M41ST87Y, M41ST87W
5
DC and AC parameters
DC and AC parameters
This section summarizes the operating and measurement conditions, as well as the DC and
AC characteristics of the device. The parameters in the following DC and AC Characteristic
tables are derived from tests performed under the measurement conditions listed in the
relevant tables. Designers should check that the operating conditions in their projects match
the measurement conditions when using the quoted parameters.
Table 15.
DC and AC measurement conditions
Parameter
Note:
M41ST87Y
M41ST87W
VCC supply voltage
4.5 to 5.5 V
2.7 to 3.6 V
Ambient operating temperature
–40 to 85°C
–40 to 85°C
Load capacitance (CL)
100 pF
50 pF
Input rise and fall times
≤ 50 ns
≤ 50 ns
Input pulse voltages
0.2 to 0.8VCC
0.2 to 0.8VCC
Input and output timing ref. voltages
0.3 to 0.7VCC
0.3 to 0.7VCC
Output high Z is defined as the point where data is no longer driven.
Figure 26. AC testing input/output waveforms
0.8VCC
0.2VCC
0.7VCC
0.3VCC
AI02568
Note:
50 pF for M41ST87W.
Table 16.
Capacitance
Parameter(1)(2)
Symbol
CIN
COUT(3)
tLP
Min
Max
Unit
Input capacitance
7
pF
Output capacitance
10
pF
Low-pass filter input time constant (SDA and SCL)
50
ns
1. Effective capacitance measured with power supply at 5 V. Sampled only, not 100% tested.
2. At 25°C, f = 1 MHz.
3. Outputs are deselected.
41/48
DC and AC parameters
Table 17.
Sym
M41ST87Y, M41ST87W
DC characteristics
Parameter
Test condition(1)
M41ST87Y
Min
Typ
Battery current
500
TA = 25°C, VCC = 0 V,
OSC ON
IBAT(2)
Battery current
VBAT = 3 V
50
OSC OFF
ICC1 Supply current
f = 400 kHz
Supply current
ICC2
SCL, SDA = VCC – 0.3 V
(standby)
Input leakage
0V ≤ VIN ≤ VCC
current
ILI(3)
Input leakage
–25
2
current (PFI)
Output leakage
0V ≤ VIN ≤ VCC
ILO(4)
current
V
current
IOUT1(5) OUT
VOUT1 > VCC – 0.3 V
(active)
VOUT current
VOUT2 > VBAT – 0.3 V
IOUT2
(battery backup)
Input high
VIH
0.7VCC
voltage
VIL
Input low voltage
–0.3
2.5
3.0
VBAT Battery voltage
Output
high
VOH(7)
2.4
IOH = –1.0 mA
voltage
Pull-up supply
voltage
IRQ/OUT, RST, F32k
(open drain)
V (battery
2.9
VOHB(8) OH
IOUT2 = –1.0 µA(9)
backup)
Output low
IOL = 3.0 mA
voltage
Output low
VOL
voltage
IOL = 10 mA
(open drain)(10)
THS bit = 0
4.20
4.35
Power fail
VPFD
deselect
THS bit = 1
4.50
4.60
VCC = 5 V(Y)
PFI input
1.225 1.250
VPFI1 threshold
VCC = 3 V(W)
PFI hysteresis
PFI rising
20
VCC = 5 V(Y)
PFI input
1.225 1.250
VPFI2 threshold
VCC = 3 V(W)
PFI hysteresis
PFI rising
20
Battery backup
VSO
2.5
switchover
Switch
RSW resistance on
tamper pin
M41ST87W
Max
Min
700
Typ
Max
500
700
50
nA
nA
1.4
0.75
mA
1
0.50
mA
±1
±1
µA
25
nA
±1
±1
µA
175
100
mA
100
100
µA
VCC + 0.3
V
0.3VCC
3.5(6)
V
V
25
–25
2
VCC + 0.3 0.7VCC
0.3VCC
3.5(6)
–0.3
2.5
3.0
2.4
V
5.5
3.6
2.9
V
V
0.4
0.4
V
0.4
0.4
V
4.50
4.75
2.55
2.80
2.62
2.88
2.70
3.00
V
V
1.275
1.225
1.250
1.275
V
20
70
mV
1.250
1.275
V
20
70
mV
70
1.275
70
1.225
2.5
500
V
500
1. Valid for ambient operating temperature: TA = –40 to 85°C; VCC = 4.5 to 5.5 V or 2.7 to 3.6 V (except where noted).
2. Measured with VOUT and ECON open. Not including tamper detection current (see Table 4 on page 22).
3. RSTIN1 and RSTIN2 internally pulled-up to VCC through 100 KΩ resistor. WDI internally pulled-down to VSS through
100 KΩ resistor.
42/48
Unit
W
M41ST87Y, M41ST87W
DC and AC parameters
4. Outputs deselected.
5. External SRAM must match RTC supervisor chip VCC specification.
6. For rechargeable backup, VBAT (max) may be considered VCC.
7. For PFO1 and PFO2 (if PFOD = '0'), SQW/FT (if SQWOD = '0'), and TPCLR pins (CMOS).
8. Conditioned output (ECON) can only sustain CMOS leakage current in the battery backup mode. Higher leakage currents
will reduce battery life.
9. TPCLR output can source –300 µA (typ) for VBAT = 2.9 V.
10. For IRQ/OUT, SQW/FT (if SQWOD = '1'), PFO1 and PFO2 (if PFOD = '1'), RST, SDA, and F32k pins (open drain).
Figure 27. Power down/up mode AC waveforms
VCC
VPFD (max)
VPFD (min)
VSO
tF
tR
tFB
tRB
trec
tPD
PFO
VALID
VALID
INPUTS
RECOGNIZED
DON'T CARE
RECOGNIZED
RST
HIGH-Z
OUTPUTS
VALID
(PER CONTROL INPUT)
VALID
(PER CONTROL INPUT)
ECON
AI07085
43/48
DC and AC parameters
Table 18.
Symbol
tF(2)
tFB
(3)
M41ST87Y, M41ST87W
Power down/up AC characteristics
Parameter(1)
Min
Typ
Max
Unit
VPFD(max) to VPFD(min) VCC fall time
300
µs
VPFD(min) to VSS VCC fall time
10
µs
tPD
EX at VIH before power down
0
µs
tPFD
PFI to PFO propagation delay
15
tR
VPFD(min) to VPFD(max) VCC rise time
10
tRB
VSS to VPFD(min) VCC rise time
1
trec
Power-up deselect time
96
25
µs
µs
98
(4)
1. Valid for ambient operating temperature: TA = –40 to 85°C; VCC = 4.5 to 5.5 V or 2.7 to 3.6 V (except where noted).
2. VPFD(max) to VPFD(min) fall time of less than tF may result in deselection/write protection not occurring until
200 µs after VCC passes VPFD(min).
3. VPFD(min) to VSS fall time of less than tFB may cause corruption of RAM data.
4. Programmable (see Table 12 on page 39)
44/48
µs
ms
M41ST87Y, M41ST87W
6
Package mechanical data
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. ECOPACK® packages are lead-free. The category of second Level Interconnect
is marked on the package and on the inner box label, in compliance with JEDEC Standard
JESD97. The maximum ratings related to soldering conditions are also marked on the inner
box label. ECOPACK is an ST trademark. ECOPACK specifications are available at:
www.st.com.
Figure 28. SOX28 – 28-lead plastic small outline, 300 mils, embedded crystal outline
D
14
h x 45°
1
C
E
15
H
28
A2
A
B
ddd
A1
e
A1
α
L
SO-E
Note:
Drawing is not to scale.
Table 19.
SOX28 – 28-lead plastic small outline, 300 mils, embedded crystal, mechanical data
millimeters
inches
Symbol
Typ
Min
Max
A
2.44
A1
Typ
Min
Max
2.69
0.096
0.106
0.15
0.31
0.006
0.012
A2
2.29
2.39
0.090
0.094
B
0.41
0.51
0.016
0.020
C
0.20
0.31
0.008
0.012
D
17.91
18.01
0.705
0.709
ddd
0.10
E
7.57
7.67
–
–
H
10.16
L
a
N
28
e
1.27
0.004
0.298
0.302
–
–
10.52
0.400
0.414
0.51
0.81
0.020
0.032
0°
8°
0°
8°
0.050
28
45/48
Part numbering
7
M41ST87Y, M41ST87W
Part numbering
Table 20.
Ordering information scheme
Example:
M41ST
87Y
MX
6
Device type
M41ST
Supply voltage and write protect voltage
87Y = VCC = 4.75 to 5.5 V
THS bit = '1': 4.50 V ≤ VPFD ≤ 4.75 V
VCC = 4.5 to 5.5 V
THS bit = '0': 4.20 V ≤ VPFD ≤ 4.50 V
87W = VCC = 3.0 to 3.6 V;
THS bit = '1': 2.80 V ≤ VPFD ≤ 3.00 V
VCC = 2.7 to 3.6 V;
THS bit = '0': 2.55 V ≤ VPFD ≤ 2.70 V
Package
MX(1)(2)= SOX28
Temperature range
6 = –40 to 85°C
Shipping method
blank = ECOPACK® package, tubes
TR = ECOPACK® package, tape & reel
1. The SOX28 package includes an embedded 32,768 Hz crystal.
2. Lead-free second level interconnect and RoHS compliant (by exemption).
For other options, or for more information on any aspect of this device, please contact the
ST sales office nearest you.
46/48
M41ST87Y, M41ST87W
8
Revision history
Revision history
Table 21.
Document revision history
Date
Revision
May-2002
1
Changes
First issue.
23-Apr-2003
2
10-Jul-2003
2.1
Update tamper information ( Figure 3, 4, 13, 14, 15; Table 17, 4, 12).
Document promoted to Preliminary Data.
11-Sep-2003
2.2
Update electrical, charge pump, and clock information (Table 17; Figure 4,
18, 19).
15-Jun-2004
3
Reformatted; added Lead-free information; updated characteristics
(Figure 2; Table 1, 14, 17, 20).
7-Sep-2004
4
Update maximum ratings (Table 14).
29-Jun-2005
5
Clarify NC connections, add Inadvertent Tamper, update MX attribute
(Figure 2, 20; Table 1, 6, 20).
28-Mar-2006
6
Update to “Avoiding Inadvertent Tamper paragraph“ paragraph.
10-Sep-2008
7
Reformatted document and title change; updated cover page, Figure 3,
14, 19, Section 6: Package mechanical data.
47/48
M41ST87Y, M41ST87W
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2008 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
48/48