STB60NF06L STP60NF06L - STP60NF06LFP N-channel 60V - 0.012Ω - 60A - TO-220/D2PAK/TO-220FP STripFET™ II Power MOSFET General features Type VDSS RDS(on) ID STB60NF06L 60V <0.014Ω 60 STP60NF06L 60V <0.014Ω 60A STP60NF06LFP 60V <0.014Ω 60A(1) 3 1. Refer to SOA for the max allowable current values on FP-type due to Rth value ■ Exceptional dv/dt capability ■ 100% avalanche tested ■ Application oriented characterization ■ 175°C operating range ■ Low threshold drive 3 1 1 D2PAK 2 TO-220FP 3 1 2 TO-220 Internal schematic diagram Description This Power MOSFET series realized with STMicroelectronics unique STripFET process has specifically been designed to minimize input capacitance and gate charge. It is therefore suitable as primary switch in advanced highefficiency isolated DC-DC converters for Telecom and Computer application. It is also intended for any application with low gate charge drive requirements. Applications ■ Switching application Order codes Part number Marking Package Packaging STB60NF06LT4 B60NF06L D2 STP60NF06L P60NF06L TO-220 Tube STP60NF06LFP P60NF06LFP TO-220FP Tube June 2006 PAK Rev 3 Tape & reel 1/16 www.st.com 16 Contents STB60NF06L - STP60NF06L - STP60NF06LFP Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 Electrical characteristics (curves) ............................. 6 3 Test circuit 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5 Packing mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2/16 ................................................ 9 STB60NF06L - STP60NF06L - STP60NF06LFP 1 Electrical ratings Electrical ratings Table 1. Absolute maximum ratings Symbol Parameter Value D2PAK TO-220FP TO-220 VDS VDGR VGS Unit Drain-source voltage (VGS = 0) 60 V Drain-gate voltage (RGS = 20 kΩ) 60 V Gate- source voltage ± 15 V ID Drain current (continuous) at TC = 25°C 60 60(1) ID Drain current (continuous) at TC = 100°C 42 42(1) A Drain current (pulsed) 240 240(1) A Total dissipation at TC = 25°C 110 30 W Derating Factor 0.73 0.2 W/°C IDM (2) Ptot dv/dt (3) EAS (4) Peak diode recovery voltage slope 20 V/ns Single pulse avalanche energy 320 mJ VISO Insulation withstand voltage (DC) Tstg Storage temperature Tj A -- 2000 V -65 to 175 °C Max. operating junction temperature 1. Refer to SOA for the max allowable current values on FP-type due to Rth value 2. Pulse width limited by safe operating area. 3. ISD ≤60A, di/dt ≤600A/µs, VDD ≤48V, Tj ≤TJMAX 4. Starting Tj = 25 °C, ID = 30A, VDD = 30V Table 2. Thermal data D2PAK TO-220 Rthj-case Thermal resistance junction-case Rthj-amb Rthj-pcb Tl Thermal resistance junction-ambient Thermal resistance junction-pcb(1) Maximum lead temperature for soldering purpose Max Max Max TO-220FP 1.36 5.0 62.5 35 300 °C/W °C/W °C/W °C 1. Only for SMD, When mounted on 1 inch2 FR-4 board, 2 oz of Cu. 3/16 Electrical characteristics 2 STB60NF06L - STP60NF06L - STP60NF06LFP Electrical characteristics (TCASE=25°C unless otherwise specified) Table 3. On/off states Symbol Parameter V(BR)DSS Drain-source breakdown voltage ID = 250µA, VGS =0 IDSS Zero gate voltage drain current (VGS = 0) VDS = Max rating VDS = Max rating, TC = 125°C IGSS Gate-body leakage current (VDS = 0) VGS = ± 15V VGS(th) Gate threshold voltage VDS = VGS, ID = 250µA RDS(on) Static drain-source on resistance VGS = 5V, ID = 30A VGS = 10V, ID = 30A Table 4. Symbol Test conditions Typ. Max. 60 Unit V 1 10 µA µA ±100 nA 1 V 0.014 0.012 0.016 0.014 Ω Ω Typ. Max. Unit Dynamic Parameter Test conditions gfs (1) Forward transconductance VDS= 15V, ID = 30A Ciss Coss Crss Input capacitance Output capacitance Reverse transfer capacitance td(on) tr td(off) tf Qg Qgs Qgd Min. 20 S VDS = 25V, f = 1MHz, VGS = 0 2000 360 125 pF pF pF Turn-on delay time Rise time Turn-off delay time Fall time VDD = 30V, ID = 30A RG = 4.7Ω VGS = 4.5V (see Figure 15) 35 220 55 30 ns ns ns ns Total gate charge Gate-source charge Gate-drain charge VDD = 48V, ID = 60A, VGS = 4.5V, RG = 4.7Ω (see Figure 16) 35 10 20 1. Pulsed: Pulse duration = 300 µs, duty cycle 1.5 %. 4/16 Min. 66 nC nC nC STB60NF06L - STP60NF06L - STP60NF06LFP Table 5. Symbol Source drain diode Parameter ISDM (1) Source-drain current Source-drain current (pulsed) VSD (2) Forward on voltage ISD trr Qrr IRRM Electrical characteristics Test conditions Min. Typ. ISD = 60A, VGS = 0 Reverse recovery time ISD = 60A, di/dt = 100A/µs, Reverse recovery charge VDD = 30V, Tj = 150°C Reverse recovery current (see Figure 17) 110 250 4.5 Max. Unit 60 240 A A 1.3 V ns nC A 1. Pulse width limited by safe operating area. 2. Pulsed: Pulse duration = 300 µs, duty cycle 1.5 % 5/16 Electrical characteristics STB60NF06L - STP60NF06L - STP60NF06LFP 2.1 Electrical characteristics (curves) Figure 1. Safe operating area Figure 2. Thermal impedance Figure 3. Safe operating area for TO-220FP Figure 4. Thermal impedance for TO-220FP Figure 5. Output characterisics Figure 6. Transfer characteristics 6/16 STB60NF06L - STP60NF06L - STP60NF06LFP Electrical characteristics Figure 7. Transconductance Figure 9. Gate charge vs gate-source voltage Figure 10. Capacitance variations Figure 11. Normalized gate threshold voltage vs temperature Figure 8. Static drain-source on resistance Figure 12. Normalized on resistance vs temperature 7/16 Electrical characteristics Figure 13. Source-drain diode forward characteristics 8/16 STB60NF06L - STP60NF06L - STP60NF06LFP Figure 14. Normalized breakdown voltage temperature STB60NF06L - STP60NF06L - STP60NF06LFP 3 Test circuit Test circuit Figure 15. Switching times test circuit for resistive load Figure 16. Gate charge test circuit Figure 17. Test circuit for inductive load Figure 18. Unclamped Inductive load test switching and diode recovery times circuit Figure 19. Unclamped inductive waveform Figure 20. Switching time waveform 9/16 Package mechanical data 4 STB60NF06L - STP60NF06L - STP60NF06LFP Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 10/16 STB60NF06L - STP60NF06L - STP60NF06LFP Package mechanical data D2PAK MECHANICAL DATA TO-247 MECHANICAL DATA mm. inch DIM. MAX. MIN. A MIN. 4.4 TYP 4.6 0.173 TYP. 0.181 MAX. A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.7 0.93 0.027 0.036 B2 1.14 1.7 0.044 0.067 C 0.45 0.6 0.017 0.023 C2 1.23 1.36 0.048 0.053 D 8.95 9.35 0.352 D1 E 8 10 E1 G 0.368 0.315 10.4 0.393 8.5 0.334 4.88 5.28 0.192 0.208 L 15 15.85 0.590 0.625 L2 1.27 1.4 0.050 0.055 L3 1.4 1.75 0.055 0.068 M 2.4 3.2 0.094 0.126 R 0.4 0º 0.015 4º 3 V2 1 11/16 Package mechanical data STB60NF06L - STP60NF06L - STP60NF06LFP TO-220 MECHANICAL DATA DIM. mm. MIN. inch MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 b 0.61 0.88 0.024 0.034 b1 1.15 1.70 0.045 0.066 c 0.49 0.70 0.019 0.027 D 15.25 15.75 0.60 0.620 E 10 10.40 0.393 0.409 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.194 0.202 F 1.23 1.32 0.048 0.052 H1 6.20 6.60 0.244 0.256 J1 2.40 2.72 0.094 0.107 0.551 L 13 14 0.511 L1 3.50 3.93 0.137 L20 16.40 L30 12/16 TYP 0.154 0.645 28.90 1.137 øP 3.75 3.85 0.147 0.151 Q 2.65 2.95 0.104 0.116 STB60NF06L - STP60NF06L - STP60NF06LFP Package mechanical data TO-220FP MECHANICAL DATA mm. DIM. MIN. A 4.4 inch TYP MAX. MIN. TYP. 4.6 0.173 0.181 MAX. 0.106 B 2.5 2.7 0.098 D 2.5 2.75 0.098 0.108 E 0.45 0.7 0.017 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.7 0.045 0.067 F2 1.15 1.7 0.045 0.067 G 4.95 5.2 0.195 0.204 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 L2 0.409 16 0.630 L3 28.6 30.6 1.126 1.204 L4 9.8 10.6 .0385 0.417 L5 2.9 3.6 0.114 0.141 L6 15.9 16.4 0.626 0.645 9 9.3 0.354 0.366 Ø 3 3.2 0.118 0.126 B D A E L7 L3 L6 F2 H G G1 F F1 L7 L2 L5 1 2 3 L4 13/16 Packing mechanical data 5 STB60NF06L - STP60NF06L - STP60NF06LFP Packing mechanical data D2PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA DIM. mm MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 B0 15.7 15.9 0.618 0.626 MAX. D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 F 11.4 11.6 0.449 0.456 K0 4.8 5.0 0.189 0.197 P0 3.9 4.1 0.153 0.161 P1 11.9 12.1 0.468 0.476 P2 1.9 2.1 0.075 0.082 R 50 1.574 T 0.25 0.35 0.0098 0.0137 W 23.7 24.3 * on sales type 14/16 inch 0.933 0.956 inch MAX. MIN. MAX. 330 12.992 13.2 0.504 0.520 26.4 0.960 1.039 0.059 0795 3.937 30.4 1.197 BASE QTY BULK QTY 1000 1000 STB60NF06L - STP60NF06L - STP60NF06LFP 6 Revision history Revision history Table 6. Revision history Date Revision Changes 21-Jun-2004 2 Complete version 26-Jun-2006 3 New template, no content change 15/16 STB60NF06L - STP60NF06L - STP60NF06LFP Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 16/16