STTH10R04 High efficiency rectifier Features A ■ Ultrafast recovery ■ Low power losses ■ High surge capability ■ Low leakage current ■ K NC TO-220FPAC STTH10R04FP Description D2PAK STTH10R04G K K The STTH10R04 is an ultrafast recovery power rectifier dedicated to energy recovery in PDP application. A A NC K TO-220AC STTH10R04D It is especially designed for clamping function in energy recovery block. November 2007 A A K High junction temperature The compromise between forward voltage drop and recovery time offers optimized performances. K Table 1. Rev 1 DPAK STTH10R04B Device summary IF(peak) 10 A VRRM 400 V trr (typ) 15 ns Tj 175 °C VF (typ) 1.15 V 1/11 www.st.com 11 Characteristics STTH10R04 1 Characteristics Table 2. Absolute ratings (limiting values) Symbol Parameter Value Unit VRRM Repetitive peak reverse voltage 400 V IF(RMS) Forward current (rms) 20 A 10 A 100 A -65 to + 175 °C 175 °C DPAK, TO-220AC, D2PAK Tc = 135 °C δ = 0.5 Square signal TO-220FPAC Tc = 130 °C δ = 0.5 Square signal IFSM Surge non-repetitive forward current tp = 10 ms sinusoidal Tstg Storage temperature range IF(peak) Tj Table 3. Peak working forward current Maximum operating junction temperature Thermal parameters Symbol Parameter Value DPAK, TO-220AC, D2PAK Rth(j-c) Table 4. Symbol Unit 3.5 Junction to case °C/W TO-220FPAC 6 Static electrical characteristics Parameter IR (1) Reverse leakage current VF (2) Forward voltage drop Test conditions Tj = 25 °C Tj = 125 °C Tj = 25 °C Tj = 125 °C Min Typ Max Unit 10 VR = VRRM IF = 10 A µA 10 100 1.5 1.7 1.15 1.35 V 1. Pulse test: tp = 5 ms, δ < 2% 2. Pulse test: tp = 380 µs, δ < 2% To evaluate the conduction losses use the following equation: P = 1.05 x IF(AV) + 0.03 IF2(RMS) Table 5. Symbol Recovery characteristics Parameter trr Reverse recovery time tfr Forward recovery time VFP IRM Sfactor 2/11 Test conditions Tj = 25 °C IF = 0.5 A, Irr = 0.25 A, IR = 1 A Min Typ Max Unit 15 20 ns IF = 1 A, VR = 30 V, dIF/dt = -50 A/µs 40 Tj = 25 °C IF = 10 A, dIF/dt = 100 A/µs VFR = 1.1 x VFmax 140 ns Peak forward voltage Tj = 25 °C IF = 10 A , dIF/dt = 100 A/µs 3 V Reverse recovery current I = 10 A, VCC = 200 V Tj = 125 °C F dIF/dt = 200 A/µs 8 A Softness factor 6.2 0.3 STTH10R04 Characteristics Figure 1. Conduction losses versus average forward current Figure 2. P (W) 18 200 d=0.1 16 d=0.2 Forward voltage drop versus forward current IFM(A) d=1 d=0.5 180 d=0.05 Tj=125°C (Maximum values) 160 14 140 12 Tj=125°C (Typical values) 120 10 100 8 80 6 T 4 2 40 20 IF(av) (A) 0 VFM(V) 0 0 2 Figure 3. 4 6 8 10 12 0.0 0.5 Relative variation of thermal Figure 4. impedance junction to case versus pulse duration 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Relative variation of thermal impedance junction to case versus pulse duration Zth(j-c)/Rth(j-c) Zth(j-c)/Rth(j-c) 1.0 1.0 Single pulse D²PAK DPAK 0.9 0.8 Single pulse TO-220FPAC 0.9 0.8 0.7 0.7 0.6 0.6 0.5 0.5 0.4 0.4 0.3 0.3 0.2 0.2 0.1 0.1 tP(s) tP(s) 0.0 1.E-04 1.E-03 Figure 5. 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Tj=25°C (Maximum values) 60 1.E-02 1.E-01 1.E+00 Peak reverse recovery current versus dIF/dt (typical values) 0.0 1.E-03 1.E-02 Figure 6. IRM(A) 1.E+00 1.E+01 Reverse recovery time versus dIF/dt (typical values) trr(ns) 80 IF=IF(AV) VR=200V Tj=125°C 1.E-01 IF=IF(AV) VR=200V Tj=125°C 70 60 50 40 30 20 10 dIF/dt(A/µs) 0 dIF/dt(A/µs) 0 0 50 100 150 200 250 300 350 400 450 500 0 50 100 150 200 250 300 350 400 450 500 3/11 Characteristics Figure 7. STTH10R04 Reverse recovery charges versus dIF/dt (typical values) Figure 8. QRR(nC) S factor 0.8 300 IF=IF(AV) VR=200V Tj=125°C 250 Reverse recovery softness factor versus dIF/dt (typical values) IF < 2 x IF(AV) VR=200V Tj=125°C 0.7 0.6 200 0.5 0.4 150 0.3 100 0.2 50 0.1 dIF/dt(A/µs) 0 Figure 9. 50 100 150 200 250 300 350 400 450 0 500 Relative variations of dynamic parameters versus junction temperature 50 100 150 200 250 300 350 400 450 500 Figure 10. Transient peak forward voltage versus dIF/dt (typical values) VFP(V) 3.0 2.8 2.6 2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 12 IF=IF(AV) VR=200V Reference: Tj=125°C IF=IF(AV) Tj=125°C 11 10 SFACTOR 9 8 7 6 5 4 IRM 3 2 QRR 25 4/11 dIF/dt(A/µs) 0.0 0 50 Tj(°C) 75 100 dIF/dt(A/µs) 1 125 0 0 50 100 150 200 250 300 350 400 450 500 STTH10R04 Characteristics Figure 11. Forward recovery time versus dIF/dt (typical values) 200 Figure 12. Junction capacitance versus reverse voltage applied (typical values) C(pF) tfr(ns) 100 F=1MHz VOSC=30mVRMS Tj=25°C IF=IF(AV) VFR=1.1 x V F max. Tj=125°C 180 160 140 120 100 80 60 40 20 dIF/dt(A/µs) VR(V) 0 10 0 50 100 150 200 250 300 350 400 450 500 Figure 13. Thermal resistance, junction to ambient, versus copper surface under tab (epoxy printed board FR4, copper thickness = 35 µm) D2PAK 1 10 100 1000 Figure 14. Thermal resistance, junction to ambient, versus copper surface under tab (epoxy printed board FR4, copper thickness = 35 µm) DPAK Rth(j-a) (°C/W) Rth(j-a) (°C/W) 100 80 D²PAK DPAK 90 70 80 60 70 50 60 40 50 40 30 30 20 20 10 10 SCU(cm²) 0 5 10 15 20 SCU(cm²) 0 0 25 30 35 40 0 5 10 15 20 25 30 35 40 5/11 Package information 2 STTH10R04 Package information ● Epoxy meets UL94, V0 ● Cooling method: by conduction (C) ● Recommended torque calue: 0.8 N·m ● Maximum torque value: 1.0 N·m In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. Table 6. TO-220AC dimensions Dimensions Ref. Inches Min. Max. Min. Max. A 4.40 4.60 0.173 0.181 C 1.23 1.32 0.048 0.051 D 2.40 2.72 0.094 0.107 E 0.49 0.70 0.019 0.027 F 0.61 0.88 0.024 0.034 F1 1.14 1.70 0.044 0.066 G 4.95 5.15 0.194 0.202 H2 10.00 10.40 0.393 0.409 A H2 ØI C L5 L7 L6 L2 F1 Millimeters D L9 L2 L4 F M 16.40 typ. 0.645 typ. L4 13.00 14.00 0.511 0.551 L5 2.65 2.95 0.104 0.116 L6 15.25 15.75 0.600 0.620 L7 6.20 6.60 0.244 0.259 L9 3.50 3.93 0.137 0.154 E G M Diam. I 6/11 2.6 typ. 3.75 3.85 0.102 typ. 0.147 0.151 STTH10R04 Package information Table 7. TO-220FPAC dimensions Dimensions Ref. A Millimeters Inches Min. Max. Min. Max. A 4.4 4.6 0.173 0.181 B 2.5 2.7 0.098 0.106 D 2.5 2.75 0.098 0.108 E 0.45 0.70 0.018 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.70 0.045 0.067 G 4.95 5.20 0.195 0.205 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 B H Dia L6 L7 L2 L3 L5 F1 D L2 L4 F G1 G E 16 Typ. 0.63 Typ. L3 28.6 30.6 1.126 1.205 L4 9.8 10.6 0.386 0.417 L5 2.9 3.6 0.114 0.142 L6 15.9 16.4 0.626 0.646 L7 9.00 9.30 0.354 0.366 Dia. 3.00 3.20 0.118 0.126 7/11 Package information Table 8. STTH10R04 DPAK dimensions Dimensions Ref. E A B2 C2 L2 Millimeters Inches Min. Max. Min. Max. A 2.20 2.40 0.086 0.094 A1 0.90 1.10 0.035 0.043 A2 0.03 0.23 0.001 0.009 B 0.64 0.90 0.025 0.035 B2 5.20 5.40 0.204 0.212 C 0.45 0.60 0.017 0.023 C2 0.48 0.60 0.018 0.023 D 6.00 6.20 0.236 0.244 E 6.40 6.60 0.251 0.259 G 4.40 4.60 0.173 0.181 H 9.35 10.10 0.368 0.397 D R H L4 A1 B G R C A2 0.60 MIN. V2 L2 0.80 typ. L4 0.60 1.00 0.023 0.039 V2 0° 8° 0° 8° Figure 15. DPAK footprint (dimensions in mm) 6.7 3 3 1.6 2.3 6.7 2.3 1.6 8/11 0.031 typ. STTH10R04 Package information Table 9. D2PAK dimensions Dimensions Ref. A E C2 L2 D L L3 A1 B2 R C B G A2 M * V2 * FLAT ZONE NO LESS THAN 2mm Millimeters Inches Min. Max. Min. Max. A 4.40 4.60 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.70 0.93 0.027 0.037 B2 1.14 1.70 0.045 0.067 C 0.45 0.60 0.017 0.024 C2 1.23 1.36 0.048 0.054 D 8.95 9.35 0.352 0.368 E 10.00 10.40 0.393 0.409 G 4.88 5.28 0.192 0.208 L 15.00 15.85 0.590 0.624 L2 1.27 1.40 0.050 0.055 L3 1.40 1.75 0.055 0.069 M 2.40 3.20 0.094 0.126 R V2 0.40 typ. 0° 8° 0.016 typ. 0° 8° Figure 16. D2PAK footprint (dimensions in mm) 16.90 10.30 5.08 1.30 8.90 3.70 9/11 Ordering information 3 Ordering information Table 10. 4 Ordering information Order code Marking Package Weight Base qty Delivery mode STTH10R04FP STTH10R04FP TO-220FPAC 1.64 g 50 Tube STTH10R04B STTH10R04B 75 Tube DPAK 0.3g 2500 Tape and reel 50 Tube 1000 Tape and reel 50 Tube STTH10R04B-TR STTH10R04B STTH10R04G STTH10R04G STTH10R04G-TR STTH10R04G STTH10R04D STTH10R04D D2PAK TO-220AC 1.48 g 1.86 g Revision history Table 11. 10/11 STTH10R04 Document revision history Date Revision 07-Nov-2007 1 Description of changes First issue STTH10R04 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 11/11