STTH1202 Ultrafast recovery diode Main product characteristics IF(AV) 12 A VRRM 200 V Tj (max) 175° C VF (typ) 0.82 V trr (typ) 18 ns K Features and benefits ■ Very low conduction losses ■ Negligible switching losses ■ Low forward and reverse recovery time ■ High junction temperature ■ Insulated packages – TO-220FPAC Electrical insulation 1500 VRMS – TO-220AC Ins Electrical insulation 2500 VRMS K A A A K K TO-220AC STTH1202D TO-220FPAC STTH1202FP A K TO-220AC Ins STTH1202DI Description The STTH1202 uses ST's new 200V planar Pt doping technology, and is specially suited for switching mode base drive and transistor circuits. Packaged in TO-220AC, TO-220FPAC, and TO-220AC Ins, this device is intended for use in low voltage, high frequency inverters, free wheeling and polarity protection. March 2007 Order codes Rev 1 Part Number Marking STTH1202D STTH1202 STTH1202FP STTH1202 STTH1202DI STTH1202DI 1/10 www.st.com Characteristics STTH1202 1 Characteristics Table 1. Absolute ratings (limiting values at Tj = 25° C, unless otherwise specified) Symbol Parameter Value Unit VRRM Repetitive peak reverse voltage 200 VRSM Non repetitive peak reverse voltage 200 RMS forward current 30 A 12 A IF(RMS) IF(AV) V Average forward current, δ = 0.5 TO-220AC Tc = 140° C TO-220AC Ins Tc = 130° C TO-220FPAC Tc = 105° C IFRM Repetitive peak forward current tp = 10 µs F = 5 kHz square 130 A IFSM Surge non repetitive forward current tp = 10 ms Sinusoidal 100 A Tstg Storage temperature range -65 to + 175 °C 175 °C Value Unit Maximum operating junction temperature Tj Table 2. Thermal parameters Symbol Parameter TO-220AC Rth(j-c) Table 3. Symbol IR(1) Junction to case TO-220AC Ins 3 TO-220FPAC 5 Parameter Reverse leakage current Test conditions Tj = 25° C Tj = 125° C Tj = 150° C Forward voltage drop Min. Typ Max. Unit 10 VR = VRRM IF = 12 A µA 10 100 1.0 1.10 0.82 0.95 Tj = 25° C Tj = 125° C 1.15 IF = 15 A Tj = 150° C 1. Pulse test: tp = 5 ms, δ < 2 % 2. Pulse test: tp = 380 µs, δ < 2 % To evaluate the conduction losses use the following equation: P = 0.77 x IF(AV) + 0.015 x IF2(RMS) 2/10 ° C/W Static electrical characteristics Tj = 25° C VF(2) 2.5 0.91 1.05 0.87 1.0 V STTH1202 Characteristics Table 4. Dynamic characteristics Symbol Parameter trr Test conditions Typ Max. Unit IF = 1 A, dIF/dt = -50 A/µs, VR = 30 V, Tj = 25° C 28 35 ns IF = 1 A, dIF/dt = -100 A/µs, VR = 30 V, Tj = 25° C 18 24 Reverse recovery current IF = 12 A, dIF/dt = -200 A/µs, VR = 160 V, Tj = 125° C 5.8 7.5 Forward recovery time IF = 12 A, dIF/dt = 100 A/µs VFR = 1.1 x VFmax, Tj = 25° C 110 ns Forward recovery voltage IF = 12 A, dIF/dt = 100 A/µs, Tj = 25° C 2 V Reverse recovery time IRM tfr VFP Figure 1. Peak current versus duty cycle Figure 2. IM(A) Min. A Forward voltage drop versus forward current (typical values) IFM(A) 80 200 IM T 180 160 60 δ=tp/T Tj=150°C (maximum values) tp 140 120 P = 5W 40 80 P = 2W Tj=25°C (maximum values) 60 P = 1W 20 Tj=150°C (typical values) 100 40 δ 20 VFM(V) 0 0 0.0 0.1 Figure 3. 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 0.0 1.0 Relative variation of thermal impedance, junction to case, versus pulse duration (TO-220AC, TO-220AC Ins) 0.4 Figure 4. 0.8 1.2 1.6 2.0 2.4 2.8 Relative variation of thermal impedance, junction to case, versus pulse duration (TO-220FPAC) Zth(j-c)/Rth(j-c) Zth(j-c)/Rth(j-c) 1.0 1.0 Single pulse TO-220FPAC Single pulse TO-220AC TO-220AC Ins 0.1 tp(s) tp(s) 0.1 1.E-03 0.0 1.E-02 1.E-01 1.E+00 1.E-03 1.E-02 1.E-01 1.E+00 1.E+01 3/10 Characteristics Figure 5. STTH1202 Junction capacitance versus reverse applied voltage (typical values) Figure 6. C(pF) Reverse recovery charges versus dIF/dt (typical values) Qrr(nC) 200 100 F=1MHz VOSC=30mVRMS Tj=25°C VR=160V IF=12A 180 160 140 120 100 Tj=125°C Tj=25°C 80 60 40 20 VR(V) 10 dIF/dt(A/µs) 0 1 10 Figure 7. 100 1000 10 100 Reverse recovery time versus dIF/dt Figure 8. (typical values) trr(ns) 1000 Peak reverse recovery current versus dIF/dt (typical values) IRM(A) 100 14 VR=160V IF=12A VR=160V IF=12A 90 12 80 10 Tj=125°C 70 60 8 Tj=125°C 50 6 40 Tj=25°C 30 4 Tj=25°C 20 2 10 dIF/dt(A/µs) 0 100 Figure 9. 1000 Dynamic parameters versus junction temperature Qrr;IRM [Tj]/IRM [Tj=125°C] 1.4 VR=160V IF=12A 1.2 1.0 IRM 0.8 QRR 0.6 0.4 0.2 Tj(°C) 0.0 25 4/10 dIF/dt(A/µs) 0 10 50 75 100 125 150 10 100 1000 STTH1202 2 Ordering information scheme Ordering information scheme STTH 12 02 XX Ultrafast switching diode Average forward current 12 = 12 A Repetitive peak reverse voltage 02 = 200 V Package D = TO-220AC FP = TO-220FPAC DI = TO-220AC Ins 5/10 Package information 3 STTH1202 Package information ● Epoxy meets UL94, V0 ● Cooling method: by conduction (C) ● Recommended torque value: 0.55 Nm ● Maximum torque value: 0.7 Nm Table 5. T0-220AC dimensions DIMENSIONS REF. A H2 ØI C L5 L7 L6 L2 F1 Millimeters Inches Min. Max. Min. Max. A 4.40 4.60 0.173 0.181 C 1.23 1.32 0.048 0.051 D 2.40 2.72 0.094 0.107 E 0.49 0.70 0.019 0.027 F 0.61 0.88 0.024 0.034 F1 1.14 1.70 0.044 0.066 G 4.95 5.15 0.194 0.202 H2 10.00 10.40 0.393 0.409 D L9 L4 L2 F M E 16.40 typ. 0.645 typ. L4 13.00 14.00 0.511 0.551 L5 2.65 2.95 0.104 0.116 L6 15.25 15.75 0.600 0.620 L7 6.20 6.60 0.244 0.259 L9 3.50 3.93 0.137 0.154 G M Diam. I 6/10 2.6 typ. 3.75 3.85 0.102 typ. 0.147 0.151 STTH1202 Package information Table 6. T0-220FPAC dimensions DIMENSIONS REF A Millimeters Inches Min. Max. Min. Max. A 4.4 4.6 0.173 0.181 B 2.5 2.7 0.098 0.106 D 2.5 2.75 0.098 0.108 E 0.45 0.70 0.018 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.70 0.045 0.067 G 4.95 5.20 0.195 0.205 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 B H Dia L6 L2 L7 L3 L5 F1 D L4 L2 F G1 G E 16 Typ. 0.63 Typ. L3 28.6 30.6 1.126 1.205 L4 9.8 10.6 0.386 0.417 L5 2.9 3.6 0.114 0.142 L6 15.9 16.4 0.626 0.646 L7 9.00 9.30 0.354 0.366 Dia. 3.00 3.20 0.118 0.126 7/10 Package information Table 7. STTH1202 TO-220AC Ins. dimensions Dimensions Ref. Millimeters Min. A ØI 15.20 a1 C B b2 L Typ. Max. Inches Min. Typ. 15.90 0.598 3.75 Max. 0.625 0.147 a2 13.00 14.00 0.511 0.551 B 10.00 10.40 0.393 0.409 b1 0.61 0.88 0.024 0.034 b2 1.23 1.32 0.048 0.051 C 4.40 4.60 0.173 0.181 c1 0.49 0.70 0.019 0.027 c2 2.40 2.72 0.094 0.107 e 4.80 5.40 0.189 0.212 F 6.20 6.60 0.244 0.259 ØI 3.75 3.85 0.147 0.151 I4 15.80 16.40 16.80 0.622 0.646 0.661 L 2.65 2.95 0.104 0.116 l2 1.14 1.70 0.044 0.066 F A I4 c2 a1 l2 a2 M b1 e c1 M 2.60 0.102 In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 8/10 STTH1202 4 5 Ordering information Ordering information Part Number Marking Package Weight Base qty Delivery mode STTH1202D STTH1202 TO-220AC 1.86 g 50 Tube STTH1202FP STTH1202 TO-220FPAC 1.64 g 50 Tube STTH1202DI STTH1202DI TO-220AC Ins 2.3 g 50 Tube Revision history Date Revision 01-Mar-2007 1 Description of Changes First issue. 9/10 STTH1202 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 10/10