STMICROELECTRONICS STTH8R04D

STTH8R04
Ultrafast recovery diode
Main product characteristics
IF(AV)
8A
VRRM
400 V
Tj (max)
175° C
VF (typ)
0.9 V
trr (typ)
25 ns
A
K
K
■
Very low switching losses
■
High frequency and high pulsed current
operation
■
High junction temperature
TO-220FPAC
STTH8R04FP
A
A
NC
K
2
D PAK
STTH8R04G
TO-220AC Ins
STTH8R04DI
Order codes
The STTH8R04 series uses ST's new 400 V
planar Pt doping technology. The STTH8R04 is
specially suited for switching mode base drive and
transistor circuits.
Packaged in through-the-hole and surface mount
packages, this device is intended for use in low
voltage, high frequency inverters, free wheeling
and polarity protection.
March 2007
K
K
Insulated packages
– TO-220AC Ins
Electrical insulation = 2500 V RMS
Capacitance = 7 pF
– TO-220FPAC
Electrical insulation = 1500 V RMS
Capacitance = 12 pF
Description
A
A
TO-220AC
STTH8R04D
Features and benefits
■
K
Rev 1
Part Number
Marking
STTH8R04D
STTH8R04D
STTH8R04DI
STTH8R04DI
STTH8R04FP
STTH8R04FP
STTH8R04G
STTH8R04G
STTH8R04G-TR
STTH8R04G
1/11
www.st.com
Characteristics
STTH8R04
1
Characteristics
Table 1.
Absolute ratings (limiting values at 25° C, unless otherwise specified)
Symbol
Parameter
VRRM
Repetitive peak reverse voltage
VRSM
Repetitive peak reverse voltage
TO-220AC /
IF(RMS)
Unit
400
V
400
V
PAK / TO220FPAC
30
RMS forward current
A
TO220AC Ins
Average forward current, δ = 0.5
IF(AV)
D2
Value
20
TO-220AC / D2PAK
Tc = 145° C
TO220FPAC
Tc = 110° C
TO220AC Ins
Tc = 115° C
8
A
165
A
120
A
IFRM
Repetitive peak forward current
IFSM
Surge non repetitive forward current tp = 10 ms Sinusoidal
Tstg
Storage temperature range
-65 to +175
°C
Operating junction temperature range
-40 to +175
°C
Tj
Table 2.
tp = 10 µs, F = 1 kHz
Thermal parameters
Symbol
Parameter
Value
TO-220AC / D2PAK
Rth(j-c)
Table 3.
Symbol
IR(1)
Junction to case
2.5
TO220FPAC
6
TO220AB Ins
5.5
VF
Parameter
Reverse leakage current
Test conditions
Tj = 25° C
Tj = 125° C
Min.
Typ
Forward voltage drop
Tj = 100° C
Max.
Unit
10
VR = VRRM
µA
10
100
1.5
IF = 8 A
Tj = 150° C
1. Pulse test: tp = 5 ms, δ < 2 %
2. Pulse test: tp = 380 µs, δ < 2 %
To evaluate the conduction losses use the following equation:
P = 0.83 x IF(AV) + 0.034 x IF2(RMS)
2/11
°C/W
Static electrical characteristics
Tj = 25° C
(2)
Unit
1.05
1.3
0.9
1.1
V
STTH8R04
Table 4.
Characteristics
Dynamic characteristics
Symbol
Test conditions
Typ
Max
IF = 1 A, dIF/dt = -50 A/µs,
VR = 30 V, Tj = 25° C
35
50
IF = 1 A, dIF/dt = -100 A/µs,
VR = 30 V, Tj = 25° C
25
35
Reverse recovery current
IF = 8 A, dIF/dt = -200 A/µs,
VR = 320 V, Tj = 125° C
5.5
8
A
S
Softness factor
IF = 8 A, dIF/dt = -200 A/µs,
VR = 320 V, Tj = 125° C
0.4
tfr
Forward recovery time
IF = 8 A, dIF/dt = 100 A/µs
VFR = 1.1 x VFmax, Tj = 25° C
150
ns
Forward recovery voltage
IF = 8 A, dIF/dt = 100 A/µs
trr
Parameter
Reverse recovery time
IRM
VFP
Figure 1.
Conduction losses versus
average current
Figure 2.
P(W)
200
13
12
δ=0.05
δ=0.1
δ=0.5
δ=0.2
δ=1
Min
Unit
ns
2.9
V
Forward voltage drop versus
forward current
IFM(A)
180
11
TJ=150°C
(Maximum values)
160
10
9
140
8
120
7
TJ=150°C
(Typical values)
100
6
80
5
4
60
T
3
40
2
δ=tp/T
IF(AV)(A)
1
TJ=25°C
(Maximum values)
20
tp
0
VFM(V)
0
0
1
Figure 3.
2
3
4
5
6
7
8
9
10
11
Relative variation of thermal
impedance junction to case
versus pulse duration
0.0
0.4
Figure 4.
0.8
1.2
1.6
2.0
2.4
2.8
3.2
3.6
4.0
Relative variation of thermal
impedance junction to case versus
pulse duration TO-220FPAB
Zth(j-c)/Rth(j-c)
Zth(j-c)/Rth(j-c)
1.0
1.0
Single pulse
TO-220FPAB
Single pulse
TO-220AC
TO-220AC Ins
D²PAK
0.1
tp(s)
0.1
1.E-03
1.E-02
tp(s)
1.E-01
1.E+00
0.0
1.E-03
1.E-02
1.E-01
1.E+00
1.E+01
3/11
Characteristics
Figure 5.
STTH8R04
Peak reverse recovery current
versus dIF/dt (typical values)
Figure 6.
IRM(A)
12
11
tRR(ns)
140
IF= 8 A
VR=320 V
Reverse recovery time versus
dIF/dt (typical values)
IF= 8 A
VR=320 V
120
10
9
100
8
7
80
6
Tj=125 °C
5
4
3
60
Tj=125 °C
40
Tj=25 °C
Tj=25 °C
2
20
1
dIF/dt(A/µs)
dIF/dt(A/µs)
0
0
10
100
Figure 7.
200
1000
Reverse recovery charges versus
dIF/dt (typical values)
100
Figure 8.
1000
Thermal resistance junction to
ambient versus copper surface
under tab (Epoxy printed circuit
board FR4, eCU=35µm)
Rth(j-a) (°C/W)
QRR(nC)
80
D²PAK
IF= 8 A
VR=320 V
180
10
70
160
60
140
Tj=125 °C
120
50
100
40
80
30
60
20
Tj=25 °C
40
10
20
0
10
4/11
SCU(cm²)
dIF/dt(A/µs)
0
100
1000
0
2
4
6
8
10
12
14
16
18
20
STTH8R04
Figure 9.
Characteristics
Relative variations of dynamic
parameters versus junction
temperature
Figure 10. Transient peak forward voltage
versus dIF/dt (typical values)
QRR [Tj]/QRR [Tj = 125° C] and IRM [Tj]/IRM [Tj = 125° C]
1.4
5.0
IF= 8 A
VR=320 V
1.2
VFp(V)
IF=8 A
Tj=125 °C
4.5
4.0
1.0
3.5
3.0
IRM
0.8
2.5
0.6
2.0
QRR
1.5
0.4
1.0
0.2
0.5
T j(°C)
dIF/dt(A/µs)
0.0
0.0
25
50
75
100
125
0
150
50
100
150
200
250
300
350
400
450
500
Figure 11. Forward recovery time versus dIF/dt Figure 12. Junction capacitance versus
(typical values)
reverse voltage applied (typical
values)
700
tFR(ns)
C(pF)
100
IF=8 A
VFR=1.1 x V F max.
Tj=125°C
600
F=1MHz
VOSC=30mVRMS
Tj=25°C
500
400
300
200
100
dIF/dt(A/µs)
VR(V)
10
0
0
100
200
300
400
500
1
10
100
1000
5/11
Package information
2
STTH8R04
Package information
●
Epoxy meets UL94, V0
●
Cooling method: by conduction (C)
●
Recommended torque value: 0.55 Nm (TO-220AC, TO-220AC Ins, TO-220FPAC)
●
Maximum torque value: 0.70 Nm (TO-220AC, TO-220AC Ins, TO-220FPAC)
Table 5.
D2PAK dimensions
Dimensions
Ref.
A
E
C2
L2
D
L
L3
A1
B2
R
C
B
G
A2
M
*
V2
* FLAT ZONE NO LESS THAN 2mm
Millimeters
Min.
Max.
Min.
Max.
A
4.40
4.60
0.173
0.181
A1
2.49
2.69
0.098
0.106
A2
0.03
0.23
0.001
0.009
B
0.70
0.93
0.027
0.037
B2
1.14
1.70
0.045
0.067
C
0.45
0.60
0.017
0.024
C2
1.23
1.36
0.048
0.054
D
8.95
9.35
0.352
0.368
E
10.00
10.40
0.393
0.409
G
4.88
5.28
0.192
0.208
L
15.00
15.85
0.590
0.624
L2
1.27
1.40
0.050
0.055
L3
1.40
1.75
0.055
0.069
M
2.40
3.20
0.094
0.126
R
V2
0.40 typ.
0°
16.90
10.30
5.08
1.30
6/11
3.70
0.016 typ.
8°
Figure 13. D2PAK footprint (dimensions in mm)
8.90
Inches
0°
8°
STTH8R04
Package information
Table 6.
TO-220AC dimensions
Dimensions
Ref.
A
H2
ØI
C
L5
L7
L6
L2
F1
D
L9
F
M
E
G
Inches
Min.
Max.
Min.
Max.
A
4.40
4.60
0.173
0.181
C
1.23
1.32
0.048
0.051
D
2.40
2.72
0.094
0.107
E
0.49
0.70
0.019
0.027
F
0.61
0.88
0.024
0.034
F1
1.14
1.70
0.044
0.066
G
4.95
5.15
0.194
0.202
H2
10.00
10.40
0.393
0.409
L2
L4
Millimeters
16.40 typ.
0.645 typ.
L4
13.00
14.00
0.511
0.551
L5
2.65
2.95
0.104
0.116
L6
15.25
15.75
0.600
0.620
L7
6.20
6.60
0.244
0.259
L9
3.50
3.93
0.137
0.154
M
Diam.
I
2.6 typ.
3.75
3.85
0.102 typ.
0.147
0.151
7/11
Package information
Table 7.
STTH8R04
TO-220FPAC dimensions
Dimensions
Ref.
A
Millimeters
Inches
Min.
Max.
Min.
Max.
A
4.4
4.6
0.173
0.181
B
2.5
2.7
0.098
0.106
D
2.5
2.75
0.098
0.108
E
0.45
0.70
0.018
0.027
F
0.75
1
0.030
0.039
F1
1.15
1.70
0.045
0.067
G
4.95
5.20
0.195
0.205
G1
2.4
2.7
0.094
0.106
H
10
10.4
0.393
0.409
B
H
Dia
L6
L7
L2
L3
L5
F1
D
L2
L4
F
G1
G
8/11
E
16 Typ.
0.63 Typ.
L3
28.6
30.6
1.126
1.205
L4
9.8
10.6
0.386
0.417
L5
2.9
3.6
0.114
0.142
L6
15.9
16.4
0.626
0.646
L7
9.00
9.30
0.354
0.366
Dia.
3.00
3.20
0.118
0.126
STTH8R04
Package information
Table 8.
TO-220AC Ins. dimensions
Dimensions
Ref.
Millimeters
Min.
A
ØI
15.20
a1
C
B
b2
L
Typ.
Max.
Inches
Min.
Typ.
15.90 0.598
3.75
Max.
0.625
0.147
a2
13.00
14.00 0.511
0.551
B
10.00
10.40 0.393
0.409
b1
0.61
0.88
0.024
0.034
b2
1.23
1.32
0.048
0.051
C
4.40
4.60
0.173
0.181
c1
0.49
0.70
0.019
0.027
c2
2.40
2.72
0.094
0.107
e
4.80
5.40
0.189
0.212
F
6.20
6.60
0.244
0.259
ØI
3.75
3.85
0.147
0.151
I4
15.80 16.40 16.80 0.622 0.646 0.661
L
2.65
2.95
0.104
0.116
l2
1.14
1.70
0.044
0.066
F
A
I4
c2
a1
l2
a2
M
b1
e
c1
M
2.60
0.102
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a lead-free second level interconnect. The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com.
9/11
Ordering information
3
Ordering information
Part Number
Marking
Package
Weight
Base qty
Delivery mode
STTH8R04D
STTH8R04D
TO-220AC
1.86 g
50
Tube
STTH8R04DI
STTH8R04DI
TO-220 Ins
2.3 g
50
Tube
STTH8R04FP
STTH8R04FP
TO220FPAC
1.64 g
50
Tube
PAK
1.48 g
50
Tube
D PAK
1.48 g
1000
Tape and reel
STTH8R04G
STTH8R04G-TR
4
10/11
STTH8R04
STTH8R04G
D2
STTH8R04G
2
Revision history
Date
Revision
11-Mar-2007
1
Description of Changes
First issue.
STTH8R04
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2007 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
11/11