TD62783,784APG/AFG TOSHIBA Bipolar Digital Integrated Circuit Silicon Monolithic TD62783APG,TD62783AFG,TD62784APG,TD62784AFG 8 ch High-Voltage Source Driver The TD62783APG/AFG Series are comprised of eight source current Transistor Array. These drivers are specifically designed for fluorescent display applications. Applications include relay, hammer and lamp drivers. The suffix (G) appended to the part number represents a Lead (Pb)-Free product. TD62783APG TD62784APG Features • High output voltage: VCC = 50 V (min) • Output current (single output): IOUT = −500 mA (min) • Output clamp diodes • Single supply voltage • Input compatible with various types of logic • Package type-APG: DIP-18 pin • Package type-AFG: SOP-18 pin Type Designation TD62783APG/AFG TTL, 5V CMOS TD62784APG/AFG 6 to 15V PMOS, CMOS TD62783AFG TD62784AFG Weight DIP18-P-300-2.54D: 1.47 g (typ.) SOP18-P-375-1.27: 0.41 g (typ.) Pin Assignment (top view) O1 O2 O3 O4 O5 O6 O7 O8 GND 18 17 16 15 14 13 12 11 10 1 I1 2 I2 3 I3 4 I4 5 I5 6 I6 7 I7 8 I8 9 VCC 1 2006-06-14 TD62783,784APG/AFG Schematics (each driver) 20 kΩ VCC 2.6 kΩ 10 kΩ 10 kΩ Input n Output 5 kΩ TD62783: n = 1 TD62784: n = 4 GND Note: The input and output parasitic diodes cannot be used as clamp diodes. Absolute Maximum Ratings (Ta = 25°C) Characteristics Symbol Rating Unit Supply voltage VCC 50 V Output current IOUT −500 mA/ch Input voltage Clamp diode reverse voltage 15 30 VR Clamp diode forward current Power dissipation VIN (Note 1) VIN (Note 2) IF APG AFG PD (Note 3) V 50 V 500 mA 1.47 W 0.96 Operating temperature Topr −40 to 85 °C Storage temperature Tstg −55 to 150 °C Note 1: Only TD62783APG/AFG Note 2: Only TD62784APG/AFG Note 3: Derated above 25°C in the proportion of 11.7 W/°C (APG type), 7.7 W/°C (AFG type) 2 2006-06-14 TD62783,784APG/AFG Recommended Operating Conditions (Ta = −40 to 80°C) Characteristics Symbol Test Condition Min Typ. Max Unit VCC ⎯ ⎯ ⎯ 50 V Duty = 10% 8 circuits ⎯ ⎯ −260 Supply voltage Output current Ta = 85°C, Tj = 120°C, Tpw = 25 ms IOUT AFG TD62783APG/AFG Input voltage VIN TD62784APG/AFG Input voltage Duty = 50% 8 circuits ⎯ ⎯ −59 Duty = 10% 8 circuits ⎯ ⎯ −180 Duty = 50% 8 circuits ⎯ ⎯ −38 ⎯ ⎯ ⎯ 12 ⎯ ⎯ ⎯ 24 15 mA/ch V Output TD62783APG/AFG ON TD62784APG/AFG VIN (ON) ⎯ 2.0 5.0 ⎯ 4.5 12.0 30 Output TD62783APG/AFG OFF TD62784APG/AFG VIN (OFF) ⎯ 0 ⎯ 0.8 ⎯ 0 ⎯ 2.0 ⎯ ⎯ ⎯ 50 ⎯ ⎯ ⎯ 35 ⎯ ⎯ ⎯ 400 ⎯ ⎯ ⎯ 0.52 ⎯ ⎯ ⎯ 0.35 Min Typ. Max Unit VCC = VCC max VIN = 0.4 V Ta = 25°C ⎯ ⎯ 100 µA VIN = VIN (ON), IOUT = −350 mA ⎯ ⎯ 2.0 VIN = VIN (ON), IOUT = −225 mA ⎯ ⎯ 1.9 VIN = VIN (ON), IOUT = −100 mA ⎯ ⎯ 1.8 VIN = 2.4 V ⎯ 36 52 VIN = 3.85 V ⎯ 180 260 VIN = 5 V ⎯ 92 130 VIN = 12 V ⎯ 790 1130 VCE = 2.0 V ⎯ ⎯ 2.0 Clamp diode reverse voltage APG VR AFG Clamp diode forward current Power dissipation IF APG PD AFG V V mA W Electrical Characteristics (Ta = 25°C) Characteristics Output leakage current Output saturation voltage Symbol Test Circuit ICEX 1 VCE (sat) 2 TD62783APG/AFG Input current IIN (ON) 3 TD62784APG/AFG TD62783APG/AFG TD62784APG/AFG VIN (ON) Input voltage 4 TD62783APG/AFG TD62784APG/AFG Test Condition IOUT = −350 mA IOUT = −500 µA VIN (OFF) ⎯ ⎯ 4.5 0.8 ⎯ ⎯ 2.0 ⎯ ⎯ V µA V ICC (ON) 3 VIN = VIN (ON), VCC = 50 V ⎯ ⎯ 2.5 mA/ch Clamp diode reverse current IR 5 VR = 50 V ⎯ ⎯ 50 µA Clamp diode forward voltage VF 6 IF = 350 mA ⎯ ⎯ 2.0 V Turn-ON delay tON 7 VCC = VCC max RL = 125 Ω CL = 15 pF, RL = 88 Ω ⎯ 0.15 ⎯ µs Turn-OFF delay tOFF 7 VCC = VCC max RL = 125 Ω CL = 15 pF, RL = 88 Ω ⎯ 1.8 ⎯ µs Supply current 3 2006-06-14 TD62783,784APG/AFG Test Circuit 1. ICEX 2. VCE (sat) VCC 3. IIN (ON), ICC VCC VCC VCE (sat) VIN IOUT VIN ICEX 4. VIN (ON), VIN (OFF) IIN (ON) VIN 5. IR VCC 6. VF VCC Open VCE VIN (ON), VIN (OFF) IR VR IOUT VF IF 7. tON, tOFF Input VIH VCC Input 0 Pulse generator (Note 1) 50% 50% 50 µs VIN RL tON CL (Note 2) tOFF VOH Output 50% 50% VOL Note 1: Pulse Width 50 µs, Duty Cycle 10% Output Impedance 50 Ω, tr ≤ 5 ns, tf ≤ 10 ns Note 2: CL includes probe and jig capacitance. Precautions for Using This IC does not integrate protection circuits such as overcurrent and overvoltage protectors. Thus, if excess current or voltage is applied to the IC, the IC may be damaged. Please design the IC so that excess current or voltage will not be applied to the IC. Utmost care is necessary in the design of the output line, VCC and GND line since IC may be destroyed due to short-circuit between outputs, air contamination fault, or fault by improper grounding. 4 2006-06-14 TD62783,784APG/AFG IOUT – VIN IOUT – VIN 500 500 TA62783APG/AFG TA62784APG/AFG Ta = 25°C (mA) 400 Output current IOUT Output current IOUT (mA) Ta = 25°C typ. 300 200 100 0 0 0.4 0.8 1.2 Input voltage 1.6 400 300 200 100 0 0 2.0 1 2 VIN (V) Input voltage IIN – VIN VIN (V) Ta = 25°C typ. (mA) TA62784APG/AFG Ta = 25°C typ. 1.2 2.4 IIN (mA) TA62783APG/AFG IIN 0.8 Input current Input current 5 3.2 0.4 0 0 4 8 Input voltage 12 1.6 0.8 0 0 16 VIN (V) 8 16 Input voltage IOUT – VCE (sat) 0.6 24 32 VIN (V) IF – VF 0.6 Ta = 25°C Ta = 25°C typ. IF (A) (A) |VCC − VEE| > 5 V 0.4 Diode forward current IOUT 4 IIN – VIN 1.6 Output current 3 0.2 0 0 0.8 1.6 Output saturation voltage 2.4 0.4 0.2 0 0 3.2 VCE (sat) (V) 0.4 0.8 Diode forward voltage 5 1.2 VF 1.6 (V) 2006-06-14 TD62783,784APG/AFG PD – Ta PD (W) 2.0 (1) Type-APG free air (2) Type-AFG free air 1.5 Power dissipation (1) 1.0 (2) 0.5 0 0 500 100 Ambient temperature 150 Ta 200 (°C) 6 2006-06-14 TD62783,784APG/AFG Package Dimensions Weight: 1.47 g (typ.) 7 2006-06-14 TD62783,784APG/AFG Package Dimensions Weight: 0.41 g (typ.) 8 2006-06-14 TD62783,784APG/AFG Notes on Contents 1. Equivalent Circuits The equivalent circuit diagrams may be simplified or some parts of them may be omitted for explanatory purposes. 2. Test Circuits Components in the test circuits are used only to obtain and confirm the device characteristics. These components and circuits are not guaranteed to prevent malfunction or failure from occurring in the application equipment. IC Usage Considerations Notes on Handling of ICs (1) The absolute maximum ratings of a semiconductor device are a set of ratings that must not be exceeded, even for a moment. Do not exceed any of these ratings. Exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. (2) Use an appropriate power supply fuse to ensure that a large current does not continuously flow in case of over current and/or IC failure. The IC will fully break down when used under conditions that exceed its absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs from the wiring or load, causing a large current to continuously flow and the breakdown can lead smoke or ignition. To minimize the effects of the flow of a large current in case of breakdown, appropriate settings, such as fuse capacity, fusing time and insertion circuit location, are required. (3) If your design includes an inductive load such as a motor coil, incorporate a protection circuit into the design to prevent device malfunction or breakdown caused by the current resulting from the inrush current at power ON or the negative current resulting from the back electromotive force at power OFF. IC breakdown may cause injury, smoke or ignition. Use a stable power supply with ICs with built-in protection functions. If the power supply is unstable, the protection function may not operate, causing IC breakdown. IC breakdown may cause injury, smoke or ignition. (4) Do not insert devices in the wrong orientation or incorrectly. Make sure that the positive and negative terminals of power supplies are connected properly. Otherwise, the current or power consumption may exceed the absolute maximum rating, and exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. In addition, do not use any device that is applied the current with inserting in the wrong orientation or incorrectly even just one time. (5) Carefully select external components (such as inputs and negative feedback capacitors) and load components (such as speakers), for example, power amp and regulator. If there is a large amount of leakage current such as input or negative feedback condenser, the IC output DC voltage will increase. If this output voltage is connected to a speaker with low input withstand voltage, overcurrent or IC failure can cause smoke or ignition. (The over current can cause smoke or ignition from the IC itself.) In particular, please pay attention when using a Bridge Tied Load (BTL) connection type IC that inputs output DC voltage to a speaker directly. 9 2006-06-14 TD62783,784APG/AFG Points to Remember on Handling of ICs (1) Heat Radiation Design In using an IC with large current flow such as power amp, regulator or driver, please design the device so that heat is appropriately radiated, not to exceed the specified junction temperature (Tj) at any time and condition. These ICs generate heat even during normal use. An inadequate IC heat radiation design can lead to decrease in IC life, deterioration of IC characteristics or IC breakdown. In addition, please design the device taking into considerate the effect of IC heat radiation with peripheral components. (2) Back-EMF When a motor rotates in the reverse direction, stops or slows down abruptly, a current flow back to the motor’s power supply due to the effect of back-EMF. If the current sink capability of the power supply is small, the device’s motor power supply and output pins might be exposed to conditions beyond absolute maximum ratings. To avoid this problem, take the effect of back-EMF into consideration in system design. 10 2006-06-14 TD62783,784APG/AFG About solderability, following conditions were confirmed • Solderability (1) Use of Sn-37Pb solder Bath · solder bath temperature = 230°C · dipping time = 5 seconds · the number of times = once · use of R-type flux (2) Use of Sn-3.0Ag-0.5Cu solder Bath · solder bath temperature = 245°C · dipping time = 5 seconds · the number of times = once · use of R-type flux RESTRICTIONS ON PRODUCT USE 060116EBA • The information contained herein is subject to change without notice. 021023_D • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. 021023_A • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer’s own risk. 021023_B • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. 060106_Q • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. 021023_C • The products described in this document are subject to the foreign exchange and foreign trade laws. 021023_E 11 2006-06-14