2010 POWER INDUCTORS High Reliability Power Inductors MS338PWA ■ High temperature materials allow operation in ambient temperatures up to 155°C ■ Very low DCR and excellent current handling. ■ Soft saturation makes them ideal for VRM/VRD applications. ■ Tin-lead (Sn-Pb) termination for the best possible board adhesion ■ Special construction allows it to pass vibration testing to 30 G and shock testing to 500 G. Weight 20 mg Terminations Tin-lead (63/37) over tin over nickel over silver. Ambient temperature –55°C to +105°C with Irms current, +105°C to +155°C with derated current Storage temperature Component: –55°C to +155°C. Packaging: –55°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Enhanced crush-resistant packaging 1000/7″reel Plastic tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 1.19 mm pocket depth DCR (Ohms)3 SRF (MHz)4 Isat (A)5 Irms (A)6 Inductance2 1 Part number ±20% (µH) nom max min typ 10% drop 20% drop 30% drop 20°C rise 40°C rise MS338PWA201MSZ 0.20 0.0240.027 286 408 2.80 3.45 3.75 2.2 2.8 MS338PWA331MSZ 0.33 0.0310.035 216 309 1.90 2.75 3.05 1.9 2.6 MS338PWA501MSZ 0.50 0.0400.045 153 218 1.80 2.35 2.64 1.7 2.3 MS338PWA681MSZ 0.68 0.0570.063 106 152 1.55 1.95 2.19 1.5 2.1 MS338PWA821MSZ 0.82 0.0680.075 93 132 1.25 1.65 1.90 1.3 1.7 MS338PWA102MSZ 1.0 0.0810.089 82 117 1.20 1.60 1.80 1.1 1.6 MS338PWA152MSZ 1.5 0.1050.116 56 80 0.950 1.30 1.50 1.0 1.4 MS338PWA222MSZ 2.2 0.1560.173 53 75 0.940 1.20 1.35 0.96 1.3 MS338PWA332MSZ 3.3 0.2070.228 39 55 0.700 0.925 1.05 0.79 1.1 MS338PWA472MSZ 4.7 0.3360.370 28 40 0.580 0.750 0.845 0.74 1.0 MS338PWA682MSZ 6.8 0.4210.463 23 33 0.450 0.620 0.725 0.64 0.87 MS338PWA822MSZ 8.2 0.4570.503 21 30 0.440 0.600 0.670 0.55 0.75 MS338PWA103MSZ 10 0.5550.611 20 28 0.390 0.525 0.610 0.49 0.66 1. When ordering, please specify testing code: 2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc. 3. DCR measured on a micro-ohmmeter. 4. SRF measured using Agilent/HP 4395A or equivalent. 5. DC current at which the inductance drops the specified amount from its value without current. 6. Current that causes the specified temperature rise fron 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. MS338PWA224MSZ Testing:Z =COTS H =Screening per Coilcraft CP-SA-10001 N =Screening per Coilcraft CP-SA-10004 ® Specifications subject to change without notice. Please check our website for latest information. 1102 Silver Lake Road Cary IL 60013 © Coilcraft, Inc. 2012 Document MS646-1 Revised 06/28/12 Phone 800-981-0363 Fax 847-639-1508 E-mail [email protected] Web www.coilcraft-cps.com 2010 POWER INDUCTORS MS338PWA Series Typical L vs Current Typical L vs Frequency 100 10 µH 10 Inductance (µH) Inductance (µH) 100 3.3 µH 1.0 µH 1 10 µH 10 3.3 µH 1.0 µH 1 0.33 µH 0.33 µH 0.1 0.1 0.01 1 0.1 10 0.1 10 1 100 Frequency (MHz) Current (A) Irms Derating 0.079 ±0.008 2,0 ±0,2 120 110 90 0.075 ±0.008 1,9 ±0,2 80 70 60 0.039 max 1,00 50 40 25°C Percent of rated Irms 100 30 Recommended Suggested LandPattern Pattern Land 0.057 1,45 0.030 max 0,75 20 10 0 -55 -40 -20 0 20 40 60 80 100 120 140 160 Ambient temperature (°C) 0.069 max 1,75 0.014 min 0,35 Dimensions are in ® © Coilcraft, Inc. 2012 0.041 1,04 inches mm Specifications subject to change without notice. Please check our website for latest information. 1102 Silver Lake Road Cary IL 60013 0.087 2,2 Document MS646-2 Revised 06/28/12 Phone 800-981-0363 Fax 847-639-1508 E-mail [email protected] Web www.coilcraft-cps.com