Preliminary New relay, production not started, engineering samples available FTR-K1 SERIES POWER RELAY 1 POLE - 25A Latching Relay FTR-K3L Series n FEATURES 1 pole, 25A, 1 form A 2 coils latching type l High insulation (between coil and contacts) Insulation distance: clearance min. 6.4mm creepage min. 9.5mm Dielectric strength: 5,000VAC Surge strength: 8,500V l Cadmium free contact for eco-program l Plastic materials - UL 94 flame class V-0 l Flux proof, cat II l RoHS compliant Please see page 5 for more information l l n PARTNUMBER INFORMATION [Example] FTR-K3 (a) L A (b) (c) B 012 (d) (e) W (f) (a) Relay type FTR-K3: FTR-K3 Series (b) Operating function L : Latching type A J : 1 form A / PCB type : 1 form A / Tab type B : Standard sensitive (0.9W) (c) Contact configuration (d) Coil power (e) Coil rated voltage 012 (d) Contact material W : 5.....24VDC Coil rating table at page 3 : AgSnO2 Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-K3LAB012W Actual marking: K3LAB012W 1 Preliminary FTR-K1SERIES SERIES FTR-K3L n SPECIFICATION Item Contact Data Life Coil Data Timing Data Insulation FTR-K3L Configuration 1 form A Construction Single Material Silver tin oxide (AgSnO2) Resistance (initial) Max. 100 mOhm at 6VDC, 1A Contact rating (resistive) 25A, 250VAC Max. carrying current 30A Max. switching voltage 250VAC Max. switching power 6,250VA Max. switching current 25A Min. switching load * 100mA, 5VDC Mechanical Min. 1 x 106 operations Electrical 25A, 250VAC, min. 100 x 103 operations Rated power (at 20 °C) 900mW Operating temperature range -40 °C to +60 °C (no frost) Set (at nominal voltage) Max. 20ms (without bounce) Reset (at nominal voltage) Max. 20ms (without bounce) Coil excitation time (at nominal voltage) Min. 30ms Resistance (initial) Min. 1,000MOhm at 500VDC Dielectric strength Surge strength Other Between contacts 1,000VAC (50/60Hz) 1min Between coil to contacts 5,000VAC (50/60Hz) 1min Coil to contacts 8,500V / 1.2 x 50µs standard wave Clearance 6.4mm Creepage 9.5mm Vibration resistance Shock Misoperation>1us 10 to 55Hz double amplitude 1.5mm Endurance 10 to 55Hz double amplitude 1.5mm Misoperation>1us Min. 200m/s² (11 ± 1ms) Endurance Min. 1,000m/s² (6 ± 1ms) Weight Approximately 25 g Sealing Flux proof cat II * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental contions and expected reliability levels. 2 FTR-K1SERIES SERIES FTR-K3L Preliminary n COIL RATING Set/Reset Voltage Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Min. (VDC) * 005 5 28 4.0 9.0 012 12 160 9.6 21.6 024 24 640 19.2 43.2 Max. (VDC) * Rated Power (mW) 900 Note: All values in the tables are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 Flammability: UL 94-V0 (plastics) 25A, 277VAC VDE 0435 25A, 250VAC, 60ºC n COIL POLARITY See schematics at page 4. Coil terminal A B Set - + Reset + C - 3 Preliminary FTR-K1SERIES SERIES FTR-K3L n DIMENSIONS l External dimensions Type J Type A l Schematics Type J TOP VIEW Type A BOTTOM VIEW BOTTOM VIEW l PC board mounting hole layout (BOTTOM VIEW) Unit: mm 4 Preliminary FTR-K1SERIES SERIES FTR-K3L RoHS Compliance and Lead Free Information 1. General Information All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 5 Preliminary FTR-K1SERIES SERIES FTR-K3L Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] Web: http://www.fujitsu.com/sg/services/micro/components/ ©2010 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. December 07, 2010 6 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Fujitsu: FTR-K3LAB012W FTR-K3LAB024W FTR-K3LJB012W FTR-K3LJB024W