TI SN75109AN

SN55109A, SN55110A
SN75109A, SN75110A, SN75112
DUAL LINE DRIVERS
SLLS106B – DECEMBER 1975 – REVISED MAY 1995
•
•
•
•
•
•
•
•
•
Improved Stability Over Supply Voltage and
Temperature Ranges
Constant-Current Outputs
High Speed
Standard Supply Voltages
High Output Impedance
High Common-Mode Output Voltage Range
– 3 V to 10 V
TTL-Input Compatibility
Inhibitor Available for Driver Selection
Glitch-Free During Power Up/Power Down
SN75112 and External Circuit Meets or
Exceeds the Requirements of CCITT
Recommendation V.35
SN55109A, SN55110A . . . J OR W PACKAGE
SN75109A, SN75110A, SN75112 . . . D OR N PACKAGE
(TOP VIEW)
1A
1B
1C
2C
2A
2B
GND
1
14
2
13
3
12
4
11
5
10
6
9
7
8
VCC+
1Y
1Z
VCC –
D
2Z
2Y
SN55109A, SN55110A . . . FK PACKAGE
(TOP VIEW)
1B
1A
NC
VCC+
1Y
•
description
1C
NC
2C
NC
2A
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
1Z
NC
VCC –
NC
D
2B
GND
NC
2Y
2Z
The
SN55109A,
SN55110A,
SN75109A,
SN75110A, and SN75112 dual line drivers have
improved output current regulation with supply
voltage and temperature variations. In addition,
the higher current of the SN75112 (27 mA) allows
data to be transmitted over longer lines. These
drivers offer optimum performance when used
with the SN55107A, SN55108A, SN75107A, and
SN75108A line receivers.
4
NC – No internal connection
These drivers feature independent channels with
THE SN75109A IS NOT
RECOMMENDED FOR NEW DESIGNS
common voltage supply and ground terminals.
The significant difference between the three
drivers is in the output current specification. The driver circuits feature a constant output current that is switched
to either of two output terminals by the appropriate logic levels at the input terminals. The output current can
be switched off (inhibited) by low logic levels on the enable inputs. The output current is nominally 6 mA for the
’109A, 12 mA for the ’110A, and 27 mA for the SN75112.
The enable/inhibit feature is provided so the circuits can be used in party-line or data-bus applications. A strobe
or inhibitor (enable D), common to both drivers, is included for increased driver-logic versatility. The output
current in the inhibited mode, IO(off), is specified so that minimum line loading is induced when the driver is used
in a party-line system with other drivers. The output impedance of the driver in the inhibited mode is very high.
The output impedance of a transistor is biased to cutoff.
AVAILABLE OPTIONS
PACKAGED DEVICES
TA
0°C to 70°C
SMALL OUTLINE
(D)
CHIP CARRIER
(FK)
CERAMIC DIP
(J)
SN75109AD
SN75110AD
SN75112D
– 55°C
55 C to 125
125°C
C
CERAMIC
FLATPACK
(W)
PLASTIC DIP
(N)
SN75109AN
SN75110AN
SN75112N
SN55109AFK
SN55110AFK
SN55109AJ
SN55110AJ
SN55109AJ
SN55110AJ
SN55109AW
SN55110AW
The D package is available taped and reeled. Add the suffix R to the device type, (e.g., SN75110ADR).
Copyright  1995, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
2–1
SN55109A, SN55110A
SN75109A, SN75110A, SN75112
DUAL LINE DRIVERS
SLLS106B – DECEMBER 1975 – REVISED MAY 1995
description (continued)
The driver outputs have a common-mode voltage range of – 3 V to 10 V, allowing common-mode voltage on
the line without affecting driver performance.
All inputs are diode clamped and are designed to satisfy TTL-system requirements. The inputs are tested at
2 V for high-logic-level input conditions and 0.8 V for low-logic-level input conditions. These tests ensure
400-mV noise margin when interfaced with TTL Series 54/74.
The SN55109A and SN55110A are characterized for operation over the full military temperature range of – 55°C
to 125°C. The SN75109A, SN75110A, and SN75112 are characterized for operation from 0°C to 70°C.
FUNCTION TABLE
(each driver)
LOGIC
INPUTS
ENABLE
INPUTS
OUTPUTS†
C
D
Y
Z
A
B
X
X
L
X
Off
Off
X
X
X
L
Off
Off
L
X
H
H
On
Off
X
L
H
H
On
Off
H
H
H
H
Off
On
H = high level, L = low level, X = irrelevant
† When using only one channel of the line drivers, the other
channel should be inhibited and/or have its outputs
grounded.
2–2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN55109A, SN55110A
SN75109A, SN75110A, SN75112
DUAL LINE DRIVERS
SLLS106B – DECEMBER 1975 – REVISED MAY 1995
schematic (each driver)
VCC +
14
+
C
D
2.2 kΩ
NOM
3, 4
10
To Other
Driver
–
–
+
2.2 kΩ
NOM
8, 13
9, 12
Y
Z
A 1, 5
B 2, 6
7
GND
–
Common to Both Drivers
+
VCC – 11
–
+
... VCC + bus
–
–
... VCC – bus
To Other Driver
Pin numbers shown are for D, J, N, and W packages.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
2–3
SN55109A, SN55110A
SN75109A, SN75110A, SN75112
DUAL LINE DRIVERS
SLLS106B – DECEMBER 1975 – REVISED MAY 1995
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
SN55109A
SN55110A
Supply voltage, VCC + (see Note 1)
Supply voltage, VCC –
Input voltage, VI
SN75109A
SN75110A
UNIT
7
7
7
V
–7
–7
–7
V
5.5
V
5.5
Output voltage range, VO
SN75112
5.5
– 5 to 12
Continuous total power dissipation (see Note 2)
– 5 to 12
– 5 to 12
V
See Dissipation Rating Table
Operating free-air temperature range, TA
– 55 to 125
0 to 70
0 to 70
°C
Storage temperature range, Tstg
– 65 to 150
– 65 to 150
– 65 to 150
°C
Case temperature for 60 seconds: FK package
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds
J or W package
260
°C
300
°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
D or N package
260
260
°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. Voltage values are with respect to network ground terminal.
2. In the FK, J, or W package, SN55109A and SN55110A chips are either silver glass or alloy mounted, and SN75109A, SN75110A,
and SN75112 chips are glass mounted.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
D
950 mW
FK
J
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 125°C
POWER RATING
7.6 mW/°C
608 mW
—
1375 mW
11.0 mW/°C
880 mW
275 mW
1375 mW
11.0 mW/°C
880 mW
275 mW
N
1150 mW
9.2 mW/°C
736 mW
—
W
1000 mW
8.0 mW/°C
640 mW
200 mW
recommended operating conditions (see Note 3)
SN75109A
SN75110A
SN75112
SN55109A
SN55110A
UNIT
MIN
NOM
MAX
MIN
NOM
MAX
Supply voltage, VCC +
4.5
5
5.5
4.75
5
5.25
V
Supply voltage, VCC –
– 4.5
–5
–5
– 5.5
– 4.75
– 5.25
V
Positive common-mode output voltage
0
10
0
10
V
Negative common-mode output voltage
0
–3
0
–3
V
High-level input voltage, VIH
2
Low-level output current, VIL
2
V
0.8
V
Operating free-air temperature, TA
– 55
125
0
70
NOTE 3: When using only one channel of the line drivers, the other channel should be inhibited and/or have its outputs grounded.
°C
2–4
0.8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
TEST CONDITIONS†
PARAMETER
SN55109A
SN75109A
MIN
VIK
IO(
O(on))
IO(off)
VCC ± = MIN, IL = – 12 mA
VCC ± = MAX, VO = 10 V
Input clamp voltage
VCC = MIN to MAX,
VO = – 1 V to 1 V
V,
TA = 25°C
VCC ± = MIN, VO = – 3 V
On state output current
On-state
VCC ± = MIN,
Off-state output current
A, B, or C inputs
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
II
Input current at maximum
input voltage
IIH
High level input current
High-level
IIL
Low level input current
Low-level
ICC + (on)
Supply current from VCC + with driver enabled
ICC – (on)
( )
Supply current from VCC – with driver enabled
ICC + (off)
Supply current from VCC – with driver inhibited
D input
A, B, or C inputs
D input
A, B, or C inputs
D input
3.5
SN55110A
SN75110A
TYP‡
MAX
– 0.9
6
TYP‡
MAX
– 1.5
– 0.9
7
12
6
VO = 10 V
UNIT
TYP‡
MAX
– 1.5
– 0.9
– 1.5
15
27
36
24
28
32
mA
18
27
µA
12
MIN
100
100
100
1
1
1
2
2
2
40
40
40
80
80
80
–3
–3
–3
–6
–6
–6
VCC ± = MAX
MAX, VI = 2
2.4
4V
4V
VCC ± = MAX
MAX, VI = 0
0.4
VCC ± = MAX,
A, B, C, and D inputs at 0.4 V
MIN
6.5
VCC ± = MAX
MAX, VI = 5
5.5
5V
VCC ± = MAX,
A and B inputs
in uts at 0
0.4
4V
V,
C and D inputs at 2 V
SN75112
18
30
23
35
25
40
– 18
– 30
– 34
– 50
– 65
– 100
V
mA
µA
mA
mA
18
ICC – (off) Supply current from VCC ± with driver inhibited
– 10
† For conditions shown as MIN or MAX, use appropriate value specified under recommended operating conditions.
‡ All typical values are at VCC + = 5 V, VCC – = – 5 V, TA = 25°C.
21
30
– 17
– 32
mA
SN55109A, SN55110A
SN75109A, SN75110A, SN75112
DUAL LINE DRIVERS
SLLS106B – DECEMBR 1975 – REVISED MAY 1995
2–5
SN55109A, SN55110A
SN75109A, SN75110A, SN75112
DUAL LINE DRIVERS
SLLS106B – DECEMBER 1975 – REVISED MAY 1995
switching characteristics, VCC± = ±5 V, TA = 25°C
PARAMETER †
FROM
(INPUT)
TO
(OUTPUT)
A or B
Y or Z
tPLH
tPHL
TEST CONDITIONS
RL = 50 Ω
Ω,
CL = 40 pF,
pF
tPLH
tPHL
C or D
MIN
See Figure 1
Y or Z
TYP
MAX
UNIT
9
15
ns
9
15
ns
16
25
ns
13
25
ns
† tPLH = Propagation delay time, low-to-high-level output
tPHL = Propagation delay time, high-to-low-level output
PARAMETER MEASUREMENT INFORMATION
VCC +
Input A or B
VCC –
890 Ω
50 Ω
RL = 50 Ω
Output Y
890 Ω
CL = 40 pF
(see Note B)
Pulse
Generator
See Note A
Output Z
Pulse
Generator
RL = 50 Ω
CL = 40 pF
(see Note B)
To Other Driver
Input C or D
50 Ω
See Note C
TEST CIRCUIT
3V
50%
50%
Input A or B
0V
t w1
t w2
Enable C or D
3V
50%
50%
0V
t PHL
t PLH
50%
t PHL
t PLH
50%
off
50%
Output Y
50%
on
t PHL
t PLH
Output Z
50%
off
50%
on
VOLTAGE WAVEFORMS
NOTES: A. The pulse generators have the following characteristics: ZO = 50 Ω, tr = tf = 10 ± 5 ns, tw1 = 500 ns, PRR ≤ 1 MHz, tw2 = 1 µs,
PRR ≤ 500 kHz.
B. CL includes probe and jig capacitance.
C. For simplicity, only one channel and the enable connections are shown.
Figure 1. Test Circuit and Voltage Waveforms
2–6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN55109A, SN55110A
SN75109A, SN75110A, SN75112
DUAL LINE DRIVERS
SLLS106B – DECEMBER 1975 – REVISED MAY 1995
TYPICAL CHARACTERISTICS
SN55110A, SN75110A
SN55109A, SN75109A
ON-STATE OUTPUT CURRENT
vs
NEGATIVE SUPPLY VOLTAGE
ON-STATE OUTPUT CURRENT
vs
NEGATIVE SUPPLY VOLTAGE
14
6
IIO(on)
O(on) – On-State Output Current – mA
VCC+ = 4.5 V
VO = – 3 V
TA = 25°C
5
4
3
2
1
0
–3
–4
–5
–6
VCC – – Negative Supply Voltage – V
VCC+ = 4.5 V
VO = – 3 V
TA = 25°C
12
10
8
6
4
2
0
–7
–3
–4
–5
–6
VCC – – Negative Supply Voltage – V
Figure 2
–7
Figure 3
SN75112
ON-STATE OUTPUT CURRENT
vs
NEGATIVE SUPPLY VOLTAGE
35
IIO(on)
O(on) – On-State Output Current – mA
IIO(on)
O(on) – On-State Output Current – mA
7
30
VCC+ = 4.5 V
VO = – 3 V
TA = 25°C
25
20
15
10
5
0
–3
–4
–5
–6
VCC – – Negative Supply Voltage – V
–7
Figure 4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
2–7
SN55109A, SN55110A
SN75109A, SN75110A, SN75112
DUAL LINE DRIVERS
SLLS106B – DECEMBER 1975 – REVISED MAY 1995
APPLICATION INFORMATION
special pulse-control circuit
Figure 5 shows a circuit that may be used as a pulse generator output or in many other testing applications.
INPUT
A
OUTPUTS
Y
Z
High
Low
Off
On
On
Off
5V
VCC +
Y
A
Input
3
3
2
4
4
2
5
1
6
5
1
6
B
2.5 V
Z
3
C
4
2
D
GND
1/2 ‘109A
‘110A,
or SN75112
5
VCC –
1
6
Output
–5 V
To Other Logic and
Strobe Inputs
Input Pulse
0V
Switch
Position
1
2
3
4
Output Pulse
6
0V
Figure 5. Pulse-Control Circuit
2–8
5
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN55109A, SN55110A
SN75109A, SN75110A, SN75112
DUAL LINE DRIVERS
SLLS106B – DECEMBER 1975 – REVISED MAY 1995
APPLICATION INFORMATION
using the SN75112 as a CCITT recommended V.35 line driver
The SN75112 dual line driver, the SN75107A dual line receiver, and some external resistors can be used to
implement the data interchange circuit of CCITT recommendation V.35 (1976) modem specification. The circuit
of one channel is shown in Figure 1 and meets the requirement of the interface as specified by Appendix 11 of
CCITT V.35 and summarized in Table 1 (V.35 has been replaced by ITU V.11).
Table 1. CCITT V.35 Electrical Requirements
GENERATOR
Source impedance, Zsource
MIN
MAX
UNIT
50
150
Ω
Resistance to ground, R
135
165
Ω
Differential output voltage, VOD
440
660
mV
10% to 90% rise time, tr
40
ns
0.01 × ui †
or
Common-mode output voltage, VOC
– 0.6
0.6
V
90
110
Ω
Resistance to ground, R
135
165
† ui = unit interval or minimum signal element pulse width
Ω
LOAD (RECEIVER)
Input impedance, ZI
5V
5V
5V
R3
390 Ω
Strobe
1/2 SN75112
R1
1.3 kΩ
100 pF
1A 1
13
Data In 2
1B
12
1Y
R5
75 Ω
1Z
R6
50 Ω
R8
125 Ω
Enable 3
1C
R4
390 Ω
100 pF
1A
1
4
1Y
Data Out
5
1G
Enable
2
R7
50 Ω
10
6
1B
1/2 SN75107A
R2
1.3 kΩ
5V
All resistors are 5%, 1/4 W.
Figure 6. CCITT Recommended V.35 Interface Using the SN75112 and SN75107A
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
2–9
SN55109A, SN55110A
SN75109A, SN75110A, SN75112
DUAL LINE DRIVERS
SLLS106B – DECEMBER 1975 – REVISED MAY 1995
2–10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments (TI) reserves the right to make changes to its products or to discontinue any semiconductor
product or service without notice, and advises its customers to obtain the latest version of relevant information
to verify, before placing orders, that the information being relied on is current and complete.
TI warrants performance of its semiconductor products and related software to the specifications applicable at
the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are
utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each
device is not necessarily performed, except those mandated by government requirements.
Certain applications using semiconductor products may involve potential risks of death, personal injury, or
severe property or environmental damage (“Critical Applications”).
TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED
TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS.
Inclusion of TI products in such applications is understood to be fully at the risk of the customer. Use of TI
products in such applications requires the written approval of an appropriate TI officer. Questions concerning
potential risk applications should be directed to TI through a local SC sales office.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards should be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance, customer product design, software performance, or
infringement of patents or services described herein. Nor does TI warrant or represent that any license, either
express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property
right of TI covering or relating to any combination, machine, or process in which such semiconductor products
or services might be or are used.
Copyright  1998, Texas Instruments Incorporated