TI SN75C1154DW

SN65C1154, SN75C1154
QUADRUPLE LOW-POWER DRIVERS/RECEIVERS
SLLS151D – DECEMBER 1988 – REVISED APRIL 2003
D
D
D
D
D
D
D
SN65C1154 . . . N PACKAGE
SN75C1154 . . . DW, N, OR NS PACKAGE
(TOP VIEW)
Meet or Exceed the Requirements of
TIA/EIA-232-F and ITU Recommendation
V.28
Very Low Power Consumption . . .
5 mW Typ
Wide Driver Supply Voltage . . .
±4.5 V to ±15 V
Driver Output Slew Rate Limited to
30 V/µs Max
Receiver Input Hysteresis . . . 1000 mV Typ
Push-Pull Receiver Outputs
On-Chip Receiver 1-µs Noise Filter
VDD
1RA
1DY
2RA
2DY
3RA
3DY
4RA
4DY
VSS
1
20
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
11
VCC
1RY
1DA
2RY
2DA
3RY
3DA
4RY
4DA
GND
description/ordering information
The SN65C1164 and SN75C1154 are low-power BiMOS devices containing four independent drivers and
receivers that are used to interface data terminal equipment (DTE) with data circuit-terminating equipment
(DCE). These devices are designed to conform to TIA/EIA-232-F. The drivers and receivers of the SN65C1154
and SN75C1154 are similar to those of the SN75C188 quadruple driver and SN75C189A quadruple receiver,
respectively. The drivers have a controlled output slew rate that is limited to a maximum of 30 V/µs and the
receivers have filters that reject input noise pulses of shorter than 1 µs. Both these features eliminate the need
for external components.
The SN65C1154 and SN75C1154 have been designed using low-power techniques in a BiMOS technology.
In most applications, the receivers contained in these devices interface to single inputs of peripheral devices
such as ACEs, UARTs, or microprocessors. By using sampling, such peripheral devices usually are insensitive
to the transition times of the input signals. If this is not the case, or for other uses, it is recommended that the
SN65C1154 and SN75C1154 receiver outputs be buffered by single Schmitt input gates or single gates of the
HCMOS, ALS, or 74F logic families.
ORDERING INFORMATION
–40°C to 85°C
0°C to 70°C
ORDERABLE
PART NUMBER
PACKAGE†
TA
TOP-SIDE
MARKING
PDIP (N)
Tube of 20
SN65C1154N
SN65C1154N
PDIP (N)
Tube of 20
SN75C1154N
SN75C1154N
Tube of 25
SN75C1154DW
Reel of 2500
SN75C1154DWR
SOIC (DW)
SN75C1154
SOP (NS)
Reel of 2000
SN75C1154NSR
SN75C1154
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are
available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2003, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SN65C1154, SN75C1154
QUADRUPLE LOW-POWER DRIVERS/RECEIVERS
SLLS151D – DECEMBER 1988 – REVISED APRIL 2003
logic diagram (positive logic)
Typical of Each Receiver
RA
2, 4, 6, 8
19, 17, 15, 13
RY
Typical of Each Driver
DY
2
3, 5, 7, 9
POST OFFICE BOX 655303
18, 16, 14, 12
• DALLAS, TEXAS 75265
DA
SN65C1154, SN75C1154
QUADRUPLE LOW-POWER DRIVERS/RECEIVERS
SLLS151D – DECEMBER 1988 – REVISED APRIL 2003
schematics of inputs and outputs
EQUIVALENT DRIVER INPUT
VDD
EQUIVALENT DRIVER OUTPUT
VDD
Internal
1.4-V Reference
Input
DA
160 Ω
VSS
Output
DY
74 Ω
GND
72 Ω
VSS
Input
RA
EQUIVALENT RECEIVER INPUT
3.4 kΩ
EQUIVALENT RECEIVER OUTPUT
VCC
1.5 kΩ
ESD
Protection
ESD
Protection
Output
RY
530 Ω
GND
GND
Resistor values shown are nominal.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SN65C1154, SN75C1154
QUADRUPLE LOW-POWER DRIVERS/RECEIVERS
SLLS151D – DECEMBER 1988 – REVISED APRIL 2003
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage: VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 V
VSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –15 V
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage range, VI: Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VSS to VDD
Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –30 V to 30 V
Output voltage range, VO:Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (VSS – 6 V) to (VDD + 6 V)
Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to (VCC + 0.3 V)
Package thermal impedance, θJA (see Notes 2 and 3): DW package . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W
N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69°C/W
NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . 60°C/W
Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage s are with respect to the network GND terminal.
2. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable
ambient temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
3. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions
4
MIN
NOM
MAX
VDD
VSS
Supply voltage
4.5
12
15
V
Supply voltage
–4.5
–12
–15
V
VCC
Supply voltage
4.5
5
6
V
VDD
±25
V
Driver
VSS + 2
UNIT
VI
Input voltage
VIH
VIL
High-level input voltage
Driver
Low-level input voltage
Driver
0.8
V
IOH
IOL
High-level output current
Receiver
–1
mA
High-level output current
Receiver
3.2
mA
TA
Operating
O
erating free-air tem
temperature
erature
Receiver
POST OFFICE BOX 655303
2
V
SN65C1154
–40
85
SN75C1154
0
70
• DALLAS, TEXAS 75265
°C
SN65C1154, SN75C1154
QUADRUPLE LOW-POWER DRIVERS/RECEIVERS
SLLS151D – DECEMBER 1988 – REVISED APRIL 2003
DRIVER SECTION
electrical characteristics over operating free-air temperature range, VDD = 12 V, VSS = –12 V,
VCC = 5 V ±10% (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VDD = 5 V,
VDD = 12 V,
VSS = –5 V
VSS = –12 V
VDD = 5 V,
VDD = 12 V,
VSS = –5 V
VSS = –12 V
TYP†
4
4.5
10
10.8
MAX
UNIT
VOH
High level output voltage
High-level
VIL = 0.8 V,,
See Figure 1
VOL
Low-level output voltage
g
(see Note 4)
VIH = 2 V,,
See Figure 1
RL = 3 kΩ,,
High-level input current
See Figure 2
1
µA
Low-level input current
VI = 5 V,
VI = 0,
See Figure 2
–1
µA
IOS(H)
High-level
g
short-circuit
output current‡
VI = 0
0.8
8V
V,
VO = 0 or VSS,
See Figure 1
–7.5
75
–12
12
–19.5
19 5
mA
IOS(L)
Low-level short-circuit
output current‡
VI = 2 V
V,
VO = 0 or VDD,
See Figure 1
75
7.5
12
19 5
19.5
mA
IDD
Supply current from VDD
No load,
All inputs at 2 V or 0.8 V
VDD = 5 V,
VDD = 12 V,
VSS = –5 V
VSS = –12 V
115
250
115
250
ISS
Supply current from VSS
No load,
All inputs at 2 V or 0.8 V
VDD = 5 V,
VDD = 12 V,
VSS = –5 V
VSS = –12 V
–115
–250
–115
–250
IIH
IIL
RL = 3 kΩ,,
MIN
V
–4.4
–4
–10.7
–10
V
µA
µA
ro
Output resistance
VDD = VSS = VCC = 0,
VO = –2 V to 2 V,
See Note 5
300
400
Ω
† All typical values are at TA = 25°C.
‡ Not more than one output should be shorted at one time.
NOTES: 4. The algebraic convention, where the more positive (less negative) limit is designated as maximum, is used in this data sheet for logic
levels only.
5. Test conditions are those specified by TIA/EIA-232-F.
switching characteristics, VDD = 12 V, VSS = –12 V, VCC = 5 V ±10%, TA = 25°C (see Figure 3)
TYP
MAX
tPLH
tPHL
Propagation delay time, low- to high-level output§
Propagation delay time, high- to low-level output§
PARAMETER
RL = 3 to 7 kΩ,
TEST CONDITIONS
CL = 15 pF
MIN
1.2
3
µs
RL = 3 to 7 kΩ,
CL = 15 pF
2.5
3.5
µs
tTLH
tTHL
Transition time, low- to high-level output¶
Transition time, high- to low-level output¶
RL = 3 to 7 kΩ,
CL = 15 pF
0.53
2
3.2
µs
RL = 3 to 7 kΩ,
CL = 15 pF
0.53
2
3.2
µs
tTLH
tTHL
Transition time, low- to high-level output#
Transition time, high- to low-level output#
RL = 3 to 7 kΩ,
CL = 2500 pF
1
2
µs
RL = 3 to 7 kΩ,
CL = 2500 pF
1
2
µs
SR
Output slew rate
RL = 3 to 7 kΩ,
CL = 15 pF
10
30
V/µs
4
UNIT
§ tPHL and tPLH include the additional time due to on-chip slew rate control and are measured at the 50% points.
¶ Measured between 10% and 90% points of output waveform
# Measured between 3 V and –3 V points of output waveform (TIA/EIA-232-F conditions) with all unused inputs tied either high or low
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SN65C1154, SN75C1154
QUADRUPLE LOW-POWER DRIVERS/RECEIVERS
SLLS151D – DECEMBER 1988 – REVISED APRIL 2003
RECEIVER SECTION
electrical characteristics over operating free-air temperature range, VDD = 12 V, VSS = –12 V,
= 5 V ± 10% (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP†
MAX
UNIT
VIT
IT+
Positive-going
g g input
threshold voltage
See Figure 5
17
1.7
21
2.1
2 55
2.55
V
VIT
IT–
Negative-going
g
g g input
threshold voltage
See Figure 5
0 65
0.65
1
1 25
1.25
V
Vhys
Input hysteresis voltage
(VIT+ – VIT–)
600
1000
VI = 0.75 V,
VOH
High level output voltage
High-level
VI = 0
0.75
75 V
V,
See Figure 5
VOL
Low-level output voltage
VI = 3 V,
VI = 25 V
IOH = –20 µA,
IOH = –1
1 mA,
A
IOL = 3.2 mA,
See Figure 5 and Note 6
3.5
VCC = 4.5 V
VCC = 5 V
2.8
4.4
3.8
4.9
VCC = 5.5 V
See Figure 5
4.3
mV
V
5.4
0.17
0.4
3.6
4.6
8.3
VI = 3 V
VI = –25 V
0.43
0.55
1
–3.6
–5
–8.3
VI = –3 V
–0.43
–0.55
–1
V
IIH
High level input current
High-level
IIL
Low level input current
Low-level
IOS(H)
Short-circuit output
at high level
75 V
VI = 0
0.75
V,
VO = 0
0,
See Figure 4
8
–8
15
–15
mA
IOS(L)
Short-circuit output
at low level
VI = VCC,
VO = VCC,
See Figure 4
13
25
mA
ICC
Supply current from VCC
No load,
All inputs at 0 or 5 V
400
600
400
600
VDD = 5 V,
VDD = 12 V,
VSS = –5 V
VSS = –12 V
mA
mA
µA
† All typical values are at TA = 25°C.
NOTE 6: If the inputs are left unconnected, the receiver interprets this as an input low and the receiver outputs will remain in the high state.
switching characteristics, VDD = 12 V, VSS = –12 V, VCC = 5 V ± 10%, TA = 25°C
PARAMETER
TEST CONDITIONS
TYP
MAX
See Figure 6
3
4
µs
RL = 5 kΩ,
See Figure 6
3
4
µs
CL = 50 pF,
RL = 5 kΩ,
See Figure 6
300
450
ns
Transition time, high- to low-level output
CL = 50 pF,
RL = 5 kΩ,
See Figure 6
100
300
ns
Duration of longest pulse
rejected as noise‡
CL = 50 pF,
RL = 5 kΩ
4
µs
tPLH
Propagation delay time,
low- to high-level output
CL = 50 pF,
RL = 5 kΩ,
tPHL
Propagation delay time,
high- to low-level output
CL = 50 pF,
Transition time, low- to high-level output
tTLH
tTHL
tw(N)
MIN
1
UNIT
‡ The receiver ignores any positive- or negative-going pulse that is less than the minimum value of tw(N) and accepts any positive- or negative-going
pulse greater than the maximum of tw(N).
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN65C1154, SN75C1154
QUADRUPLE LOW-POWER DRIVERS/RECEIVERS
SLLS151D – DECEMBER 1988 – REVISED APRIL 2003
PARAMETER MEASUREMENT INFORMATION
IOSL
VDD
VCC
VDD
VCC
VDD or GND
–IOSH
IIH
VSS or GND
VI
VI
–IIL
RL = 3 kΩ
VO
VI
VSS
VSS
Figure 1. Driver Test Circuit
(VOH, VOL, IOSL, IOSH)
Figure 2. Driver Test Circuit (IIL, IIH)
3V
VDD
Input
VCC
Input
1.5
1.5
0V
Pulse
Generator
(see Note A)
tPHL
CL
(see Note B)
RL
tPLH
50%
10%
50%
10%
Output
tTHL
VSS
VOH
90%
90%
tTLH
VOL
VOLTAGE WAVEFORMS
TEST CIRCUIT
NOTES: A. The pulse generator has the following characteristics: tw = 25 µs, PRR = 20 kHz, ZO = 50 Ω, tr = tf < 50 ns.
B. CL includes probe and jig capacitance.
Figure 3. Driver Test Circuit and Voltage Waveforms
VDD
VCC
VI
–IOS(H)
VDD
VCC
IOS(L)
VIT, VI
VCC
VOH
VOL
VSS
–IOH
IOL
VSS
Figure 4. Receiver Test Circuit (IOSH, IOSL)
POST OFFICE BOX 655303
Figure 5. Receiver Test Circuit (VIT, VOL, VOH)
• DALLAS, TEXAS 75265
7
SN65C1154, SN75C1154
QUADRUPLE LOW-POWER DRIVERS/RECEIVERS
SLLS151D – DECEMBER 1988 – REVISED APRIL 2003
PARAMETER MEASUREMENT INFORMATION
4V
VDD
Input
Input
VCC
50%
50%
0V
Pulse
Generator
(see Note A)
tPHL
RL
CL
(see Note B)
tPLH
90%
90%
50%
10%
Output
50%
10%
tTHL
VSS
tTLH
VOLTAGE WAVEFORMS
TEST CIRCUIT
NOTES: A. The pulse generator has the following characteristics: tw = 25 µs, PRR = 20 kHz, ZO = 50 Ω, tr = tf < 50 ns.
B. CL includes probe and jig capacitance.
Figure 6. Receiver Test Circuit and Voltage Waveforms
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
VOH
VOL
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2004, Texas Instruments Incorporated