LTC3633A/LTC3633A-1 Dual Channel 3A, 20V Monolithic Synchronous Step-Down Regulator DESCRIPTION FEATURES n n n n n n n n n n n n n n n n n 3.6V to 20V Input Voltage Range 3A Output Current per Channel Up to 95% Efficiency Low Duty Cycle Operation: 5% at 2.25MHz Selectable 0°/180° Phase Shift Between Channels Adjustable Switching Frequency: 500kHz to 4MHz External Frequency Synchronization Current Mode Operation for Excellent Line and Load Transient Response 0.6V Reference Allows Low Output Voltages User Selectable Burst Mode® Operation or Forced Continuous Mode Operation Output Voltage Tracking and Soft-Start Capability Short-Circuit Protected Overvoltage Input and Overtemperature Protection Power Good Status Outputs LTC3633: 16V Absolute Maximum VIN LTC3633A: 20V Absolute Maximum VIN, Pin Compatible with LTC3633 Low Profile (4mm × 5mm) QFN-28 and 28-Lead TSSOP Packages APPLICATIONS n n n Distributed Power Systems Battery Powered Instruments Point of Load Power Supplies The LTC®3633A is a high efficiency, dual-channel monolithic synchronous buck regulator using a controlled on-time, current mode architecture, with phase lockable switching frequency. The two channels can run 180° out of phase to relax the requirements for input and output capacitance. The operating supply voltage range is from 3.6V to 20V, making it suitable for lithium-ion battery stacks as well as point of load power supply applications from a 12V or 5V supply. The operating frequency is programmable from 500kHz to 4MHz with an external resistor and may be synchronized to an external clock signal. The high frequency capability allows the use of small surface mount inductors and capacitors. The unique constant frequency/controlled ontime architecture is ideal for high step-down ratio applications that operate at high frequency while demanding fast transient response. An internal phase locked loop servos the on-time of the internal one-shot timer to match the frequency of the internal clock or an applied external clock. The LTC3633A can select between forced continuous mode and high efficiency Burst Mode operation. The LTC3633A and LTC3633A-1 differ in their output voltage sense range (refer to Table 1 in the Operation section for a description of the entire LTC3633A product family). L, LT, LTC, LTM, Burst Mode, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 5481178, 5847554, 6580258, 6304066, 6476589, 6774611. TYPICAL APPLICATION Efficiency vs Load Current VIN 6V TO 20V 47μF x2 RUN1 RUN2 VIN2 VIN1 100 INTVCC ITH1 ITH2 90 2.2μF 80 LTC3633A TRACKSS2 PGOOD2 VOUT2 5V AT 3A 1.5μH BOOST2 0.1μF SW2 VON2 VFB2 22μF 73.2k 10k SGND PGND EFFICIENCY (%) RT MODE/SYNC PHMODE V2P5 TRACKSS1 PGOOD1 BOOST1 Burst Mode OPERATION 70 60 50 40 30 0.1μF SW1 VON1 VFB1 10k 45.3k 1μH 20 VOUT1 3.3V AT 3A 22μF 10 VIN = 12V 0 0.01 0.001 VOUT = 5V VOUT = 3.3V 1 0.1 LOAD CURRENT (A) 10 3633a TA01b 3633a TA01a 3633a1f 1 LTC3633A/LTC3633A-1 ABSOLUTE MAXIMUM RATINGS (Note 1) VIN1, VIN2 ................................................... –0.3V to 20V PGOOD1, PGOOD2, VON1, VON2 ................. –0.3V to 18V BOOST1, BOOST2 ...................................... –0.3V to 23V BOOST1-SW1, BOOST2-SW2 ................... –0.3V to 3.6V V2P5, INTVCC, TRACKSS1, TRACKSS2 ...... –0.3V to 3.6V ITH1, ITH2, RT, MODE/SYNC ........ –0.3V to INTVCC + 0.3V VFB1, VFB2, PHMODE. .................. –0.3V to INTVCC + 0.3V RUN1, RUN2 .................................... –0.3V to VIN + 0.3V SW1, SW2 ....................................... –0.3V to VIN + 0.3V Operating Junction Temperature Range (Notes 2, 3) ............................................ –40°C to 125°C Storage Temperature Range................... –65°C to 150°C PIN CONFIGURATION TOP VIEW 28 27 26 25 24 23 3 26 SW1 4 25 VIN1 24 VIN1 SW1 27 SW1 VFB1 VON1 28 VON1 2 ITH1 1 TRACKSS1 VFB1 ITH1 SW1 TRACKSS1 TOP VIEW PGOOD1 1 22 VIN1 PGOOD1 PHMODE 2 21 VIN1 PHMODE 5 RUN1 6 MODE/SYNC 7 RT 8 9 RUN1 3 20 BOOST1 MODE/SYNC 4 19 INTVCC 29 PGND RT 5 18 V2P5 23 BOOST1 29 PGND 22 INTVCC 21 V2P5 RUN2 6 17 BOOST2 RUN2 SGND 7 16 VIN2 SGND 10 19 VIN2 PGOOD2 8 15 VIN2 PGOOD2 11 18 VIN2 VFB2 12 17 SW2 TRACKSS2 13 16 SW2 ITH2 14 15 VON2 SW2 SW2 VON2 ITH2 VFB2 TRACKSS2 9 10 11 12 13 14 UFD PACKAGE 28-LEAD (4mm × 5mm) PLASTIC QFN 20 BOOST2 FE PACKAGE 28-LEAD PLASTIC TSSOP TJMAX = 125°C, θJA = 43°C/W EXPOSED PAD (PIN 29) IS PGND, MUST BE SOLDERED TO PCB TJMAX = 125°C, θJA = 30°C/W EXPOSED PAD (PIN 29) IS PGND, MUST BE SOLDERED TO PCB ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3633AEUFD#PBF LTC3633AEUFD#TRPBF 3633A 28-Lead (4mm × 5mm) Plastic QFN –40°C to 125°C LTC3633AIUFD#PBF LTC3633AIUFD#TRPBF 3633A 28-Lead (4mm × 5mm) Plastic QFN –40°C to 125°C LTC3633AEFE#PBF LTC3633AEFE#TRPBF LTC3633AFE 28-Lead Plastic TSSOP –40°C to 125°C LTC3633AIFE#PBF LTC3633AIFE#TRPBF LTC3633AFE 28-Lead Plastic TSSOP –40°C to 125°C LTC3633AEUFD-1#PBF LTC3633AEUFD-1#TRPBF 633A1 28-Lead (4mm × 5mm) Plastic QFN –40°C to 125°C LTC3633AIUFD-1#PBF LTC3633AIUFD-1#TRPBF 633A1 28-Lead (4mm × 5mm) Plastic QFN –40°C to 125°C LTC3633AEFE-1#PBF LTC3633AEFE-1#TRPBF LTC3633AFE-1 28-Lead Plastic TSSOP –40°C to 125°C LTC3633AIFE-1#PBF LTC3633AIFE-1#TRPBF LTC3633AFE-1 28-Lead Plastic TSSOP –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 3633a1f 2 LTC3633A/LTC3633A-1 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TJ = 25°C (Note 2). VIN1 = VIN2 = 12V, unless otherwise noted. SYMBOL PARAMETER VIN1 Supply Range VIN1 Supply Range VIN2 Supply Range Output Voltage Range (Note 4) IQ Input DC Supply Current (VIN1 + VIN2) Both Channels Active (Note 5) Sleep Current Shutdown CONDITIONS 3.6V < VIN1 < 20V MIN TYP MAX UNITS l 3.6 20 V l l 3.6 1.5 20 20 V V 0.6 1.5 6 12 V V LTC3633A, VON = VOUT LTC3633A-1, VON = VOUT MODE = 0V MODE = INTVCC, VFB1, VFB2 > 0.6 RUN1 = RUN2 = 0V 1.3 500 13 l mA μA μA VFB Feedback Reference Voltage ΔVLINE_REG Reference Voltage Line Regulation VIN = 3.6V to 20V 0.002 %/V ΔVLOAD_REG Output Voltage Load Regulation ITH = 0.8V to 1.6V 0.05 % 0.594 0.6 0.606 ±30 V IFB Feedback Pin Input Current gm(EA) Error Amplifier Transconductance ITH = 1.2V 1.8 mS tON Minimum On Time VON = 0.6V, VIN = 4V 20 ns tOFF Minimum Off Time VIN = 6V fOSC Oscillator Frequency VRT = INTVCC RT = 162k RT = 80.6k ILIM Valley Switch Current Limit RDS(ON) Top Switch On-Resistance Bottom Switch On-Resistance ISW(LKG) Switch Leakage Current VIN = 20V, VRUN = 0V 0.01 ±1 μA V VIN-OV VIN Overvoltage Lockout Threshold VIN Rising VIN Falling 20.3 22.5 21.5 22.5 V V INTVCC Voltage 3.6V < VIN < 20V, 0mA Load 3.1 3.3 3.5 V INTVCC Load Regulation 0mA to 50mA Load, VIN = 4V to 20V RUN Leakage Current VIN = 20V V2P5 Voltage ILOAD = 0mA to 10mA PGOOD Good-to-Bad Threshold VFB Rising VFB Falling PGOOD Bad-to-Good Threshold VFB Rising VFB Falling RPGOOD PGOOD Pull-Down Resistance 10mA Load tPGOOD Power Good Filter Time tSS Internal Soft-Start Time 10% to 90% Rise Time VFB During Tracking TRACKSS = 0.3V TRACKSS Pull-Up Current ns 1.4 1.7 3.4 2 2 4 2.6 2.3 4.6 MHz MHz MHz 2.6 3.5 4.5 A 130 65 RUN Threshold Rising RUN Threshold Falling ITRACKSS 45 nA mΩ mΩ 1.3 l l 1.18 0.98 1.22 1.01 l 2.46 8 –8 –3 3 20 0.28 % 1.26 1.04 V V 0 ±3 μA 2.5 2.54 V 10 –10 % % –5 5 % % 20 Ω 40 μs 400 700 μs 0.3 0.315 V 1.4 μA 3633a1f 3 LTC3633A/LTC3633A-1 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TJ = 25°C (Note 2). VIN1 = VIN2 = 12V, unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN VPHMODE PHMODE Threshold Voltage PHMODE VIH PHMODE VIL 1 MODE VIH MODE VIL 1 SYNC Threshold Voltage SYNC VIH 0.95 MODE/SYNC Input Current MODE = 0V MODE = INTVCC VMODE/SYNC IMODE MODE/SYNC Threshold Voltage Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3633A is tested under pulsed load conditions such that TJ ≈ TA. The LTC3633AE is guaranteed to meet specifications from 0°C to 85°C junction temperature. Specifications over the –40°C to 125°C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC3633AI is guaranteed over the full –40°C to 125°C operating junction temperature range. Note that the maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal impedance and other environmental factors. The junction temperature TYP MAX UNITS 0.3 V V 0.4 V V V 1.5 –1.5 μA μA (TJ, in °C) is calculated from the ambient temperature (TA, in °C) and power dissipation (PD, in Watts) according to the formula: TJ = TA + (PD • θJA), where θJA (in °C/W) is the package thermal impedance. Note 3: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed 125°C when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability. Note 4: Output voltages outside the specified range are not optimized for controlled on-time operation. Refer to the Applications Information section for further discussions related to the output voltage range. Note 5: Dynamic supply current is higher due to the internal gate charge being delivered at the switching frequency. 3633a1f 4 LTC3633A/LTC3633A-1 TYPICAL PERFORMANCE CHARACTERISTICS unless otherwise noted. Efficiency vs Load Current Forced Continuous Mode Operation Efficiency vs Load Current Burst Mode Operation 100 100 VOUT = 1.8V 90 Efficiency vs Load Current 100 VOUT = 1.8V 80 70 70 50 40 EFFICIENCY (%) 80 70 60 60 50 40 30 30 VIN = 4V VIN = 8V VIN = 12V VIN = 20V 20 10 0 0.001 0.01 1 0.1 LOAD CURRENT (A) VIN = 4V VIN = 8V VIN = 12V VIN = 20V 10 0 0.001 0.01 1 0.1 LOAD CURRENT (A) Efficiency vs Load Current Burst Mode Operation 100 L = 2.2μH VOUT = 5V VOUT = 3.3V VOUT = 5V VOUT = 3.3V 20 10 0 0.001 10 0.01 1 0.1 LOAD CURRENT (A) 10 3633a G03 Reference Voltage vs Temperature 0.605 VOUT = 1.8V 0.603 90 60 50 40 30 VIN = 4V VIN = 8V VIN = 12V VIN =15V VIN = 20V 20 10 0 0.0001 0.001 0.01 0.1 LOAD CURRENT (A) 1 85 VFB (V) 70 EFFICIENCY (%) EFFICIENCY (%) 40 95 80 80 70 ILOAD = 10mA ILOAD = 100mA ILOAD = 1A ILOAD = 3A 65 60 10 4 6 8 10 12 14 16 INPUT VOLTAGE (V) 0.597 18 20 0.595 –50 –25 Oscillator Internal Set Frequency vs Temperature 10 Burst Mode OPERATION FORCED CONTINUOUS 2.6 8 0.8 0.4 0.0 RT = INTVCC 2.4 6 4 FREQUENCY (MHz) FREQUENCY VARIATION (%) VOUT = 1.8V 25 50 75 100 125 150 TEMPERATURE (°C) 3633a G06 Oscillator Frequency vs Temperature 1.2 0 3633a G05 Load Regulation 1.6 0.601 0.599 75 3633a G04 ΔVOUT/VOUT (%) 50 Efficiency vs Input Voltage Burst Mode Operation VOUT = 1.2V 90 60 3633a G02 3633a G01 100 FORCED CONTINUOUS OPERATION 30 20 10 Burst Mode OPERATION 90 80 EFFICIENCY (%) EFFICIENCY (%) 90 TJ = 25°C, VIN1 = VIN2 = 12V, fSW = 1MHz, L = 1μH 2 0 –2 –4 –6 2.2 2.0 1.8 1.6 –8 –0.4 0 0.5 1 2 1.5 ILOAD (A) 2.5 3 3633a G07 –10 –50 –25 0 50 75 25 TEMPERATURE (°C) 100 125 3633a G08 1.4 –50 –25 0 50 75 25 TEMPERATURE (°C) 100 125 3633a G09 3633a1f 5 LTC3633A/LTC3633A-1 TYPICAL PERFORMANCE CHARACTERISTICS unless otherwise noted. Quiescent Current vs VIN Burst Mode Operation Internal MOSFET RDS(ON) vs Temperature 200 900 180 800 160 700 22 100 80 18 16 25°C 500 IQ (μA) TOP SWITCH 120 90°C 600 IQ (μA) RDS(ON) (mΩ) Shutdown Current vs VIN 24 20 140 –40°C 400 300 60 BOTTOM SWITCH 40 200 20 100 14 12 10 8 6 4 0 –50 0 25 75 50 TEMPERATURE (°C) –25 100 0 125 2 4 6 8 10 12 14 VIN (V) 16 3633a G10 0 20 SYNCHRONOUS SWITCH MAIN SWITCH 8000 7000 3.9 2.0 3.8 1.8 3.6 4000 3.5 3000 2000 8 10 12 14 VIN (V) 16 18 20 1.6 ITRACKSS (μA) ILIM (A) 5000 6 TRACKSS Pull-Up Current vs Temperature 3.7 6000 4 3633a G12 Valley Current Limit vs Temperature 10000 9000 18 3633a G11 Switch Leakage vs Temperature LEAKAGE CURRENT (nA) TJ = 25°C, VIN1 = VIN2 = 12V, fSW = 1MHz, L = 1μH 1.4 1.2 1.0 3.4 0.8 1000 0 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 3.3 –50 –25 0 25 75 50 TEMPERATURE (°C) 100 125 0.6 –50 –25 50 25 75 0 TEMPERATURE (°C) 3633a G14 3633a G13 V2P5 Load Regulation 100 125 3633a G15 Burst Mode Operation Load Step V2P5(V) 2.506 2.504 SW 10V/DIV 2.502 VOUT 50mV/DIV VOUT AC-COUPLED 100mV/DIV 2.500 IL 2A/DIV IL 1A/DIV 2.498 2.496 2.494 5μs/DIV VOUT = 1.8V ILOAD = 100mA 0 2 4 6 ILOAD (mA) 8 10 3633a G17 20μs/DIV VOUT = 1.8V ILOAD = 100mA to 3A CITH = 220pF RITH = 13kΩ 3633a G18 3633a G16 3633a1f 6 LTC3633A/LTC3633A-1 TYPICAL PERFORMANCE CHARACTERISTICS unless otherwise noted. Load Step (Internal Compensation) VOUT AC-COUPLED 100mV/DIV IL 2A/DIV 20μs/DIV VOUT = 1.8V ILOAD = 100mA to 3A ITH = INTVCC Start-Up (Burst Mode Operation) RUN 2V/DIV VOUT 1V/DIV VOUT 1V/DIV IL 2A/DIV IL 1A/DIV 3633a G19 3633a G20 400μs/DIV 400μs/DIV 3633a G21 VOUT = 1.8V CSS = 4.7nF ILOAD = 150mA VOUT = 1.8V CSS = 4.7nF ILOAD = 150mA Start-Up into Prebiased Output (Forced Continuous Mode) RUN 2V/DIV RUN 2V/DIV VOUT 1.8V 1V/DIV VOUT 1.8V 1V/DIV IL 1A/DIV IL 2A/DIV 200μs/DIV Start-Up (Forced Continuous Mode) RUN 2V/DIV Start-Up into Prebiased Output (Burst Mode Operation) ILOAD = 0mA TJ = 25°C, VIN1 = VIN2 = 12V, fSW = 1MHz, L = 1μH 3633a G22 1ms/DIV 3633a G22 ILOAD = 0mA 3633a1f 7 LTC3633A/LTC3633A-1 PIN FUNCTIONS (QFN/TSSOP) PGOOD1 (Pin 1/Pin 4): Channel 1 Open-Drain Power Good Output Pin. PGOOD1 is pulled to ground when the voltage on the VFB1 pin is not within ±8% (typical) of the internal 0.6V reference. PGOOD1 becomes high impedance once the VFB1 pin returns to within ±5% (typical) of the internal reference. PHMODE (Pin 2/Pin 5): Phase Select Input. Tie this pin to ground to force both channels to switch in phase. Tie this pin to INTVCC to force both channels to switch 180° out of phase. Do not float this pin. RUN1 (Pin 3/Pin 6): Channel 1 Regulator Enable Pin. Enables channel 1 operation by tying RUN1 above 1.22V. Tying it below 1V places channel 1 into shutdown. Do not float this pin. MODE/SYNC (Pin 4/Pin 7): Mode Select and External Synchronization Input. Tie this pin to ground to force continuous synchronous operation at all output loads. Floating this pin or tying it to INTVCC enables high efficiency Burst Mode operation at light loads. Drive this pin with a clock to synchronize the LTC3633A switching. An internal phase-locked loop will force the bottom power NMOS’s turn on signal to be synchronized with the rising edge of the CLKIN signal. When this pin is driven with a clock, forced continuous mode is automatically selected. RT (Pin 5/Pin 8): Oscillator Frequency Program Pin. Connect an external resistor (between 80k to 640k) from this pin to SGND in order to program the frequency from 500kHz to 4MHz. When RT is tied to INTVCC, the switching frequency will default to 2MHz. RUN2 (Pin 6/Pin 9): Channel 2 Regulator Enable Pin. Enables channel 2 operation by tying RUN2 above 1.22V. Tying it below 1V places channel 2 into shutdown. Do not float this pin. SGND (Pin 7/Pin 10): Signal Ground Pin. This pin should have a low noise connection to reference ground. The feedback resistor network, external compensation network, and RT resistor should be connected to this ground. PGOOD2 (Pin 8/Pin 11): Channel 2 Open-Drain Power Good Output Pin. PGOOD2 is pulled to ground when the voltage on the VFB2 pin is not within ±8% (typical) of the internal 0.6V reference. PGOOD2 becomes high imped- ance once the VFB2 pin returns to within ±5% (typical) of the internal reference. VFB2 (Pin 9/Pin 12): Channel 2 Output Feedback Voltage Pin. Input to the error amplifier that compares the feedback voltage to the internal 0.6V reference voltage. Connect this pin to a resistor divider network to program the desired output voltage. TRACKSS2 (Pin 10/Pin 13): Output Tracking and Soft-Start Input Pin for Channel 2. Forcing a voltage below 0.6V on this pin bypasses the internal reference input to the error amplifier. The LTC3633A will servo the FB pin to the TRACK voltage under this condition. Above 0.6V, the tracking function stops and the internal reference resumes control of the error amplifier. An internal 1.4μA pull up current from INTVCC allows a soft start function to be implemented by connecting a capacitor between this pin and SGND. ITH2 (Pin 11/Pin 14): Channel 2 Error Amplifier Output and Switching Regulator Compensation Pin. Connect this pin to appropriate external components to compensate the regulator loop frequency response. Connect this pin to INTVCC to use the default internal compensation. VON2 (Pin 12/Pin 15): On-Time Voltage Input for Channel 2. This pin sets the voltage trip point for the on-time comparator. Tying this pin to the output voltage makes the on-time proportional to VOUT2 when VOUT2 is within the VON2 sense range (0.6V – 6V for LTC3633A, 1.5V – 12V for LTC3633A-1). When VOUT2 is outside the VON2 sense range, the switching frequency may deviate from the programmed frequency. The pin impedance is nominally 140kΩ. SW2 (Pins 13, 14/Pins 16, 17): Channel 2 Switch Node Connection to External Inductor. Voltage swing of SW is from a diode voltage drop below ground to VIN. VIN2 (Pins 15, 16/Pins 18, 19): Power Supply Input for Channel 2. Input voltage to the on chip power MOSFETs on channel 2. This input is capable of operating from a different supply voltage than VIN1. BOOST2 (Pin 17/Pin 20): Boosted Floating Driver Supply for Channel 2. The (+) terminal of the bootstrap capacitor connects to this pin while the (–) terminal connects to the SW pin. The normal operation voltage swing of this pin ranges from a diode voltage drop below INTVCC up to VIN+INTVCC. 3633a1f 8 LTC3633A/LTC3633A-1 PIN FUNCTIONS (QFN/TSSOP) V2P5 (Pin 18/Pin 21): 2.5V Regulator Output. Outputs a regulated 2.5V supply voltage capable of supplying 10mA. Bypass this pin with a minimum of 1μF low ESR ceramic capacitor. Tie this pin to INTVCC when this output is not being used in the application. ITH1 (Pin 26/Pin 1): Channel 1 Error Amplifier Output and Switching Regulator Compensation Pin. Connect this pin to appropriate external components to compensate the regulator loop frequency response. Connect this pin to INTVCC to use the default internal compensation. INTVCC (Pin 19/Pin 22): Internal 3.3V Regulator Output. The internal power drivers and control circuits are powered from this voltage. The internal regulator is disabled when both channel 1 and channel 2 are disabled with the RUN1/ RUN2 inputs. Decouple this pin to power ground with a minimum of 1μF low ESR ceramic capacitor. TRACKSS1 (Pin 27/Pin 2): Output Tracking and Soft-Start Input Pin for Channel 1. Forcing a voltage below 0.6V on this pin bypasses the internal reference input to the error amplifier. The LTC3633A will servo the FB pin to the TRACK voltage. Above 0.6V, the tracking function stops and the internal reference resumes control of the error amplifier. An internal 1.4μA pull up current from INTVCC allows a soft-start function to be implemented by connecting a capacitor between this pin and SGND. BOOST1 (Pin 20/Pin 23): Boosted Floating Driver Supply for Channel 1. The (+) terminal of the bootstrap capacitor connects to this pin while the (–) terminal connects to the SW pin. The normal operation voltage swing of this pin ranges from a diode voltage drop below INTVCC up to VIN + INTVCC. VIN1 (Pins 21,22/Pins 24, 25): Power Supply Input for Channel 1. Input voltage to the on chip power MOSFETs on channel 1. The internal LDO for INTVCC is powered off of this pin. SW1 (Pins 23,24/Pins 26, 27): Channel 1 Switch Node Connection to External Inductor. Voltage swing of SW is from a diode voltage drop below ground to VIN. VON1 (Pin 25/Pin 28): On-Time Voltage Input for Channel 1. This pin sets the voltage trip point for the on-time comparator. Tying this pin to the regulated output voltage makes the on-time proportional to VOUT1 when VOUT1 is within the VON1 sense range (0.6V – 6V for LTC3633A, 1.5V – 12V for LTC3633A-1). When VOUT is outside the VON sense range, the switching frequency may deviate from the programmed frequency. The pin impedance is nominally 140kΩ. VFB1 (Pin 28/Pin 3): Channel 1 Output Feedback Voltage Pin. Input to the error amplifier that compares the feedback voltage to the internal 0.6V reference voltage. Connect this pin to a resistor divider network to program the desired output voltage. PGND (Exposed Pad Pin 29/Exposed Pad Pin 29): Power Ground Pin. The (–) terminal of the input bypass capacitor, CIN, and the (–) terminal of the output capacitor, COUT, should be tied to this pin with a low impedance connection. This pin must be soldered to the PCB to provide low impedance electrical contact to power ground and good thermal contact to the PCB. 3633a1f 9 LTC3633A/LTC3633A-1 BLOCK DIAGRAM CIN RUN VON VIN 1.22V 140k + AV = 1 – RUN VIN 0.6V (LTC3633A) 1.5V (LTC3633A-1) ION ION CONTROLLER OSC1 INTVCC 6V (LTC3633A) 12V (LTC3633A-1) tON = VVON IION RUN R S Q ON BOOST SWITCH LOGIC AND ANTISHOOT THROUGH TG M1 + M2 IREV – – L1 COUT BG ICMP CBOOST SW PGND + COMP SELECT SENSE– SENSE+ R2 ITH FB RC IDEAL DIODES CC1 R1 0.6V REF – EA – + 0.648V INTERNAL SOFT-START 0V PGOOD + INTVCC 1.4μA – TRACK – UV TRACKSS SS + 0.552V + FC BURST MODE SELECT CSS 0.48V AT START-UP 0.10V AFTER START-UP CHANNEL 1 OSC1 RT OSC RRT OSC PLL-SYNC MODE/SYNC VIN1 PHMODE PHASE SELECT OSC2 INTVCC 3.3V REG CVCC 2.5V REG V2P5 SGND CHANNEL 2 (SAME AS CHANNEL 1) 3633a BD 3633a1f 10 LTC3633A/LTC3633A-1 OPERATION The LTC3633A is a dual-channel, current mode monolithic step down regulator capable of providing 3A of output current from each channel. Its unique controlled on-time architecture allows extremely low step-down ratios while maintaining a constant switching frequency. Each channel is enabled by raising the voltage on the RUN pin above 1.22V nominally. The LTC3633A has a VON sense range of 0.6V to 6V, while the LTC3633A-1 has a VON sense range of 1.5V to 12V. The following table highlights the difference between the parts in the LTC3633A family. Consult the LTC3633A-2/ LTC3633A-3 data sheet for more details on specific characteristics of those products. Table 1. LTC3633A Family Features PART NUMBER OUTPUT VOLTAGE SVIN V2P5 LTC3633 PIN SENSE RANGE INPUT OUTPUT COMPATIBLE LTC3633A 0.6V to 6V NO YES YES LTC3633A-1 1.5V to 12V NO YES YES LTC3633A-2 0.6V to 6V YES NO NO LTC3633A-3 1.5V to 12V YES NO NO Main Control Loop In normal operation, the internal top power MOSFET is turned on for a fixed interval determined by a fixed oneshot timer (“ON” signal in Block Diagram). When the top power MOSFET turns off, the bottom power MOSFET turns on until the current comparator ICMP trips, thus restarting the one shot timer and initiating the next cycle. Inductor current is measured by sensing the voltage drop across the SW and PGND nodes of the bottom power MOSFET. The voltage on the ITH pin sets the comparator threshold corresponding to inductor valley current. The error amplifier EA adjusts this ITH voltage by comparing an internal 0.6V reference to the feedback signal VFB derived from the output voltage. If the load current increases, it causes a drop in the feedback voltage relative to the internal reference. The ITH voltage then rises until the average inductor current matches that of the load current. The operating frequency is determined by the value of the RT resistor, which programs the current for the internal oscillator. An internal phase-locked loop servos the switching regulator on-time to track the internal oscillator edge and force a constant switching frequency. A clock signal can be applied to the MODE/SYNC pin to synchronize the switching frequency to an external source. The regulator defaults to forced continuous operation once the clock signal is applied. At light load currents, the inductor current can drop to zero and become negative. In Burst Mode operation, a current reversal comparator (IREV) detects the negative inductor current and shuts off the bottom power MOSFET, resulting in discontinuous operation and increased efficiency. Both power MOSFETs will remain off until the ITH voltage rises above the zero current level to initiate another cycle. During this time, the output capacitor supplies the load current and the part is placed into a low current sleep mode. Discontinuous mode operation is disabled by tying the MODE/SYNC pin to ground, which forces continuous synchronous operation regardless of output load current. “Power Good” Status Output The PGOOD open-drain output will be pulled low if the regulator output exits a ±8% window around the regulation point. This condition is released once regulation within a ±5% window is achieved. To prevent unwanted PGOOD glitches during transients or dynamic VOUT changes, the LTC3633A PGOOD falling edge includes a filter time of approximately 40μs. VIN Overvoltage Protection In order to protect the internal power MOSFET devices against transient voltage spikes, the LTC3633A constantly monitors each VIN pin for an overvoltage condition. When VIN rises above 22.5V, the regulator suspends operation by shutting off both power MOSFETs on the corresponding channel. Once VIN drops below 21.5V, the regulator immediately resumes normal operation. The regulator executes its soft-start function when exiting an overvoltage condition. Out-Of-Phase Operation Tying the PHMODE pin high sets the SW2 falling edge to be 180° out of phase with the SW1 falling edge. There is a significant advantage to running both channels out of phase. When running the channels in phase, both top-side MOSFETs are on simultaneously, causing large current pulses to be drawn from the input capacitor and supply at the same time. 3633a1f 11 LTC3633A/LTC3633A-1 OPERATION When running the LTC3633A channels out of phase, the large current pulses are interleaved, effectively reducing the amount of time the pulses overlap. Thus, the total RMS input current is decreased, which both relaxes the capacitance requirements for the VIN bypass capacitors and reduces the voltage noise on the supply line. One potential disadvantage to this configuration occurs when one channel is operating at 50% duty cycle. In this situation, switching noise can potentially couple from one channel to the other, resulting in frequency jitter on one or both channels. This effect can be mitigated with a well designed board layout. APPLICATIONS INFORMATION 6000 5000 FREQUENCY (kHz) A general LTC3633A application circuit is shown on the first page of this data sheet. External component selection is largely driven by the load requirement and switching frequency. Component selection typically begins with the selection of the inductor L and resistor RT. Once the inductor is chosen, the input capacitor, CIN, and the output capacitor, COUT, can be selected. Next, the feedback resistors are selected to set the desired output voltage. Finally, the remaining optional external components can be selected for functions such as external loop compensation, tracking/soft-start, input UVLO, and PGOOD. 4000 3000 2000 1000 0 0 100 200 300 400 500 RT RESISTOR (kΩ) Programming Switching Frequency Selection of the switching frequency is a trade-off between efficiency and component size. High frequency operation allows the use of smaller inductor and capacitor values. Operation at lower frequencies improves efficiency by reducing internal gate charge losses but requires larger inductance values and/or capacitance to maintain low output ripple voltage. Connecting a resistor from the RT pin to SGND programs the switching frequency (f) between 500kHz and 4MHz according to the following formula: 3.2E11 f where RRT is in Ω and f is in Hz. RRT = When RT is tied to INTVCC, the switching frequency will default to approximately 2MHz, as set by an internal resistor. This internal resistor is more sensitive to process and temperature variations than an external resistor (see Typical Performance Characteristics) and is best used for applications where switching frequency accuracy is not critical. 600 700 3633a F01 Figure 1. Switching Frequency vs RT Inductor Selection For a given input and output voltage, the inductor value and operating frequency determine the inductor ripple current. More specifically, the inductor ripple current decreases with higher inductor value or higher operating frequency according to the following equation: ⎞ ⎛V ⎞⎛ V ΔIL = ⎜ OUT ⎟ ⎜1– OUT ⎟ ⎝ f •L ⎠⎝ VIN ⎠ Where ΔIL = inductor ripple current, f = operating frequency and L = inductor value. A trade-off between component size, efficiency and operating frequency can be seen from this equation. Accepting larger values of ΔIL allows the use of lower value inductors but results in greater inductor core loss, greater ESR loss in the output capacitor, and larger output voltage ripple. Generally, highest efficiency operation is obtained at low operating frequency with small ripple current. 3633a1f 12 LTC3633A/LTC3633A-1 APPLICATIONS INFORMATION A reasonable starting point is to choose a ripple current that is about 40% of IOUT(MAX). Note that the largest ripple current occurs at the highest VIN. Exceeding 60% of IOUT(MAX) is not recommended. To guarantee that ripple current does not exceed a specified maximum, the inductance should be chosen according to: ⎛ V ⎞⎛ ⎞ V OUT ⎟⎟ ⎜⎜1– OUT ⎟⎟ L = ⎜⎜ ⎝ f • ΔIL(MAX) ⎠ ⎝ VIN(MAX) ⎠ Once the value for L is known, the type of inductor must be selected. Actual core loss is independent of core size for a fixed inductor value, but is very dependent on the inductance selected. As the inductance increases, core losses decrease. Unfortunately, increased inductance requires more turns of wire, leading to increased DCR and copper loss. Ferrite designs exhibit very low core loss and are preferred at high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite core material saturates “hard”, which means that inductance collapses abruptly when the peak design current is exceeded. This results in an abrupt increase in inductor ripple current, so it is important to ensure that the core will not saturate. Different core materials and shapes will change the size/current and price/current relationship of an inductor. Toroid or shielded pot cores in ferrite or permalloy materials are small and don’t radiate much energy, but generally cost more than powdered iron core inductors with similar characteristics. The choice of which style inductor to use mainly depends on the price versus size requirements and any radiated field/EMI requirements. Table 1 gives a sampling of available surface mount inductors. Table 1. Inductor Selection Table INDUCTANCE DCR (μH) (mΩ) MAX DIMENSIONS CURRENT (mm) (A) Würth Electronik WE-HC 744312 Series 0.25 2.5 18 7 × 7.7 0.47 3.4 16 0.72 7.5 12 1.0 9.5 11 1.5 10.5 9 Vishay IHLP-2020BZ-01 Series 0.22 5.2 15 5.2 × 5.5 0.33 8.2 12 0.47 8.8 11.5 0.68 12.4 10 1 20 7 Toko FDV0620 Series 0.20 4.5 12.4 7 × 7.7 0.47 8.3 9.0 1.0 18.3 5.7 Coilcraft D01813H Series 0.33 4 10 6 × 8.9 0.56 10 7.7 1.2 17 5.3 TDK RLF7030 Series 1.0 8.8 6.4 6.9 × 7.3 1.5 9.6 6.1 HEIGHT (mm) 3.8 2 2.0 5.0 3.2 CIN and COUT Selection The input capacitance, CIN, is needed to filter the trapezoidal wave current at the drain of the top power MOSFET. To prevent large voltage transients from occurring, a low ESR input capacitor sized for the maximum RMS current is recommended. The maximum RMS current is given by: IRMS = IOUT(MAX) VOUT ( VIN − VOUT ) VIN This formula has a maximum at VIN = 2VOUT, where IRMS ≅ IOUT/2. This simple worst case condition is commonly used for design because even significant deviations do not offer much relief. Note that ripple current ratings from capacitor manufacturers are often based on only 2000 hours of life which makes it advisable to further derate the capacitor, or choose a capacitor rated at a higher temperature than required. 3633a1f 13 LTC3633A/LTC3633A-1 APPLICATIONS INFORMATION Several capacitors may also be paralleled to meet size or height requirements in the design. For low input voltage applications, sufficient bulk input capacitance is needed to minimize transient effects during output load changes. Even though the LTC3633A design includes an overvoltage protection circuit, care must always be taken to ensure input voltage transients do not pose an overvoltage hazard to the part. The selection of COUT is determined by the effective series resistance (ESR) that is required to minimize voltage ripple and load step transients as well as the amount of bulk capacitance that is necessary to ensure that the control loop is stable. Loop stability can be checked by viewing the load transient response. The output ripple, ΔVOUT, is approximated by: ⎛ ⎞ 1 ΔVOUT < ΔIL ⎜ESR + ⎟ 8 • f • COUT ⎠ ⎝ When using low-ESR ceramic capacitors, it is more useful to choose the output capacitor value to fulfill a charge storage requirement. During a load step, the output capacitor must instantaneously supply the current to support the load until the feedback loop raises the switch current enough to support the load. The time required for the feedback loop to respond is dependent on the compensation and the output capacitor size. Typically, 3 to 4 cycles are required to respond to a load step, but only in the first cycle does the output drop linearly. The output droop, VDROOP, is usually about 3 times the linear drop of the first cycle. Thus, a good place to start is with the output capacitor size of approximately: COUT ≈ 3 • ΔIOUT f • VDROOP Though this equation provides a good approximation, more capacitance may be required depending on the duty cycle and load step requirements. The actual VDROOP should be verified by applying a load step to the output. Using Ceramic Input and Output Capacitors Higher values, lower cost ceramic capacitors are available in small case sizes. Their high ripple current, high voltage rating and low ESR make them ideal for switching regulator applications. However, due to the self-resonant and high-Q characteristics of some types of ceramic capacitors, care must be taken when these capacitors are used at the input. When a ceramic capacitor is used at the input and the power is supplied by a wall adapter through long wires, a load step at the output can induce ringing at the VIN input. At best, this ringing can couple to the output and be mistaken as loop instability. At worst, a sudden inrush of current through the long wires can potentially cause a voltage spike at VIN large enough to damage the part. For a more detailed discussion, refer to Application Note 88. When choosing the input and output ceramic capacitors, choose the X5R and X7R dielectric formulations. These dielectrics have the best temperature and voltage characteristics of all the ceramics for a given value and size. INTVCC Regulator Bypass Capacitor An internal low dropout (LDO) regulator draws power from the VIN1 input and produces the 3.3V supply that powers the internal bias circuitry and drives the gate of the internal MOSFET switches. The INTVCC pin connects to the output of this regulator and must have a minimum of 1μF ceramic decoupling capacitance to ground. The decoupling capacitor should have low impedance electrical connections to the INTVCC and PGND pins to provide the transient currents required by the LTC3633A. This supply is intended only to supply additional DC load currents as desired and not intended to regulate large transient or AC behavior, as this may impact LTC3633A operation. Boost Capacitor The LTC3633A uses a “bootstrap” circuit to create a voltage rail above the applied input voltage VIN. Specifically, a boost capacitor, CBOOST, is charged to a voltage approximately equal to INTVCC each time the bottom power MOSFET is turned on. The charge on this capacitor is then used to supply the required transient current during the remainder of the switching cycle. When the top MOSFET is turned on, the BOOST pin voltage will be equal to approximately VIN + 3.3V. For most applications, a 0.1μF ceramic capacitor closely connected between the BOOST and SW pins will provide adequate performance. 3633a1f 14 LTC3633A/LTC3633A-1 APPLICATIONS INFORMATION Low Power 2.5V Linear Regulator Minimum Off-Time/On-Time Considerations The V2P5 pin can be used as a low power 2.5V regulated rail. This pin is the output of a 10mA linear regulator powered from the INTVCC pin. Note that the power from V2P5 eventually comes from VIN1 since the INTVCC power is supplied from VIN1. When using this output, this pin must be bypassed with a 1μF ceramic capacitor. If this output is not being used, it is recommended to short this output to INTVCC to disable the regulator. The minimum off-time is the smallest amount of time that the LTC3633A can turn on the bottom power MOSFET, trip the current comparator and turn the power MOSFET back off. This time is typically 45ns. For the controlled on-time architecture, the minimum off-time limit imposes a maximum duty cycle of: Output Voltage Programming where f is the switching frequency, tDEAD is the nonoverlap time, or “dead time” (typically 10ns), and tOFF(MIN) is the minimum off-time. If the maximum duty cycle is surpassed, due to a dropping input voltage for example, the output will drop out of regulation. The minimum input voltage to avoid this dropout condition is: Each regulator’s output voltage is set by an external resistive divider according to the following equation: ⎛ R2 ⎞ VOUT = 0.6V ⎜1+ ⎟ ⎝ R1 ⎠ The desired output voltage is set by appropriate selection of resistors R1 and R2 as shown in Figure 2. Choosing large values for R1 and R2 will result in improved zeroload efficiency but may lead to undesirable noise coupling or phase margin reduction due to stray capacitances at the VFB node. Care should be taken to route the VFB trace away from any noise source, such as the SW trace. To improve the frequency response of the main control loop, a feedforward capacitor, CF , may be used as shown in Figure 2. Connecting the VON pin to the output voltage makes the on-time proportional the output voltage and allows the internal on-time servo loop to lock the converter’s switching frequency to the programmed value. If the output voltage is outside the VON sense range (0.6V – 6V for LTC3633A, 1.5V – 12V for LTC3633A-1), the output voltage will stay in regulation, but the switching frequency may deviate from the programmed frequency. VOUT R2 CF FB LTC3633A SGND R1 DC(MAX) = 1– f • ( tOFF(MIN) + 2 • tDEAD ) VIN(MIN) = VOUT 1− f • ( tOFF(MIN) + 2 • tDEAD ) Conversely, the minimum on-time is the smallest duration of time in which the top power MOSFET can be in its “on” state. This time is typically 20ns. In continuous mode operation, the minimum on-time limit imposes a minimum duty cycle of: DC(MIN) = ( f • tON(MIN) ) where tON(MIN) is the minimum on-time. As the equation shows, reducing the operating frequency will alleviate the minimum duty cycle constraint. In the rare cases where the minimum duty cycle is surpassed, the output voltage will still remain in regulation, but the switching frequency will decrease from its programmed value. This constraint may not be of critical importance in most cases, so high switching frequencies may be used in the design without any fear of severe consequences. As the sections on Inductor and Capacitor selection show, high switching frequencies allow the use of smaller board components, thus reducing the footprint of the application circuit. 3633a F02 Figure 2. Setting the Output Voltage 3633a1f 15 LTC3633A/LTC3633A-1 APPLICATIONS INFORMATION Internal/External Loop Compensation The LTC3633A provides the option to use a fixed internal loop compensation network to reduce both the required external component count and design time. The internal loop compensation network can be selected by connecting the ITH pin to the INTVCC pin. To ensure stability it is recommended that internal compensation only be used with applications with fSW > 1MHz. Alternatively, the user may choose specific external loop compensation components to optimize the main control loop transient response as desired. External loop compensation is chosen by simply connecting the desired network to the ITH pin. Suggested compensation component values are shown in Figure 3. For a 2MHz application, an R-C network of 220pF and 13kΩ provides a good starting point. The bandwidth of the loop increases with decreasing C. If R is increased by the same factor that C is decreased, the zero frequency will be kept the same, thereby keeping the phase the same in the most critical frequency range of the feedback loop. A 10pF bypass capacitor on the ITH pin is recommended for the purposes of filtering out high frequency coupling from stray board capacitance. In addition, a feedforward capacitor CF can be added to improve the high frequency response, as previously shown in Figure 2. Capacitor CF provides phase lead by creating a high frequency zero with R2 which improves the phase margin. ITH RCOMP 13k CCOMP 220pF LTC3633A SGND 3633a F03 Figure 3. Compensation Component Checking Transient Response The regulator loop response can be checked by observing the response of the system to a load step. When configured for external compensation, the availability of the ITH pin not only allows optimization of the control loop behavior but also provides a DC-coupled and AC filtered closed loop response test point. The DC step, rise time, and settling behavior at this test point reflect the closed loop response. Assuming a predominantly second order system, phase margin and/or damping factor can be estimated using the percentage of overshoot seen at this pin. The ITH external components shown in Figure 3 circuit will provide an adequate starting point for most applications. The series R-C filter sets the dominant pole-zero loop compensation. The values can be modified slightly (from 0.5 to 2 times their suggested values) to optimize transient response once the final PC layout is done and the particular output capacitor type and value have been determined. The output capacitors need to be selected because their various types and values determine the loop gain and phase. An output current pulse of 20% to 100% of full load current having a rise time of ~1μs will produce output voltage and ITH pin waveforms that will give a sense of the overall loop stability without breaking the feedback loop. Switching regulators take several cycles to respond to a step in load current. When a load step occurs, VOUT immediately shifts by an amount equal to ΔILOAD • ESR, where ESR is the effective series resistance of COUT. ΔILOAD also begins to charge or discharge COUT generating a feedback error signal used by the regulator to return VOUT to its steady-state value. During this recovery time, VOUT can be monitored for overshoot or ringing that would indicate a stability problem. When observing the response of VOUT to a load step, the initial output voltage step may not be within the bandwidth of the feedback loop, so the standard second order overshoot/DC ratio cannot be used to determine phase margin. The output voltage settling behavior is related to the stability of the closed-loop system and will demonstrate the actual overall supply performance. For a detailed explanation of optimizing the compensation components, including a review of control loop theory, refer to Linear Technology Application Note 76. In some applications, a more severe transient can be caused by switching in loads with large (>10μF) input capacitors. The discharged input capacitors are effectively put in parallel with COUT, causing a rapid drop in VOUT. No regulator can deliver enough current to prevent this problem, if the switch connecting the load has low resistance and is driven quickly. The solution is to limit the turn-on speed of the load switch driver. A hot swap controller is designed specifically 3633a1f 16 LTC3633A/LTC3633A-1 APPLICATIONS INFORMATION for this purpose and usually incorporates current limiting, short-circuit protection, and soft starting. MODE/SYNC Operation The MODE/SYNC pin is a multipurpose pin allowing both mode selection and operating frequency synchronization. Floating this pin or connecting it to INTVCC enables Burst Mode operation for superior efficiency at low load currents at the expense of slightly higher output voltage ripple. When the MODE/SYNC pin is tied to ground, forced continuous mode operation is selected, creating the lowest fixed output ripple at the expense of light load efficiency. The LTC3633A will detect the presence of the external clock signal on the MODE/SYNC pin and synchronize the internal oscillator to the phase and frequency of the incoming clock. The presence of an external clock will place both regulators into forced continuous mode operation. Output Voltage Tracking and Soft-Start The LTC3633A allows the user to control the output voltage ramp rate by means of the TRACKSS pin. From 0 to 0.6V, the TRACKSS voltage will override the internal 0.6V reference input to the error amplifier, thus regulating the feedback voltage to that of the TRACKSS pin. When TRACKSS is above 0.6V, tracking is disabled and the feedback voltage will regulate to the internal reference voltage. The voltage at the TRACKSS pin may be driven from an external source, or alternatively, the user may leverage the internal 1.4μA pull-up current source to implement a soft-start function by connecting an external capacitor (CSS) from the TRACKSS pin to ground. The relationship between output rise time and TRACKSS capacitance is given by: tSS = 430000Ω • CSS A default internal soft-start ramp forces a minimum softstart time of 400μs by overriding the TRACKSS pin input during this time period. Hence, capacitance values less than approximately 1000pF will not significantly affect soft-start behavior. When driving the TRACKSS pin from another source, each channel’s output can be set up to either coincidentally or ratiometrically track another supply’s output, as shown in Figure 4. In the following discussions, VOUT1 refers to the LTC3633A output 1 as a master channel and VOUT2 refers to output 2 as a slave channel. In practice, either channel can be used as the master. To implement the coincident tracking in Figure 4a, connect an additional resistive divider to VOUT1 and connect its midpoint to the TRACKSS pin of the slave channel. The ratio of this divider should be the same as that of the slave channel’s feedback divider shown in Figure 5a. In VOUT2 TIME VOUT1 OUTPUT VOLTAGE OUTPUT VOLTAGE VOUT1 VOUT2 TIME 3633a F04a (4a) Coincident Tracking 3633a F04b (4b) Ratiometric Tracking Figure 4. Two Different Modes of Output Voltage Tracking 3633a1f 17 LTC3633A/LTC3633A-1 APPLICATIONS INFORMATION this tracking mode, VOUT1 must be set higher than VOUT2. To implement the ratiometric tracking, the feedback pin of the master channel should connect to the TRACKSS pin of the slave channel (as in Figure 5b). By selecting different resistors, the LTC3633A can achieve different modes of tracking including the two in Figure 4. Upon start-up, the regulator defaults to Burst Mode operation until the output exceeds 80% of its final value (VFB > 0.48V). Once the output reaches this voltage, the operating mode of the regulator switches to the mode selected by the MODE/SYNC pin as described above. During normal operation, if the output drops below 10% of its final value (as it may when tracking down, for instance), the regulator will automatically switch to Burst Mode operation to prevent inductor saturation and improve TRACKSS pin accuracy. Output Power Good The PGOOD output of the LTC3633A is driven by a 20Ω (typical) open-drain pull-down device. This device will be turned off once the output voltage is within 5% (typical) of the target regulation point, allowing the voltage at PGOOD to rise via an external pull-up resistor. If the output voltage exits an 8% (typical) regulation window around the target regulation point, the open-drain output will pull down VOUT1 VOUT2 R3 R1 TO TRACKSS2 PIN R2 NOMINAL OUTPUT PGOOD VOLTAGE –8% R4 0% 5% 8% OUTPUT VOLTAGE Figure 6. PGOOD Pin Behavior A filter time of 40μs (typical) acts to prevent unwanted PGOOD output changes during VOUT transient events. As a result, the output voltage must be within the target regulation window of 5% for 40μs before the PGOOD pin pulls high. Conversely, the output voltage must exit the 8% regulation window for 40μs before the PGOOD pin pulls to ground. Efficiency Considerations The percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine VOUT1 VOUT2 R1 TO TRACKSS2 PIN TO VFB2 PIN –5% 3633a F06 R3 TO VFB1 PIN R4 with 20Ω output resistance to ground, thus dropping the PGOOD pin voltage. This behavior is described in Figure 6. R2 R3 TO VFB1 PIN TO VFB2 PIN R4 3633a F05 (5a) Coincident Tracking Setup (5b) Ratiometric Tracking Setup Figure 5. Setup for Coincident and Ratiometric Tracking 3633a1f 18 LTC3633A/LTC3633A-1 APPLICATIONS INFORMATION what is limiting the efficiency and which change would produce the most improvement. Percent efficiency can be expressed as: % Efficiency = 100% – (L1 + L2 + L3 +…) where L1, L2, etc. are the individual losses as a percentage of input power. Although all dissipative elements in the circuit produce losses, three main sources usually account for most of the losses in LTC3633A circuits: 1) I2R losses, 2) switching losses and quiescent power loss 3) transition losses and other losses. 1. I2R losses are calculated from the DC resistances of the internal switches, RSW, and external inductor, RL. In continuous mode, the average output current flows through inductor L but is “chopped” between the internal top and bottom power MOSFETs. Thus, the series resistance looking into the SW pin is a function of both top and bottom MOSFET RDS(ON) and the duty cycle (DC) as follows: RSW = (RDS(ON)TOP)(DC) + (RDS(ON)BOT)(1 – DC) The RDS(ON) for both the top and bottom MOSFETs can be obtained from the Typical Performance Characteristics curves. Thus to obtain I2R losses: I2R losses = IOUT2(RSW + RL) 2. The internal LDO supplies the power to the INTVCC rail. The total power loss here is the sum of the switching losses and quiescent current losses from the control circuitry. Each time a power MOSFET gate is switched from low to high to low again, a packet of charge dQ moves from VIN to ground. The resulting dQ/dt is a current out of INTVCC that is typically much larger than the DC control bias current. In continuous mode, IGATECHG = f(QT + QB), where QT and QB are the gate charges of the internal top and bottom power MOSFETs and f is the switching frequency. For estimation purposes, (QT + QB) on each LTC3633A regulator channel is approximately 2.3nC. To calculate the total power loss from the LDO load, simply add the gate charge current and quiescent current and multiply by VIN: PLDO = (IGATECHG + IQ) • VIN 3. Other “hidden” losses such as transition loss, copper trace resistances, and internal load currents can account for additional efficiency degradations in the overall power system. Transition loss arises from the brief amount of time the top power MOSFET spends in the saturated region during switch node transitions. The LTC3633A internal power devices switch quickly enough that these losses are not significant compared to other sources. Other losses, including diode conduction losses during dead-time and inductor core losses, generally account for less than 2% total additional loss. Thermal Considerations The LTC3633A requires the exposed package backplane metal (PGND) to be well soldered to the PC board to provide good thermal contact. This gives the QFN and TSSOP packages exceptional thermal properties, which are necessary to prevent excessive self-heating of the part in normal operation. In a majority of applications, the LTC3633A does not dissipate much heat due to its high efficiency and low thermal resistance of its exposed-back QFN package. However, in applications where the LTC3633A is running at high ambient temperature, high VIN, high switching frequency, and maximum output current load, the heat dissipated may exceed the maximum junction temperature of the part. If the junction temperature reaches approximately 150°C, both power switches will be turned off until temperature returns to 140°C. To prevent the LTC3633A from exceeding the maximum junction temperature of 125°C, the user will need to do some thermal analysis. The goal of the thermal analysis 3633a1f 19 LTC3633A/LTC3633A-1 APPLICATIONS INFORMATION TRISE = PD • θJA As an example, consider the case when one of the regulators is used in an application where VIN = 12V, IOUT = 2A, frequency = 2MHz, VOUT = 1.8V. From the RDS(ON) graphs in the Typical Performance Characteristics section, the top switch on-resistance is nominally 145mΩ and the bottom switch on-resistance is nominally 70mΩ at 70°C ambient. The equivalent power MOSFET resistance RSW is: RDS(ON)TOP • 1.8V 10.2V +RDS(ON)BOT • = 81.3mΩ 12V 12V From the previous section’s discussion on gate drive, we estimate the total gate drive current through the LDO to be 2MHz • 2.3nC = 4.6mA, and IQ of one channel is 0.65mA (see Electrical Characteristics). Therefore, the total power dissipated by a single regulator is: PD = IOUT2 • RSW + VIN • (IGATECHG + IQ) PD = (2A)2 • (0.0813Ω) + (12V) • (4.6mA + 0.65mA) = 0.388W Running two regulators under the same conditions would result in a power dissipation of 0.776W. The QFN 5mm × 4mm package junction-to-ambient thermal resistance, θJA, is around 43°C/W. Therefore, the junction temperature of the regulator operating in a 70°C ambient temperature is approximately: TJ = 0.776W • 43°C/W + 70°C = 103°C which is below the maximum junction temperature of 125°C. With higher ambient temperatures, a heat sink or cooling fan should be considered to drop the junction-to-ambient thermal resistance. Alternatively, the TSSOP package may be a better choice for high power applications, since it has better thermal properties than the QFN package. Remembering that the above junction temperature is obtained from an RDS(ON) at 70°C, we might recalculate the junction temperature based on a higher RDS(ON) since it increases with temperature. Redoing the calculation assuming that RSW increased 12% at 103°C yields a new junction temperature of 107°C. If the application calls for a higher ambient temperature and/or higher load currents, care should be taken to reduce the temperature rise of the part by using a heat sink or air flow. Figure 7 is a temperature derating curve based on the demo board (QFN package). It can be used to estimate the maximum allowable ambient temperature for given DC load currents in order to avoid exceeding the maximum operating junction temperature of 125°C. 3.5 CHANNEL 1 LOAD CURRENT (A) is to determine whether the power dissipated exceeds the maximum junction temperature of the part. The temperature rise is given by: 3.0 2.5 2.0 1.5 1.0 CH2 LOAD = 0A CH2 LOAD = 1A CH2 LOAD = 2A CH2 LOAD = 3A 0.5 0 0 25 75 100 50 MAXIMUM ALLOWABLE AMBIENT TEMPERATURE (°C) 125 3633 F07 Figure 7. Temperature Derating Curve for DC1347 Demo Circuit Junction Temperature Measurement The junction-to-ambient thermal resistance will vary depending on the size and amount of heat sinking copper on the PCB board where the part is mounted, as well as the amount of air flow on the device. In order to properly evaluate this thermal resistance, the junction temperature needs to be measured. A clever way to measure the junction temperature directly is to use the internal junction diode on one of the pins (PGOOD) to measure its diode voltage change based on ambient temperature change. First remove any external passive component on the PGOOD pin, then pull out 100μA from the PGOOD pin to turn on its internal junction diode and bias the PGOOD pin to a negative voltage. With no output current load, measure the PGOOD voltage at an ambient temperature of 25°C, 75°C and 125°C to establish a slope relationship between the delta voltage on PGOOD and delta ambient temperature. Once this slope is established, then the junction temperature rise can be measured as a function 3633a1f 20 LTC3633A/LTC3633A-1 APPLICATIONS INFORMATION of power loss in the package with corresponding output load current. Although making this measurement with this method does violate absolute maximum voltage ratings on the PGOOD pin, the applied power is so low that there should be no significant risk of damaging the device. 6) Flood all unused areas on all layers with copper in order to reduce the temperature rise of power components. These copper areas should be connected to the exposed backside of the package (PGND). Board Layout Considerations Design Example When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the LTC3633A. Check the following in your layout: As a design example, consider using the LTC3633A in an application with the following specifications: VIN(MAX) = 13.2V, VOUT1 = 1.8V, VOUT2 = 3.3V, IOUT(MAX) = 3A, IOUT(MIN) = 10mA, f = 2MHz, VDROOP ~ (5% • VOUT). The following discussion will use equations from the previous sections. 1) Do the input capacitors connect to the VIN and PGND pins as close as possible? These capacitors provide the AC current to the internal power MOSFETs and their drivers. 2) The output capacitor, COUT, and inductor L should be closely connected to minimize loss. The (–) plate of COUT should be closely connected to both PGND and the (–) plate of CIN. 3) The resistive divider, (e.g. R1 to R4 in Figure 8) must be connected between the (+) plate of COUT and a ground line terminated near SGND. The feedback signal VFB should be routed away from noisy components and traces, such as the SW line, and its trace length should be minimized. In addition, the RT resistor and loop compensation components should be terminated to SGND. 4) Keep sensitive components away from the SW pin. The RT resistor, the compensation components, the feedback resistors, and the INTVCC bypass capacitor should all be routed away from the SW trace and the inductor L. 5) A ground plane is preferred, but if not available, the signal and power grounds should be segregated with both connecting to a common, low noise reference point. The connection to the PGND pin should be made with a minimal resistance trace from the reference point. Refer to Figures 9 and 10 for board layout examples. Because efficiency is important at both high and low load current, Burst Mode operation will be utilized. First, the correct RT resistor value for 2MHz switching frequency must be chosen. Based on the equation discussed earlier, RT should be 160k; the closest standard value is 162k. RT can be tied to INTVCC if switching frequency accuracy is not critical. Next, determine the channel 1 inductor value for about 40% ripple current at maximum VIN: ⎛ ⎞⎛ 1.8V 1.8V ⎞ L1= ⎜ ⎟ ⎜1− ⎟ = 0.64μH ⎝ 2MHz • 1.2A ⎠ ⎝ 13.2V ⎠ A standard value of 0.68μH should work well here. Solving the same equation for channel 2 results in a 1μH inductor. COUT will be selected based on the charge storage requirement. For a VDROOP of 90mV for a 3A load step: COUT1 ≈ 3 • ΔIOUT 3 • (3A) = = 50μF f • VDROOP (2MHz)(90mV) 3633a1f 21 LTC3633A/LTC3633A-1 APPLICATIONS INFORMATION A 47μF ceramic capacitor should be sufficient for channel 1. Solving the same equation for channel 2 (using 5% of VOUT for VDROOP) results in 27μF of capacitance (22μF is the closest standard value). Lastly, the feedback resistors must be chosen. Picking R1 and R3 to be 12.1k, R2 and R4 are calculated to be: ⎛ 1.8V ⎞ R2 = (12.1k) • ⎜ – 1⎟ = 24.2k ⎝ 0.6V ⎠ CIN should be sized for a maximum current rating of: IRMS = 3A 1.8V (13.2V − 1.8V ) 13.2V ⎛ 3.3V ⎞ R4 = (12.1k) • ⎜ – 1⎟ = 54.5k ⎝ 0.6V ⎠ = 1A The final circuit is shown in Figure 8. Solving this equation for channel 2 results in an RMS input current of 1.3A. Decoupling each VIN input with a 47μF ceramic capacitor should be adequate for most applications. VIN 12V CIN 47μF ×2 RUN1 RUN2 VIN2 VIN1 LTC3633A RT TRACKSS2 PGOOD2 BOOST2 R5 162k VOUT2 3.3V AT 3A COUT2 22μF L2 1μH INTVCC ITH1 ITH2 V2P5 MODE/SYNC PHMODE TRACKSS1 PGOOD1 BOOST1 0.1μF 0.1μF SW2 VON2 VFB2 R4 R3 54.9k 12.1k CVCC 2.2μF SGND PGND L1 0.68μH SW1 VON1 VFB1 R2 R1 12.1k 24.3k VOUT1 1.8V AT 3A COUT1 47μF 3633a F08 Figure 8. Design Example Circuit 3633a1f 22 LTC3633A/LTC3633A-1 APPLICATIONS INFORMATION VIA TO VON1/R2 (NOT SHOWN) VIA TO BOOST1 VOUT1 COUT1 L1 GND VIAS TO GROUND PLANE SW1 CIN CBOOST1 VIAS TO GROUND PLANE VIA TO GROUND PLANE CVCC VIN SGND (TO NONPOWER COMPONENTS) CBOOST2 CIN SW2 GND VIAS TO GROUND PLANE L2 COUT2 VOUT2 3633a F09 VIA TO BOOST2 VIA TO VON2/R4 (NOT SHOWN) Figure 9. Example of Power Component Layout for QFN Package VIA TO VON1 AND R2 (NOT SHOWN) COUT1 VOUT1 VIAS TO GROUND PLANE GND VIAS TO GROUND PLANE L1 CIN VIA TO BOOST1 SW1 CVCC CBOOST1 CBOOST2 SGND (TO NONPOWER COMPONENTS) VIA TO GROUND PLANE VIN SW2 VIA TO BOOST2 CIN L2 GND VIAS TO GROUND PLANE COUT2 VOUT2 3633a F10 VIA TO VON2 AND R4 (NOT SHOWN) Figure 10. Example of Power Component Layout for TSSOP Package 3633a1f 23 LTC3633A/LTC3633A-1 TYPICAL APPLICATIONS 1.8V/2.5V 4MHz Buck Regulator VIN 12V C1 22μF ×2 VIN2 RUN1 RUN2 ITH2 VIN1 C2 2.2μF V2P5 PHMODE ITH1 6.98k 10pF INTVCC 6.98k 220pF 10pF LTC3633A 220pF RT R5 80.6k VOUT2 2.5V AT 3A MODE/SYNC BOOST2 L2 0.82μH R4 31.6k L1 0.68μH 0.1μF SW2 VON2 VFB2 COUT2 22μF BOOST1 0.1μF R3 10k SGND PGND SW1 VON1 VFB1 R2 R1 12.1k 24.3k VOUT1 1.8V AT 3A COUT1 47μF 3633a TA02 3.3V/1.8V Sequenced Regulator with 6V Input UVLO (VOUT1 Enabled After VOUT2) VIN 6V TO 20V C1 47μF ×2 R7 154k R6 100k VIN2 RUN1 PGOOD2 VIN1 RUN2 LTC3633A R8 40k INTVCC ITH1 ITH2 V2P5 C2 2.2μF MODE/SYNC PHMODE RT R5 162k VOUT2 3.3V AT 3A COUT2 22μF L2 1μH BOOST2 0.1μF SW2 VON2 VFB2 R4 54.9k BOOST1 0.1μF R3 12.1k SGND PGND L1 0.68μH SW1 VON1 VFB1 R1 12.1k R2 24.3k VOUT1 1.8V AT 3A COUT1 47μF 3633a TA03 3633a1f 24 LTC3633A/LTC3633A-1 TYPICAL APPLICATIONS 1.2V/1.8V Buck Regulator with Coincident Tracking and 6V Input UVLO VIN 6V TO 20V R7 154k C1 47μF ×2 RUN1 RUN2 VIN2 R8 40k VIN1 INTVCC ITH1 ITH2 MODE/SYNC C2 2.2μF V2P5 LTC3633A PHMODE RT TRACKSS2 R5 196k L2 0.47μH VOUT2 1.2V AT 3A BOOST2 R4 10k L1 0.68μH 0.1μF SW2 VON2 VFB2 COUT2 68μF BOOST1 0.1μF R3 10k VOUT1 1.8V AT 3A SW1 VON1 VFB1 SGND PGND R1 10k R2 15k R6 4.99k COUT1 47μF 3633a TA04 1.5V 1MHz Dual Phase Buck Regulator VIN 3.6V TO 20V C1 22μF ×2 C2 2.2μF VIN1 VIN2 RUN1 BOOST1 RUN2 INTVCC BOOST2 V2P5 0.1μF 1μH LTC3633A PHMODE ITH1 ITH2 6.04k VOUT 1.5V AT 6A SW1 COUT 47μF ×2 0.1μF 1μH SW2 VON1 VON2 29.4k VFB1 1nF VFB2 RT 324k 19.6k MODE/SYNC SGND PGND 3633a TA06 3633a1f 25 LTC3633A/LTC3633A-1 PACKAGE DESCRIPTION Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. FE Package 28-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG # 05-08-1663 Rev I) Exposed Pad Variation EB 9.60 – 9.80* (.378 – .386) 4.75 (.187) 4.75 (.187) 28 27 26 2524 23 22 21 20 1918 17 16 15 6.60 ±0.10 4.50 ±0.10 2.74 (.108) SEE NOTE 4 0.45 ±0.05 EXPOSED PAD HEAT SINK ON BOTTOM OF PACKAGE 6.40 2.74 (.252) (.108) BSC 1.05 ±0.10 0.65 BSC RECOMMENDED SOLDER PAD LAYOUT 4.30 – 4.50* (.169 – .177) 0.09 – 0.20 (.0035 – .0079) 0.50 – 0.75 (.020 – .030) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS 2. DIMENSIONS ARE IN MILLIMETERS (INCHES) 3. DRAWING NOT TO SCALE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 0.25 REF 1.20 (.047) MAX 0° – 8° 0.65 (.0256) BSC 0.195 – 0.30 (.0077 – .0118) TYP 0.05 – 0.15 (.002 – .006) FE28 (EB) TSSOP REV I 0211 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE 3633a1f 26 LTC3633A/LTC3633A-1 PACKAGE DESCRIPTION Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. UFD Package 28-Lead Plastic QFN (4mm × 5mm) (Reference LTC DWG # 05-08-1712 Rev B) 0.70 ±0.05 4.50 ± 0.05 3.10 ± 0.05 2.50 REF 2.65 ± 0.05 3.65 ± 0.05 PACKAGE OUTLINE 0.25 ±0.05 0.50 BSC 3.50 REF 4.10 ± 0.05 5.50 ± 0.05 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 4.00 ± 0.10 (2 SIDES) 0.75 ± 0.05 R = 0.05 TYP PIN 1 NOTCH R = 0.20 OR 0.35 × 45° CHAMFER 2.50 REF R = 0.115 TYP 27 28 0.40 ± 0.10 PIN 1 TOP MARK (NOTE 6) 1 2 5.00 ± 0.10 (2 SIDES) 3.50 REF 3.65 ± 0.10 2.65 ± 0.10 (UFD28) QFN 0506 REV B 0.25 ± 0.05 0.200 REF 0.50 BSC 0.00 – 0.05 BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WXXX-X). 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3633a1f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 27 LTC3633A/LTC3633A-1 TYPICAL APPLICATION 3.3V/1.8V Buck Regulator with 2.5V LDO Output VIN 12V C1 47μF ×2 RUN1 RUN2 VIN2 VIN1 INTVCC ITH1 ITH2 C2 2.2μF PHMODE MODE/SYNC LTC3633A RT V2P5 R5 162k VOUT2 1.8V AT 3A L2 0.68μH 2.5V AT 10mA 1μF BOOST1 BOOST2 0.1μF 0.1μF SW2 VON2 VFB2 R4 COUT2 20k 47μF R3 10k SGND PGND L1 1μH SW1 VON1 VFB1 R1 10k R2 45.3k VOUT1 3.3V AT 3A COUT1 22μF 3633a TA07 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC3633 15V, Dual 3A (IOUT ), 4MHz Synchronous Step-Down DC/DC Converter 95% Efficiency, VIN: 3.6V to 15V, VOUT(MIN) = 0.6V, IQ = 500μA, ISD < 13μA, 4mm × 5mm QFN-28, TSSOP-28E LTC3605 15V, 5A (IOUT ), 4MHz, Synchronous Step-Down DC/DC Converter 95% Efficiency, VIN: 4V to 15V, VOUT(MIN) = 0.6V, IQ = 2mA, ISD < 15μA, 4mm × 4mm QFN-24 LTC3603 15V, 2.5A (IOUT ), 3MHz, Synchronous Step-Down DC/DC Converter 95% Efficiency, VIN: 4.5V to 15V, VOUT(MIN) = 0.6V, IQ = 75μA, ISD < 1μA, 4mm × 4mm QFN-20, MSOP-16E LTC3602 10V, 2.5A (IOUT ), 3MHz, Synchronous Step-Down DC/DC Converter 95% Efficiency, VIN: 4.5V to 10V, VOUT(MIN) = 0.6V, IQ = 75μA, ISD < 1μA, 3mm × 3mm QFN-16, MSOP-16E LTC3601 15V, 1.5A (IOUT ), 4MHz, Synchronous Step-Down DC/DC Converter 95% Efficiency, VIN: 4.5V to 15V, VOUT(MIN) = 0.6V, IQ = 300μA, ISD < 1μA, 4mm × 4mm QFN-20, MSOP-16E LTC3605A 20V, 5A (IOUT ), 4MHz, Synchronous Step-Down DC/DC Converter 95% Efficiency, VIN: 4V to 20V, VOUT(MIN) = 0.6V, IQ = 2mA, ISD < 15μA, 4mm × 4mm QFN-24 LTC3604 15V, 2.5A (IOUT ), 4MHz, Synchronous Step-Down DC/DC Converter 95% Efficiency, VIN: 3.6V to 15V, VOUT(MIN) = 0.6V, IQ = 300μA, ISD < 15μA, 3mm × 3mm QFN-16, MSOP-16E LT3626 20V, 2.5A Synchronous Monolithic Step-Down Regulator with Current and Temperature Monitoring 95% Efficiency, VIN: 3.6V to 20V, VOUT(MIN) = 0.6V, IQ = 300μA, ISD < 15μA, 3mm × 4mm QFN-20 3633a1f 28 Linear Technology Corporation LT 0912 • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2012