ALUMINUM ELECTROLYTIC CAPACITORS WX 5.5mmL Chip Type series Chip type with 5.5mm height. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Load life of 2000 hours at 85°C. WT Compliant to the RoHS directive (2011/65/EU). WJ High Temperature High Te m p reflow WX WP Bi-polarized Smaller Specifications ZS Item Performance Characteristics Category Temperature Range – 40 to +85°C Rated Voltage Range 4 to 50V Rated Capacitance Range 0.1 to 330µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) ,whichever is greater. Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) Rated voltage (V) tan δ (MAX.) 4 6.3 10 16 25 35 50 0.35 (0.40) 0.26 (0.30) 0.20 (0.24) 0.16 (0.19) 0.14 (0.16) 0.12 (0.14) 0.12 (0.14) Values in ( ) applicable to WR, φ3 case size. Measurement frequency : 120Hz 4 7 15 Rated voltage (V) Z– 25°C / Z+20°C Z– 40°C / Z+20°C Stability at Low Temperature Impedance ratio ZT / Z20 (MAX.) 6.3 4 8 10 3 8 16 2 4 25 2 4 35 2 3 50 2 3 Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 85°C. Shelf Life After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20°C. Marking Black print on the case top. Chip Type Within ±10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value Type numbering system (Example : 16V 10µF) 0.5 MAX. B±0.2 C±0.2 5.4 1 +0.1 –0.2 2 3 4 5 6 7 8 9 10 11 12 13 14 UWX 1 C 1 0 0 MC L 1 G B Taping code A±0.2 A±0.2 Plastic platform 0.3 MAX. E 1 Voltage φD±0.5 A2 10 16V Capacitance change tan δ Leakage current Positive Capacitance 2 Lot No. Within ±20% of the initial capacitance value (Within ±25% for 4 V and φ3,WR series units) 200% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage Current Size code Configuration Capacitance tolerance (±20%) Rated capacitance (10µF) Negative 0.5 to 0.8 φD A B C E 3 1.5 3.3 3.3 0.8 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 (mm) 6.3 8 2.4 3.3 6.6 8.3 6.6 8.3 2.2 2.3 φD Code 3 2 4 to 8 1 Rated voltage (16V) Series name Type • In the case of size φ3 in ( ),parentheses, use WX in the 2nd and 3rd digit and put a 2 in the 12th digit of type numbering system. 1. Voltage mark for 6.3V is 6V . In case of marking for φ3 units, “V” for rated voltage is omitted. 2. In case of marking for φ3 units, Lot No.is expressed by a digit (month code). Dimension table in next page. CAT.8100C ALUMINUM ELECTROLYTIC CAPACITORS WX series Dimensions 4 0G V Cap. (µF) Code 6.3 0J 10 1A 16 1C 25 1E 35 1V 0.1 0R1 4 (3) 1.0 0.22 R22 4 (3) 2.0 0.33 R33 4 (3) 2.8 0.47 R47 4 (3) 4.0 1 010 4 (3) 2.2 2R2 3.3 3R3 4.7 4R7 3 3 10 4 17 16 (12) 4 18 5 20 (18) 5 27 (24) 5 29 (24) 6.3 33 (30) 33 (30) 5 37 (30) 6.3 42 (38) 6.3 46 (39) 8 52 (43) 5 41 (34) 6.3 49 (44) 6.3 52 (46) 8 62 (53) 8 71 45 (40) 6.3 52 (47) 6.3 58 (52) 8 70 (60) 8 80 22 220 3 019 4 (3) 28 (21) 5 33 330 4 028 5 37 (34) 47 470 4 033 5 56 560 5 042 6.3 52 (46) 6.3 57 (50) 6.3 63 (57) 8 100 101 5 056 6.3 70 (47) 6.3 76 (54) 6.3 86 8 150 151 6.3 079 6.3 220 221 6.3 096 8 110 (74) 330 331 8 145 8 170 71 8 111 (76) 8 135 76 (65) 110 ),parentheses, use WX at 2nd and 3rd digit and put 2 at the 12th digit of type numbering system. } 8.4 (8.0) 13 (10) 23 (18) 100 Size φ4 is available for capacitors marked. " " Size φ5 is available for capacitors marked. " " Size φ6.3 is available for capacitors marked. " " 4 (3) 4 (3) 10 In the case of size φ3 in ( 8.4 4 (3) ( ) is also available with φ3mm upon request. • 50 1H Case size Rated φ D (mm) ripple Rated ripple current (mArms) at 85°C 120Hz ( ) = φ3 units and WR Series In such a case, W R will be put at 2nd and 3rd digit of type numbering system. Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UR(p.154), UG(p.162) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100C