UX - Nichicon

ALUMINUM ELECTROLYTIC CAPACITORS
UX
Chip Type, Wide Temperature Range
series
Chip type, operating over wide temperature
range of to -55 to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
UJ
UB
LR
High
Temperature
High
Voltage
UX
Extended
range
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +105°C (6.3 to 100V), –40 to +105°C (160 to 400V)
Rated Voltage Range
6.3 to 400V
Rated Capacitance Range
1 to 1000µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
Rated voltage (V)
6.3 to 100
160 to 400
Leakage Current
After 1 minute's application of rated voltage, leakage current is not more than 0.03CV (µA).
I = 0.04CV+100 ( µA) max.(1 minute's)
Measurement frequency : 120Hz at 20°C
Tangent of loss angle (tan δ)
Rated voltage (V)
tan δ (MAX.)
6.3
0.22
10
0.19
16
0.16
25
0.14
35
0.12
50
0.10
63
0.10
100
0.08
160
0.20
200
0.20
250
0.20
400
0.25
Measurement frequency: 120Hz
Stability at Low Temperature
Rated voltage (V)
Impedance ratio
ZT / Z20 (MAX.)
Z–55°C / Z+20°C
Z–40°C / Z+20°C
6.3
4
10
4
—
—
16
3
25
3
35
3
50
2
63
3
100
4
—
—
—
—
—
—
Capacitance change
tan δ
Leakage current
160
200
250
—
—
—
400
—
6
6
6
10
Within ±20% of the initial capacitance value
200% or less than the intial specified value
Less than or equal to the initial specified value
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours (160 to 400V : 3000hours) at 105°C.
Shelf Life
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds,
which is maintained at 250°C. The capacitors shall meet
the characteristic requirements listed at right when they are
removed from the plate and restored to 20°C.
Resistance to soldering
heat
Marking
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Black print on the case top.
Chip Type
Type numbering system (Example : 10V 100µF)
1
Plastic platform
0.3MAX.
C±0.2
H
L±0.3
H
1 Size φ8×6.2 only
2 Voltage mark for 6.3V is 6V .
C±0.2
Plastic platform
0.3MAX.
C±0.2
L±0.5
Lot No.
Capacitance
B±0.2
φD±0.5
Pressure relief vent
H
L±0.5
Pressure relief vent
7
8
9
10 11 12 13 14
H
A±0.2
A±0.2
A±0.2
Rated capacitance (100µF)
Rated voltage (10V)
Series name
D×L
Code
6.3 × 7.7 CL
8 × 6.2 CL
8 × 10
NL
10 × 10
NL
Type
φ D× L
E
Capacitance
6
Capacitance tolerance (±20%)
Negative
Positive
B±0.2
Lot No.
Trade mark
φD±0.5
A2P
100
16V
A2P
100
16V
2 Voltage
5
Size code
Negative
Positive
Plastic platform
0.3MAX.
105˚C
Marking
(φ8
× 10,
φ10 × 10)2 Voltage
105˚C Marking
Trade mark
4
Configuration
A±0.2
B±0.2
C±0.2
E
L±0.3
3
Package code
A±0.2 A±0.2
A±0.2 A±0.2
2 Voltage
mark for
6.3V is 6V .
Capacitance
Lot No.
Plastic platform
0.3MAX.
2
UUX 1 A 1 0 1 M C L 1GS
Positive
B±0.2
Capacitance
Lot No.
1
Trade mark
1 Size φ8×6.2 only
φD±0.5
A2P
100
10V
2 Voltage
A2P
100
10V
1
105˚C
Marking
Trade
mark
φD±0.5
2 Voltage
105˚C Marking
0.5MAX. 0.5MAX.
E
Positive
0.5MAX. 0.5MAX.
E
(φ6.3, φ8 × 6.2)
A
B
C
E
L
H
(mm)
6.3 × 7.7 8 × 6.2
8 × 10
10 × 10
2.4
3.3
2.9
3.2
6.6
8.3
8.3
10.3
6.6
8.3
8.3
10.3
2.2
2.3
3.1
4.5
7.7
6.2
10
10
0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1
Negative
Negative
Dimension table in next page.
CAT.8100D
ALUMINUM ELECTROLYTIC CAPACITORS
UX
series
Dimensions
Cap.
(μF)
4.7
6.3
0J
V
Code
4R7
10
1A
16
1C
10
100
22
220
33
330
47
470
100
101
220
221
330
331
470
471
173
8×10
288
10×10 318(296)
10×10 340(316) 10×10 351(326)
680
681
10×10
408
1000
102
10×10
495
25
1E
35
1V
63
1J
8×6.2
8×6.2 67(64)
8×6.2 76(75)
8×6.2
8×6.2
90
8×10 161(121)
8×10
10×10
160
2C
79(78)
8×10 148(111) 8×10
181
10×10 330(307) 10×10 351(283)
10×10 441(410) 10×10
372
250
2E
8×10
25
1.8
1R8
8×10
26
2.2
2R2
8×10
27
3.3
3R3
8×10
31
8×10
31
10×10
38
3.9
3R9
8×10
34
8×10
34
10×10
39
4.7
4R7
8×10
37
8×10
37
10×10
40
6.8
6R8
8×10
44
8×10
44
10×10
64
10×10
64
100
8×10
57
180
10×10
64
133
10×10
310
51
8×10
108
10×10 185(179)
8×10
10×10
220
10×10
320
75
10×10 150(121)
10×10
180
10×10
230
Case size
φD × L (mm)
Rated
ripple
450
400
2G
1
18
10×10
8×10
10×10 180(167)
100
2A
42
8×6.2
489
10×10
200
2D
10
124
10×10 304(283)
8×10
392
V
Code
010
Cap.
(μF)
50
1H
Rated ripple current (mArms) at 105°C 120Hz
Size φ6.3 × 7.7 is available for capacitors marked. " " / Size φ8 × 10 is available for capacitors marked. " "
In this case, 6 will be put at 12th digit of type numbering system.
Frequency coefficient of rated ripple current
Cap.(µF)
Frequency 0001 to 47V00
100 to 1000
50 Hz
0.80
0.85
120 Hz
1.00
1.00
300 Hz
1.15
1.08
1 kHz
1.40
1.20
10 kHz or more
1.67
1.30
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please select UJ(p.160) series if high C/V products are
reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100D