POWER LINE FILTER PBH Series 16/20A HIGH CURRENT, SNAP-IN/FLANGE MOUNT FILTER WITH IEC 60320 AC INLET SOCKET. MECHANICAL DIMENSIONS (Unit: mm) CASE F 42.0 35.0 52.8 42.0 30.1 R3 TYP. 27.0 2x 3.5 3.6 (79.5) 67.4 6.35 ✛ 0.8 34.0 26 CASE U FEATURES The PBH series offers filters for application that have high current (16/20A) requirements. The filters are available with different configurations of components and termination styles. These filters are available in flange mount and snap-in type. The medical grade filters offer excellent performance with maximum leakage current of 2µA at 120VAC, 60Hz. A ground choke can be added to enhance the grounding ability of the circuit. A bleeder resistor can also be added to prevent excessive voltages from developing across the filter capacitors when there is no load. 30.0 ✛ SEMKO, VDE approved to 16A * Medical application R3 TYP. 27.6 3.8 (79.5) 67.4 6.35 0.8 34.0 26.0 CASE O 2x 43.0+-- 0.1 34.5+ 0.5 6#32 10.0+-- 0.1 TECHNICAL DATA • Rated Voltage: 115/250VAC • Rated Current: 16A, 20A • Power Line Frequency: 50/60Hz • Max. Leakage Current each Line to Ground: @ 115VAC 60Hz: 0.25mA @ 250VAC 50Hz: 0.50mA @ 115VAC 60Hz: 2µA* @ 250VAC 50Hz: 5µA* • Hipot Rating (one minute) Line to Ground: 2250VDC Line to Line: 1450VDC • Temperature Range: -25C to +85C 27.0 SUGGESTED PANEL CUTOUT (MOUNTING FROM FRONT) THICKNESS OF PANEL IS FROM 1.00mm to 1.6mm APPLICATIONS Computer & networking equipment, Measuring & control equipment, Data processing equipment, laboratory instruments, Switching power supplies, other electronic equipment. 36.0 38.0 + 0.5 6.0 +-- 0.1 26.5-- 30.0 43.0 52.0 79.5 R3.0 2x 3.5 RECOMMENDED PANEL CUTOUT (MOUNTING FROM REAR) 75.7 0.8 6.35 34 26 Specifications subject to change without notice. Dimensions (mm). See Appendix A for recommended power cord. See PDI full line catalog for detailed specifications on power cords. 145 Algonquin Parkway, Whippany, NJ 07981 • 973-560-0019 • FAX: 973-560-0076 e-mail: [email protected] • www.powerdynamics.com 13 PBH Series Example & Ordering Code PBH 20 Q - 60 - 1 C U SCHEMATICS 1 LINE CURRENT RATING (A): = 16 = 20 R Cy CX L Cy N L' G' LOAD L mH L N' L mH G Lg TERMINAL: 3.0 -3.6L 4.0/0.187 6.6 UL 1015, 18AWG STRANDED, 4” QUICK CONNECT =Q SOLDER =S WIRE =W 2 L mH L Cy R L Cy N L' G' LOAD 2.0 -3.0L LINE 8.0 6.3/0.25 N' L mH G Lg GROUND CHOKE (100µH) COMPONENT LOCATIONS: 00 60 80 90 3 STANDARD TYPE WITHOUT C(X); C(Y) ONLY C(X) & C(Y) BEHIND L WITHOUT C(Y); C(X) ONLY WITHOUT C(Y); C(X) BEHIND L = = = = = 1 2✢ 3✢ 1M 2M✢ Cy 20A (mH) 0.5 0.5 0.5 1M =A =B =C L mH L R CX N' L mH G = M1 = M2 2M L mH FLANGE MOUNT SNAP-IN TABS - SIDE REAR PANEL MOUNT = F =U =O LINE L Comm. Mode(L-G) .15 .5 1 5 17 22 26 43 17 23 28 47 17 22 26 43 in MHz 10 30 51 43 57 45 51 43 Diff. Mode(L-L) .15 .5 1 5 8 18 24 45 8 18 23 51 18 28 33 46 14 N' L mH G' ✧ Insertion loss in dB (50 Ohm circuit) in MHz 10 30 43 35 54 34 53 35 This table applies to schematic 1 only. Visit our website or contact PDI for other schematic attenuation numbers. ❖ L' CX Lg Medical Applications Insertion loss in dB (50 Ohm circuit) Attenuation Code A B C L G Contact PDI for attenuation numbers ❖ R N ✢ Non-Medical Applications G' Lg 16/20A (mH) 0.5 0.5 CASE CODE: L' L N Cap. Cx (µF) 0.1 0.33 N' L mH MEDICAL SCHEMATICS Medical applications, select Attenuation code with corresponding component values from the table. Case Code F,O,U F,O,U L' G' Lg LINE Cap. Cy (pF) 2200 3300 2200 Cy CX L G Non-Medical applications, select Attenuation code with corresponding component values from the table. Cap. Cx (µF) 0.1 0.1 0.33 R N ATTENUATION CODE TABLE: Case Code F,O,U F,O,U F,O,U L mH L LOAD BLEEDER RESISTOR (1W, 1M) & GROUND CHOKE = = = = LOAD BLEEDER RESISTOR (1W, 1M) LOAD NO BLEEDER RESISTOR & NO GROUND CHOKE LINE OPTIONS: Attenuation Code M1 M2 Comm. Mode(L-G) .15 .5 1 5 16 21 22 24 16 20 22 24 in MHz 10 30 25 20 25 20 Diff. Mode(L-L) .15 .5 1 5 8 18 25 42 17 28 33 41 in MHz 10 30 43 30 40 31 ✧ This table applies to schematic 1M only. Visit our website or contact PDI for other schematic attenuation numbers. 145 Algonquin Parkway, Whippany, NJ 07981 • 973-560-0019 • FAX: 973-560-0076 e-mail: [email protected] • www.powerdynamics.com