SANYO LV8491CT

Ordering number : ENA1760
Bi-CMOS LSI
LV8491CT
Piezo Actuator Driver IC
Overview
The LV8491CT is a piezoelectric actuator driver IC. It internally generates drive waveforms and this makes it possible
to control piezoelectric actuators with simple instructions.
Features
• Actuators using piezoelectric elements can be driven and controlled simply by I2C communication.
• Multiple patterns of drive waveform conditions can be set for before and after performing normal operation when
executing the DRVPULSE instruction.
• The piezoelectric drive waveforms are set externally by serial input signals using the I2C interface.
The rising and falling timings are determined with clock count.
• Startup/stop of the IC is controlled by ENIN register input through I2C communication.
• The time for which the actuator is driven is determined with the drive frequency setting based on I2C communication.
• BUSY output can be used to identify the operation/stop state of the actuator while output is present at the OUT pin.
The BUSY signal can also be checked with the READ function controlled through I2C communication.
• Built-in undervoltage detection and protection circuit, and register power-on reset function.
Specifications
Absolute Maximum Ratings at Ta = 25°C, GND = 0V
Parameter
Symbol
Conditions
Ratings
Unit
Supply voltage
VCC max
-0.5 to 5.0
Output current
IO max
Peak output current 1
IO peak 1
t ≤ 1ms
750
mA
Peak output current 2
IO peak 2
t ≤ 10μs
1200
mA
Input signal voltage
VIN max
Allowable dissipation
Pd
Operating temperature
Topr
-30 to +85
°C
Storage temperature
Tstg
-55 to +125
°C
300
-0.5 to VCC+0.5
*Mounted on a specified board.
350
V
mA
V
mW
* Specified board : 40mm × 40mm × 1.6mm, glass epoxy board.
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment (home appliances, AV equipment,
communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be
intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace
instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety
equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case
of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee
thereof. If you should intend to use our products for applications outside the standard applications of our
customer who is considering such use and/or outside the scope of our intended standard applications, please
consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our
customer shall be solely responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer' s products or
equipment.
70710 SY PC 20100517-S00002 No.A1760-1/20
LV8491CT
Allowable Operating Conditions at Ta = 25°C, GND = 0V
Parameter
Symbol
Conditions
Ratings
Unit
Supply voltage
VCC
2.2 to 3.3
V
Input signal voltage
VIN
-0.3 to VCC
V
Corresponding CLK input frequency
Fclk
to 60
Maximum operating frequency
Ct max
MHz
Set STP count × 512
Times
Electrical Characteristics at Ta = 25°C, VCC = 2.8V, GND = 0V, unless otherwise specified.
Parameter
Symbol
Ratings
Conditions
min
Standby mode current drain
ICC0
No CLK input, When SCL/SDA = L
Operating mode current drain
ICC1
CLK = 10MHz, When SCL/SDA = H
Unit
typ
max
0.5
1.0
μA
1.0
mA
High-level input voltage
VIH
2.2V ≤ VCC ≤ 3.3V
SCL, SDA
1.4
VCC+0.3
V
Low-level input voltage
VIL
2.2V ≤ VCC ≤ 3.3V
SCL, SDA
-0.3
0.4
V
CLK pin high-level input voltage
VIH2
CLK
0.5×VCC
VCC+0.3
V
CLK pin low-level input voltage
VIL2
CLK
-0.3
0.2×VCC
V
BUSY pin high-level output voltage
BOH
With no load
VCC-0.15
VCC
V
BUSY pin low-level output voltage
BOL
With no load
0
0.15
V
BUSY pin leakage current
BLK
1.0
μA
BUSY pin sink current
Blsk
BUSY pin voltage when BUSY is set low =
1.5
2.2
mA
1.5
2.2
mA
1.8
2.0
2.2
V
2.8V
BUSY pin source current
Blso
BUSY pin voltage when BUSY is set high =
0V
Low voltage detection voltage
Vres
VCC voltage
Output block upper-side on
RonP
0.8
1.5
Ω
Output block lower-side on resistance
RonN
0.6
1.2
Ω
Turn on time
TPLH
With no load *1
0.15
μS
Turn off time
TPHL
With no load *1
0.1
μS
resistance
*1 : Rising time from 10 to 90% and falling time from 90 to 10% are specified with regard to the OUT pin voltage.
Package Dimensions
unit : mm (typ)
3399
0.33 MAX
5
3
0.4
2
1
0.285
0.08
SIDE VIEW
0.22
4
0.4
B
A
0.87
0.285
SANYO : WLP10(2.17X0.87)
Allowable power dissipation, Pd max – W
2.17
Pd max -- Ta
0.6
BOTTOM VIEW
SIDE VIEW
0.235
TOP VIEW
Specified board : 50×50×1.6mm3
glass epoxy
0.5
0.45
0.4
0.3
0.2
0.18
0.1
0
– 30 – 20
0
20
40
60
80
100
Ambient temperature, Ta – °C
No.A1760-2/20
LV8491CT
Pin Assignment
Ball side view
Top view
B
B
A
SCL
CLK
CLK
SCL
1
2
SDA
(NC)
(NC)
SDA
2
3
GND
BUSY
BUSY
GND
3
4
OUT1
VCC
VCC
OUT1
4
5
RFG
OUT2
OUT2
RFG
5
A
0.4
1
0.4
2.17
0.87
A1:SCL
A2:SDA
A3:GND
A4:OUT1
A5:RFG
B1:CLK
B2:(NC)
B3:BUSY
B4:VCC
B5:OUT2
No.A1760-3/20
LV8491CT
Block Diagram
VCC
OUT1
OUT2
RFG
Piezoelectric drive
waveform generation
register
Startup
control
block
Output control
BUSY
2-wire serial interface
GND
CLK
SCL
SDA
Value of the resistor connected to the RFG pin
Inrush current flowing to the piezoelectric elements can be controlled in the LV8491CT by inserting a resistor between
the RFG pin and GND potential.
Since the resistance affects the actuator operation, the constant must be determined in a range from 0 to 3.3Ω while
monitoring the operation of the actuator.
Capacitor on the VCC line
Piezoelectric actuators are capacitive loads in electrical terms, and they operate units by charging and discharging the
charges. Since the charge between the capacitor on the VCC line and piezoelectric elements is transferred, the capacitor
must be mounted near the VCC pin. The capacitance of the capacitor required is determined by the capacitance of the
piezoelectric element. A capacitance within a range that does not affect operation must be selected.
No.A1760-4/20
LV8491CT
Serial Bus Communication Specifications
I2C serial transfer timing conditions
twH
SCL
th1
twL
th2
tbuf
SDA
th1
ts2
ts1
ts3
Resend start condition
Start condition
ton
Stop condition
tof
Input waveform condition
Standard mode
Parameter
symbol
Conditions
min
typ
SCL clock frequency
Data setup time
ts1
Setup time of SCL with respect to the falling edge of SDA
4.7
ts2
Setup time of SDA with respect to the rising edge of SCL
250
ns
ts3
Setup time of SCL with respect to the rising edge of SDA
4.0
μs
μs
Pulse width
Input waveform conditions
Bus free time
100
unit
fscl
Data hold time
0
max
SCL clock frequency
kHz
μs
th1
Hold time of SCL with respect to the rising edge of SDA
4.0
th2
Hold time of SDA with respect to the falling edge of SCL
0.06
μs
twL
SCL low period pulse width
4.7
μs
twH
SCL high period pulse width
4.0
ton
SCL/SDA (input) rising time
1000
tof
SCL/SDA (input) falling time
300
tbuf
Interval between stop condition and start condition
μs
ns
ns
μs
4.7
High-speed mode
Parameter
Symbol
Conditions
min
typ
Clock frequency of SCL
Data setup time
ts1
Setup time of SCL with respect to the falling edge of SDA
0.6
ts2
Setup time of SDA with respect to the rising edge of SCL
100
ns
ts3
Setup time of SCL with respect to the rising edge of SDA
0.6
μs
μs
Pulse width
Input waveform conditions
Bus free time
400
unit
fscl
Data hold time
0
max
SCL clock frequency
kHz
μs
th1
Hold time of SCL with respect to the rising edge of SDA
0.6
th2
Hold time of SDA with respect to the falling edge of SCL
0.06
μs
twL
SCL low period pulse width
1.3
μs
twH
SCL high period pulse width
0.6
ton
SCL/SDA (input) rise time
300
ns
tof
SCL/SDA (input) fall time
300
ns
tbuf
Interval between the stop condition and the start condition
1.3
μs
μs
No.A1760-5/20
LV8491CT
2
I C bus transfer method
Start and stop conditions
The I2C bus requires that the state of SDA be preserved while SCL is high as shown in the timing diagram below during
a data transfer operation.
SCL
SDA
ts2
th2
When data is not being transferred, both SCL and SDA are in the high state. The start condition is generated and access is
started when SDA is changed from high to low while SCL and SDA are high.
Conversely, the stop condition is generated and access is ended when SDA is changed from low to high while SCL is
high.
Start condition
Stop condition
th1
th3
SCL
SDA
No.A1760-6/20
LV8491CT
Data transfer and acknowledgement response
After the start condition is generated, data is transferred one byte (8 bits) at a time. Any number of data bytes can be
transferred consecutively.
An ACK signal is sent to the sending side from the receiving side every time 8 bits of data are transferred. The
transmission of an ACK signal is performed by setting the receiving side SDA to low after SDA at the sending side is
released immediately after the clock pulse of SCL bit 8 in the data transferred has fallen low.
After the receiving side has sent the ACK signal, if the next byte transfer operation is to receive only the byte, the
receiving side releases SDA on the falling edge of the 9th clock of SCL.
There are no CE signals in the I2C bus ; instead, a 7-bit slave address is assigned to each device, and the first byte of the
transfer data is allocated to the 7-bit slave address and to the command (R/W) which specifies the direction of
subsequent data transfer.
The READ function of the LV8491CT provides only the functionality to test the BUSY state.
7-bit address data is transferred sequentially starting at the MSB and the second and subsequent bytes are written if the
state of the 8th bit is low and read if the state is high.
In the LV8491CT, the slave address is stipulated to be “1110010.”.
WRITE mode timing
Start
M
S
B
Slave address
L
S
B
W
A
C
K
M
S
B
Register address
L
S
B
A
C
K
M
S
B
L
S
B
Data
A
C
K
Stop
SCL
SDA
0
0 0
1
0
0
0
1 0
0 0
0
0
0
0
0 1
READ mode timing
Start
M
S
B
Slave address
L
S
B
R
A
C
K
M
S
B
L
S
B
Data
A
C
K
Stop
SCL
SDA
1
1 0
0
0
0
0
0 0
0
No.A1760-7/20
LV8491CT
Data transfer write format
The slave address and Write command must be allocated to the first byte and the register address in the serial map must
be designated in the second byte.
For the third byte, data transfer is carried out to the address designated by the register address which is written in the
second byte. Subsequently, if data continues, the register address value is automatically incremented for the fourth and
subsequent bytes.
Thus, continuous data transfer starting at the designated address is made possible.
After the register address reaches 1Fh, the transfer address for the next byte is set to 00h.
Data write example
S
1
1
1
0
0
1
0
0
A
Slave address
0
0
0
0
0
0
1
0
A
Data 1
Register address set to 02h
A
Write data to address 02h
R/W = 0 written
Data 2
A
Write data to address 03h
S
Start condition
Data 3
A
Data 4
Write data to address 04h
P
Stop condition
Master side transmission
A
A
P
Write data to address 05h
A
ACK signal
A
P
Slave side transmission
Data read example
S
1
1
1
0
0
1
0
1
A
Slave address
Data
Read data
R/W = 1 read
S
Start condition
Master side transmission
P
Notify end of read by not sending out ACK
Stop condition
A
A
ACK signal
Slave side transmission
No.A1760-8/20
LV8491CT
Serial Map
Register Address
Data
A7
A6
A5
A4
A3
A2
A1
A0
D7
0
0
0
0
0
0
0
0
M/I
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
1
D6
D5
D4
0
0
0
0
GATE
×
ENIN
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
1
0
0
3
0
0
0
0
0
1
0
0
0
0
0
0
1
1
0
0
0
0
0
0
1
1
1
6
7
0
0
0
0
1
0
0
0
8
0
0
0
0
1
0
0
1
9
0
0
0
0
1
0
1
0
10
0
0
0
0
0
0
0
0
0
0
0
0
0
0
RET [1 : 0]
INIT
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
GTBS [7 : 0]
0
STP [7 : 0]
0
0
0
0
×
×
×
×
0
0
0
0
×
×
0
0
0
0
×
×
0
0
×
×
0
0
×
0
0
0
1
0
1
1
×
0
0
0
0
0
0
1
1
0
0
×
×
0
0
12
0
CKSEL [1 : 0]
GTBR [7 : 0]
0
11
0
D0
GTAS [7 : 0]
1
5
D1
RST [7 : 0]
0
4
D2
DRVPULSE [6 : 0]
0
2
D3
0
INITMOV [7 : 4]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
NRPULSE1 [5 : 0]
0
0
NRP-A [5 : 0]
0
0
0
0
0
0
NRP-B [5 : 0]
0
0
NRP-C [5 : 0]
0
0
0
0
NRP-D [5 : 0]
0
0
0
0
0
0
0
0
1
1
0
1
×
×
NRPULSE2 [5 : 0]
0
0
0
0
1
1
1
0
×
×
NRP-E [5 : 0]
0
0
0
0
0
0
1
1
1
1
×
×
0
0
×
×
0
0
×
×
0
0
0
0
0
0
13
14
15
0
0
0
1
0
0
0
0
16
0
0
0
1
0
0
0
1
17
0
0
0
1
0
0
1
0
0
0
1
0
0
1
1
0
0
0
1
0
1
0
0
19
0
0
1
0
1
0
0
0
0
1
0
1
1
0
0
0
0
1
0
1
1
1
22
23
0
0
0
0
0
0
0
NRP-G [5 : 0]
0
0
NRP-H [5 : 0]
0
0
0
0
NR1GTBS [7 : 0]
0
0
0
0
NR2GTBR [7 : 0]
0
0
0
0
0
0
1
21
0
NR1GTBR [7 : 0]
0
20
0
NRP-F [5 : 0]
0
18
0
0
0
0
NR2GTBS [7 : 0]
0
0
NR3GTBR [7 : 0]
0
0
0
0
0
NR3GTBS [7 : 0]
0
0
0
0
0
Upper : Register name Lower : Default value
Continued on next page.
No.A1760-9/20
LV8491CT
Continued from preceding page.
Register Address
Data
A7
A6
A5
A4
A3
A2
A1
A0
0
0
0
1
1
0
0
0
0
0
0
1
1
0
0
1
D7
D6
0
0
1
1
0
1
0
0
1
1
0
0
0
0
0
0
0
1
0
0
0
D2
D1
D0
0
0
0
0
0
0
0
0
0
0
NR5GTBR [7 : 0]
0
1
0
NR5GTBS [7 : 0]
27
READ mode only register
0
0
0
26
0
D3
NR4GTBS [7 : 0]
25
0
D4
NR4GTBR [7 : 0]
24
0
D5
0
0
0
0
0
0
0
0
BUSY
×
×
×
×
×
×
×
0
0
0
0
0
0
0
0
28
Upper : Register name Lower : Default value
NR drive pulse output
Rise operation
DRVPULSE
communication input
Number of periods set by
NRPULSE1 + 1
BUSY output
OUT output
NR1
waveform
NR start waveform
(No GATE_B output generated)
One period
NR2
NR4
NR3
NRP-B
Number of
periods set by
NRP-A
NRP-C
NR5
Steady-state waveform
NRP-D
For example, when NRPULSE1 is set to 15, NRP-A to 3, NRP-B to 6, NRP-C to 9, and NRP-D to 12, one period of the
NR start waveform (no GATE_B output) is output, followed by three periods of the NR1 waveform, three periods of the
NR2 waveform, three periods of the NR3 waveform, three periods of the NR4 waveform, three periods of the NR5
waveform, and then STP x DRVPULSE periods of the steady-state waveform.
When NRPULSE1 is set to 0, no NR pulse is generated and the same output as the normal DRVPULSE input is generated.
In addition, when NRP-A and NRP-B are set the same value, the NR2 waveform is not output, and the NR3 waveform is
output following the NR1 waveform.
Fall operation
Number of periods set by
NRPULSE2
BUSY output
OUT output
Steady-state
waveform
NR5
NRP-E
NR4
NR3
NRP-F
NR2
NRP-G
NR1
NRP-H
The fall waveforms are output in order from the NR5 waveform to the NR1 waveform. The switching timing is set in the
same manner as that for rise operation.
No.A1760-10/20
LV8491CT
NR drive waveform settings
The settings are the same as those for the normal drive waveform. Drive waveforms are generated using the same
parameters as the normal waveform for RST and GTAS, and the NR waveform setting values for GTBR and GTBS.
Example: NR1 waveform
RST = Number of clock pulses per period - 1
The waveforms start after two clock pulses,
so Ta-1+2 = Ta+1.
GTAS=
Ta+1
Rises after two clock pulses from the reference.
NR1GTBR=
GTAS+off
NR1GTBS=
NR1GTBR+Tb
Waveform start
reference point
NR start waveform
NR waveform output control is as follows. When NRPULSE1 is set, a waveform without GATE_B output is output in the
first rise period. After that the waveforms set by NR are output in order from NR1.
When there are no NR settings for rise operation (when NRPULSE = 0), the NR start waveform is not output.
The same parameters as those of the normal waveform are referenced for RST and GTAS, and GTBR and GTBS are zero
input waveforms.
RST = Number of clock pulses per period - 1
GTAS=
Ta+1
The waveforms start after two clock pulses,
so Ta-1+2 = Ta+1.
Rises after two clock pulses after from the reference.
GATE_B is not output
Waveform start
reference point
No.A1760-11/20
LV8491CT
Serial Mode Settings
0
0
0
0
0
0
0
0
0
D7
D6
D5
D4
D3
D2
D1
D0
D0 to D6: DRVPULSE [6 : 0]
Operation count setting register. Specify a number from 0 to 127.
The number of cyclic operations determined by <DRVPLUSE setting> × <STP setting> are performed.
Additional data can be input and data is added up to the equivalent of total of 512 pulses.
However, when the EN pin is set low or ENIN is set to 0, the DRVPULSE counter is in the reset state, so
DRVPULSE input is not accepted.
Output operation is performed when DRVPULSE input is recognized, and OUT output starts according to
the waveform setting registers when the ACK signal is output after a 00h address instruction.
D7
Operation direction switching
*Default
Infinity distance direction
Macro direction
M/I
0
∞
1
macro
Operation direction switching register
The operation count setting register is reset when the register is switched. To stop the operation of the unit,
switch the M/I register and set DRVPULSE to 0 for input. This register is also used to set the direction of
operation when the initialization sequence is to be performed.
1
0
0
0
0
0
0
0
1
D7
0
D5
D4
D3
D2
D1
D0
D0: Register for selecting whether the initialization sequence is to be performed when the ENIN input changes
from 0 to 1.
D0
INIT
Initialization to be performed/not to be performed setting
0
Initialization to be performed
*Default
1
Initialization not to be performed
D2
D1
0
0
RET
2 times
0
1
1 time
1
0
3 times
1
1
4 times
D4
D3
0
0
CKSEL
1/4
0
1
1/2
1
0
1
1
1
1
Number of initialization sequence swing back
*Default
Input clock division ratio switching
*Default
1/4
1/2
1 (no frequency division)
1 (no frequency division)
D5 : ENIN ENIN register is used to start up IC and to give a trigger for initialization.
Output operation of the IC is performed only when ENIN is set to 1.
D7
GATE
0
MODE1
1
MODE2
Gate mode operation
*Default
Forward/reverse/braking
Forward/reverse/standby
No.A1760-12/20
LV8491CT
2
0
0
0
0
0
0
1
0
D7
D6
D5
D4
D3
D2
D1
D0
D2
D1
D0
D2
D1
D0
D2
D1
D0
D2
D1
D0
RST7 to RST0 : Specifies the number of clocks per period (0 to 255). Default = 0
3
0
0
0
0
0
0
1
1
D7
D6
D5
D4
D3
GTAS7 to GTAS0 : Sets the GATE_A pulse set value (0 to 255). Default = 0
4
0
0
0
0
0
1
0
0
D7
D6
D5
D4
D3
GTBR7 to GTBR0 : Sets the GATE_B pulse reset value (0 to 255). Default = 0
5
0
0
0
0
0
1
0
1
D7
D6
D5
D4
D3
GTBS7 to GTBS0 : Sets the GATE_B pulse set value (0 to 255). Default = 0
RST7-0
GTAS7-0
GATEA
GTBS7-0
GTBR7-0
GATEB
6
0
0
0
0
0
1
1
0
D7
D6
D5
D4
D3
STP7 to STP0 : Specifies the number of output pulse steps with regard to DRIVE input (1 to 256). Default = 1
The setting value range is handled as the data value plus 1.
When data is input in 8-bit units (0 to 255), it is handled as an STP period of 1 to 256.
No.A1760-13/20
LV8491CT
7
0
0
0
0
0
1
1
1
0
0
0
0
D3
D2
D1
D0
INITMOV7 to INITMOV4 : Sets the number of swing back of the initialization sequence to be performed (16 to 256). Default = 16
8
0
D3
D2
D1
D0
INIT7 to 4
16 to 256
0
0
0
0
0
16
0
0
0
1
1
32
0
0
1
0
2
48
0
0
1
1
3
64
0
1
0
0
4
80
0
1
0
1
5
96
0
1
1
0
6
112
0
1
1
1
7
128
1
0
0
0
8
144
1
0
0
1
9
160
1
0
1
0
10
176
1
0
1
1
11
192
1
1
0
0
12
208
1
1
0
1
13
224
1
1
1
0
14
240
1
1
1
1
15
256
0
0
0
1
0
0
0
0
0
D5
D4
D3
D2
D1
D0
NRPUL15 to NRPUL10: 0 to 63. Default = 0
Specifies the total number of output periods of the NR1 to NR5 drive waveforms during rise operation when
multiple drive waveforms are output continuously during actuator operation.
When set to 0, NR drive waveforms are not output during rise operation, and normal output operation is
performed.
9
0
0
0
0
1
0
0
1
0
0
D5
D4
D3
D2
D1
D0
D3
D2
D1
D0
NRP-A5 to NRP-A0: 0 to 63. Default = 0
This register specifies the first switching timing of the rise NR drive waveform.
It determines the number of NR1 waveform output periods during rise operation.
10
0
0
0
0
1
0
1
0
0
0
D5
D4
NRP-B5 to NRP-B0: 0 to 63. Default = 0
This register specifies the second switching timing of the rise NR drive waveform.
The NR2 waveform is output for a number of periods equal to the difference between NRP-A and NRP-B.
11
0
0
0
0
1
0
1
1
0
0
D5
D4
D3
D2
D1
D0
NRP-C5 to NRP-C0: 0 to 63. Default = 0
This register specifies the third switching timing of the rise NR drive waveform.
The NR3 waveform is output for a number of periods equal to the difference between NRP-B and NRP-C.
No.A1760-14/20
LV8491CT
12
0
0
0
0
1
1
0
0
0
0
D5
D4
D3
D2
D1
D0
NRP-D5 to NRP-D0: 0 to 63. Default = 0
This register specifies the fourth switching timing of the rise NR drive waveform.
The NR4 waveform is output for a number of periods equal to the difference between NRP-C and NRP-D,
and the NR5 waveform is output for a number of periods equal to the difference between NRP-D and
NRPUL1.
When setting the rise NR drive waveforms, the setting values should in principle satisfy the following relationship.
NRP-A ≤ NRP-B ≤ NRP-C ≤ NRP-D
(When this relationship is not satisfied, unintended drive waveforms may be output. However, this will not result in IC
breakdowns or other damage.)
13
0
0
0
0
1
1
0
1
0
0
D5
D4
D3
D2
D1
D0
NRPUL25 to NRPUL20: 0 to 63. Default = 0
Specifies the total number of output periods of the NR5 to NR1 drive waveforms during fall operation, when
multiple drive waveforms are output continuously during actuator operation.
When set to 0, NR drive waveforms are not output during fall operation, and operation stops.
14
0
0
0
0
1
1
1
0
0
0
D5
D4
D3
D2
D1
D0
D3
D2
D1
D0
NRP-E5 to NRP-E0: 0 to 63. Default = 0
This register specifies the first switching timing of the fall NR drive waveform.
It determines the number of NR5 waveform output periods during fall operation.
15
0
0
0
0
1
1
1
1
0
0
D5
D4
NRP-F5 to NRP-F0: 0 to 63. Default = 0
This register specifies the second switching timing of the fall NR drive waveform.
The NR4 waveform is output for a number of periods equal to the difference between NRP-E and NRP-F.
16
0
0
0
1
0
0
0
0
0
0
D5
D4
D3
D2
D1
D0
NRP-G5 to NRP-G0: 0 to 63. Default = 0
This register specifies the third switching timing of the fall NR drive waveform.
The NR3 waveform is output for a number of periods equal to the difference between NRP-F and NRP-G.
17
0
0
0
1
0
0
0
1
0
0
D5
D4
D3
D2
D1
D0
NRP-H5 to NRP-H0: 0 to 63. Default = 0
This register specifies the fourth switching timing of the fall NR drive waveform.
The NR2 waveform is output for a number of periods equal to the difference between NRP-G and NRP-H,
and the NR1 waveform is output for a number of periods equal to the difference between NRP-H and
NRPUL2.
When setting the fall NR drive waveforms, the setting values should in principle satisfy the following relationship.
NRP-E ≤ NRP-F ≤ NRP-G ≤ NRP-H
(When this relationship is not satisfied, unintended drive waveforms may be output. However, this will not result in IC
breakdowns or other damage.)
No.A1760-15/20
LV8491CT
18
0
0
0
1
0
0
1
0
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
D7
0
0
0
0
0
0
0
NR1GTBR7 to NR1GTBR0: 0 to 255. Default = 0
GATE_B pulse reset value for NR1 waveform
19
0
0
0
1
0
0
1
1
NR1GTBS7 to NR1GTBS0: 0 to 255. Default = 0
GATE_B pulse set value for NR1 waveform
20
0
0
0
1
0
1
0
0
NR2GTBR7 to NR2GTBR0: 0 to 255. Default = 0
GATE_B pulse reset value for NR2 waveform
21
0
0
0
1
0
1
0
1
NR2GTBS7 to NR2GTBS0: 0 to 255. Default = 0
GATE_B pulse set value for NR2 waveform
22
0
0
0
1
0
1
1
0
NR3GTBR7 to NR3GTBR0: 0 to 255. Default = 0
GATE_B pulse reset value for NR3 waveform
23
0
0
0
1
0
1
1
1
NR3GTBS7 to NR3GTBS0: 0 to 255. Default = 0
GATE_B pulse set value for NR3 waveform
24
0
0
0
1
1
0
0
0
NR4GTBR7 to NR4GTBR0: 0 to 255. Default = 0
GATE_B pulse reset value for NR4 waveform
25
0
0
0
1
1
0
0
1
NR4GTBS7 to NR4GTBS0: 0 to 255. Default = 0
GATE_B pulse set value for NR4 waveform
26
0
0
0
1
1
0
1
0
NR5GTBR7 to NR5GTBR0: 0 to 255. Default = 0
GATE_B pulse reset value for NR5 waveform
27
0
0
0
1
1
0
1
1
NR5GTBS7 to NR5GTBS0: 0 to 255. Default = 0
GATE_B pulse set value for NR5 waveform
28
No register address
READ only register line.
D7 : BUSY register Set to 1 when the IC is performing the output operation.
Set to 0 when the IC stops the output operation.
No.A1760-16/20
LV8491CT
Functional Description
1 period :
One period of OUT waveform operation is equivalent to one output operation.
Tf = 1 period
Initialization sequence (on or off and direction can be set by I2C) :
This is an internal sequence in which the actuator is moved to the initial position when the IC is started up.
Switching the value of ENIN register from 0 to 1 starts the IC.
The presence or absence of the initialization operation can be set using the initialization mode select register (INIT). If
the initialization operation is specified, the direction of the initialization sequence can be set using the M/I register.
• M/I register = 0 : Initialization processing in infinity direction
The IC performs the number of operations determined by STP setting period × INIT setting times in the infinite
direction, then waits for the period equivalent to STP setting period × 4 times, and performs the number of swing
back operations equal to STP setting period × RET setting times in the macro direction.
• M/I register = 1 : Auto macro operation in macro direction
The IC performs the number of operations determined by STP setting period × INIT setting times in the macro
direction, then waits for the period equivalent to STP setting periods × 4, and performs the number of swing back
operations equal to STP period setting period × RET setting times in the infinity direction.
CLK input :
The input pin for the external CLK input that provides the reference time for generating drive waveforms.
The frequency division ratio for I2C communication can be selected from 1/4, 1/2, and 1/1.
Drive waveforms are generated by counting this frequency-divided clk pulses as the basic count unit.
The LV8491CT supports frequency range of 10MHz to 60MHz depending on the frequency division ratio and counter
settings.
Register setting sequence example
(1) Apply VCC.
(2) Set up the register address 0x01 to 0x07 (setting up waveform and drive conditions)
(3) Set the ENIN register to 1 (initialization startup when the initialization sequence is enabled, or IC startup).
(4) AF operation starts (actuator operation instruction) according to the M/I and DRVPULSE settings.
I2C communication during output operation
I2C communication is possible to all registers during IC operation (during OUT output or when BUSY is high).
However, note that when drive waveform settings are changed during actuator or other operation, unintended
waveforms may be output.
No.A1760-17/20
LV8491CT
Actuator drive waveform settings :
Configuration of piezoelectric actuator drive waveform
f = 1 period
Ta
off
Tb
Drive parameter settings
Since the counter starts from zero,
a value minus 1 is set.
RST = Number of clock pulses in period minus 1
GTAS =
Ta + 1
Ta-1+2 = Ta+1
since the waveforms start after two clock pulses.
Rises here after two clock pulses from reference.
GTBR =
GTAS + off
Waveform start
reference point
GTBS =
GTBR + Tb
The drive waveforms are set using four parameters: RST, GTAS, GTBR and GTBS.
RST
: Parameter determines the period, and sets the reference clock pulse count minus 1.
GTAS : Parameter determines the time taken for the gate signal A to the falling edge from the reference point.
Since the signal raises after two clock pulses from the reference, the Ta reference clock cycle count plus 1 is
set.
GTBR : Parameter determines the time taken for the gate signal B to the rising edge from the reference point.
It sets the value obtained by adding the reference clock pulse count during the time from GTAS to “off.”
GTBS : Parameter determines the time taken for the gate signal B to the falling ewdge from the reference point.
It sets the value obtained by adding the reference clock pulse count during the time from GTBR to “Tb.”
[Example of settings] When setting reference clock to 10MHz, period to 13μs, Ta to 2.0μs, off to 0.3μs, and Tb to 3.0μs
Since the reference clock time is 0.1μs :
The period is 130 clks. → Specify 129 (RST value of 130 -1).
Ta is 20 clks. → Specify 21 (GTAS value of 20 + 1).
off is 3 clks. → Specify 24 (GTBR value of 21 + 3).
Tb is 30 clks. → Specify 54 (GTBS value of 24 + 30).
No.A1760-18/20
LV8491CT
Timing charts
Enlarged view of the sequence of output signals
(RST setting + 1) ×
number of clock pulses
Operation toward infinity
(GTAS setting - 1) ×
number of clock pulses
(GTAS setting - 1) ×
number of clock pulses
OUT1
(GTAS setting - 1) × number of clock pulses
OUT2
(GTBR setting -1) × number of clock pulses
Operation toward macro
(RST setting + 1) ×
number of clock pulses
(GTBR setting -1) × number of clock pulses
OUT1
(GTBS setting - 1) × number of clock pulses
OUT2
(GTAS setting - 1) ×
number of clock pulses
(GTAS setting - 1) ×
number of clock pulses
Sequence of initial setting operation (“on” or “off” can be set by the serial settings.)
When M/I register = 00 → Movement toward infinity position
Startup or initialization sequence start when ENIN is set to 1
ENIN register
1 period
OUT1
OUT2
Operation toward infinity
Standby state
STP period × INIT times
STP period × 4 STP period × RET setting times
Operation toward macro
Initial setting operation time
BUSY register
High during initial setting in wait state too
BUSY output is high during initial setting operation.
BUSY output is low after initial setting.
When M/I register = 01 → Movement toward macro position
Startup or initialization sequence start when ENIN is set to 1
ENIN register
OUT1
1 period
OUT2
Operation toward macro
STP period × INIT times
Standby state
Operation toward infinity
STP period × 4 STP period × RET setting times
Initial setting operation time
BUSY register
High during initial setting in wait state too
BUSY output is high during initial setting operation.
BUSY output is low after initial setting.
No.A1760-19/20
LV8491CT
Sequence of operations triggered by DRVPULSE input
EN
M/I register state
Infinity direction logic selection
Operation stops when ENIN is set to 0.
Macro direction logic selection
Serial communication of operation instruction completed.
00000000_00000010 (operation 2 times toward infinity)
DRVPULSE setting
OUT1
I2C communication operation instruction completed
00000000_10000010 (operation 2 times toward macro)
Equivalent to 2 pulses = STP setting period × operation for 2 times
1 period
Operation toward infinity (STP setting period × 2 times)
Operation toward macro
OUT2
I2C communication
Operation starts on completion of DRVPULSE input.
Returns to high
when ENIN is set to 0,
even in the middle of operation.
BUSY
BUSY register is set to 1 only during operation
Gate setting output logic
1 period
GATE MODE1 : Forward, Braking, Reverse
Forward
Forward
Output mode
OUT1
Braking Braking
OUT2
on
OUT1
1 period
Forward
Forward
OUT1
Wait
Wait
OUT2
off
on
OUT2 OUT1
off
Reverse
GATE MODE2 : Forward, Wait, Reverse
off
OUT2
on
on
off
Forward
Reverse
off
off
off
OUT1
off
OUT2 OUT1
on
on
OUT2
off
Braking
off
Wait
Reverse
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of July, 2010. Specifications and information herein are subject
to change without notice.
PS No.A1760-20/20