TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 25-W STEREO CLASS-D AUDIO POWER AMPLIFIER FEATURES APPLICATIONS • • • • • • • • • • • • 25-W/ch into a 4-Ω Load from a 27-V Supply 20-W/ch into a 4-Ω Load from a 24-V Supply Operates from 10 V to 30 V Efficient Class-D Operation Eliminates Need for Heat Sinks Four Selectable, Fixed-Gain Settings Internal Oscillator (No External Components Required) Single-Ended Analog Inputs Thermal and Short-Circuit Protection With Auto Recovery Space-Saving Surface-Mount 24-Pin TSSOP Package TPA3120D2 Pin-to-Pin compatible with TPA3120D2 Advanced Power-Off Pop Reduction Televisions DESCRIPTION The TPA3123D2 is a 25-W (per channel) efficient, Class-D audio power amplifier for driving stereo speakers in a single-ended configuration or a mono bridge-tied speaker. The TPA3123D2 can drive stereo speakers as low as 4 Ω. The efficiency of the TPA3123D2 eliminates the need for an external heat sink when playing music. The gain of the amplifier is controlled by two gain select pins. The gain selections are 20, 26, 32, 36 dB. The patented start-up and shut-down sequences minimize pop noise in the speakers without additional circuitry. SIMPLIFIED APPLICATION CIRCUIT TPA3123D2 1 mF 0.22 mF Left Channel LIN BSR Right Channel RIN ROUT 1 mF PGNDR PGNDL 1 mF BYPASS AGND 22 mH 470 mF 0.68 mF 0.68 mF LOUT 22 mH BSL 470 mF 0.22 mF 10 V to 30 V AVCC 10 V to 30 V PVCCL PVCCR VCLAMP Shutdown Control Mute Control SD 1 mF MUTE GAIN0 GAIN1 } 4-Step Gain Control Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. System Two, Audio Precision are trademarks of Audio Precision, Inc. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2007, Texas Instruments Incorporated TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. PWP (TSSOP) PACKAGE (TOP VIEW) PVCCL SD PVCCL MUTE LIN RIN BYPASS AGND AGND PVCCR VCLAMP PVCCR 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 PGNDL PGNDL LOUT BSL AVCC AVCC GAIN0 GAIN1 BSR ROUT PGNDR PGNDR Table 1. TERMINAL FUNCTIONS TERMINAL 24-PIN (PWP) I/O/P DESCRIPTION SD 2 I Shutdown signal for IC (low = disabled, high = operational). TTL logic levels with compliance to AVCC RIN 6 I Audio input for right channel LIN 5 I Audio input for left channel GAIN0 18 I Gain select least-significant bit. TTL logic levels with compliance to AVCC GAIN1 17 I Gain select most-significant bit. TTL logic levels with compliance to AVCC MUTE 4 I Mute signal for quick disable/enable of outputs (high = outputs switch at 50% duty cycle, low = outputs enabled). TTL logic levels with compliance to AVCC BSL 21 I/O PVCCL 1, 3 P Power supply for left-channel H-bridge, not internally connected to PVCCR or AVCC LOUT 22 O Class-D 1/2-H-bridge positive output for left channel 23, 24 P Power ground for left-channel H-bridge Internally generated voltage supply for bootstrap capacitors NAME PGNDL VCLAMP 11 P BSR 16 I/O Bootstrap I/O for right channel ROUT 15 O Class-D 1/2-H-bridge negative output for right channel PGNDR 13, 14 P Power ground for right-channel H-bridge. PVCCR 10, 12 P Power supply for right-channel H-bridge, not connected to PVCCL or AVCC AGND 9 P Analog ground for digital/analog cells in core AGND 8 P Analog ground for analog cells in core BYPASS 7 O Reference for preamplifier inputs. Nominally equal to AVCC/8. Also controls start-up time via external capacitor sizing. 19, 20 P High-voltage analog power supply. Not internally connected to PVCCR or PVCCL Die pad P Connect to ground. Thermal pad should be soldered down on all applications to properly secure device to printed wiring board. AVCC Thermal pad 2 Bootstrap I/O for left channel Submit Documentation Feedback TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) VCC Supply voltage AVCC, PVCC VI Logic input voltage SD, MUTE, GAIN0, GAIN1 VIN Analog input voltage RIN, LIN Continuous total power dissipation VALUE UNIT –0.3 to 36 V –0.3 to VCC + 0.3 V –0.3 to 7 V See Dissipation Ratings table TA Operating free-air temperature range –40 to 85 °C TJ Operating junction temperature range –40 to 150 °C Tstg Storage temperature range –65 to 150 °C RL Load resistance (minimum value) 3.2 Ω ESD Electrostatic Discharge ±2 kV ± 500 V (1) Human-body model (all pins) Charged-device model (all pins) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operations of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. DISSIPATION RATINGS (1) (2) PACKAGE (1) (2) TA ≤ 25°C DERATING FACTOR TA = 70°C TA = 85°C 24-pin TSSOP 4.16 W 33.3 mW/°C 2.67 W 2.16 W For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. The thermal pad must be soldered to a thermal land on the printed-circuit board. See the PowerPAD Thermally Enhanced Package application note (SLMA002). RECOMMENDED OPERATING CONDITIONS MIN MAX 10 30 VCC Supply voltage PVCC, AVCC VIH High-level input voltage SD, MUTE, GAIN0, GAIN1 VIL Low-level input voltage SD, MUTE, GAIN0, GAIN1 0.8 SD, VI = VCC, VCC = 30 V 125 MUTE, VI = VCC, VCC = 30 V 125 GAIN0, GAIN1, VI = VCC, VCC = 24 V 125 IIH High-level input current IIL Low-level input current TA Operating free-air temperature 2 1 MUTE, VI = 0 V, VCC = 30 V 1 V μA μA 1 –40 Submit Documentation Feedback V V SD, VI = 0, VCC = 30 V GAIN0, GAIN1, VI = 0 V, VCC = 24 V UNIT 85 °C 3 TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 DC CHARACTERISTICS TA = 25°C, VCC = 24 V, RL = 4 Ω (unless otherwise noted) PARAMETER TEST CONDITIONS | VOS | Class-D output offset voltage (measured differentially in BTL mode as shown in Figure 30) VI = 0 V, AV = 36 dB V(BYPASS) Bypass output voltage No load ICC(q) Quiescent supply current SD = 2 V, MUTE = 0 V, No load ICC(q) Quiescent supply current in mute mode MUTE = 0.8 V, No load ICC(q) Quiescent supply current in shutdown mode SD = 0.8 V , No load rDS(on) Drain-source on-state resistance TYP MAX 7.5 50 AVCC/ 8 23 37 23 0.39 Gain GAIN = 2 V Mute Attenuation mV mA mA 1 mA mΩ GAIN0 = 0.8 V 18 20 22 GAIN0 = 2 V 24 26 28 GAIN0 = 0.8 V 30 32 34 GAIN0 = 2 V 34 36 38 VI = 1 Vrms UNIT V 200 GAIN1 = 0.8 V G MIN –82 dB dB AC CHARACTERISTICS TA = 25°C, VCC = 24 V, RL = 4Ω (unless otherwise noted) PARAMETER ksvr Supply ripple rejection Output power at 1% THD+N PO Output power at 10% THD+N TEST CONDITIONS VCC = 24, Vripple = 200 mVPP Gain = 20 dB MIN –48 1 kHz –52 VCC = 24 V, RL = 4 Ω, f = 1 kHz 16 VCC = 24 V, RL = 8 Ω, f = 1 kHz 8 VCC= 24 V, RL = 4 Ω, f = 1 kHz 20 VCC = 24 V, RL = 8 Ω, f = 1 kHz 10 RL = 4 Ω, f = 1 kHz, PO = 10 W 0.08% RL = 8 Ω, f = 1 kHz, PO = 5 W 0.08% THD+N Total harmonic distortion + noise Vn Output integrated noise floor 20 Hz to 22 kHz, A-weighted filter, Gain = 20 dB Crosstalk PO = 1 W, f = 1 kHz; Gain = 20 dB Signal-to-noise ratio Max output at THD+N < 1%, f = 1 kHz, Gain = 20 dB SNR Thermal trip point Thermal hysteresis fOSC Oscillator frequency 230 MAX UNIT dB W 85 μV –80 dBV –60 dB 99 dB 150 °C 30 °C 250 270 kHz mute delay time from mute input switches high until outputs muted 120 msec unmute delay time from mute input switches low until outputs unmuted 120 msec Δt 4 TYP 100 Hz Submit Documentation Feedback TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 FUNCTIONAL BLOCK DIAGRAM BSL AVCC PVCCL AVDD REGULATOR HS LOUT + - VCLAMP LS AVDD AVDD PGNDL LIN SC DETECT AVDD/2 AGND CONTROL SD BIAS VCLAMP THERMAL MUTE MUTE CONTROL OSC/RAMP BYPASS GAIN1 BYPASS AV CONTROL GAIN0 SC DETECT BSR PVCCR HS ROUT - VCLAMP + LS PGNDR AVDD AVDD RIN AVDD/2 Submit Documentation Feedback 5 TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 TYPICAL CHARACTERISTICS All tests are made at frequency = 1 kHz unless otherwise noted. TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY 10 THD+N - Total Harmonic Distortion + Noise - % THD+N - Total Harmonic Distortion + Noise - % 10 VCC = 18 V RL = 4 W (SE) Gain = 20 dB 1 PO = 5 W PO = 1 W 0.1 PO = 2.5 W 0.01 20 1k 100 1 PO = 10 W PO = 1 W 0.1 PO = 5 W 100 1k 10k 20k f − Frequency − Hz f − Frequency − Hz Figure 1. Figure 2. TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER THD+N - Total Harmonic Distortion + Noise - % THD+N - Total Harmonic Distortion + Noise - % 6 RL = 4 W (SE) Gain = 20 dB 0.01 20 10k 20k 10 VCC = 24 V RL = 8 W (SE) Gain = 20 dB 1 PO = 2.5 W PO = 5 W 0.1 PO = 1 W 0.01 20 VCC = 24 V 100 1k 10k 20k 10 RL = 4 W (SE) Gain = 20 dB VCC = 24 V 1 VCC = 18 V VCC = 12 V 0.1 0.01 10 m 100 m 1 f − Frequency − Hz PO − Output Power − W Figure 3. Figure 4. Submit Documentation Feedback 10 40 TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 TYPICAL CHARACTERISTICS (continued) All tests are made at frequency = 1 kHz unless otherwise noted. 10 CROSSTALK vs FREQUENCY 0 RL = 8 W (SE) Gain = 20 dB VCC = 24 V 1 -10 VCC = 18 V VO = 1 Vrms -20 RL = 4 W (SE) Gain = 20 dB -30 VCC = 18 V Crosstalk - dB VCC = 12 V -40 -50 L to R -60 0.1 -70 -80 R to L -90 0.01 10 m 100 m 1 PO − Output Power − W 10 -100 20 40 100 10k 20k 1k f − Frequency − Hz Figure 5. Figure 6. CROSSTALK vs FREQUENCY GAIN/PHASE vs FREQUENCY 0 200 VCC = 18 V, VO = 1 V, -10 Gain 20 R L = 8 W, Gain = 20 dB -20 100 15 Gain - dB Crosstalk - dB -30 -40 -50 L to R 0 Phase 10 -60 -70 5 R to L -80 0 20 100 1k -100 RL = 4 W (SE) Gain = 20 dB Lfilt = 33 mH -200 Cfilt = 1 mF -90 -100 VCC = 24 V 10k 20k Phase - o THD+N - Total Harmonic Distortion + Noise - % TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER Cdc = 470 mF 20 100 200 1k 2k 10k 20k f − Frequency − Hz -300 100k f − Frequency − Hz Figure 7. Figure 8. Submit Documentation Feedback 7 TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 TYPICAL CHARACTERISTICS (continued) All tests are made at frequency = 1 kHz unless otherwise noted. GAIN/PHASE vs FREQUENCY OUTPUT POWER vs SUPPLY VOLTAGE 200 22.5 32 30 150 28 Gain 20 0 15 Phase -50 12.5 VCC = 24 V RL = 8 W (SE) Gain = 20 dB Lfilt = 47 mH 10 7.5 -100 -150 PO - Output Power - W 50 Phase - o Gain - dB 26 100 17.5 24 22 18 16 14 12 THD = 1% 10 8 -200 Cdc = 470 mF 6 5 100 200 THD = 10% 20 Cfilt = 0.22 mF 20 RL = 4 W (SE) Gain = 20 dB 1k 2k 4 -250 100k 10k 20k 2 10 12 14 f − Frequency − Hz 16 A. 26 28 30 100 RL = 8 W (SE) Gain = 20 dB 90 80 13 12 11 10 THD = 10% 70 Efficiency - % PO - Output Power - W 8 24 EFFICIENCY vs OUTPUT POWER 14 9 8 7 6 5 4 3 2 1 10 22 Dashed line represents thermally limited region. Figure 10. OUTPUT POWER vs SUPPLY VOLTAGE 15 20 VSS − Supply Voltage − V Figure 9. 17 16 18 THD = 1% 24 V 18 V 60 12 V 50 40 30 20 RL = 4 W (SE) Gain = 20 dB 10 0 12 14 16 18 20 22 24 26 28 30 0 2 4 6 8 10 12 14 VSS - Supply Voltage - V PO − Output Power − W Figure 11. Figure 12. Submit Documentation Feedback 16 18 20 TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 TYPICAL CHARACTERISTICS (continued) All tests are made at frequency = 1 kHz unless otherwise noted. EFFICIENCY vs OUTPUT POWER 2 90 1.8 80 1.6 24 V 18 V 12 V ICC − Supply Current − A 100 70 Efficiency - % SUPPLY CURRENT vs OUTPUT POWER 60 50 40 30 RL = 4 W (SE) Gain = 20 dB 1.4 1.2 1 24 V 0.8 0.6 18 V 0.4 20 12 V RL = 8 W (SE) Gain = 20 dB 10 0.2 0 0 0 1 2 3 4 5 6 7 8 9 10 11 12 0 4 8 PO − Output Power − W 16 20 24 28 32 Figure 13. Figure 14. SUPPLY CURRENT vs OUTPUT POWER POWER SUPPLY REJECTION RATIO vs FREQUENCY 0.9 36 40 0 -10 24 V Power Supply Rejection Ratio - dB RL = 8 W, Gain = 20 dB 0.8 ICC - Supply Current - A 12 PO − Output Power − W 0.7 18 V 0.6 0.5 12 V 0.4 0.3 0.2 0.1 -20 -30 VCC = 24 V VO(ripple) = 0.2 VPP RL = 4 W (SE) Gain = 20 dB -40 -50 -60 -70 -80 -90 -100 -110 0 0 2.5 5 7.5 10 12.5 15 17.5 20 22.5 PO - Output Power - W 25 -120 20 Figure 15. 100 1k 10k 20k f − Frequency − Hz Figure 16. Submit Documentation Feedback 9 TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 TYPICAL CHARACTERISTICS (continued) All tests are made at frequency = 1 kHz unless otherwise noted. TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER THD+N - Total Harmonic Distortion + Noise - % THD+N - Total Harmonic Distortion + Noise - % 10 VCC = 24 V RL = 8 W (BTL) Gain = 20 dB PO = 20 W 1 0.1 PO = 5 W PO = 1 W 0.01 0.001 20 100 1k 1 VCC = 18 V VCC = 12 V 0.1 10 Figure 17. Figure 18. GAIN/PHASE vs FREQUENCY OUTPUT POWER vs SUPPLY VOLTAGE 400 60 300 50 Gain 40 100 VCC = 24 V, 0 RL = 8 W (BTL), Gain = 20 dB, Lfilt = 33 mH, PO - Output Power - W 200 Phase - ° Phase 45 THD = 10% 40 35 30 THD = 1% 25 20 15 -100 10 5 -30 100 RL = 8 W (BTL) Gain = 20 dB 55 Cfilt = 1 mF 1k 10k f - Frequency - Hz Figure 19. 10 1 PO − Output Power − W 0 20 100 m 65 10 Gain - dB VCC = 24 V f − Frequency − Hz 20 -20 RL = 8 W (BTL) Gain = 20 dB 0.01 10 m 10k 20k 30 -10 10 -200 200k 0 10 12 14 16 18 20 22 24 26 VSS − Supply Voltage − V A. Dashed line represents thermally limited region. Figure 20. Submit Documentation Feedback 28 30 TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 TYPICAL CHARACTERISTICS (continued) All tests are made at frequency = 1 kHz unless otherwise noted. EFFICIENCY vs OUTPUT POWER POWER SUPPLY REJECTION RATIO vs FREQUENCY 100 0 Power Supply Rejection Ratio - dB 90 80 Efficiency - % 70 12 V 60 24 V 18 V 50 40 30 20 RL = 8 W (BTL) Gain = 20 dB 10 0 0 4 8 12 16 20 24 28 32 36 40 -20 VCC = 24 V VO(ripple) = 200 mV RL = 8 W (BTL) Gain = 20 dB -40 -60 -80 -100 -120 -140 20 PO − Output Power − W 100 1k 10k 20k f − Frequency − Hz Figure 21. Figure 22. Submit Documentation Feedback 11 TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 APPLICATION INFORMATION CLASS-D OPERATION This section focuses on the class-D operation of the TPA3123D2. Traditional Class-D Modulation Scheme The TPA3123D2 operates in AD mode. There are two main configurations that may be used. For stereo operation, the TPA3123D2 should be configured in a single-ended (SE) half-bridge amplifier. For mono applications, TPA3123D2 may be used as a bridge-tied-load (BTL) amplifier. The traditional class-D modulation scheme, which is used in the TPA3123D2 BTL configuration, has a differential output where each output is 180 degrees out of phase and changes from ground to the supply voltage, VCC. Therefore, the differential prefiltered output varies between positive and negative VCC, where filtered 50% duty cycle yields 0 V across the load. The class-D modulation scheme with voltage and current waveforms is shown in Figure 23 and Figure 24. +VCC 0V Output Current Figure 23. Class-D Modulation for TPA3123D2 SE Configuration +VCC 0V +VCC 0V +VCC Differential Voltage Across Speaker 0V –VCC Output Current Figure 24. Class-D Modulation for TPA3123D2 BTL Configuration Supply Pumping One issue encountered in single ended (SE) class-D amplifier designs is supply pumping. Power-supply pumping is a rise in the local supply voltage due to energy being driven back to the supply by operation of the class-D amplifier. This phenomenon is most evident at low audio frequencies and when both channels are operating at the same frequency and phase. At low levels, power supply pumping results in distortion in the audio output due to fluctuations in supply voltage. At higher levels, pumping can cause the overvoltage protection to operate, which temporarily shuts down the audio output. 12 Submit Documentation Feedback TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 APPLICATION INFORMATION (continued) Several things can be done to relieve power-supply pumping. The lowest impact is to operate the two inputs out of phase 180° and reverse the speaker connections. Because most audio is highly correlated, this causes the supply pumping to be out of phase and not as severe. If this is not enough, the amount of bulk capacitance on the supply must be increased. Also, improvement is realized by hooking other supplies to this node which sinks some of the excess current. Power supply pumping should be tested by operating the amplifier at low frequencies and high output levels. Gain Setting via GAIN0 and GAIN1 Inputs The gain of the TPA3123D2 is set by two input terminals, GAIN0 and GAIN1. The gains listed in Table 2 are realized by changing the taps on the input resistors and feedback resistors inside the amplifier. This causes the input impedance (ZI) to be dependent on the gain setting. The actual gain settings are controlled by ratios of resistors, so the gain variation from part-to-part is small. However, the input impedance from part-to-part at the same gain may shift by ±20% due to shifts in the actual resistance of the input resistors. For design purposes, the input network (discussed in the next section) should be designed assuming an input impedance of 8 kΩ, which is the absolute minimum input impedance of the TPA3123D2. At the higher gain settings, the input impedance could increase as high as 72 kΩ. Table 2. Gain Setting GAIN1 GAIN0 AMPLIFIER GAIN (dB), TYPICAL INPUT IMPEDANCE (kΩ), TYPICAL 0 0 20 10 0 1 26 15 1 0 32 30 1 1 36 60 INPUT RESISTANCE Changing the gain setting can vary the input resistance of the amplifier from its smallest value, 10 kΩ ±20%, to the largest value, 60 kΩ ±20%. As a result, if a single capacitor is used in the input high-pass filter, the –3-dB or cutoff frequency may change when changing gain steps. Zf Ci Input Signal IN Zi The –3-dB frequency can be calculated using Equation 1. Use the ZI values given in Table 2. f = 1 2p Zi Ci (1) Submit Documentation Feedback 13 TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 INPUT CAPACITOR, CI In the typical application, an input capacitor (CI) is required to allow the amplifier to bias the input signal to the proper dc level for optimum operation. In this case, CI and the input impedance of the amplifier (ZI) form a high-pass filter with the corner frequency determined in Equation 2. –3 dB fc = 1 2p Zi Ci fc (2) The value of CI is important, as it directly affects the bass (low-frequency) performance of the circuit. Consider the example where ZI is 20 kΩ and the specification calls for a flat bass response down to 20 Hz. Equation 2 is reconfigured as Equation 3. Ci = 1 2p Zi fc (3) In this example, CI is 0.4 µF; so, one would likely choose a value of 0.47 μF as this value is commonly used. If the gain is known and is constant, use ZI from Table 2 to calculate CI. A further consideration for this capacitor is the leakage path from the input source through the input network (CI) and the feedback network to the load. This leakage current creates a dc offset voltage at the input to the amplifier that reduces useful headroom, especially in high-gain applications. For this reason, a low-leakage tantalum or ceramic capacitor is the best choice. When polarized capacitors are used, the positive side of the capacitor should face the amplifier input in most applications as the dc level there is held at VBYP (VCC/8), which is likely higher than the source dc level. Note that it is important to confirm the capacitor polarity in the application. Additionally, lead-free solder can create dc offset voltages, and it is important to ensure that boards are cleaned properly. Single-Ended Output Capacitor, CO In single ended (SE) applications, the dc blocking capacitor forms a high-pass filter with the speaker impedance. The frequency response rolls of with decreasing frequency at a rate of 20 dB/decade. The cutoff frequency is determined by: fc = 1/2πCOZL Table 3 shows some common component values and the associated cutoff frequencies: Table 3. Common Filter Responses Speaker Impedance (Ω) 14 CSE – DC Blocking Capacitor (μF) fc = 60 Hz (–3 dB) fc = 40 Hz (–3 dB) fc = 20 Hz (–3 dB) 4 680 1000 2200 8 330 470 1000 Submit Documentation Feedback TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 Output Filter and Frequency Response For the best frequency response, a flat-passband output filter (second-order Butterworth) may be used. The output filter components consist of the series inductor and capacitor to ground at the LOUT and ROUT pins. There are several possible configurations depending on the speaker impedance, and whether the output configuration is single ended (SE) or bridge-tied load (BTL). Table 4 lists the recommended values for the filter components. It is important to use a high-quality capacitor in this application. A rating of at least X7R is required. Table 4. Recommended Filter Output Components Output Configuration Speaker Impedance (Ω) Filter Inductor (μH) Filter Capacitor (nF) 4 22 680 8 47 390 4 10 1500 8 22 680 Single Ended (SE) Bridge Tied Load (BTL) LOUT Lfilter LOUT / ROUT Cfilter Cfilter ROUT Lfilter Lfilter Cfilter Figure 25. BTL Filter Configuration Figure 26. SE Filter Configuration Power-Supply Decoupling, CS The TPA3123D2 is a high-performance CMOS audio amplifier that requires adequate power-supply decoupling to ensure that the output total harmonic distortion (THD) is as low as possible. Power-supply decoupling also prevents oscillations for long lead lengths between the amplifier and the speaker. The optimum decoupling is achieved by using two capacitors of different types that target different types of noise on the power-supply leads. For higher-frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor, typically 0.1 μF to 1 µF, placed as close as possible to the device VCC lead works best. For filtering lower frequency noise signals, a larger aluminum electrolytic capacitor of 470 μF or greater placed near the audio power amplifier is recommended. The 470-μF capacitor also serves as local storage capacitor for supplying current during large signal transients on the amplifier outputs. The PVCC terminals provide the power to the output transistors, so a 470-µF or larger capacitor should be placed on each PVCC terminal. A 10-µF capacitor on the AVCC terminal is adequate. These capacitors must be properly derated for voltage and ripple current rating to ensure reliability. BSN and BSP Capacitors The half H-bridge output stages use only NMOS transistors. Therefore, they require bootstrap capacitors for the high side of each output to turn on correctly. A 220-nF ceramic capacitor, rated for at least 25 V, must be connected from each output to its corresponding bootstrap input. Specifically, one 220-nF capacitor must be connected from LOUT to BSL, and one 220-nF capacitor must be connected from ROUT to BSR. The bootstrap capacitors connected between the BSx pins and their corresponding outputs function as a floating power supply for the high-side N-channel power MOSFET gate-drive circuitry. During each high-side switching cycle, the bootstrap capacitors hold the gate-to-source voltage high enough to keep the high-side MOSFETs turned on. Submit Documentation Feedback 15 TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 VCLAMP Capacitor To ensure that the maximum gate-to-source voltage for the NMOS output transistors is not exceeded, one internal regulator clamps the gate voltage. One 1-μF capacitor must be connected from VCLAMP (pin 11) to ground and must be rated for at least 16 V. The voltages at the VCLAMP terminal may vary with VCC and may not be used for powering any other circuitry. VBYP Capacitor Selection The scaled supply reference (VBYP) nominally provides an AVCC/8 internal bias for the preamplifier stages. The external capacitor for this reference (CBYP) is a critical component and serves several important functions. During start-up or recovery from shutdown mode, CBYP determines the rate at which the amplifier starts. The start up time is proportional to 0.5 s per microfarad. Thus, the recommended 1-μF capacitor results in a start-up time of approximately 500 ms. The second function is to reduce noise produced by the power supply caused by coupling with the output drive signal. This noise could result in degraded power supply-rejection and THD+N. The circuit is designed for a CBYP value of 1 μF for best pop performance. The inputs capacitors should have the same value. A ceramic or tantalum low-ESR capacitor is recommended. SHUTDOWN OPERATION The TPA3123D2 employs a shutdown mode of operation designed to reduce supply current (ICC) to the absolute minimum level during periods of nonuse for power conservation. The SHUTDOWN input terminal should be held high (see specification table for trip point) during normal operation when the amplifier is in use. Pulling SHUTDOWN low causes the outputs to mute and the amplifier to enter a low-current state. Never leave SHUTDOWN unconnected, because amplifier operation would be unpredictable. For the best power-up pop performance, place the amplifier in the shutdown or mute mode prior to applying the power-supply voltage. MUTE Operation The MUTE pin is an input for controlling the output state of the TPA3123D2. A logic high on this terminal causes the outputs to run at a constant 50% duty cycle. A logic low on this pin enables the outputs. This terminal may be used as a quick disable/enable of outputs when changing channels on a television or transitioning between different audio sources. The MUTE terminal should never be left floating. For power conservation, the SHUTDOWN terminal should be used to reduce the quiescent current to the absolute minimum level. USING LOW-ESR CAPACITORS Low-ESR capacitors are recommended throughout this application section. A real (as opposed to ideal) capacitor can be modeled simply as a resistor in series with an ideal capacitor. The voltage drop across this resistor minimizes the beneficial effects of the capacitor in the circuit. The lower the equivalent value of this resistance, the more the real capacitor behaves like an ideal capacitor. SHORT-CIRCUIT PROTECTION The TPA3123D2 has short-circuit protection circuitry on the outputs that prevents damage to the device during output-to-output shorts and output-to-GND shorts after the filter and output capacitor (at the speaker terminal.) Directly at the device terminals, the protection circuitry prevents damage to device during output-to-output, output-to-ground, and output-to-supply. When a short circuit is detected on the outputs, the part immediately disables the output drive. This is an unlatched fault. Normal operation is restored when the fault is removed. 16 Submit Documentation Feedback TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 THERMAL PROTECTION Thermal protection on the TPA3123D2 prevents damage to the device when the internal die temperature exceeds 150°C. There is a ±15°C tolerance on this trip point from device to device. Once the die temperature exceeds the thermal set point, the device enters into the shutdown state and the outputs are disabled. This is not a latched fault. The thermal fault is cleared once the temperature of the die is reduced by 30°C. The device begins normal operation at this point with no external system interaction. PRINTED-CIRCUIT BOARD (PCB) LAYOUT Because the TPA3123D2 is a class-D amplifier that switches at a high frequency, the layout of the printed-circuit board (PCB) should be optimized according to the following guidelines for the best possible performance. • Decoupling capacitors—The high-frequency 0.1-µF decoupling capacitors should be placed as close to the PVCC (pins 1, 3, 10, and 12) and AVCC (pins 19 and 20) terminals as possible. The VBYP (pin 7) capacitor and VCLAMP (pin 11) capacitor should also be placed as close to the device as possible. Large (220-µF or greater) bulk power-supply decoupling capacitors should be placed near the TPA3123D2 on the PVCCL and PVCCR terminals. • Grounding—The AVCC (pins 19 and 20) decoupling capacitor and VBYP (pin 7) capacitor should each be grounded to analog ground (AGND, pins 8 and 9). The PVCCx decoupling capacitors and VCLAMP capacitors should each be grounded to power ground (PGND, pins 13, 14, 23, and 24). Analog ground and power ground should be connected at the thermal pad, which should be used as a central ground connection or star ground for the TPA3123D2. • Output filter—The reconstruction filter (L1, L2, C9, and C16) should be placed as close to the output terminals as possible for the best EMI performance. The capacitors should be grounded to power ground. • Thermal pad—The thermal pad must be soldered to the PCB for proper thermal performance and optimal reliability. The dimensions of the thermal pad and thermal land are described in the mechanical section at the back of the data sheet. See TI Technical Briefs SLMA002 and SLOA120 for more information about using the thermal pad. For recommended PCB footprints, see figures at the end of this data sheet. For an example layout, see the TPA3123D2 Evaluation Module (TPA3123D2EVM) User Manual, (SLOU189). Both the EVM user manual and the thermal pad application note are available on the TI Web site at http://www.ti.com. Submit Documentation Feedback 17 TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 VCC 470 mF 22 mH 470 mF +LOUT 1.0 mF 470 mF 1 2 3 4 5 6 7 8 9 10 11 12 Right In 1.0 mF 1.0 mF PVCCL PGNDL SD PGNDL PVCCL LOUT MUTE BSL LIN TPA3123D2 AVCC RIN AVCC BYPASS GAIN0 AGND GAIN1 AGND BSR PVCCR ROUT VCLAMP PGNDR PVCCR PGNDR THERMAL 1.0 mF Left In 24 23 22 21 20 19 18 17 16 15 14 13 0.68 mF 0.22 mF -LOUT VCC -ROUT 0.22 mF 0.68 mF 25 Shutdown Control 22 mH +ROUT Mute Control 470 mF 1.0 mF 1.0 mF 0.1 mF 10 mF Figure 27. Schematic for Single Ended (SE) Configuration VCC 22 mH 470 mF 1.0 mF 1 2 3 4 5 6 7 8 9 10 11 12 + In - In 1.0 mF +OUT 1.0 mF 1.0 mF PVCCL PGNDL SD PGNDL PVCCL LOUT MUTE BSL LIN TPA3123D2 AVCC RIN AVCC BYPASS GAIN0 AGND GAIN1 AGND BSR PVCCR ROUT VCLAMP PGNDR PVCCR PGNDR THERMAL 470 mF 24 23 22 21 20 19 18 17 16 15 14 13 0.68 mF 0.22 mF VCC 0.22 mF 0.68 mF 25 Shutdown Control 22 mH -OUT Mute Control 1.0 mF 1.0 mF 0.1 mF 10 mF Figure 28. Schematic for Bridge Tied (BTL) Configuration 18 Submit Documentation Feedback TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 BASIC MEASUREMENT SYSTEM This application note focuses on methods that use the basic equipment listed below: • Audio analyzer or spectrum analyzer • Digital multimeter (DMM) • Oscilloscope • Twisted-pair wires • Signal generator • Power resistor(s) • Linear regulated power supply • Filter components • EVM or other complete audio circuit Figure 29 shows the block diagrams of basic measurement systems for class-AB and class-D amplifiers. A sine wave is normally used as the input signal because it consists of the fundamental frequency only (no other harmonics are present). An analyzer is then connected to the audio power amplifier (APA) output to measure the voltage output. The analyzer must be capable of measuring the entire audio bandwidth. A regulated dc power supply is used to reduce the noise and distortion injected into the APA through the power pins. A System Two™ audio measurement system (AP-II) by Audio Precision™ includes the signal generator and analyzer in one package. The generator output and amplifier input must be ac-coupled. However, the EVMs already have the ac-coupling capacitors, (CIN), so no additional coupling is required. The generator output impedance should be low to avoid attenuating the test signal, and is important because the input resistance of APAs is not high. Conversely, the analyzer input impedance should be high. The output resistance, ROUT, of the APA is normally in the hundreds of milliohms and can be ignored for all but the power-related calculations. Figure 29(a) shows a class-AB amplifier system. It takes an analog signal input and produces an analog signal output. This amplifier circuit can be directly connected to the AP-II or other analyzer input. This is not true of the class-D amplifier system shown in Figure 29(b), which requires low-pass filters in most cases in order to measure the audio output waveforms. This is because it takes an analog input signal and converts it into a pulse-width modulated (PWM) output signal that is not accurately processed by some analyzers. Submit Documentation Feedback 19 TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 Power Supply Signal Generator APA RL Analyzer 20 Hz - 20 kHz (a) Basic Class-AB Power Supply Lfilt Signal Generator Class-D APA Cfilt RL (b) Traditional Class-D Figure 29. Audio Measurement Systems 20 Submit Documentation Feedback Analyzer 20 Hz - 20 kHz TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 SE Input and SE Output (TPA3123D2 Stereo Configuration) The SE input and output configuration is used with class-AB amplifiers. A block diagram of a fully SE measurement circuit is shown in Figure 30. SE inputs normally have one input pin per channel. In some cases, two pins are present; one is the signal and the other is ground. SE outputs have one pin driving a load through an output ac-coupling capacitor and the other end of the load is tied to ground. SE inputs and outputs are considered to be unbalanced, meaning one end is tied to ground and the other to an amplifier input/output. The generator should have unbalanced outputs, and the signal should be referenced to the generator ground for best results. Unbalanced or balanced outputs can be used when floating, but they may create a ground loop that affects the measurement accuracy. The analyzer should have balanced inputs to cancel out any common-mode noise in the measurement. Evaluation Module Audio Power Amplifier Generator Analyzer CIN VGEN RGEN RIN Lfilt CL Cfilt Twisted-Pair Wire RL RANA CANA RANA CANA Twisted-Pair Wire Figure 30. SE Input—SE Output Measurement Circuit The following general rules should be followed when connecting to APAs with SE inputs and outputs: • Use an unbalanced source to supply the input signal. • Use an analyzer with balanced inputs. • Use twisted-pair wire for all connections. • Use shielding when the system environment is noisy. • Ensure the cables from the power supply to the APA, and from the APA to the load, can handle the large currents (see Table 5). Submit Documentation Feedback 21 TPA3123D2 www.ti.com SLOS541A – JULY 2007 – REVISED AUGUST 2007 DIFFERENTIAL INPUT AND BTL OUTPUT (TPA3123D2 Mono Configuration) Many of the class-D APAs and many class-AB APAs have differential inputs and bridge-tied-load (BTL) outputs. Differential inputs have two input pins per channel and amplify the difference in voltage between the pins. Differential inputs reduce the common-mode noise and distortion of the input circuit. BTL is a term commonly used in audio to describe differential outputs. BTL outputs have two output pins providing voltages that are 180° out of phase. The load is connected between these pins. This has the added benefits of quadrupling the output power to the load and eliminating a dc-blocking capacitor. A block diagram of the measurement circuit is shown in Figure 31. The differential input is a balanced input, meaning the positive (+) and negative (–) pins have the same impedance to ground. Similarly, the SE output equates to a balanced output. Evaluation Module Audio Power Amplifier Generator CIN VGEN Analyzer Lfilt RGEN RIN Cfilt CIN Lfilt RGEN RIN RL Cfilt Twisted-Pair Wire RANA CANA RANA CANA Twisted-Pair Wire Figure 31. Differential Input, BTL Output Measurement Circuit The generator should have balanced outputs, and the signal should be balanced for best results. An unbalanced output can be used, but it may create a ground loop that affects the measurement accuracy. The analyzer must also have balanced inputs for the system to be fully balanced, thereby cancelling out any common-mode noise in the circuit and providing the most accurate measurement. The following general rules should be followed when connecting to APAs with differential inputs and BTL outputs: • Use a balanced source to supply the input signal. • Use an analyzer with balanced inputs. • Use twisted-pair wire for all connections. • Use shielding when the system environment is noisy. • Ensure that the cables from the power supply to the APA, and from the APA to the load, can handle the large currents (see Table 5). Table 5 shows the recommended wire size for the power supply and load cables of the APA system. The real concern is the dc or ac power loss that occurs as the current flows through the cable. These recommendations are based on 12-inch (30.5-cm)-long wire with a 20-kHz sine-wave signal at 25°C. Table 5. Recommended Minimum Wire Size for Power Cables 22 DC POWER LOSS (mW) AWG Size AC POWER LOSS (mW) POUT (W) RL(Ω) 10 4 18 22 16 40 18 42 2 4 18 22 3.2 8 3.7 8.5 1 8 22 28 2 8 2.1 8.1 < 0.75 8 22 28 1.5 6.1 1.6 6.2 Submit Documentation Feedback PACKAGE OPTION ADDENDUM www.ti.com 7-Aug-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TPA3123D2PWP ACTIVE HTSSOP PWP 24 TPA3123D2PWPR ACTIVE HTSSOP PWP 24 60 Lead/Ball Finish MSL Peak Temp (3) Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 4-Aug-2007 TAPE AND REEL INFORMATION Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com Device TPA3123D2PWPR 4-Aug-2007 Package Pins PWP 24 Site Reel Diameter (mm) Reel Width (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) TAI 330 16 6.95 8.3 1.6 8 TAPE AND REEL BOX INFORMATION Device Package Pins Site Length (mm) Width (mm) Height (mm) TPA3123D2PWPR PWP 24 TAI 346.0 346.0 33.0 Pack Materials-Page 2 W Pin1 (mm) Quadrant 16 Q1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Telephony www.ti.com/telephony Low Power Wireless www.ti.com/lpw Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated