STMICROELECTRONICS STM6720

STM6717/6718/6719/6720
STM6777/6778/6779/6780
Dual/triple ultra-low voltage supervisors
with push-button reset (with delay option)
Features
■
Primary supply (VCC1) monitor.
Fixed (factory-programmed) reset thresholds:
4.63 V to 1.58 V
■
Secondary supply (VCC2) monitor
(STM6717/18/19/20/77/78)
■
Fixed (factory-programmed) reset thresholds:
3.08 V to 0.79 V
■
Tertiary supply monitor (using externally
adjustable RSTIN): 0.626 V internal reference
■
RST outputs (push-pull or open drain); state
guaranteed if VCC1 or VCC2 ≥ 0.8 V
■
Reset delay time (trec) on power-up: 13.2 ms,
210 ms, 900 ms (typ)
■
Manual reset input (MR)
■
Optional delayed manual reset input (MRC)
with external capacitor (STM6777/78/79/80)
■
Low supply current - 11 µA (typ),
VCC1 = VCC2 = 3.6 V
■
Operating temperature: –40 °C to 85 °C
(industrial grade)
Table 1.
SOT23-5 (WY)
SOT23-6 (WB)
Device summary
Monitored voltages
Part
number
VCC1
VCC2
STM6717
✔
✔
✔
STM6718
✔
✔
✔
STM6719
✔
✔
✔
✔
STM6720
✔
✔
✔
✔
STM6777
✔
✔
✔
✔
STM6778
✔
✔
✔
✔
STM6779
✔
✔
✔
✔
STM6780
✔
✔
✔
✔
August 2011
RSTIN
Reset output (RST)
Manual reset Delayed MR
input (MR)
pin (MRC)
Active-low
(push-pull)
Active-low
(open drain)
✔
✔
✔
Doc ID 11469 Rev 8
WY
WY
✔
WB
WB
✔
✔
WB
WB
✔
✔
Package
WB
WB
1/30
www.st.com
1
Contents
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Contents
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1
2
Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.1.1
Active-low, push-pull reset output (RST) - STM6718/20/78/80 . . . . . . . . 7
1.1.2
Active-low, open drain reset output (RST) - STM6717/19/77/79 . . . . . . . 7
1.1.3
Push-button reset input (MR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.1.4
Manual reset delay input (MRC) - STM6777/78/79/80) . . . . . . . . . . . . . . 8
1.1.5
Primary supply voltage monitoring input (VCC1) . . . . . . . . . . . . . . . . . . . 8
1.1.6
Secondary supply voltage monitoring input (VCC2) . . . . . . . . . . . . . . . . . 8
1.1.7
Adjustable reset comparator input (RSTIN; STM6719/20/79/80) . . . . . . 8
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.1
Applications information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3
Typical operating characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4
Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
8
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2/30
Doc ID 11469 Rev 8
STM6717/6718/6719/6720/STM6777/6778/6779/6780
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Operating and AC measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
DC and AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
tMLMH minimum pulse width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SOT23-5 – 5-lead small outline transistor package mechanical data. . . . . . . . . . . . . . . . . 23
SOT23-6 – 6-lead small outline transistor package mechanical data. . . . . . . . . . . . . . . . . 24
Carrier tape dimensions for SOT23-5L and SOT23-6L . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Marking description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Doc ID 11469 Rev 8
3/30
List of figures
STM6717/6718/6719/6720/STM6777/6778/6779/6780
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Figure 29.
Figure 30.
4/30
Logic diagram (STM6717/18) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Logic diagram (STM6777/78) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Logic diagram (STM6719/20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Logic diagram (STM6779/80) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
STM6717/18 SOT23-5 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
STM6777/78 SOT23-6 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
STM6719/20 SOT23-6 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
STM6779/80 SOT23-6 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hardware hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
STM67xx interface to processor with bi-directional reset pins . . . . . . . . . . . . . . . . . . . . . . 10
Ensuring RST valid to VCC = 0 (active-low, push-pull outputs). . . . . . . . . . . . . . . . . . . . . . 10
Supply current vs. temperature (VCC1 = 5.5 V; VCC2 = 3.6 V) . . . . . . . . . . . . . . . . . . . . . . 11
Supply current vs. temperature (VCC1 = 3.6 V; VCC2 = 2.75 V) . . . . . . . . . . . . . . . . . . . . . 11
Supply current vs. temperature (VCC1 = 3.0 V; VCC2 = 2.0 V) . . . . . . . . . . . . . . . . . . . . . . 12
Supply current vs. temperature (VCC1 = 2.0 V; VCC2 = 1.0 V) . . . . . . . . . . . . . . . . . . . . . . 12
Normalized VCC reset time-out period vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Maximum VCC transient duration vs. reset threshold overdrive . . . . . . . . . . . . . . . . . . . . . 13
Normalized VRST1 threshold vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Normalized VRST2 threshold vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Reset input threshold vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
VCC1-to-reset delay vs. temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Reset input-to-reset output delay vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
MR-to-reset output delay vs. temperature (VCC1 = 3.6V) . . . . . . . . . . . . . . . . . . . . . . . . . . 16
AC testing input/output waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MR timing waveform (STM6717/18/19/20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MR timing waveform (STM6777/78/79/80) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SOT23-5 – 5-lead small outline transistor package mechanical drawing . . . . . . . . . . . . . . 23
SOT23-6 – 6-lead small outline transistor package mechanical drawing . . . . . . . . . . . . . . 24
Carrier tape for SOT23-5L and SOT23-6L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Doc ID 11469 Rev 8
STM6717/6718/6719/6720/STM6777/6778/6779/6780
1
Description
Description
The STM6717/18/19/20 and STM6777/78/79/80 supervisors are a family of low-voltage/lowsupply current processor (micro or DSP) supervisors, designed to monitor two (or three)
system power supply voltages. They are targeted at applications such as set-top boxes
(STBs), portable, battery-powered systems, networking, and communication systems.
All device options have a push-button-type manual reset input (MR). The
STM6777/78/79/80 also includes an option which enables the user to delay the start of the
manual reset process from 6 µs (MRC pin left open) or more with external capacitor. The
delay is implemented by connecting the appropriately sized capacitor between the MRC pin
and VSS (typical 4 s delay with a 3.3 µF capacitor, see Table 7 on page 21).
Two of the three supplies monitored (VCC1 and VCC2) have fixed (customer-selectable,
factory-trimmed) thresholds (VRST1 and VRST2). The third voltage is monitored using an
externally adjustable RSTIN threshold (0.626 V internal reference).
If any of the three monitored voltages drop below its factory-trimmed or adjustable
thresholds, or if MR is asserted to logic low, a RST is asserted (driven low). Once asserted,
RST is maintained at low for a minimum delay period (trec) after ALL supplies rise above
their respective thresholds and MR returns to high. These devices are guaranteed to be in
the correct reset output logic state when VCC1 and/or VCC2 is greater than 0.8 V.
These devices are available in standard 5-pin or 6-pin SOT23 packages (see Table 1 on
page 1).
Doc ID 11469 Rev 8
5/30
Description
Figure 1.
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Logic diagram (STM6717/18)
Figure 2.
Logic diagram (STM6777/78)
VCC2 VCC1
VCC2 VCC1
MRC
MR
STM6717
STM6718
STM6777
STM6778
RST
MR
VSS
RST
VSS
AI10413
Figure 3.
Logic diagram (STM6719/20)
AI10415
Figure 4.
Logic diagram (STM6779/80)
VCC
VCC2 VCC1
RSTIN
RSTIN
MR
STM6719
STM6720
MRC
RST
STM6779
STM6780
RST
MR
VSS
VSS
AI10414
Table 2.
MR
Push-button reset input
MRC
Manual reset delay input
RST
Active-low reset output
VCC1
Primary supply voltage input
VCC2
Secondary supply voltage input
RSTIN
VSS
6/30
Signal names
Adjustable reset comparator input
Ground
Doc ID 11469 Rev 8
AI10416
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Figure 5.
STM6717/18 SOT23-5 connections
RST
1
VSS
2
MR
3
5
4
Figure 6.
VCC1
VCC2
Description
STM6777/78 SOT23-6 connections
RST
1
6
VCC1
VSS
2
5
MRC
MR
3
4
VCC2
AI10417
Figure 7.
STM6719/20 SOT23-6 connections
AI10418
Figure 8.
STM6779/80 SOT23-6 connections
RST
1
6
VCC1
RST
1
6
VCC1
VSS
2
5
RSTIN
VSS
2
5
RSTIN
MR
3
4
VCC2
MR
3
4
MRC
AI10419
1.1
Pin descriptions
1.1.1
Active-low, push-pull reset output (RST) - STM6718/20/78/80
AI10420
The RST pin is driven low and stays low whenever VCC1 or VCC2 or RSTIN falls below its
factory-trimmed or adjustable reset threshold or when MR goes to logic low. It remains low
for trec after ALL supply voltages being monitored rise above their reset thresholds and MR
goes from low to high. (Push-pull outputs are referenced to VCC1.)
1.1.2
Active-low, open drain reset output (RST) - STM6717/19/77/79
The RST pin is driven low and stays low whenever VCC1 or VCC2 or RSTIN falls below its
factory-trimmed or adjustable reset threshold or when MR goes to logic low. It remains low
for trec after ALL supply voltages being monitored rise above their reset thresholds and MR
goes from low to high. Connect an external pull-up resistor to VCC1. A 10 kΩ pull-up resistor
should be sufficient for most applications.
1.1.3
Push-button reset input (MR)
When MR goes low the RST output is driven low. RST remains low as long as MR is low and
for trec after MR returns to high. This active-low input has an internal 50 kΩ pull-up resistor to
Doc ID 11469 Rev 8
7/30
Description
STM6717/6718/6719/6720/STM6777/6778/6779/6780
VCC1. It can be driven from a TTL or CMOS logic line, or with open drain/collector outputs,
or connected to VSS through a switch. If unused, leave this pin open or connect it to VCC1.
Connect a normally open momentary switch from MR to VSS; external debounce circuitry is
not required. (If MR is driven from long cables or if the device is used in noisy environments,
connecting a 0.1µF capacitor from MR to VSS provides additional noise immunity.
1.1.4
Manual reset delay input (MRC) - STM6777/78/79/80)
This pin is either left open or connected to VSS via a capacitor. By selecting the appropriate
capacitor, the manual reset process, initiated by pressing the push-button manual reset
input, can be delayed by any value from 6 µs or more (see Table 7 on page 21).
1.1.5
Primary supply voltage monitoring input (VCC1)
It also is the input for the primary reset threshold monitor. Available fixed (customerselectable, factory-programmed) reset thresholds include 4.63 V to 1.58 V.
1.1.6
Secondary supply voltage monitoring input (VCC2)
This function is available on the STM6717/18/19/20/77/78. Fixed (customer-selectable,
factory-programmed) reset thresholds include 3.08 V to 0.79 V.
1.1.7
Adjustable reset comparator input (RSTIN; STM6719/20/79/80)
This is a high impedance input. RST is driven low when the voltage at the RSTIN pin falls
below 0.626 V (internal reference voltage at this comparator). The monitored voltage reset
threshold is set with an external resistor-divider network.
Table 3.
Pin functions
Pin
8/30
Name
Function
STM6717
STM6719
STM6777
STM6779
STM6718
STM6720
STM6778
STM6780
1
1
1
1
RST
Active-low reset output
3
3
3
3
MR
Push-button reset input
—
—
5
4
MRC
Manual reset delay input
5
6
6
6
VCC1
Primary supply voltage input
4
4
4
—
VCC2
Secondary supply voltage input
—
5
—
5
2
2
2
2
RSTIN Adjustable reset comparator input
VSS
Doc ID 11469 Rev 8
Ground
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Figure 9.
Description
Block diagram
VCC1
VCC2
VRST1
COMPARE
VRST2
COMPARE
VREF/2 = 0.626
COMPARE
(1)
RSTIN(2)
VCC1
trec
Generator
RST
Logic
MR
MRC(3)
AI10421
1. VCC2 input is available on STM6717/18/19/20/77/78.
2. RSTIN available only on STM6719/20/79/80.
3. MRC available only on STM6777/78/79/80.
Figure 10. Hardware hookup
From DC/DC Converter
VCC2(1)
VCC1
VCC1
VCC3 = (626.5mV) R1 + R2
R2
(
)
0.1µF
STM67xx
VCC2
VCC3
0.1µF
R1
RSTIN(2)
RST
RST (To Processor Reset)
R2
MR
MRC(3)
Push-button
Switch
C
VSS
AI10422
1. VCC2 is available only on STM6717/18/19/20/77/78.
2. RSTIN available only on STM6719/20/79/80.
3. MRC available only on STM6777/78/79/80.
Doc ID 11469 Rev 8
9/30
Operation
STM6717/6718/6719/6720/STM6777/6778/6779/6780
2
Operation
2.1
Applications information
1.
Interfacing to processors with bi-directional reset pins
Most processors with bi-directional reset pins can interface directly to the open drain
RST outputs (STM6717/19/77/79). Systems simultaneously requiring a push-pull RST
output and a bi-directional reset interface can be in logic contention. To prevent this
contention, connect a 4.7 kΩ resistor between RST and the processor’s reset I/O as
shown in Figure 11.
2.
Ensuring a valid RST output down to VCC = 0 V
The STM67xx supervisors are guaranteed to be in the correct RST output logic state
when VCC1 and/or VCC2 is greater than 0.8 V. In applications which require valid reset
levels down to VCC = 0, a pull-down resistor to active-low outputs (push-pull only, see
Figure 12) will ensure that the reset line is valid while the reset output can no longer
sink or source current. This scheme does NOT work with the open drain outputs of the
STM6717/19/77/79.
The resistor value used is not critical, but it must be large enough not to load the reset
output when VCC is above the reset threshold. For most applications, 100 kΩ is
adequate.
Figure 11. STM67xx interface to processor with bi-directional reset pins
VCC2
VCC1
STM67xx
Processor
To other
system
components
VCC1
VCC2
RESET
RST
4.7kΩ
VSS
VSS
AI10425
Figure 12. Ensuring RST valid to VCC = 0 (active-low, push-pull outputs)
STM67xx
VCC1
VCC1
RST
VSS
R1
AI10426
10/30
Doc ID 11469 Rev 8
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Typical operating characteristics
3
Typical operating characteristics
Note:
Typical values are at TA = 25 °C unless otherwise noted.
Figure 13. Supply current vs. temperature (VCC1 = 5.5 V; VCC2 = 3.6 V)
18
Supply current (µA)
16
14
12
10
ITOTAL
ICC1
8
6
4
ICC2
2
0
–40
–20
0
20
40
60
80
Temperature (°C)
AI11843
Figure 14. Supply current vs. temperature (VCC1 = 3.6 V; VCC2 = 2.75 V)
18
16
Supply current (µA)
14
12
10
ITOTAL
8
ICC1
6
4
ICC2
2
0
–40
–20
0
20
40
Temperature (°C)
60
80
AI11844
Doc ID 11469 Rev 8
11/30
Typical operating characteristics
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Figure 15. Supply current vs. temperature (VCC1 = 3.0 V; VCC2 = 2.0 V)
18
Supply current (µA)
16
14
12
10
8
ITOTAL
6
ICC1
4
2
ICC2
0
–40
–20
0
20
40
60
80
Temperature (°C)
AI11845
Figure 16. Supply current vs. temperature (VCC1 = 2.0 V; VCC2 = 1.0 V)
18
Supply current (µA)
16
14
12
10
8
ITOTAL
6
ICC1
4
2
0
–40
ICC2
–20
0
20
40
60
80
Temperature (°C)
AI11846
12/30
Doc ID 11469 Rev 8
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Typical operating characteristics
Figure 17. Normalized VCC reset time-out period vs. temperature
1.07
Reset period
1.05
1.03
1.01
0.99
0.97
–40
–20
0
20
40
60
80
Temperature (°C)
AI11847
Maximum VCC transient duration (µs)
Figure 18. Maximum VCC transient duration vs. reset threshold overdrive
1000
100
10
1
1
10
100
1000
Reset threshold overdrive (mV)
AI11848
Doc ID 11469 Rev 8
13/30
Typical operating characteristics
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Figure 19. Normalized VRST1 threshold vs. temperature
VRST1 reset threshold
1.004
1.002
1.000
0.998
0.996
–40
–20
0
20
40
60
80
Temperature (°C)
AI11849
Figure 20. Normalized VRST2 threshold vs. temperature
VRST2 reset threshold
1.004
1.002
1.000
0.998
0.996
–40
–20
0
20
40
Temperature (°C)
14/30
Doc ID 11469 Rev 8
60
80
AI11850
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Typical operating characteristics
Figure 21. Reset input threshold vs. temperature
Reset input threshold (mV)
630
629
628
627
626
625
624
–40
–20
0
20
40
60
80
Temperature (°C)
AI11851
Figure 22. VCC1-to-reset delay vs. temperature
VCC1-to-reset delay (µs)
48
44
40
36
32
28
–40
–20
0
20
Temperature (°C)
Doc ID 11469 Rev 8
40
60
80
AI11852
15/30
Typical operating characteristics
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Figure 23. Reset input-to-reset output delay vs. temperature
RSTIN-to-reset output delay (µs)
29.0
28.5
28.0
27.5
27.0
26.5
26.0
25.5
25.0
–40
–20
0
20
40
60
80
Temperature (°C)
AI11853
Figure 24. MR-to-reset output delay vs. temperature (VCC1 = 3.6V)
MR-to-reset output delay (ns)
500
480
460
440
420
400
–40
–20
0
20
40
60
80
Temperature (°C)
AI11854
16/30
Doc ID 11469 Rev 8
STM6717/6718/6719/6720/STM6777/6778/6779/6780
4
Maximum rating
Maximum rating
Stressing the device above the rating listed in the Absolute Maximum Ratings” table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the Operating sections of
this specification is not implied. Exposure to Absolute Maximum Rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
Program and other relevant quality documents.
Table 4.
Absolute maximum ratings
Symbol
TSTG
TSLD(1)
VIO
VCC1, VCC2
Parameter
Value
Unit
–55 to 150
°C
260
°C
–0.3 to VCC1 + 0.3
V
–0.3 to VCC2 + 0.3
V
–0.3 to 7.0
V
20
mA
SOT23-5
654
mW
SOT23-6
675
mW
Storage temperature (VCC off)
Lead solder temperature for 10 seconds
Input or output voltage
Supply voltage
IIO
Input or output current (all pins)
PD
Power dissipation
1. Reflow at peak temperature of 260 °C. The time above 255 °C must not exceed 30 seconds.
Doc ID 11469 Rev 8
17/30
DC and AC parameters
5
STM6717/6718/6719/6720/STM6777/6778/6779/6780
DC and AC parameters
This section summarizes the operating measurement conditions, and the DC and AC
characteristics of the device. The parameters in the DC and AC characteristics tables that
follow, are derived from tests performed under the measurement conditions summarized in
Table 5: Operating and AC measurement conditions. Designers should check that the
operating conditions in their circuit match the operating conditions when relying on the
quoted parameters.
Table 5.
Operating and AC measurement conditions
Parameter
STM67xx
Unit
VCC supply voltage
0.8 to 5.5
V
Ambient operating temperature (TA)
–40 to 85
°C
≤5
ns
Input pulse voltages
0.2 to 0.8VCC
V
Input and output timing ref. voltages
0.3 to 0.7VCC
V
Input rise and fall times
Figure 25. AC testing input/output waveforms
0.8VCC
0.7VCC
0.3VCC
0.2VCC
AI02568
Figure 26. MR timing waveform (STM6717/18/19/20)
tMLMH
MR
tMLRL
RST
trec
AI10423a
Figure 27. MR timing waveform (STM6777/78/79/80)
tMLMH
(1)
MR
tMLRL
RST
trec
AI10424c
1. By connecting a certain capacitor between the MRC pin and VSS, the RST can be delayed from 6 µs or
more (tMLMH, see Table 7 on page 21).
18/30
Doc ID 11469 Rev 8
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Table 6.
Sym
DC and AC characteristics
Alternative
Description
VCC
Operating voltage
ICC1
VCC1 supply current
ICC2
VCC2 supply current
ILI
DC and AC parameters
(2)
ILO
0.8
Max
Unit
5.5
V
VCC1 < 5.5 V, all I/O pins open
12
35
µA
VCC1 < 3.6 V, all I/O pins open
8
23
µA
VCC2 < 3.6 V, all I/O pins open
3
9
µA
VCC2 < 2.75 V, all I/O pins open
2.5
7
µA
+1
µA
Open drain RST output
leakage current
VCC1 > VRST1, VCC2 > VRST2;
RST not asserted
0.5
µA
VCC1 or VCC2 ≥ 0.8 V,
ISINK = 1 µA, RST asserted
0.3
V
VCC1 or VCC2 ≥ 1.0 V,
ISINK = 50 µA, RST asserted
0.3
V
VCC1 or VCC2 ≥ 1.2 V,
ISINK = 100 µA, RST asserted
0.3
V
VCC1 or VCC2 ≥ 2.7 V,
ISINK = 1.2 mA, RST asserted
0.3
V
VCC1 or VCC2 ≥ 4.5 V,
ISINK = 3.2 mA, RST asserted
0.4
V
Push-pull RST rise time
(STM6718/20/78/80)
tR(3)
Typ
0 V = VIN = VCC
Output high voltage (RST;
push-pull only)
VOH
Min
Input leakage current
Output low voltage (RST;
push-pull or open drain)
VOL
Test condition(1)
–1
VCC1 ≥ 1.8 V, ISOURCE = 200 µA,
RST not asserted
0.8VCC1
V
VCC1 ≥ 2.7 V, ISOURCE = 500 µA,
RST not asserted
0.8VCC1
V
VCC1 ≥ 4.5 V, ISOURCE = 800 µA,
RST not asserted
0.8VCC1
V
Rise time measured from 10% to
90% of VCC;
CL = 5 pF, VCC = 3.3 V
5
25
ns
Reset thresholds
VRST(4)
VTH1
VCC1 reset threshold
L (falling)
4.500
4.625 4.750
V
M (falling)
4.250
4.375 4.500
V
T (falling)
3.000
3.075 3.150
V
S (falling)
2.850
2.925 3.000
V
R (falling)
2.550
2.625 2.700
V
Z (falling)
2.250
2.313 2.375
V
Y (falling)
2.125
2.188 2.250
V
W (falling)
1.620
1.665 1.710
V
V (falling)
1.530
1.575 1.620
V
Doc ID 11469 Rev 8
19/30
DC and AC parameters
Table 6.
Sym
VRST2
(4)
DC and AC characteristics (continued)
Alternative
VTH2
Description
tRD
VCC to RST delay
tRP
Test condition(1)
Min
T (falling)
3.000
3.075 3.150
V
S (falling)
2.850
2.925 3.000
V
R (falling)
2.550
2.625 2.700
V
Z (falling)
2.250
2.313 2.375
V
Y (falling)
2.125
2.188 2.250
V
W (falling)
1.620
1.665 1.710
V
V (falling)
1.530
1.575 1.620
V
I (falling)
1.350
1.388 1.425
V
H (falling)
1.275
1.313 1.350
V
G (falling)
1.080
1.110 1.140
V
F (falling)
1.020
1.050 1.080
V
K (falling)
0.895
0.925 0.955
V
J (falling)
0.845
0.875 0.905
V
E (falling)
0.810
0.833 0.855
V
D (falling)
0.765
0.788 0.810
V
VCC2 reset threshold
Reset threshold hysteresis
VHYST
trec
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Typ
Max
Unit
Referenced to VRST typical
0.5
%
VCC1 = (VRST1 + 100 mV) to
(VRST – 100 mV)
20
µs
VCC2 = (VRST2 + 75 mV) to
(VRST2 – 75 mV)
20
µs
RST pulse width
blank
140
210
280
B
8.8
13.2
17.6
G
600
900
1200
626.5
642
mV
+25
nA
ms
Adjustable reset comparator input (STM6719/20/79/80)
VRSTIN
RSTIN input threshold
611
IRSTIN
RSTIN input current
–25
RSTIN hysteresis
tRSTIND
20/30
RSTIN to RST
output delay
VRSTIN to (VRSTIN – 30 mV)
Doc ID 11469 Rev 8
3
mV
22
µs
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Table 6.
Sym
DC and AC parameters
DC and AC characteristics (continued)
Alternative
Description
Test condition(1)
Min
Typ
Max
Unit
0.3VC
V
Manual (push-button) reset input
VIL
MR input voltage
C1
VIH
MR minimum pulse width
(STM6717/18/19/20)
tMLMH
tMLRL
tMR
tMRD
MR minimum pulse width
(STM6777/78/79/80)
0.7VCC1
V
1
µs
MRC connected via
capacitor to VSS
6
µs
MR to RST output delay
200
ns
MR glitch immunity
(STM6717/18/19/20)
100
ns
MR pull-up resistance
25
50
80
kΩ
1. Valid for ambient operating temperature: TA = –40 to 85 °C; VCC1 = 0.8 to 5.5 V and VCC2 = 0.8 to 3.6 V (except where
noted).
2. Input leakage for the MRC pin is not tested.
3. Guaranteed by design.
4. The leakage current measured on the RST pin is tested with the reset de-asserted (output high impedance).
Table 7.
tMLMH minimum pulse width
Capacitor value(1)
VCC1
100 pF
0.1 µF
2.2 µF
3.3 µF
4.7 µF
6.8 µF
1.6 V
120 µs
120 ms
2.6 s
4.0 s
5.6 s
8.2 s
2.0 V
122 µs
122 ms
2.7 s
4.0 s
5.8 s
8.3 s
3.0 V
125 µs
125 ms
2.7 s
4.1 s
5.9 s
8.5 s
4.0 V
128 µs
129 ms
2.8 s
4.2 s
6.0 s
8.7 s
5.0 V
130 µs
130 ms
2.8 s
4.3 s
6.1 s
8.8 s
1. At 25 °C (typical)
Doc ID 11469 Rev 8
21/30
Package mechanical data
6
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
22/30
Doc ID 11469 Rev 8
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Package mechanical data
Figure 28. SOT23-5 – 5-lead small outline transistor package mechanical drawing
E
A1
1
e
e1
D
5x b
5x
0.20
M
CAB
C 0.10
A
A2
C
A
Datum A
0.20
θ
C
L
B
E1
Note:
0133778
Drawing is not to scale.
Table 8.
SOT23-5 – 5-lead small outline transistor package mechanical data
mm
inches
Symb
Min
Typ
Max
Min
Typ
Max
A
—
—
1.45
—
—
0.057
A1
—
—
0.15
—
—
0.006
A2
0.90
1.15
1.30
0.035
0.045
0.051
b
0.30
—
0.50
0.012
—
0.020
C
0.08
—
0.22
0.003
—
0.009
D
—
2.90
—
—
0.114
—
E
—
2.80
—
—
0.110
—
E1
—
1.60
—
—
0.063
—
e
—
0.95
—
—
0.037
—
e1
—
1.90
—
—
0.075
—
L
0.30
0.45
0.60
0.012
0.018
0.024
Q
0°
4°
8°
0°
4°
8°
N
Note:
5
5
Dimensions per JEDEC SOT/SOP product outline MO-178C, variation AA
Doc ID 11469 Rev 8
23/30
Package mechanical data
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Figure 29. SOT23-6 – 6-lead small outline transistor package mechanical drawing
E
A1
1
e
e1
D
6x b
0.10
6x
M
CAB
C 0.10
A
A2
C
A
Datum A
0.20
θ
C
L
B
E1
7049714
Note:
Drawing is not to scale.
Table 9.
SOT23-6 – 6-lead small outline transistor package mechanical data
mm
inches
Symb
Min
Typ
Max
Min
Typ
Max
A
—
—
1.45
—
—
0.057
A1
—
—
0.15
—
—
0.006
A2
0.90
1.15
1.30
0.035
0.045
0.051
b
0.30
—
0.50
0.012
—
0.020
C
0.08
—
0.22
0.003
—
0.009
D
—
2.90
—
—
0.114
—
E
—
2.80
—
—
0.110
—
E1
—
1.60
—
—
0.063
—
e
—
0.95
—
—
0.037
—
e1
—
1.90
—
—
0.075
—
L
0.30
0.45
0.60
0.012
0.018
0.024
Q
0°
4°
8°
0°
4°
8°
N
Note:
24/30
6
6
Dimensions per JEDEC SOT/SOP product outline MO-178C variation AB
Doc ID 11469 Rev 8
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Package mechanical data
Figure 30. Carrier tape for SOT23-5L and SOT23-6L
P0
E
P2
D
T
A0
F
TOP COVER
TAPE
W
B0
P1
CENTER LINES
OF CAVITY
K0
USER DIRECTION OF FEED
AM03073v1
Note:
Part pin 1 indicator is on bottom left for shipping method “F” and is on top right for shipping
method “R” see Section 7.
Table 10.
Carrier tape dimensions for SOT23-5L and SOT23-6L
Package
W
D
8.00
1.50
SOT23-5
+0.30/ +0.10/
SOT23-6
–0.10 –0.00
E
P0
P2
F
1.75
4.00
2.00
3.50
±0.10 ±0.10 ±0.10 ±0.05
A0
B0
K0
3.23
±0.10
3.17
±0.10
1.37
±0.10
Doc ID 11469 Rev 8
P1
T
Unit
Bulk
Qty
4.00 0.254
mm 3000
±0.10 ±0.013
25/30
Part numbering
STM6717/6718/6719/6720/STM6777/6778/6779/6780
7
Part numbering
Table 11.
Ordering information scheme
Example:
Device type
STM67xx
STM67xx
LT
WY
6
F
Reset thresholds (VRST1 and VRST2) for VCC1 and VCC2
STM6717/18/19/20/77/78 (VRST1 and VRST2) STM6779/80 (VRST1 only)
VRST2
Suffix VRST1
Suffix
VRST1
LT
4.625
3.075
L–(1)
4.625
3.075
MS
4.375
2.925
T–(1)
2.925
MR
4.375
2.625
S–(1)
3.075
2.313
Y–(1)
2.188
TZ(1)
TW(1)
3.075
1.665
V–(1)
1.575
TI
3.075
1.388
R–
2.625
3.075
1.110
Z–
2.313
TG(1)
TK
3.075
0.925
TE
3.075
0.833
2.925
2.188
SY(1)
2.925
1.575
SV(1)
SH(2)
2.925
1.313
2.925
1.050
SF(1)
2.925
0.875
SJ(3)
2.925
0.788
SD(3)
YV
2.188
1.575
YH
2.188
1.313
YF
2.188
1.050
YJ
2.188
0.875
YD
2.188
0.788
VH
1.575
1.313
VF
1.575
1.050
VJ
1.575
0.875
VD
1.575
0.788
Reset pulse width
blank: trec = 140 ms to 280 ms
B: trec = 8.8 ms to 17.6 ms
G: trec = 600 ms to 1200 ms
Package
WY = SOT23-5
WB = SOT23-6
Temperature range
6 = –40 to 85°C
Shipping method
E = ECOPACK® package, tubes
F = ECOPACK® package, tape and reel
R(4) = ECOPACK® package, tape and reel (pin 1 at top right).
1. These are standard versions and are typically held in stock. A non-standard version may require a higher minimum volumes, and/or longer
delivery times. For other options, or for more information on any aspect of this device, please contact the ST sales office nearest you.
2. Available in STM6719 version only.
3. Available in STM6717 version only.
4. Available for STM6720SY, STM6719SF and STM6719SFB versions only.
26/30
Doc ID 11469 Rev 8
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Table 12.
Part numbering
Marking description
Part number
VRST1 threshold (V)
VRST2 threshold (V)
Topside marking
Bottomside marking
STM6717SD
2.925
0.788
7SD1
PYWW
STM6717SJ
2.925
0.875
7SJ1
PYWW
STM6717SF
2.925
1.050
7SF1
PYWW
STM6717TG
3.075
1.110
7TG1
PYWW
STM6717TGG
3.075
1.110
7TG9
PYWW
STM6717TW
3.075
1.665
7TW1
PYWW
STM6717SV
2.925
1.575
7SV1
PYWW
STM6717SY
2.925
2.188
7SY1
PYWW
STM6717TZ
3.075
2.313
7TZ1
PYWW
STM6718SF
2.925
1.050
7SF2
PYWW
STM6718TG
3.075
1.110
7TG2
PYWW
STM6718TW
3.075
1.665
7TW2
PYWW
STM6718SV
2.925
1.575
7SV2
PYWW
STM6718SY
2.925
2.188
7SY2
PYWW
STM6718TZ
3.075
2.313
7TZ2
PYWW
STM6719SF
2.925
1.050
7SF3
PYWW
STM6719SFB
2.925
1.050
7SFB
PYWW
STM6719TG
3.075
1.110
7TG3
PYWW
STM6719SH
2.925
1.313
7SH3
PYWW
STM6719TW
3.075
1.665
7TW3
PYWW
STM6719SV
2.925
1.575
7SV3
PYWW
STM6719SY
2.925
2.188
7SY3
PYWW
STM6719TZ
3.075
2.313
7TZ3
PYWW
STM6720SF
2.925
1.050
7SF4
PYWW
STM6720TG
3.075
1.110
7TG4
PYWW
STM6720TW
3.075
1.665
7TW4
PYWW
STM6720SV
2.925
1.575
7SV4
PYWW
STM6720SY
2.925
2.188
7SY4
PYWW
STM6720TZ
3.075
2.313
7TZ4
PYWW
STM6777SF
2.925
1.050
7SF5
PYWW
STM6777TG
3.075
1.110
7TG5
PYWW
STM6777TW
3.075
1.665
7TW5
PYWW
STM6777SV
2.925
1.575
7SV5
PYWW
STM6777SY
2.925
2.188
7SY5
PYWW
STM6777TZ
3.075
2.313
7TZ5
PYWW
Doc ID 11469 Rev 8
27/30
Part numbering
Table 12.
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Marking description (continued)
Part number
VRST1 threshold (V)
VRST2 threshold (V)
Topside marking
Bottomside marking
STM6778SF
2.925
1.050
7SF6
PYWW
STM6778TG
3.075
1.110
7TG6
PYWW
STM6778TW
3.075
1.665
7TW6
PYWW
STM6778SV
2.925
1.575
7SV6
PYWW
STM6778SY
2.925
2.188
7SY6
PYWW
STM6778TZ
3.075
2.313
7TZ6
PYWW
STM6779L
4.625
—
7Lx7
PYWW
STM6779T
3.075
—
7Tx7
PYWW
STM6779S
2.925
—
7Sx7
PYWW
STM6779Y
2.188
—
7Yx7
PYWW
STM6779V
1.575
—
7Vx7
PYWW
STM6780L
4.625
—
7Lx8
PYWW
STM6780T
3.075
—
7Tx8
PYWW
STM6780S
2.925
—
7Sx8
PYWW
STM6780Y
2.188
—
7Yx8
PYWW
STM6780V
1.575
—
7Vx8
PYWW
Note:
For topside marking, “7” is the family number, followed by the VRST1 threshold, VRST2
threshold and device number (1,9 = STM6717, 2 = 6718, 3 = 6719, 4 = 6720, 5 = 6777,
6 = 6778, 7 = 6779, 8 = 6780).
For bottomside marking, “P” = assembly site, “Y” = 1-digit year, and “WW” = 2-digit work
week.
28/30
Doc ID 11469 Rev 8
STM6717/6718/6719/6720/STM6777/6778/6779/6780
8
Revision history
Revision history
Table 13.
Document revision history
Date
Revision
Changes
18-Oct-2004
1
25-Oct-2004
1.1
Descriptive text, sales types (Table 11)
14-Jan-2005
1.2
Update characteristics, pin functions (Table 2)
09-Feb-2005
1.3
Update characteristics (Figure 9; Table 3)
08-Apr-2005
1.4
Update characteristics and mechanical dimensions; add table
(Figure 9, 10, 27, 28, 29; Table 4, 6, 11, 8, 9)
28-Jul-2005
1.5
Update characteristics, reset delay (Figure 10, 27; Table 4, 6, 7, 11)
13-Sep-2005
2
Add operating characteristics; update timings, document status, Leadfree text (Figure Figure 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24,
26, 27; Table 11)
07-Oct-2005
3
Marked STM6779/6780 as availability request parts (Table 1, 11)
07-Feb-2007
4
Updated STM6779/6780 availability (cover page, Table 1, 11)
12-Jun-2007
5
Updated Table 11, added Table 12: Marking description.
05-Dec-2007
6
Updated cover page, Table 6, 11, and 12.
22-Mar-2010
7
Updated Features; Table 6, 8, 9, 11, 12; footnote 1 of Table 4;
Section 6: Package mechanical data; added tape and reel
specifications (Figure 30, Table 10, footnote 4 of Table 11);
reformatted document.
02-Aug-2011
8
Removed footnote from Table 6: DC and AC characteristics.
First draft
Doc ID 11469 Rev 8
29/30
STM6717/6718/6719/6720/STM6777/6778/6779/6780
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2011 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
30/30
Doc ID 11469 Rev 8