14 Pin DIP and SMD 5 Tap Low-Profile Fast Logic TTL Compatible Active Delay Lines Compatible with standard auto-insertable equipment and can be used in either infrared or vapor phase process. Delays are ±5% or ±2 nS† Total Tap 5, 10, 15, 20 6, 12, 18, 24 7, 14, 21, 28 8, 16, 24, 32 9, 18, 27, 36 10, 20, 30, 40 12, 24, 36, 48 15, 30, 45, 60 20, 40, 60, 80 25, 50, 75, 100 30, 60, 90, 120 35, 70, 105, 140 25 30 35 40 45 50 60 75 100 125 150 175 DIP Part Number SMD Part Number Delays are ±5% or ±2 nS† Total Tap EPA3368-25 EPA3368-30 EPA3368-35 EPA3368-40 EPA3368-45 EPA3368-50 EPA3368-60 EPA3368-75 EPA3368-100 EPA3368-125 EPA3368-150 EPA3368-175 EPA3368G-25 EPA3368G-30 EPA3368G-35 EPA3368G-40 EPA3368G-45 EPA3368G-50 EPA3368G-60 EPA3368G-75 EPA3368G-100 EPA3368G-125 EPA3368G-150 EPA3368G-175 40, 80, 120, 160 45, 90, 135, 180 50, 100, 150, 200 60, 120, 180, 240 70, 140, 210, 280 80, 160, 240, 320 84, 168, 252, 336 88, 176, 264, 352 90, 180, 270, 360 84, 188, 282, 376 100, 200, 300, 400 DC Electrical Characteristics Parameter Test Conditions EPA3368-200 EPA3368-225 EPA3368-250 EPA3368-300 EPA3368-350 EPA3368-400 EPA3368-420 EPA3368-440 EPA3368-450 EPA3368-470 EPA3368-500 EPA3368G-200 EPA3368G-225 EPA3368G-250 EPA3368G-300 EPA3368G-350 EPA3368G-400 EPA3368G-420 EPA3368G-440 EPA3368G-450 EPA3368G-470 EPA3368G-500 Schematic Min. Max. Unit VOH VOL VIK IIH High-Level Output Voltage Low-Level Output Voltage Input Clamp Voltage High-Level Input Current VCC = Min. V IL = Max. I OH = Max. 2.7 VCC = Min. VIH = Min. I OL= Max. VCC = Min. II = IIK VCC = Max. V IN = 2.7V IIL IOS Low-Level Input Current Short Circuit Output Current VCC = Max. V IN = 0.5V VCC = Max. V OUT = 0. (One output at a time) VCC = Max. V IN = OPEN VCC = Max. V IN = 0 Td ≤ 500 nS (0.75 to 2.4 Volts) Td > 500 nS VCC = Max. V OH = 2.7V VCC = Max. V OL = 0.5V ICCH High-Level Supply Current ICCL Low-Level Supply Current TRO Output Rise Time Fanout High-Level Output Fanout Low-Level Output -80 0.5 -1.2 20 V V V µA -0.6 -150 mA mA 14 12 VCC 4 10 6 8 OUTPUT INPUT 1 25 mA 40 mA 4 nS 5 nS 20 TTL LOAD 10 TTL LOAD 7 GROUND Input Pulse Test Conditions @ 25° C Recommended Operating Conditions VCC VIH VIL IIK IOH IOL PW* d* TA SMD Part Number Delay times referenced from input to leading edges at 25°C, 5.0V, with no load. †Whichever is greater. NH NL 200 225 250 300 350 400 420 440 450 470 500 DIP Part Number Min. Max. Supply Voltage High-Level Input Voltage Low-Level Input Voltage Input Clamp Current High-Level Output Current Low-Level Output Current Pulse Width of Total Delay Duty Cycle Operating Free-Air Temperature 4.75 2.0 5.25 0.8 -18 -1.0 20 20 50 +70 0 Unit V V V mA mA mA % % °C EIN PW TRI PRR VCC Pulse Input Voltage Pulse Width % of Total Delay Pulse Rise Time (0.75 - 2.4 Volts) Pulse Repetition Rate @ Td ≤ 200 nS Pulse Repetition Rate @ Td > 200 nS Supply Voltage Unit 3.2 110 2.0 1.0 100 5.0 Volts % nS MHz KHz Volts *These two values are inter-dependent. SMD Package Pin 1 I.D. PCA EPA3368G-XX Date Code .300 Typ. .019 ± .002 .270 Suggested Solder Pad Layout Pin 1 I.D. .200 PCA EPA3368-XX Date Code .300 .300 .280 Max. .100 .030 .780 Max. .010 ± .005 .010 Typ. 0°-8° .100 Typ. DSA3368G-XX & DSA3368-XX .055 .420 .200 Typ. .770 .155 DIP Package .200 .085 Typ. .035 .380 .020 Min. .200 Max. .020 Typ. .125 ± .01 Rev. - 3/18/97 Unless Otherwise Noted Dimensions in Inches Tolerances: Fractional = ± 1/32 .XX = ± .030 .XXX = ± .010 .365 Max. .010 Typ. QAF-CSO1 Rev. B 8/25/94 ELECTRONICS INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 TEL: (818) 892-0761 FAX: (818) 894-5791