AD ADG465BRM

a
FEATURES
Fault and Overvoltage Protection up to ⴞ40␣ V
Signal Paths Open Circuit with Power Off
Signal Path Resistance of RON with Power On
44 V Supply Maximum Ratings
Low On Resistance 80 ⍀ Typ
1 nA Max Path Current Leakage @ +25ⴗC
Low Power Dissipation 0.8␣ ␮W Typ
Latchup-Proof Construction
Single Channel Protector
in an SOT-23 Package
ADG465
FUNCTIONAL BLOCK DIAGRAM
VDD
VIN
VSS
VD1
VIN
VDD
APPLICATIONS
ATE Equipment
Sensitive Measurement Equipment
Hot-Insertion Rack Systems
ADC Input Channel Protection
VS1
ADG465
VOUT
VOUT
VDD
OUTPUT CLAMPED
@ VDD – 1.5V
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The ADG465 is a single channel protector in an SOT-23 package. The channel protector is placed in series with the signal
path, and will protect sensitive components from voltage transience in the signal path whether or not the power supplies are
present. Because the channel protection works regardless of the
presence of the supplies, the channel protectors are ideal for use
in applications where correct power sequencing cannot always
be guaranteed to protect analog inputs (e.g., hot-insertion rack
systems). This is discussed further, and some example circuits
are given, in the Applications section of this data sheet.
1. Fault Protection.
The ADG465 can withstand continuous voltage inputs from
–40 V to +40 V. When a fault occurs due to the power supplies being turned off, or due to an overvoltage being applied
to the ADG465, the output is clamped. When power is turned
off, current is limited to the nanoampere level.
2. Low Power Dissipation.
3. Low RON 80 Ω typ.
4. Trench Isolation Latchup-Proof Construction.
A dielectric trench separates the p- and n-channel MOSFETs
thereby preventing latchup.
A channel protector consists of an n-channel MOSFET, a
p-channel MOSFET and an n-channel MOSFET, connected in
series. The channel protector behaves like a series resistor during normal operation, i.e., (VSS + 2 V) < VIN < (VDD – 1.5 V).
When a channel’s analog input exceeds the power supplies
(including VDD and VSS = 0 V), one of the MOSFETs will
switch off, clamping the output to either VSS + 2 V or VDD – 1.5 V.
Circuitry and signal source protection is provided in the event of
an overvoltage or power loss. The channel protectors can withstand overvoltage inputs from –40 V to +40 V. See the Circuit
Information section of this data sheet.
The ADG465 can operate from both bipolar and unipolar
supplies. The channels are normally on when power is connected, and open circuit when power is disconnected. With
power supplies of ± 15 V, the on-resistance of the ADG465 is
80 Ω typ, with a leakage current of ± 1 nA max. When power
is disconnected, the input leakage current is approximately
± 5 nA typ.
The ADG465 is available in a 6-lead plastic surface mount
SOT-23 package, and an 8-lead µSOIC package.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 1998
ADG465–SPECIFICATIONS
Dual Supply1 (V
DD
= +15 V, VSS = –15 V, GND = 0 V, unless otherwise noted)
Parameter
+25ⴗC
FAULT PROTECTED CHANNEL
Fault-Free Analog Signal Range2
RON
∆RON
LEAKAGE CURRENTS
Channel Output Leakage, IS(ON)
(Without Fault Condition)
Channel Input Leakage, ID(ON)
(With Fault Condition)
Channel Input Leakage, ID(OFF)
(With Power Off and Fault)
Channel Input Leakage, ID(OFF)
(With Power Off and Output S/C)
POWER REQUIREMENTS
IDD
ISS
VDD/VSS
B
Units
Test Conditions/Comments
VSS + 1.2
VDD – 0.8
Output Open Circuit
80
95
4
115
5
V min
V max
Ω typ
Ω max
Ω max
± 0.1
±1
±1
±5
nA typ
nA max
± 0.2
±2
± 0.4
±5
nA typ
nA max
± 0.5
±2
±2
± 10
nA typ
nA max
± 0.005
± 0.015
± 0.1
± 0.5
µA typ
µA max
± 0.05
± 0.5
± 0.05
± 0.5
0
± 20
±5
±5
0
± 20
–10 V ≤ VS ≤ +10 V, IS = 1 mA
–5 V ≤ VS ≤ +5 V
VS = VD = ± 10 V
VS = ± 25 V
VD = Open Circuit
VDD = 0 V, VSS = 0 V
VS = ± 35 V
VD = Open Circuit
VDD = 0 V, VSS = 0 V
VS = ± 35 V, VD = 0 V
µA typ
µA max
µA typ
µA max
V min
V max
NOTES
1
Temperature range is as follows: B Version: –40°C to +85°C.
2
Guaranteed by design, not subject to production test.
Specifications subject to change without notice.
–2–
REV. A
ADG465
ABSOLUTE MAXIMUM RATINGS 1
PIN CONFIGURATIONS
(TA = +25°C unless otherwise noted)
VDD to VSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +44 V
VS, VD, Analog Input Overvoltage with Power ON2
. . . . . . . . . . . . . . . . . . . . . . . . . VSS – 20 V to VDD + 20 V
VS, VD, Analog Input Overvoltage with Power OFF2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –35 V to +35 V
Continuous Current, S or D . . . . . . . . . . . . . . . . . . . . . 20 mA
Peak Current, S or D . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA
(Pulsed at 1 ms, 10% Duty Cycle Max)
Operating Temperature Range
Industrial (B Version) . . . . . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +125°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
SOT-23 Package
θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . . 230°C/W
µSOIC Package
θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . . 205°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . +215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability. Only one absolute
maximum rating may be applied at any one time.
2
Overvoltages at S or D will be clamped by the channel protector, see Circuit
Information section of the data sheet.
(RT-6)
VD1 1
NC 2
ADG465
(RM-8)
6 VDD
NC 1
5 NC
VDD 2
TOP VIEW
VSS 3 (Not to Scale) 4 VS1
8 NC
ADG465
7 VD1
TOP VIEW
VS1 3 (Not to Scale) 6 VSS
NC 4
NC = NO CONNECT
5 NC
NC = NO CONNECT
PIN FUNCTION DESCRIPTIONS
Pin
Pin
RT-6 RM-8 Pin Description
1
7
2
3
1, 4
6
4
3
5
6
5, 8
2
VD1, this is one terminal of the channel protector. The channel protector is bidirectional so this
terminal may be used as an input or an output.
NC, this is a no connect pin.
VSS, Negative Power Supply (0 V to –20 V).
The clamping point for a negative overvoltage is
also defined by VSS, see Overvoltage Protection
section.
VS1, this is one terminal of the channel protector. The channel protector is bidirectional so this
terminal may be used as an output or an input.
NC, this is a no connect pin.
VDD, Positive Power Supply (0 V to 20 V). The
clamping point for a positive overvoltage is also
defined by VDD, see Overvoltage Protection
section.
ORDERING GUIDE
Model
Temperature Range
Package Descriptions
Brand
Package Options
ADG465BRT
ADG465BRM
–40°C to +85°C
–40°C to +85°C
6-Lead Plastic Surface Mount SOT-23
8-Lead µSOIC
S1B
S1B
RT-6
RM-8
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADG465 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
REV. A
–3–
WARNING!
ESD SENSITIVE DEVICE
ADG465 —Typical Performance Characteristics
140
POSITIVE OVERVOLTAGE ON INPUT
RLOAD = 100kV
CLOAD = 100pF
–5V TO +15V
VDD = +10V
STEP INPUT
VSS = –10V
TEMP = +258C
130
120
15
VDD = +5V
VSS = –5V
100
10
90
VDD = +10V
VSS = –10V
80
70
Volts
RON – V
110
VDD = +16.5V
VSS = –16.5V
CHANNEL PROTECTOR
OUTPUT
0
–5
60
50
–10
5
–5
0
VD, VS – Volts
10
5
Ch1
5.00V
Ch2
5.00V
M50.0ns
Ch1
500mV
Figure 3. Positive Overvoltage Transience Response
Figure 1. On Resistance as a Function of VDD and VD
(Input Voltage)
125
115
NEGATIVE OVERVOLTAGE ON INPUT
VDD = +15V
VSS = –15V
5
0
95
+1258C
85
+808C
Volts
RON – V
105
RLOAD = 100kV
CLOAD = 100pF
VDD = +10V
VSS = –10V
CHANNEL PROTECTOR
OUTPUT
–5
–10
–15
75
+258C
65
5V TO –15V
STEP INPUT
55
45
–10
–5
0
VD, VS – Volts
5
10
Ch1
5.00V
Ch2
5.00V
M50.0ns
Ch1
500mV
Figure 4. Negative Overvoltage Transience Response
Figure 2. On Resistance as a Function of Temperature
and VD (Input Voltage)
10V TO +10V INPUT
RLOAD = 100kV
VDD = +5V
VSS = –5V
20V
10
VCLAMP = 4.5V
OUTPUT
20
VCLAMP = 4V
Ch1
5.00V
Ch2
5.00V
M100ns
Ch1
500mV
Figure 5. Overvoltage Ramp
–4–
REV. A
ADG465
CIRCUIT INFORMATION
VSS – VTP where VTP is the threshold voltage of the PMOS
device (2␣ V typ). If the input voltage exceeds these threshold
voltages, the output of the channel protector (no load) is
clamped at these threshold voltages. However, the channel
protector output will clamp at a voltage inside these thresholds
if the output is loaded. For example, with an output load of
1␣ kΩ, VDD = 15␣ V and a positive overvoltage. The output will
clamp at VDD – VTN – ∆V = 15␣ V – 1.5␣ V – 0.6␣ V = 12.9␣ V
where ∆V is due to I. R voltage drops across the channels of the
MOS devices (see Figure 8). As can be seen from Figure 8, the
current during fault condition is determined by the load on the
output (i.e., VCLAMP/RL). However, if the supplies are off, the
fault current is limited to the nanoampere level.
Figure 6 below shows a simplified schematic of a channel protector circuit. The circuit is comprised of four MOS transistors—two NMOS and two PMOS. One of the PMOS devices
does not lie directly in the signal path, but is used to connect the
source of the second PMOS device to its backgate. This has the
effect of lowering the threshold voltage and increasing the
input signal range of the channel for normal operation. The
source and backgate of the NMOS devices are connected for the
same reason. During normal operation the channel protectors
have a resistance of 80␣ Ω typ. The channel protectors are very
low power devices; even under fault conditions the supply current is limited to sub-microampere levels. All transistors are
dielectrically isolated from each other using a trench isolation
method. This makes it impossible to latch up the channel protectors. For an explanation, see Trench Isolation section.
Figures 7, 9 and 10 show the operating conditions of the signal
path transistors during various fault conditions. Figure 7 shows
how the channel protectors operate when a positive overvoltage
is applied to the channel protector.
VDD – VTN*
(+13.5V)
VSS
PMOS
NMOS
POSITIVE
OVERVOLTAGE
(+20V)
NMOS
NMOS
PMOS
NONSATURATED
SATURATED
PMOS
VDD
VDD (+15V)
VSS
VDD
The first NMOS transistor goes into a saturated mode of operation as the voltage on its Drain exceeds the Gate voltage (VDD) –
the threshold voltage (VTN). This situation is shown in Figure 8.
The potential at the source of the NMOS device is equal to VDD
–VTN. The other MOS devices are in a nonsaturated mode of
operation.
When a fault condition occurs on the input of a channel protector, the voltage on the input has exceeded some threshold
voltage set by the supply rail voltages. The threshold voltages
are related to the supply rails as follows: for a positive overvoltage, the threshold voltage is given by VDD – VT where VTN is the
threshold voltage of the NMOS transistor (1.5␣ V typ). In the
case of a negative overvoltage the threshold voltage is given by
VG
DV
VS
(+13.5V)
(VDD = +15V)
PMOS
OVERVOLTAGE
OPERATION
(SATURATED)
N+
EFFECTIVE
SPACE CHARGE
REGION
VT = 1.5V
P–
N+
N+
NMOS
NONSATURATED
OPERATION
RL
N-CHANNEL
(VG – VT = 13.5V)
IOUT
Figure 8. Positive Overvoltage Operation on the Channel Protector
REV. A
VDD (+15V)
Figure 7. Positive Overvoltage on the Channel Protector
Overvoltage Protection
VD
NONSATURATED
*VTN = NMOS THRESHOLD VOLTAGE (+1.5V)
Figure 6. The Channel Protector Circuit
(+20V)
VSS (–15V)
NMOS
–5–
VCLAMP
ADG465
When a negative overvoltage is applied to the channel protector
circuit, the PMOS transistor enters a saturated mode of operation
as the drain voltage exceeds VSS – VTP. See Figure 9 below. As in
the case of the positive overvoltage, the other MOS devices are
nonsaturated.
NEGATIVE
OVERVOLTAGE
(–20V)
NEGATIVE
OVERVOLTAGE
(–20V)
NMOS
NONSATURATED
VDD (+15V)
TRENCH ISOLATION
The MOS devices that make up the channel protector are
isolated from each other by an oxide layer (trench) (see Figure
11). When the NMOS and PMOS devices are not electrically
isolated from each other, there exists the possibility of “latchup”
caused by parasitic junctions between CMOS transistors. Latchup
is caused when P-N junctions that are normally reverse biased,
become forward biased, causing large currents to flow. This can
be destructive.
VSS – VTP*
(–13V)
PMOS
NMOS
SATURATED
VSS (–15V)
CMOS devices are normally isolated from each other by
Junction Isolation. In Junction Isolation, the N and P wells of the
CMOS transistors form a diode that is reverse biased under
normal operation. However, during overvoltage conditions, this
diode becomes forward biased. A Silicon-Controlled Rectifier
(SCR) type circuit is formed by the two transistors, causing a
significant amplification of the current that, in turn, leads to
latchup. With Trench Isolation, this diode is removed; the result
is a latchup-proof circuit.
NONSATURATED
VDD (+15V)
*VTP = PMOS THRESHOLD VOLTAGE (+2V)
Figure 9. Negative Overvoltage on the Channel Protector
The channel protector is also functional when the supply rails
are down (e.g., power failure) or momentarily unconnected
(e.g., rack system). This is where the channel protector has an
advantage over more conventional protection methods such as
diode clamping (see Applications Information). When VDD and
VSS equal 0␣ V, all transistors are off and the current is limited to
microampere levels (see Figure 10).
VG
VS
T
R
E
N
C
H
(0V)
P+
N–
VG
VD
P-CHANNEL
P+
VS
T
R
E
N
C
H
N+
VD
N-CHANNEL
P–
N+
T
R
E
N
C
H
BURIED OXIDE LAYER
POSITIVE OR
NEGATIVE
OVERVOLTAGE
NMOS
PMOS
SUBSTRATE (BACKGATE)
NMOS
OFF
OFF
OFF
VDD (0V)
VSS (0V)
VDD (0V)
Figure 11. Trench Isolation
Figure 10. Channel Protector Supplies Equal to Zero Volts
–6–
REV. A
ADG465
APPLICATIONS INFORMATION
Overvoltage and Power Supply Sequencing Protection
The ADG465 is ideal for use in applications where input overvoltage protection is required and correct power supply sequencing
cannot always be guaranteed. The overvoltage protection ensures that the output voltage of the channel protector will not
exceed the threshold voltages set by the supplies (see Circuit
Information section) when there is an overvoltage on the input.
When the input voltage does not exceed these threshold voltages, the channel protector behaves like a series resistor (80␣ Ω
typ). The resistance of the channel protector does vary slightly
with operating conditions (see Typical Performance Graphs).
The power sequencing protection is afforded by the fact that
when the supplies to the channel protector are not connected,
the channel protector becomes a high resistance device. Under
this condition all transistors in the channel protector are off and
the only currents that flow are leakage currents, which are at the
µA level.
EDGE
CONNECTOR
VDD
+5V
VSS
–5V
ANALOG IN
–2.5V TO +2.5V
ADC
ADG465
LOGIC
LOGIC
CONTROL
LOGIC
channel protectors. In this way, the outputs of the channel
protectors are clamped well below VDD and VSS until the
capacitors are charged. The diodes ensure that the supplies on
the channel protector never exceed the supply rails of the board
when it is being disconnected. Again, this ensures that signals
on the inputs of the CMOS devices never exceed the supplies.
High Voltage Surge Suppression
The ADG465 are not intended for use in high voltage applications such as surge suppression. The ADG465 has breakdown
voltages of VSS – 20 V and VDD + 20 V on the inputs when the
power supplies are connected. When the power supplies are
disconnected, the breakdown voltages on the input of the channel protector are ± 35␣ V. In applications where inputs are likely
to be subject to overvoltages exceeding the breakdown voltages
quoted for the channel protectors, transient voltage suppressors
(TVSs) should be used. These devices are commonly used to
protect vulnerable circuits from electric overstress such as that
caused by electrostatic discharge, inductive load switching and
induced lightning. However, TVSs can have a substantial
standby (leakage) current (300␣ µA typ) at the reverse standoff
voltage. The reverse standoff voltage of a TVS is the normal
peak operating voltage of the circuit. In addition, TVSs offer no
protection against latchup of sensitive CMOS devices when the
power supplies are off. To provide the best leakage current
specification and circuit protection, the best solution is to use a
channel protector in conjunction with a TVS.
Figure 13 shows an input protection scheme that uses both a
TVS and channel protector. The TVS is selected with a reverse
standoff voltage much greater than the operating voltage of the
circuit (TVSs with higher breakdown voltages tend to have
better standby leakage current specifications), but inside
the breakdown voltage of the channel protector. This circuit
protects the circuitry whether or not the power supplies are
present.
GND
VDD = +5V
VSS = –5V
Figure 12. Overvoltage and Power Supply Sequencing
Protection
ADG465
Figure 12 shows a typical application requiring overvoltage and
power supply sequencing protection. The application shows a
Hot-Insertion rack system. This involves plugging a circuit
board or module into a live rack via an edge connector. In this
type of application it is not possible to guarantee correct power
supply sequencing. Correct power supply sequencing means that
the power supplies should be connected prior to any external
signals. Incorrect power sequencing can cause a CMOS device
to “latch up,” see Trench Isolation section. This is true of most
CMOS devices, regardless of the functionality. RC networks
are used on the supplies of the channel protector (Figure 12)
to ensure that the rest of the circuitry is powered up before the
REV. A
ADC
TVSs
BREAKDOWN
VOLTAGE = 20V
Figure 13. High Voltage Protection
–7–
ADG465
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
C2217a–0–9/98
6-Lead Plastic Surface Mount SOT-23 Package
(RT-6)
0.122 (3.10)
0.106 (2.70)
0.071 (1.80)
0.059 (1.50)
6
5
4
1
2
3
0.118 (3.00)
0.098 (2.50)
PIN 1
0.037 (0.95) BSC
0.075 (1.90)
BSC
0.051 (1.30)
0.035 (0.90)
0.057 (1.45)
0.035 (0.90)
0.020 (0.50) SEATING
0.010 (0.25) PLANE
0.006 (0.15)
0.000 (0.00)
108
0.009 (0.23) 08
0.003 (0.08)
0.022 (0.55)
0.014 (0.35)
8-Lead ␮SOIC
(RM-8)
0.122 (3.10)
0.114 (2.90)
8
5
0.199 (5.05)
0.187 (4.75)
0.122 (3.10)
0.114 (2.90)
1
4
PIN 1
0.0256 (0.65) BSC
0.120 (3.05)
0.112 (2.84)
0.043 (1.09)
0.037 (0.94)
0.006 (0.15)
0.002 (0.05)
0.018 (0.46)
0.008 (0.20)
0.011 (0.28)
0.003 (0.08)
33°
27°
0.028 (0.71)
0.016 (0.41)
PRINTED IN U.S.A.
SEATING
PLANE
0.120 (3.05)
0.112 (2.84)
–8–
REV. A