TI SN74AVCB164245VR

SN74AVCB164245
16-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES394D – JUNE 2002 – REVISED JUNE 2005
•
FEATURES
•
•
•
•
•
Member of the Texas Instruments Widebus™
Family
DOC™ Circuitry Dynamically Changes Output
Impedance, Resulting in Noise Reduction
Without Speed Degradation
Dynamic Drive Capability Is Equivalent to
Standard Outputs With IOH and IOL of ±24 mA
at 2.5-V VCC
Control Inputs VIH/VIL Levels Are Referenced
to VCCB Voltage
If Either VCC Input Is at GND, Both Ports Are in
the High-Impedance State
•
•
•
•
Overvoltage-Tolerant Inputs/Outputs Allow
Mixed-Voltage-Mode Data Communications
Ioff Supports Partial-Power-Down Mode
Operation
Fully Configurable Dual-Rail Design Allows
Each Port to Operate Over Full 1.4-V to 3.6-V
Power-Supply Range
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Protection Exceeds JESD 22
– 2000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
– 1000-V Charged-Device Model (C101)
DESCRIPTION
This 16-bit (dual-octal) noninverting bus transceiver uses two separate configurable power-supply rails. The
A port is designed to track VCCA. VCCA accepts any supply voltage from 1.4 V to 3.6 V. The B port is designed to
track VCCB. VCCB accepts any supply voltage from 1.4 V to 3.6 V. This allows for universal low-voltage
bidirectional translation between any of the 1.5-V, 1.8-V, 2.5-V, and 3.3-V voltage nodes.
The SN74AVCB164245 is designed for asynchronous communication between data buses. The device transmits
data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the
direction-control (DIR) input. The output-enable (OE) input can be used to disable the outputs so the buses are
effectively isolated.
The SN74AVCB164245 is designed so that the control pins (1DIR, 2DIR, 1OE, and 2OE) are supplied by VCCB.
To ensure the high-impedance state during power up or power down, OE should be tied to VCCB through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down. If either VCC input is at GND,
both ports are in the high-impedance state.
ORDERING INFORMATION
PACKAGE (1)
TA
–40°C to 85°C
(1)
ORDERABLE PART NUMBER
FBGA – GRD
Tape and reel
74AVCB164245GRDR
FBGA – ZRD (Pb-Free)
Tape and reel
74AVCB164245ZRDR
TSSOP – DGG
Tape and reel
SN74AVCB164245GR
TVSOP – DGV
Tape and reel
SN74AVCB164245VR
VFBGA – GQL
Tape and reel
SN74AVCB164245KR
VFBGA – ZQL (Pb-Free)
Tape and reel
74AVCB164245ZQLR
TOP-SIDE MARKING
WB4245
AVCB164245
WB4245
WB4245
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus, DOC are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2002–2005, Texas Instruments Incorporated
SN74AVCB164245
16-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
SCES394D – JUNE 2002 – REVISED JUNE 2005
TERMINAL ASSIGNMENTS
DGG OR DGV PACKAGE
(TOP VIEW)
1DIR
1B1
1B2
GND
1B3
1B4
VCCB
1B5
1B6
GND
1B7
1B8
2B1
2B2
GND
2B3
2B4
VCCB
2B5
2B6
GND
2B7
2B8
2DIR
2
1
48
2
47
3
46
4
45
5
44
6
43
7
42
8
41
9
40
10
39
11
38
12
37
13
36
14
35
15
34
16
33
17
32
18
31
19
30
20
29
21
28
22
27
23
26
24
25
1OE
1A1
1A2
GND
1A3
1A4
VCCA
1A5
1A6
GND
1A7
1A8
2A1
2A2
GND
2A3
2A4
VCCA
2A5
2A6
GND
2A7
2A8
2OE
www.ti.com
SN74AVCB164245
16-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES394D – JUNE 2002 – REVISED JUNE 2005
TERMINAL ASSIGNMENTS
(56-Ball GQL/ZQL Package) (1)
GQL OR ZQL PACKAGE
(TOP VIEW)
1 2 3 4 5 6
A
B
C
D
E
F
G
H
J
K
(1)
1
2
3
4
5
6
A
1DIR
NC
NC
NC
NC
1OE
B
1B2
1B1
GND
GND
1A1
1A2
C
1B4
1B3
VCCB
VCCA
1A3
1A4
D
1B6
1B5
GND
GND
1A5
1A6
E
1B8
1B7
1A7
1A8
F
2B1
2B2
2A2
2A1
G
2B3
2B4
GND
GND
2A4
2A3
H
2B5
2B6
VCCB
VCCA
2A6
2A5
J
2B7
2B8
GND
GND
2A8
2A7
K
2DIR
NC
NC
NC
NC
2OE
NC - No internal connection
GRD OR ZRD PACKAGE
(TOP VIEW)
1
2
3
4
5
6
TERMINAL ASSIGNMENTS
(54-Ball GRD/ZRD Package) (1)
A
B
1
2
3
4
5
6
A
1B1
NC
1DIR
1OE
NC
1A1
B
1B3
1B2
NC
NC
1A2
1A3
C
1B5
1B4
VCCB
VCCA
1A4
1A5
C
D
1B7
1B6
GND
GND
1A6
1A7
D
E
2B1
1B8
GND
GND
1A8
2A1
E
F
G
H
(1)
F
2B3
2B2
GND
GND
2A2
2A3
G
2B5
2B4
VCCB
VCCA
2A4
2A5
H
2B7
2B6
NC
NC
2A6
2A7
J
2B8
NC
2DIR
2OE
NC
2A8
NC - No internal connection
xxxxx
J
xxxxx
xxxxx
xxxxx
xxxxx
FUNCTION TABLE
(EACH 8-BIT SECTION)
INPUTS
OPERATION
OE
DIR
L
L
B data to A bus
L
H
A data to B bus
H
X
Isolation
3
SN74AVCB164245
16-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES394D – JUNE 2002 – REVISED JUNE 2005
LOGIC DIAGRAM (POSITIVE LOGIC)
1DIR
1
2DIR
48
1A1
25
1OE
47
2A1
2
24
2OE
36
13
1B1
2B1
To Seven Other Channels
To Seven Other Channels
Pin numbers shown are for the DGG and DGV packages.
Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
VCCA
VCCB
VI
MIN
MAX
–0.5
4.6
I/O ports (A port)
–0.5
4.6
I/O ports (B port)
–0.5
4.6
Control inputs
–0.5
4.6
A port
–0.5
4.6
B port
–0.5
4.6
A port
–0.5 VCCA + 0.5
B port
–0.5 VCCB + 0.5
Supply voltage range
Input voltage
range (2)
UNIT
V
V
VO
Voltage range applied to any output in the high-impedance or
power-off state (2)
VO
Voltage range applied to any output in the high or low state (2) (3)
IIK
Input clamp current
VI < 0
–50
mA
IOK
Output clamp current
VO < 0
–50
mA
IO
Continuous output current
50
mA
100
mA
Continuous current through VCCA, VCCB, or GND
θJA
Package thermal impedance (4)
Tstg
Storage temperature range
DGG package
70
DGV package
58
GQL/ZQL package
28
GRD/ZRD package
(1)
(2)
(3)
(4)
4
V
V
°C/W
36
–65
150
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed.
The output positive-voltage rating may be exceeded up to 4.6 V maximum if the output current rating is observed.
The package thermal impedance is calculated in accordance with JESD 51-7.
www.ti.com
SN74AVCB164245
16-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
SCES394D – JUNE 2002 – REVISED JUNE 2005
Recommended Operating Conditions
(1) (2) (3)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VCCA
Supply voltage
VCCI
1.4
3.6
V
VCCB
Supply voltage
1.4
3.6
V
VIH
High-level input voltage
VIL
Low-level input voltage
VIH
High-level input voltage
VIL
Low-level input voltage
VI
Input voltage
VO
Output voltage
IOH
Data inputs
Data inputs
Control inputs
(referenced to VCCB)
Control inputs
(referenced to VCCB)
VCCI × 0.65
1.95 V to 2.7 V
1.7
2.7 V to 3.6 V
2
1.4 V to 1.95 V
VCCI × 0.35
1.95 V to 2.7 V
0.7
2.7 V to 3.6 V
0.8
1.4 V to 1.95 V
VCCB × 0.65
1.95 V to 2.7 V
1.7
2.7 V to 3.6 V
2
1.4 V to 1.95 V
VCCB × 0.35
1.95 V to 2.7 V
0.7
2.7 V to 3.6 V
0.8
0
VCCO
3-state
0
3.6
Input transition rise or fall rate
TA
Operating free-air temperature
1.4 V to 1.6 V
–2
1.65 V to 1.95 V
–4
2.3 V to 2.7 V
–8
3 V to 3.6 V
–12
1.4 V to 1.6 V
2
1.65 V to 1.95 V
4
2.3 V to 2.7 V
8
3 V to 3.6 V
12
–40
V
V
Active state
Low-level output current
UNIT
V
3.6
∆t/∆v
(1)
(2)
(3)
1.4 V to 1.95 V
0
High-level output current
IOL
VCCO
V
V
V
mA
mA
5
ns/V
85
°C
VCCI is the VCC associated with the data input port.
VCCO is the VCC associated with the data output port.
All unused data inputs of the device must be held at VCCI or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
5
SN74AVCB164245
16-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES394D – JUNE 2002 – REVISED JUNE 2005
Electrical Characteristics (1) (2)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
VOH
VOL
II
Control inputs
A port
Ioff
B port
TEST CONDITIONS
B port
A port
ICCA
MIN TYP (3)
MAX
VI = VIH
1.4 V to 3.6 V
1.4 V to 3.6 V
IOH = –2 mA
VI = VIH
1.4 V
1.4 V
IOH = –4 mA
VI = VIH
1.65 V
1.65 V
1.2
IOH = –8 mA
VI = VIH
2.3 V
2.3 V
1.75
IOH = –12 mA
VI = VIH
3V
3V
2.3
IOH = 100 µA
VI = VIL
1.4 V to 3.6 V
1.4 V to 3.6 V
0.2
IOH = 2 mA
VI = VIL
1.4 V
1.4 V
0.35
IOH = 4 mA
VI = VIL
1.65 V
1.65 V
0.45
IOH = 8 mA
VI = VIL
2.3 V
2.3 V
0.55
IOH = 12 mA
VI = VIL
3V
3V
0.7
1.4 V to 3.6 V
3.6 V
±2.5
0V
0 to 3.6 V
±10
0 to 3.6 V
0V
±10
3.6 V
3.6 V
±12.5
0V
3.6 V
±12.5
3.6 V
0V
±12.5
1.6 V
1.6 V
20
1.95 V
1.95 V
20
2.7 V
2.7 V
30
0V
3.6 V
–40
3.6 V
0V
40
3.6 V
3.6 V
40
VI = VCCB or GND
VI or VO = 0 to 3.6 V
VO = VCCO or GND,
VI = VCCI or GND
VI = VCCI or GND,
ICCB
VCCB
IOH = –100 µA
A or B ports
IOZ (4)
VCCA
VI = VCCI or GND,
OE = VIH
OE = don't
care
IO = 0
IO = 0
UNIT
VCCO – 0.2
1.05
V
1.6 V
1.6 V
20
1.95 V
1.95 V
20
2.7 V
2.7 V
30
0V
3.6 V
40
3.6 V
0V
–40
3.6 V
3.6 V
40
V
µA
µA
µA
µA
µA
Ci
Control inputs
VI = 3.3 V or GND
3.3 V
3.3 V
4
pF
Cio
A or B ports
VO = 3.3 V or GND
3.3 V
3.3 V
5
pF
(1)
(2)
(3)
(4)
6
VCCO is the VCC associated with the output port.
VCCI is the VCC associated with the input port.
All typical values are at TA = 25°C.
For I/O ports, the parameter IOZ includes the input leakage current.
SN74AVCB164245
16-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES394D – JUNE 2002 – REVISED JUNE 2005
Switching Characteristics
over recommended operating free-air temperature range, VCCA = 1.5 V ± 0.1 V (see Figure 2)
PARAMETER
tpd
FROM
(INPUT)
TO
(OUTPUT)
A
B
ten
OE
tdis
OE
VCCB = 1.5 V
0.1 V
VCCB = 1.8 V
0.15 V
VCCB = 2.5 V
0.2 V
VCCB = 3.3 V
0.3 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
B
1.7
6.7
1.9
6.3
1.8
5.5
1.7
5.8
A
1.8
6.8
2.2
7.4
2.1
7.6
2.1
7.3
A
2.5
8.4
2.4
7.4
2.1
5.2
1.9
4.2
B
2.1
9
2.9
9.8
3.2
10
3
9.8
A
2.2
6.9
2.3
6.1
1.3
3.6
1.3
3
B
2.1
7.1
2.3
6.4
1.7
5.1
1.6
4.8
UNIT
ns
ns
ns
Switching Characteristics
over recommended operating free-air temperature range, VCCA = 1.8 V ± 0.15 V (see Figure 2)
PARAMETER
tpd
FROM
(INPUT)
TO
(OUTPUT)
A
B
ten
OE
tdis
OE
VCCB = 1.5 V
0.1 V
VCCB = 1.8 V
0.15 V
VCCB = 2.5 V
0.2 V
VCCB = 3.3 V
0.3 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
B
1.7
6.7
1.8
6
1.7
4.7
1.6
4.3
A
1.4
5.5
1.8
6
1.8
5.8
1.8
5.5
A
2.6
8.5
2.5
7.5
2.2
5.3
1.9
4.2
B
1.8
7.6
2.6
7.7
2.6
7.6
2.6
7.4
A
2.3
7
2.3
6.1
1.3
3.6
1.3
3
B
1.8
7
2.5
6.3
1.8
4.7
1.7
4.4
UNIT
ns
ns
ns
Switching Characteristics
over recommended operating free-air temperature range, VCCA = 2.5 V ± 0.2 V (see Figure 2)
PARAMETER
tpd
FROM
(INPUT)
TO
(OUTPUT)
A
B
B
A
ten
OE
tdis
OE
VCCB = 1.5 V
0.1 V
MIN
VCCB = 1.8 V
0.15 V
VCCB = 2.5 V
0.2 V
VCCB = 3.3 V
0.3 V
MAX
MIN
MAX
MIN
MAX
MIN
MAX
1.6
6
1.8
5.6
1.5
4
1.4
3.4
1.3
4.6
1.7
4.4
1.5
4
1.4
3.7
A
3.1
8.5
2.5
7.5
2.2
5.3
1.9
4.2
B
1.7
5.7
2.2
5.5
2.2
5.3
2.2
5.1
A
2.4
7
3
6.1
1.4
3.6
1.2
3
B
1.2
5.8
1.9
5
1.4
3.6
1.3
3.3
UNIT
ns
ns
ns
Switching Characteristics
over recommended operating free-air temperature range, VCCA = 3.3 V ± 0.3 V (see Figure 2)
PARAMETER
tpd
FROM
(INPUT)
TO
(OUTPUT)
A
B
ten
OE
tdis
OE
VCCB = 1.5 V
0.1 V
VCCB = 1.8 V
0.15 V
VCCB = 2.5 V
0.2 V
VCCB = 3.3 V
0.3 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
B
1.5
5.9
1.7
5.4
1.5
3.7
1.4
3.1
A
1.3
4.5
1.6
3.8
1.5
3.3
1.4
3.1
A
2.6
8.3
2.5
7.4
2.2
5.2
1.9
4.1
B
1.6
4.9
2
4.5
2
4.3
1.9
4.1
A
2.3
7
3
6
1.3
3.5
1.2
3.5
B
1.3
6.9
2.1
5.5
1.6
3.8
1.5
3.5
UNIT
ns
ns
ns
7
SN74AVCB164245
16-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES394D – JUNE 2002 – REVISED JUNE 2005
Operating Characteristics
VCCA and VCCB = 3.3 V, TA = 25°C
PARAMETER
TEST CONDITIONS
Power dissipation capacitance per transceiver,
A-port input, B-port output
CpdA
(VCCA)
CpdB
(VCCB)
TYP
Outputs enabled
Outputs disabled
CL = 0,
7
f = 10 MHz
Power dissipation capacitance per transceiver,
B-port input, A-port output
Outputs enabled
Outputs disabled
7
Power dissipation capacitance per transceiver,
A-port input, B-port output
Outputs enabled
20
Power dissipation capacitance per transceiver,
B-port input, A-port output
Outputs enabled
Outputs disabled
UNIT
14
CL = 0,
20
7
f = 10 MHz
14
Outputs disabled
pF
pF
7
Output Description
The DOC™ circuitry is implemented, which, during the transition, initially lowers the output impedance to
effectively drive the load and, subsequently, raises the impedance to reduce noise. Figure 1 shows typical VOL vs
IOL and VOH vs IOH curves to illustrate the output impedance and drive capability of the circuit. At the beginning of
the signal transition, the DOC circuit provides a maximum dynamic drive that is equivalent to a high-drive
standard-output device. For more information, refer to the TI application reports, AVC Logic Family Technology
and Applications, literature number SCEA006, and Dynamic Output Control (DOC™) Circuitry Technology and
Applications, literature number SCEA009.
3.2
TA = 25°C
Process = Nominal
− Output Voltage − V
2.8
2.4
VCC = 3.3 V
2.0
1.6
VCC = 2.5 V
1.2
OH
VCC = 1.8 V
0.8
V
VOL − Output Voltage − V
2.8
TA = 25°C
Process = Nominal
2.4
2.0
1.6
1.2
0.8
VCC = 3.3 V
0.4
0.4
0
17
34
51
68
85 102 119
IOL − Output Current − mA
136
153
170
VCC = 2.5 V
−160 −144 −128 −112 −96 −80 −64 −48
IOH − Output Current − mA
Figure 1. Typical Output Voltage vs Output Current
8
VCC = 1.8 V
−32 −16
0
SN74AVCB164245
16-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES394D – JUNE 2002 – REVISED JUNE 2005
PARAMETER MEASUREMENT INFORMATION
2 × VCCO
S1
RL
From Output
Under Test
Open
GND
CL
(see Note A)
TEST
S1
tpd
tPLZ/tPZL
tPHZ/tPZH
Open
2 × VCCO
GND
RL
tw
LOAD CIRCUIT
VCCI
VCCI/2
Input
VCCO
CL
RL
VTP
1.5 V ± 0.1 V
1.8 V ± 0.15 V
2.5 V ± 0.2 V
3.3 V ± 0.3 V
15 pF
30 pF
30 pF
30 pF
2 kΩ
1 kΩ
500 Ω
500 Ω
0.1 V
0.15 V
0.15 V
0.3 V
VCCI/2
0V
VOLTAGE WAVEFORMS
PULSE DURATION
VCCB
Output
Control
(low-level
enabling)
VCCB/2
VCCB/2
0V
tPZL
VCCI
Input
VCCI/2
VCCI/2
0V
tPLH
Output
tPHL
VCCO/2
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
VOH
VCCO/2
VOL
tPLZ
VCCO
Output
Waveform 1
S1 at 2 × VCCO
(see Note B)
VCCO/2
VOL + VTP
VOL
tPZH
Output
Waveform 2
S1 at GND
(see Note B)
tPHZ
VCCO/2
VOH − VTP
VOH
0V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR10 MHz, ZO = 50 Ω, dv/dt ≥ 1 V/ns.
D. The outputs are measured one at a time, with one transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tPLH and tPHL are the same as tpd.
H. VCCI is the VCC associated with the input port.
I. VCCO is the VCC associated with the output port.
Figure 2. Load Circuit and Voltage Waveforms
9
PACKAGE OPTION ADDENDUM
www.ti.com
20-Feb-2010
PACKAGING INFORMATION
Orderable Device
Status (1)
74AVCB164245GRDR
ACTIVE
BGA MI
CROSTA
R JUNI
OR
GRD
54
1000
74AVCB164245GRE4
ACTIVE
TSSOP
DGG
48
74AVCB164245GRG4
ACTIVE
TSSOP
DGG
74AVCB164245VRE4
ACTIVE
TVSOP
74AVCB164245VRG4
ACTIVE
74AVCB164245ZQLR
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TBD
Lead/Ball Finish
MSL Peak Temp (3)
SNPB
Level-1-240C-UNLIM
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
48
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
DGV
48
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TVSOP
DGV
48
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
ACTIVE
BGA MI
CROSTA
R JUNI
OR
ZQL
56
1000 Green (RoHS &
no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
74AVCB164245ZRDR
ACTIVE
BGA MI
CROSTA
R JUNI
OR
ZRD
54
1000 Green (RoHS &
no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
SN74AVCB164245GR
ACTIVE
TSSOP
DGG
48
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74AVCB164245KR
NRND
BGA MI
CROSTA
R JUNI
OR
GQL
56
1000
SNPB
Level-1-240C-UNLIM
SN74AVCB164245VR
ACTIVE
TVSOP
DGV
48
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TBD
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
20-Feb-2010
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Aug-2009
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
74AVCB164245GRDR
BGA MI
CROSTA
R JUNI
OR
GRD
54
1000
330.0
16.4
5.8
8.3
1.55
8.0
16.0
Q1
74AVCB164245ZQLR
BGA MI
CROSTA
R JUNI
OR
ZQL
56
1000
330.0
16.4
4.8
7.3
1.45
8.0
16.0
Q1
74AVCB164245ZQLR
BGA MI
CROSTA
R JUNI
OR
ZQL
56
1000
330.0
16.4
4.8
7.3
1.5
8.0
16.0
Q1
74AVCB164245ZRDR
BGA MI
CROSTA
R JUNI
OR
ZRD
54
1000
330.0
16.4
5.8
8.3
1.55
8.0
16.0
Q1
SN74AVCB164245GR
TSSOP
DGG
48
2000
330.0
24.4
8.6
15.8
1.8
12.0
24.0
Q1
SN74AVCB164245KR
BGA MI
CROSTA
R JUNI
OR
GQL
56
1000
330.0
16.4
4.8
7.3
1.5
8.0
16.0
Q1
SN74AVCB164245KR
BGA MI
CROSTA
GQL
56
1000
330.0
16.4
4.8
7.3
1.45
8.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Aug-2009
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
10.2
1.6
12.0
16.0
R JUNI
OR
SN74AVCB164245VR
TVSOP
DGV
48
2000
330.0
16.4
7.1
Q1
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
74AVCB164245GRDR
BGA MICROSTAR
JUNIOR
GRD
54
1000
346.0
346.0
33.0
74AVCB164245ZQLR
BGA MICROSTAR
JUNIOR
ZQL
56
1000
346.0
346.0
33.0
74AVCB164245ZQLR
BGA MICROSTAR
JUNIOR
ZQL
56
1000
333.2
345.9
28.6
74AVCB164245ZRDR
BGA MICROSTAR
JUNIOR
ZRD
54
1000
346.0
346.0
33.0
SN74AVCB164245GR
TSSOP
DGG
48
2000
346.0
346.0
41.0
SN74AVCB164245KR
BGA MICROSTAR
JUNIOR
GQL
56
1000
333.2
345.9
28.6
SN74AVCB164245KR
BGA MICROSTAR
JUNIOR
GQL
56
1000
346.0
346.0
33.0
SN74AVCB164245VR
TVSOP
DGV
48
2000
346.0
346.0
33.0
Pack Materials-Page 2
MECHANICAL DATA
MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000
DGV (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
24 PINS SHOWN
0,40
0,23
0,13
24
13
0,07 M
0,16 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
0°–8°
1
0,75
0,50
12
A
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,08
14
16
20
24
38
48
56
A MAX
3,70
3,70
5,10
5,10
7,90
9,80
11,40
A MIN
3,50
3,50
4,90
4,90
7,70
9,60
11,20
DIM
4073251/E 08/00
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side.
Falls within JEDEC: 24/48 Pins – MO-153
14/16/20/56 Pins – MO-194
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS003D – JANUARY 1995 – REVISED JANUARY 1998
DGG (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
48 PINS SHOWN
0,27
0,17
0,50
48
0,08 M
25
6,20
6,00
8,30
7,90
0,15 NOM
Gage Plane
1
0,25
24
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
48
56
64
A MAX
12,60
14,10
17,10
A MIN
12,40
13,90
16,90
DIM
4040078 / F 12/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated