TI SN74HC163DR

SCLS298D − JANUARY 1996 − REVISED − OCTOBER 2003
D
D
D
D
D
D
D
D
D
D
Wide Operating Voltage Range of 2 V to 6 V
Outputs Can Drive Up To 10 LSTTL Loads
Low Power Consumption, 80-µA Max ICC
Typical tpd = 14 ns
±4-mA Output Drive at 5 V
Low Input Current of 1 µA Max
Internal Look-Ahead for Fast Counting
Carry Output for n-Bit Cascading
Synchronous Counting
Synchronously Programmable
SN54HC163 . . . J OR W PACKAGE
SN74HC163 . . . D, DB, N, NS, OR PW PACKAGE
(TOP VIEW)
CLR
CLK
A
B
C
D
ENP
GND
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC
RCO
QA
QB
QC
QD
ENT
LOAD
SN54HC163 . . . FK PACKAGE
(TOP VIEW)
description/ordering information
CLK
CLR
NC
VCC
RCO
These synchronous, presettable counters feature
an internal carry look-ahead for application in
high-speed counting designs. The ’HC163
devices are 4-bit binary counters. Synchronous
operation is provided by having all flip-flops
clocked simultaneously so that the outputs
change coincident with each other when
instructed by the count-enable (ENP, ENT) inputs
and internal gating. This mode of operation
eliminates the output counting spikes normally
associated with synchronous (ripple-clock)
counters. A buffered clock (CLK) input triggers the
four flip-flops on the rising (positive-going) edge of
the clock waveform.
4
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
QA
QB
NC
QC
QD
ENP
GND
NC
LOAD
ENT
A
B
NC
C
D
NC − No internal connection
ORDERING INFORMATION
PACKAGE†
TA
PDIP − N
SN74HC163N
Tube of 40
SN74HC163D
Reel of 2500
SN74HC163DR
Reel of 250
SN74HC163DT
SOP − NS
Reel of 2000
SN74HC163NSR
HC163
SSOP − DB
Reel of 2000
SN74HC163DBR
HC163
Tube of 90
SN74HC163PW
Reel of 2000
SN74HC163PWR
Reel of 250
SN74HC163PWT
CDIP − J
Tube of 25
SNJ54HC163J
SNJ54HC163J
CFP − W
Tube of 150
SNJ54HC163W
SNJ54HC163W
TSSOP − PW
−55°C
−55
C to 125
125°C
C
TOP-SIDE
MARKING
Tube of 25
SOIC − D
−40°C
−40
C to 85
85°C
C
ORDERABLE
PART NUMBER
SN74HC163N
HC163
HC163
LCCC − FK
Tube of 55
SNJ54HC163FK
SNJ54HC163FK
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are
available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2003, Texas Instruments Incorporated
! "#$ ! %#&'" ($)
(#"! " !%$""! %$ *$ $! $+! !#$!
!(( ,-) (#" %"$!!. ($! $"$!!'- "'#($
$!. '' %$$!)
%(#"! "%' /012
'' %$$! $ $!$(
#'$!! *$,!$ $() '' *$ %(#"!
%(#"
%"$!!. ($! $"$!!'- "'#($ $!. '' %$$!)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SCLS298D − JANUARY 1996 − REVISED − OCTOBER 2003
description/ordering information (continued)
These counters are fully programmable; that is, they can be preset to any number between 0 and 9 or 15. As
presetting is synchronous, setting up a low level at the load input disables the counter and causes the outputs
to agree with the setup data after the next clock pulse, regardless of the levels of the enable inputs.
The clear function for the ’HC163 devices is synchronous. A low level at the clear (CLR) input sets all four of
the flip-flop outputs low after the next low-to-high transition of CLK, regardless of the levels of the enable inputs.
This synchronous clear allows the count length to be modified easily by decoding the Q outputs for the maximum
count desired. The active-low output of the gate used for decoding is connected to CLR to synchronously clear
the counter to 0000 (LLLL).
The carry look-ahead circuitry provides for cascading counters for n-bit synchronous applications without
additional gating. ENP, ENT, and a ripple-carry output (RCO) are instrumental in accomplishing this function.
Both ENP and ENT must be high to count, and ENT is fed forward to enable RCO. Enabling RCO produces a
high-level pulse while the count is maximum (9 or 15 with QA high). This high-level overflow ripple-carry pulse
can be used to enable successive cascaded stages. Transitions at ENP or ENT are allowed, regardless of the
level of CLK.
These counters feature a fully independent clock circuit. Changes at control inputs (ENP, ENT, or LOAD) that
modify the operating mode have no effect on the contents of the counter until clocking occurs. The function of
the counter (whether enabled, disabled, loading, or counting) is dictated solely by the conditions meeting the
stable setup and hold times.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCLS298D − JANUARY 1996 − REVISED − OCTOBER 2003
logic diagram (positive logic)
LOAD
ENT
ENP
9
10
15
LD†
7
RCO
CK†
CLK
CLR
2
1
CK
LD
R
A
B
C
D
M1
G2
1, 2T/1C3
G4
3D
4R
3
M1
G2
1, 2T/1C3
G4
3D
4R
4
M1
G2
1, 2T/1C3
G4
3D
4R
5
M1
G2
1, 2T/1C3
G4
3D
4R
6
14
13
12
11
QA
QB
QC
QD
† For simplicity, routing of complementary signals LD and CK is not shown on this overall logic diagram. The uses of these signals are shown
on the logic diagram of the D/T flip-flops.
Pin numbers shown are for the D, DB, J, N, NS, PW, and W packages.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SCLS298D − JANUARY 1996 − REVISED − OCTOBER 2003
logic symbol, each D/T flip-flop
LD (Load)
M1
TE (Toggle Enable)
G2
CK (Clock)
1, 2T/1C3
G4
D (Inverted Data)
3D
R (Inverted Reset)
4R
Q (Output)
logic diagram, each D/T flip-flop (positive logic)
CK
LD
TE
LD†
TG
TG
LD†
Q
TG
TG
CK†
D
TG
CK†
R
† The origins of LD and CK are shown in the logic diagram of the overall device.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
CK†
TG
CK†
SCLS298D − JANUARY 1996 − REVISED − OCTOBER 2003
typical clear, preset, count, and inhibit sequence
The following sequence is illustrated below:
1. Clear outputs to zero (synchronous)
2. Preset to binary 12
3. Count to 13, 14, 15, 0, 1, and 2
4. Inhibit
CLR
LOAD
A
Data
Inputs
B
C
D
CLK
ENP
ENT
QA
Data
Outputs
QB
QC
QD
RCO
12
13
14
15
0
1
2
Count
Inhibit
Sync Preset
Clear
Async
Clear
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SCLS298D − JANUARY 1996 − REVISED − OCTOBER 2003
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25 mA
Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA
Package thermal impedance, θJA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73°C/W
DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82°C/W
N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67°C/W
NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64°C/W
PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
2. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions (see Note 3)
SN54HC163
VCC
VIH
Supply voltage
High-level input voltage
VCC = 2 V
VCC = 4.5 V
VCC = 6 V
VCC = 2 V
VIL
VI
VO
∆t/∆v‡
Low-level input voltage
MIN
NOM
MAX
2
5
6
MIN
NOM
MAX
2
5
6
1.5
1.5
3.15
3.15
4.2
4.2
VCC = 4.5 V
VCC = 6 V
Input voltage
0
Output voltage
0
Input transition rise/fall time
SN74HC163
VCC = 2 V
VCC = 4.5 V
VCC = 6 V
0.5
1.35
1.35
1.8
1.8
0
0
V
V
0.5
VCC
VCC
UNIT
VCC
VCC
1000
1000
500
500
400
400
V
V
V
ns
TA
Operating free-air temperature
−55
125
−40
85
°C
NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
‡ If this device is used in the threshold region (from VILmax = 0.5 V to VIHmin = 1.5 V), there is a potential to go into the wrong state from induced
grounding, causing double clocking. Operating with the inputs at tt = 1000 ns and VCC = 2 V does not damage the device; however, functionally,
the CLK inputs are not ensured while in the shift, count, or toggle operating modes.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCLS298D − JANUARY 1996 − REVISED − OCTOBER 2003
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
IOH = −20 µA
VOH
VI = VIH or VIL
IOH = −4 mA
IOH = −5.2 mA
IOL = 20 µA
VOL
VI = VIH or VIL
IOL = 4 mA
IOL = 5.2 mA
II
ICC
VI = VCC or 0
VI = VCC or 0,
IO = 0
VCC
MIN
TA = 25°C
TYP
MAX
MIN
MAX
SN74HC163
MIN
2V
1.9
1.998
1.9
1.9
4.5 V
4.4
4.499
4.4
4.4
6V
5.9
5.999
5.9
5.9
4.5 V
3.98
4.3
3.7
3.84
6V
5.48
5.8
5.2
MAX
UNIT
V
5.34
2V
0.002
0.1
0.1
0.1
4.5 V
0.001
0.1
0.1
0.1
6V
0.001
0.1
0.1
0.1
4.5 V
0.17
0.26
0.4
0.33
6V
0.15
0.26
0.4
0.33
6V
±0.1
±100
±1000
±1000
nA
8
160
80
µA
3
10
10
10
pF
6V
Ci
SN54HC163
2 V to 6 V
V
timing requirements over recommended operating free-air temperature range (unless otherwise
noted)
VCC
fclock
tw
Clock frequency
Pulse duration
CLK high or low
A, B, C, or D
LOAD low
tsu
Setup time before CLK↑
ENP, ENT
CLR low
CLR inactive
th
Hold time, all synchronous inputs after CLK
CLK↑
POST OFFICE BOX 655303
TA = 25°C
MIN
MAX
SN54HC163
MIN
MAX
SN74HC163
MIN
MAX
2V
6
4.2
5
4.5 V
31
21
25
6V
36
25
29
2V
80
120
100
4.5 V
16
24
20
6V
14
20
17
2V
150
225
190
4.5 V
30
45
38
6V
26
38
32
2V
135
205
170
4.5 V
27
41
34
6V
23
35
29
2V
170
255
215
4.5 V
34
51
43
6V
29
43
37
2V
160
240
200
4.5 V
32
48
40
6V
27
41
34
2V
160
240
200
4.5 V
32
48
40
6V
27
41
34
2V
0
0
0
4.5 V
0
0
0
6V
0
0
0
• DALLAS, TEXAS 75265
UNIT
MHz
ns
ns
ns
7
SCLS298D − JANUARY 1996 − REVISED − OCTOBER 2003
switching characteristics over recommended operating free-air temperature range, CL = 50 pF
(unless otherwise noted) (see Figure 1)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
fmax
RCO
CLK
tpd
Any Q
ENT
tt
RCO
Any
VCC
MIN
TA = 25°C
TYP
MAX
SN54HC163
MIN
MAX
SN74HC163
MIN
2V
6
14
4.2
5
4.5 V
31
40
21
25
6V
36
44
25
29
MAX
UNIT
MHz
2V
83
215
325
270
4.5 V
24
43
65
54
6V
20
37
55
46
2V
80
205
310
255
4.5 V
25
41
62
51
6V
21
35
53
43
2V
62
195
295
245
4.5 V
17
39
59
49
6V
14
33
50
42
2V
38
75
110
95
4.5 V
8
15
22
19
6V
6
13
19
16
ns
ns
operating characteristics, TA = 25°C
PARAMETER
Cpd
8
TEST CONDITIONS
Power dissipation capacitance
No load
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TYP
60
UNIT
pF
SCLS298D − JANUARY 1996 − REVISED − OCTOBER 2003
PARAMETER MEASUREMENT INFORMATION
From Output
Under Test
VCC
High-Level
Pulse
Test
Point
50%
50%
0V
tw
CL = 50 pF
(see Note A)
VCC
Low-Level
Pulse
50%
50%
0V
LOAD CIRCUIT
VOLTAGE WAVEFORMS
PULSE DURATIONS
Input
VCC
50%
50%
0V
tPLH
Reference
Input
VCC
50%
In-Phase
Output
50%
10%
0V
tsu
Data
Input 50%
10%
90%
tr
tPHL
VCC
50%
10% 0 V
90%
90%
tr
th
90%
tPHL
Out-of-Phase
Output
90%
VOLTAGE WAVEFORMS
SETUP AND HOLD AND INPUT RISE AND FALL TIMES
tPLH
50%
10%
tf
tf
VOH
50%
10%
VOL
tf
50%
10%
90%
VOH
VOL
tr
VOLTAGE WAVEFORMS
PROPAGATION DELAY AND OUTPUT TRANSITION TIMES
NOTES: A. CL includes probe and test-fixture capacitance.
B. Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators having the following
characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr = 6 ns, tf = 6 ns.
C. For clock inputs, fmax is measured when the input duty cycle is 50%.
D. The outputs are measured one at a time with one input transition per measurement.
E. tPLH and tPHL are the same as tpd.
Figure 1. Load Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SCLS298D − JANUARY 1996 − REVISED − OCTOBER 2003
APPLICATION INFORMATION
n-bit synchronous counters
This application demonstrates how the look-ahead carry circuit can be used to implement a high-speed n-bit
counter. The ’HC163 devices count in binary. Virtually any count mode (modulo-N, N1-to-N2, N1-to-maximum)
can be used with this fast look-ahead circuit.
The application circuit shown in Figure 2 is not valid for clock frequencies above 18 MHz (at 25°C and
4.5-V VCC). The reason for this is that there is a glitch that is produced on the second stage’s RCO and every
succeeding stage’s RCO. This glitch is common to all HC vendors that Texas Instruments has evaluated, in
addition to the bipolar equivalents (LS, ALS, AS).
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCLS298D − JANUARY 1996 − REVISED − OCTOBER 2003
APPLICATION INFORMATION
LSB
CTR
CT=0
M1
3CT=MAX
G3
CLR
Clear (L)
LOAD
ENT
Count (H)/
Disable (L)
ENP
CLK
RCO
G4
C5/2,3,4+
Load (L)
A
1,5D [1]
QA
Count (H)/
Disable (L)
B
[2]
QB
C
[3]
QC
Clock
D
[4]
QD
CTR
CT=0
M1
3CT=MAX
G3
CLR
LOAD
ENT
ENP
CLK
RCO
G4
C5/2,3,4+
A
1,5D [1]
QA
B
[2]
QB
C
[3]
QC
D
[4]
QD
CTR
CT=0
M1
3CT=MAX
G3
CLR
LOAD
ENT
ENP
CLK
RCO
G4
C5/2,3,4+
A
1,5D [1]
QA
B
[2]
QB
C
[3]
QC
D
[4]
QD
CTR
CT=0
M1
3CT=MAX
G3
CLR
LOAD
ENT
ENP
CLK
RCO
G4
C5/2,3,4+
A
1,5D [1]
QA
B
[2]
QB
C
[3]
QC
D
[4]
QD
To More-Significant Stages
Figure 2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SCLS298D − JANUARY 1996 − REVISED − OCTOBER 2003
APPLICATION INFORMATION
n-bit synchronous counters (continued)
The glitch on RCO is caused because the propagation delay of the rising edge of QA of the second stage is
shorter than the propagation delay of the falling edge of ENT. RCO is the product of ENT, QA, QB, QC, and QD
(ENT × QA × QB × QC × QD). The resulting glitch is about 7−12 ns in duration. Figure 3 shows the condition in
which the glitch occurs. For simplicity, only two stages are being considered, but the results can be applied to
other stages. QB, QC, and QD of the first and second stage are at logic one, and QA of both stages are at logic
zero (1110 1110) after the first clock pulse. On the rising edge of the second clock pulse, QA and RCO of the
first stage go high. On the rising edge of the third clock pulse, QA and RCO of the first stage return to a low level,
and QA of the second stage goes to a high level. At this time, the glitch on RCO of the second stage appears
because of the race condition inside the chip.
1
2
3
4
5
CLK
ENT1
QB1, QC1, QD1
QA1
RCO1, ENT2
QB2, QC2, QD2
QA2
RCO2
Glitch (7−12 ns)
Figure 3
The glitch causes a problem in the next stage (stage three) if the glitch is still present when the next rising clock
edge appears (clock pulse 4). To ensure that this does not happen, the clock frequency must be less than the
inverse of the sum of the clock-to-RCO propagation delay and the glitch duration (tg). In other words,
fmax = 1/(tpd CLK-to-RCO + tg). For example, at 25°C at 4.5-V VCC, the clock-to-RCO propagation delay is
43 ns and the maximum duration of the glitch is 12 ns. Therefore, the maximum clock frequency that the
cascaded counters can use is 18 MHz. The following tables contain the fclock, tw, and fmax specifications for
applications that use more than two ’HC163 devices cascaded together.
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCLS298D − JANUARY 1996 − REVISED − OCTOBER 2003
APPLICATION INFORMATION
n-bit synchronous counters (continued)
timing requirements over recommended operating free-air temperature range (unless otherwise
noted)
VCC
fclock
tw
Clock frequency
Pulse duration, CLK high or low
TA = 25°C
MIN
MAX
SN54HC163
MIN
MAX
SN74HC163
MIN
MAX
2V
3.6
2.5
2.9
4.5 V
18
12
14
6V
21
14
17
2V
140
200
170
4.5 V
28
40
36
6V
24
36
30
UNIT
MHz
ns
switching characteristics over recommended operating free-air temperature range, CL = 50 pF
(unless otherwise noted) (see Note 4)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
fmax
VCC
TA = 25°C
MIN
MAX
SN54HC163
MIN
MAX
SN74HC163
MIN
2V
3.6
2.5
2.9
4.5 V
18
12
14
6V
21
14
17
MAX
UNIT
MHz
NOTE 4: These limits apply only to applications that use more than two ’HC163 devices cascaded together.
If the ’HC163 devices are used as a single unit, or only two cascaded together, then the maximum clock
frequency that the devices can use is not limited because of the glitch. In these situations, the devices can be
operated at the maximum specifications.
A glitch can appear on RCO of a single ’HC163 device, depending on the relationship of ENT to CLK. Any
application that uses RCO to drive any input, except an ENT of another cascaded ’HC163 device, must take
this into consideration.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
PACKAGE OPTION ADDENDUM
www.ti.com
28-Feb-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
Lead/Ball Finish
MSL Peak Temp (3)
86076012A
ACTIVE
LCCC
FK
20
1
None
Call TI
Level-NC-NC-NC
8607601EA
ACTIVE
CDIP
J
16
1
None
Call TI
Level-NC-NC-NC
8607601FA
ACTIVE
CFP
W
16
1
None
Call TI
Level-NC-NC-NC
JM38510/66304BEA
ACTIVE
CDIP
J
16
1
None
Call TI
Level-NC-NC-NC
SN54HC163J
ACTIVE
CDIP
J
16
1
None
Call TI
Level-NC-NC-NC
SN74HC163D
ACTIVE
SOIC
D
16
40
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
SN74HC163DBR
ACTIVE
SSOP
DB
16
2000
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
SN74HC163DR
ACTIVE
SOIC
D
16
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
SN74HC163DT
ACTIVE
SOIC
D
16
250
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
SN74HC163N
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
Level-NC-NC-NC
SN74HC163NSR
ACTIVE
SO
NS
16
2000
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
SN74HC163PW
ACTIVE
TSSOP
PW
16
90
Pb-Free
(RoHS)
CU NIPDAU
Level-1-250C-UNLIM
SN74HC163PWR
ACTIVE
TSSOP
PW
16
2000
Pb-Free
(RoHS)
CU NIPDAU
Level-1-250C-UNLIM
SN74HC163PWT
ACTIVE
TSSOP
PW
16
250
Pb-Free
(RoHS)
CU NIPDAU
Level-1-250C-UNLIM
SNJ54HC163FK
ACTIVE
LCCC
FK
20
1
None
Call TI
Level-NC-NC-NC
SNJ54HC163J
ACTIVE
CDIP
J
16
1
None
Call TI
Level-NC-NC-NC
SNJ54HC163W
ACTIVE
CFP
W
16
1
None
Call TI
Level-NC-NC-NC
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional
product content details.
None: Not yet available Lead (Pb-Free).
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens,
including bromine (Br) or antimony (Sb) above 0.1% of total product weight.
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
28-Feb-2005
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
MLCC006B – OCTOBER 1996
FK (S-CQCC-N**)
LEADLESS CERAMIC CHIP CARRIER
28 TERMINAL SHOWN
18
17
16
15
14
13
NO. OF
TERMINALS
**
12
19
11
20
10
A
B
MIN
MAX
MIN
MAX
20
0.342
(8,69)
0.358
(9,09)
0.307
(7,80)
0.358
(9,09)
28
0.442
(11,23)
0.458
(11,63)
0.406
(10,31)
0.458
(11,63)
21
9
22
8
44
0.640
(16,26)
0.660
(16,76)
0.495
(12,58)
0.560
(14,22)
23
7
52
0.739
(18,78)
0.761
(19,32)
0.495
(12,58)
0.560
(14,22)
24
6
68
0.938
(23,83)
0.962
(24,43)
0.850
(21,6)
0.858
(21,8)
84
1.141
(28,99)
1.165
(29,59)
1.047
(26,6)
1.063
(27,0)
B SQ
A SQ
25
5
26
27
28
1
2
3
4
0.080 (2,03)
0.064 (1,63)
0.020 (0,51)
0.010 (0,25)
0.020 (0,51)
0.010 (0,25)
0.055 (1,40)
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.045 (1,14)
0.035 (0,89)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
4040140 / D 10/96
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a metal lid.
The terminals are gold plated.
Falls within JEDEC MS-004
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
0,15 M
15
0,25
0,09
8,20
7,40
5,60
5,00
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
2,00 MAX
0,10
0,05 MIN
PINS **
14
16
20
24
28
30
38
A MAX
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
12,30
DIM
4040065 /E 12/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-150
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated