[ /Title (CD74 HC154 , CD74 HCT15 4) /Subject (High Speed CMOS Logic 4-to-16 Line Decod er/Dem CD74HC154, CD74HCT154 Data sheet acquired from Harris Semiconductor SCHS152 High Speed CMOS Logic 4-to-16 Line Decoder/Demultiplexer September 1997 Features Description • Two Enable Inputs to Facilitate Demultiplexing and Cascading Functions • Fanout (Over Temperature Range) - Standard Outputs . . . . . . . . . . . . . . . 10 LSTTL Loads - Bus Driver Outputs . . . . . . . . . . . . . 15 LSTTL Loads The Harris CD74HC154 and CD74HCT154 are 4-to-16 line decoders/demultiplexers with two enable inputs, E1 and E2. A High on either enable input forces the output into the High state. The demultiplexing function is performed by using the four input lines, A0 to A3, to select the output lines Y0 to Y15, and using one enable as the data input while holding the other enable low. • Wide Operating Temperature Range . . . -55oC to 125oC • Balanced Propagation Delay and Transition Times Ordering Information • Significant Power Reduction Compared to LSTTL Logic ICs PART NUMBER • HC Types - 2V to 6V Operation - High Noise Immunity: NIL = 30%, NIH = 30%of VCC at VCC = 5V • HCT Types - 4.5V to 5.5V Operation - Direct LSTTL Input Logic Compatibility, VIL= 0.8V (Max), VIH = 2V (Min) - CMOS Input Compatibility, Il ≤ 1µA at VOL, VOH TEMP. RANGE (oC) PKG. NO. PACKAGE CD74HC154E -55 to 125 24 Ld PDIP E24.6 CD74HCT154E -55 to 125 24 Ld PDIP E24.6 CD74HC154EN -55 to 125 24 Ld PDIP E24.3 CD74HC154EN -55 to 125 24 Ld PDIP E24.3 CD74HC154M -55 to 125 24 Ld SOIC M24.3 CD74HCT154M -55 to 125 24 Ld SOIC M24.3 NOTES: 1. When ordering, use the entire part number. Add the suffix 96 to obtain the variant in the tape and reel. 2. Wafer or d ie for this part number is available which meets all electrical specifications. Please contact your local sales office or Harris customer service for ordering information. Pinout CD74HC154, CD74HCT154 (PDIP, SOIC) TOP VIEW Y0 1 24 VCC Y1 2 23 A0 Y2 3 22 A1 Y3 4 21 A2 Y4 5 20 A3 Y5 6 19 E2 Y6 7 18 E1 Y7 8 17 Y15 Y8 9 16 Y14 Y9 10 15 Y13 Y10 11 14 Y12 GND 12 13 Y11 CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright © Harris Corporation 1997 1 File Number 1657.1 CD74HC154, CD74HCT154 Functional Diagram 1 2 3 4 5 6 7 A0 23 8 A1 22 9 A2 A3 21 10 20 11 13 14 15 E1 E2 18 16 19 17 Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 Y10 Y11 Y12 Y13 Y14 Y15 GND = 12 VCC = 24 TRUTH TABLE INPUTS OUTPUTS E1 E2 A3 A2 A1 A0 Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 Y10 Y11 Y12 Y13 Y14 Y15 L L L L L L L H H H H H H H H H H H H H H H L L L L L H H L H H H H H H H H H H H H H H L L L L H L H H L H H H H H H H H H H H H H L L L L H H H H H L H H H H H H H H H H H H L L L H L L H H H H L H H H H H H H H H H H L L L H L H H H H H H L H H H H H H H H H H L L L H H L H H H H H H L H H H H H H H H H L L L H H H H H H H H H H L H H H H H H H H L L H L L L H H H H H H H H L H H H H H H H L L L H L H H H H H H H H H H L H H H H H H L L H L H L H H H H H H H H H H L H H H H H L L H L H H H H H H H H H H H H H L H H H H L L H H L L H H H H H H H H H H H H L H H H L L H H L H H H H H H H H H H H H H H L H H L L H H H L H H H H H H H H H H H H H H L H L L H H H H H H H H H H H H H H H H H H H L L H X X X X H H H H H H H H H H H H H H H H H L X X X X H H H H H H H H H H H H H H H H H H X X X X H H H H H H H H H H H H H H H H NOTE: H = High Voltage Level, L = Low Voltage Level, X = Don’t Care 2 CD74HC154, CD74HCT154 Absolute Maximum Ratings Thermal Information DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V DC Input Diode Current, IIK For VI < -0.5V or VI > VCC + 0.5V . . . . . . . . . . . . . . . . . . . . . .±20mA DC Output Diode Current, IOK For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±20mA DC Output Source or Sink Current per Output Pin, IO For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±25mA DC VCC or Ground Current, ICC or IGND . . . . . . . . . . . . . . . . . .±50mA Thermal Resistance (Typical, Note 3) θJA (oC/W) PDIP Package (.300) . . . . . . . . . . . . . . . . . . . . . . . . 75 PDIP Package (.600) . . . . . . . . . . . . . . . . . . . . . . . . 60 SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range (TA) . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Supply Voltage Range, VCC HC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 6V HCT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V DC Input or Output Voltage, VI, VO . . . . . . . . . . . . . . . . . 0V to VCC Input Rise and Fall Time 2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000ns (Max) 4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500ns (Max) 6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400ns (Max) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 3. θJA is measured with the component mounted on an evaluation PC board in free air. DC Electrical Specifications TEST CONDITIONS PARAMETER 25oC -40oC TO 85oC -55oC TO 125oC SYMBOL VI (V) IO (mA) VCC (V) VIH - - 2 1.5 - - 1.5 4.5 3.15 - - 3.15 - 3.15 - V 6 4.2 - - 4.2 - 4.2 - V MIN TYP MAX MIN MAX MIN MAX UNITS - 1.5 - V HC TYPES High Level Input Voltage Low Level Input Voltage High Level Output Voltage CMOS Loads VIL VOH - VIH or VIL High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads Input Leakage Current Quiescent Device Current - 2 - - 0.5 - 0.5 - 0.5 V 4.5 - - 1.35 - 1.35 - 1.35 V 6 - - 1.8 - 1.8 - 1.8 V -0.02 2 1.9 - - 1.9 - 1.9 - V -0.02 4.5 4.4 - - 4.4 - 4.4 - V -0.02 6 5.9 - - 5.9 - 5.9 - V - - - - - - - - - V -4 4.5 3.98 - - 3.84 - 3.7 - V -5.2 6 5.48 - - 5.34 - 5.2 - V 0.02 2 - - 0.1 - 0.1 - 0.1 V 0.02 4.5 - - 0.1 - 0.1 - 0.1 V 0.02 6 - - 0.1 - 0.1 - 0.1 V - - - - - - - - - V 4 4.5 - - 0.26 - 0.33 - 0.4 V 5.2 6 - - 0.26 - 0.33 - 0.4 V II VCC or GND - 6 - - ±0.1 - ±1 - ±1 µA ICC VCC or GND 0 6 - - 8 - 80 - 160 µA 3 CD74HC154, CD74HCT154 DC Electrical Specifications (Continued) TEST CONDITIONS SYMBOL VI (V) IO (mA) High Level Input Voltage VIH - - Low Level Input Voltage VIL - High Level Output Voltage CMOS Loads VOH VIH or VIL PARAMETER 25oC VCC (V) -40oC TO 85oC -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS 4.5 to 5.5 2 - - 2 - 2 - V - 4.5 to 5.5 - - 0.8 - 0.8 - 0.8 V -0.02 4.5 4.4 - - 4.4 - 4.4 - V -4 4.5 3.98 - - 3.84 - 3.7 - V 0.02 4.5 - - 0.1 - 0.1 - 0.1 V 4 4.5 - - 0.26 - 0.33 - 0.4 V ±0.1 - ±1 - ±1 µA HCT TYPES High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads Input Leakage Current Quiescent Device Current Additional Quiescent Device Current Per Input Pin: 1 Unit Load II VCC and GND 0 5.5 - ICC VCC or GND 0 5.5 - - 8 - 80 - 160 µA ∆ICC VCC -2.1 - 4.5 to 5.5 - 100 360 - 450 - 490 µA NOTE: For dual-supply systems theoretical worst case (VI = 2.4V, VCC = 5.5V) specification is 1.8mA. HCT Input Loading Table INPUT UNIT LOADS A0 - A3 1.4 E1, E2 1.3 NOTE: Unit Load is ∆ICC limit specified in DC Electrical Table, e.g., 360µA max at 25oC. Switching Specifications Input tr, tf = 6ns PARAMETER TEST CONDITIONS -40oC TO 85oC 25oC -55oC TO 125oC VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS 2 - - 175 - 220 - 265 ns 4.5 - - 35 - 44 - 53 ns CL =15pF 5 - 14 - - - - - ns CL = 50pF 6 - - 30 - 37 - 45 ns tPLH, tPHL CL = 50pF 2 - - 175 - 220 - 265 ns 4.5 - - 35 - 44 - 53 ns CL =15pF 5 - 14 - - - - - ns CL = 50pF 6 - - 30 - 37 - 45 ns SYMBOL HC TYPES Propagation Delay (Figure 1) tPLH, tPHL CL = 50pF Address to Output E1 to Output 4 CD74HC154, CD74HCT154 Switching Specifications Input tr, tf = 6ns PARAMETER TEST CONDITIONS -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS 2 - - 175 - 220 - 265 ns 4.5 - - 35 - 44 - 53 ns CL =15pF 5 - 14 - - - - - ns CL = 50pF 6 - - 30 - 37 - 45 ns tTLH, tTHL CL = 50pF 2 - - 75 - 95 - 110 ns 4.5 - - 15 - 19 - 22 ns 6 - - 13 - 16 - 19 ns tPLH, tPHL CL = 50pF Output Transition Time (Figure 1) -40oC TO 85oC 25oC VCC (V) SYMBOL E2 to Output (Continued) Input Capacitance CIN - - - - 10 - 10 - 10 pF Power Dissipation Capacitance (Notes 4, 5) CPD - 5 - 88 - - - - - pF CL = 50pF 4.5 - - 35 - 44 - 53 ns CL =15pF 5 - 14 - - - - ns 4.5 - - 34 - 43 - 51 ns 5 - 14 - - - - - ns 4.5 - 34 - 43 - 51 ns 5 - 14 - - - - - ns 4.5 - - 15 - 19 - 22 ns - - 10 - 10 - 10 pF 84 - - - - - pF HCT TYPES Propagation Delay (Figure 2) tPLH, tPHL Address to Output E1 to Output tPLH, tPHL CL = 50pF CL =15pF E2 to Output tPLH, tPHL CL = 50pF CL =15pF Output Transition Time tTLH, tTHL CL = 50pF Input Capacitance CIN - - Power Dissipation Capacitance (Notes 4, 5) CPD - 5 NOTES: 4. CPD is used to determine the dynamic power consumption, per gate. 5. PD = VCC2 fi (CPD + CL) where fi = input frequency, CL = output load capacitance, VCC = supply voltage. Test Circuits and Waveforms tr = 6ns tf = 6ns 90% 50% 10% INPUT GND tTLH GND tTHL 90% 50% 10% INVERTING OUTPUT 3V 2.7V 1.3V 0.3V INPUT tTHL tPHL tf = 6ns tr = 6ns VCC tTLH 90% 1.3V 10% INVERTING OUTPUT tPHL tPLH FIGURE 1. HC AND HCU TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC tPLH FIGURE 2. HCT TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC 5 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated