ADS1218 ADS 121 8 SBAS187 – SEPTEMBER 2001 8-Channel, 24-Bit ANALOG-TO-DIGITAL CONVERTER with FLASH Memory FEATURES DESCRIPTION ● 24 BITS NO MISSING CODES ● 0.0015% INL ● 22 BITS EFFECTIVE RESOLUTION (PGA = 1), 19 BITS (PGA = 128) ● 4K BYTES OF FLASH MEMORY PROGRAMMABLE FROM 2.7V TO 5.25V ● PGA FROM 1 TO 128 ● SINGLE CYCLE SETTLING MODE ● PROGRAMMABLE DATA OUTPUT RATES UP TO 1kHz ● PRECISION ON-CHIP 1.25V/2.5V REFERENCE: ACCURACY: 0.2% DRIFT: 5ppm/°C ● EXTERNAL DIFFERENTIAL REFERENCE OF 0.1V TO 2.5V ● ON-CHIP CALIBRATION ● PIN COMPATIBLE WITH ADS1216 ● SPI™ COMPATIBLE ● 2.7V TO 5.25V ● < 1mW POWER CONSUMPTION The ADS1218 is a precision, wide dynamic range, delta-sigma, Analog-toDigital (A/D) converter with 24-bit resolution and FLASH memory operating from 2.7V to 5.25V supplies. The delta-sigma, A/D converter provides up to 24 bits of no missing code performance and effective resolution of 22 bits. The eight input channels are multiplexed. Internal buffering can be selected to provide a very high input impedance for direct connection to transducers or low-level voltage signals. Burn out current sources are provided that allow for the detection of an open or shorted sensor. An 8-bit Digital-to-Analog (D/ A) converter provides an offset correction with a range of 50% of the FSR (Full-Scale Range). The PGA (Programmable Gain Amplifier) provides selectable gains of 1 to 128 with an effective resolution of 19 bits at a gain of 128. The A/D conversion is accomplished with a second-order delta-sigma modulator and programmable sinc filter. The reference input is differential and can be used for ratiometric conversion. The on-board current DACs (Digital-to-Analog Converters) operate independently with the maximum current set by an external resistor. The serial interface is SPI compatible. Eight bits of digital I/O are also provided that can be used for input or output. The ADS1218 is designed for high-resolution measurement applications in smart transmitters, industrial process control, weight scales, chromatography, and portable instrumentation. AGND APPLICATIONS ● ● ● ● ● ● ● INDUSTRIAL PROCESS CONTROL LIQUID /GAS CHROMATOGRAPHY BLOOD ANALYSIS SMART TRANSMITTERS PORTABLE INSTRUMENTATION WEIGHT SCALES PRESSURE TRANSDUCERS RDAC AVDD IDAC2 8-Bit IDAC IDAC1 8-Bit IDAC AVDD 2µA VREFOUT VRCAP VREF+ VREF– XIN XOUT Clock Generator 1.25V or 2.5V Reference Offset DAC AIN0 A = 1:128 AIN1 Registers IN+ AIN2 AIN3 MUX IN– AIN4 BUF + PGA AIN5 2nd-Order Modulator Programmable Digital Filter Controller RAM 4K Bytes FLASH WREN AIN6 SPI is a registered trademark of Motorola. AIN7 AINCOM POL 2µA Serial Interface Digital I/O Interface AGND DVDD DGND BUFEN SCLK DIN DOUT CS D0 ... D7 PDWN DSYNC RESET DRDY Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright © 2001, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com ABSOLUTE MAXIMUM RATINGS(1) ELECTROSTATIC DISCHARGE SENSITIVITY AVDD to AGND ...................................................................... –0.3V to +6V DVDD to DGND ...................................................................... –0.3V to +6V Input Current ............................................................... 100mA, Momentary Input Current ................................................................. 10mA, Continuous AIN ................................................................... GND –0.5V to AVDD + 0.5V AVDD to DVDD ........................................................................... –6V to +6V AGND to DGND ................................................................. –0.3V to +0.3V Digital Input Voltage to GND .................................... –0.3V to DVDD + 0.3V Digital Output Voltage to GND ................................. –0.3V to DVDD + 0.3V Maximum Junction Temperature ................................................... +150°C Operating Temperature Range ......................................... –40°C to +85°C Storage Temperature Range .......................................... –60°C to +100°C Lead Temperature (soldering, 10s) .............................................. +300°C This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. Electrostatic discharge can cause damage ranging from performance degradation to complete device failure. Texas Instruments recommends that all integrated circuits be handled and stored using appropriate ESD protection methods. NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliability. PACKAGE/ORDERING INFORMATION SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER TRANSPORT MEDIA, QUANTITY ADS1218Y/250 ADS1218Y/2K Tape and Reel, 250 Tape and Reel, 2000 PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR ADS1218Y TQFP-48 PFB –40°C to +85°C ADS1218Y " " " " " NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., / 2K indicates 2000 devices per reel). Ordering 2000 pieces of “ADS1218Y/2K” will get a single 2000-piece Tape and Reel. ELECTRICAL CHARACTERISTICS: AVDD = 5V All specifications TMIN to TMAX, AVDD = +5V, DVDD = +2.7V to 5.25V, fMOD = 19.2kHz, fOSC = 2.4576MHz, PGA = 1, Buffer ON, RDAC = 150kΩ, fDATA = 10Hz, VREF ≡ (REF IN+) – (REF IN–) = +2.5V, unless otherwise specified. ADS1218 PARAMETER ANALOG INPUT (AIN0 – AIN7, AINCOM) Analog Input Range Full-Scale Input Voltage Range Differential Input Impedance Input Current Bandwidth Fast Settling Filter Sinc2 Filter Sinc3 Filter Programmable Gain Amplifier Input Capacitance Input Leakage Current Burnout Current Sources CONDITIONS MIN Buffer OFF Buffer ON (In+) – (In–), See Block Diagram Buffer OFF Buffer ON AGND – 0.1 AGND + 0.05 –3dB –3dB –3dB User Selectable Gain Ranges SYSTEM PERFORMANCE Resolution No Missing Codes Integral Non-Linearity Offset Error(1) Offset Drift(1) Gain Error Gain Error Drift(1) Common-Mode Rejection Normal-Mode Rejection Output Noise Power-Supply Rejection 2 MAX UNITS AVDD + 0.1 AVDD – 1.5 ±VREF /PGA 5/PGA 0.5 V V V MΩ nA 0.469 • fDATA 0.318 • fDATA 0.262 • fDATA Hz Hz Hz 1 Modulator OFF, T = 25°C OFFSET DAC Offset DAC Range Offset DAC Monotonicity Offset DAC Gain Error Offset DAC Gain Error Drift TYP 128 9 5 2 pF pA µA ±VREF /(2 • PGA) V Bits % ppm/°C 8 ±10 1 24 sinc3 End Point Fit Before Calibration 24 ±0.0015 7.5 0.02 0.005 0.5 After Calibration fCM = fCM = fCM = fSIG = fSIG = at DC 60Hz, fDATA = 10Hz 50Hz, fDATA = 50Hz 60Hz, fDATA = 60Hz 50Hz, fDATA = 50Hz 60Hz, fDATA = 60Hz at DC, dB = –20 log(∆VOUT /∆VDD)(2) 100 80 130 120 120 100 100 See Typical Characteristics 95 Bits Bits % of FS ppm of FS ppm of FS/°C % ppm/ °C dB dB dB dB dB dB dB ADS1218 SBAS187 ELECTRICAL CHARACTERISTICS: AVDD = 5V (Cont.) All specifications TMIN to TMAX, AVDD = +5V, DVDD = +2.7V to 5.25V, fMOD = 19.2kHz, fOSC = 2.4576MHz, PGA = 1, Buffer ON, RDAC = 150kΩ, fDATA =10Hz, VREF ≡ (REF IN+) – (REF IN–) = +2.5V, unless otherwise specified. ADS1218 PARAMETER VOLTAGE REFERENCE INPUT Reference Input Range VREF Common-Mode Rejection Common-Mode Rejection Bias Current(3) ON-CHIP VOLTAGE REFERENCE Output Voltage Short-Circuit Current Source Short-Circuit Current Sink Short-Circuit Duration Drift Noise Output Impedance Startup Time IDAC Full-Scale Output Current Maximum Short-Circuit Current Duration Monotonicity Compliance Voltage Output Impedance PSRR Absolute Error Absolute Drift Mismatch Error Mismatch Drift POWER-SUPPLY REQUIREMENTS Power-Supply Voltage Analog Current (IADC + IVREF + IDAC) ADC Current (IADC) VREF Current (IVREF) IDAC Current (IDAC) Digital Current Power Dissipation TEMPERATURE RANGE Operating Storage CONDITIONS MIN REF IN+, REF IN– VREF ≡ (REF IN+) – (REF IN–) at DC fVREFCM = 60Hz, fDATA = 60Hz VREF = 2.5V 0 0.1 REF HI = 1 at 25°C REF HI = 0 2.495 Sink or Source BW = 0.1Hz to 100Hz Sourcing 100µA RDAC = 150kΩ, Range = 1 RDAC = 150kΩ, Range = 2 RDAC = 150kΩ, Range = 3 RDAC = 15kΩ, Range = 3 RDAC = 10kΩ RDAC = 0Ω RDAC = 150kΩ 2.5 120 120 1.3 2.50 1.25 8 50 Indefinite 5 10 3 50 MAX UNITS AVDD 2.6 V V dB dB µA 2.505 V V mA µA ppm/°C µVp-p Ω µs 0.5 1 2 20 Indefinite 8 0 mA mA mA mA 10 Minutes AVDD – 1 Bits V see Typical Characteristics 400 5 75 0.25 15 VOUT = AVDD /2 Individual IDAC Individual IDAC Between IDACs, Same Range and Code Between IDACs, Same Range and Code AVDD PDWN = 0, or SLEEP PGA = 1, Buffer OFF PGA = 128, Buffer OFF PGA = 1, Buffer ON PGA = 128, Buffer ON TYP 4.75 ppm/V % ppm/°C % ppm/°C 5.25 V nA µA µA µA µA µA µA Excludes Load Current 1 175 500 250 900 250 480 Normal Mode, DVDD = 5V SLEEP Mode, DVDD = 5V Read Data Continuous Mode, DVDD = 5V PDWN= LOW 180 150 230 1 275 µA µA µA nA PGA = 1, Buffer OFF, REFEN = 0, IDACS OFF, DVDD = 5V 1.8 2.8 mW +85 +100 °C °C –40 –60 275 750 350 1375 375 675 NOTES: (1) Calibration can minimize these errors. (2) ∆ VOUT is change in digital result. (3) 12pF switched capacitor at fSAMP clock frequency. ADS1218 SBAS187 3 ELECTRICAL CHARACTERISTICS: AVDD = 3V All specifications TMIN to TMAX, AVDD = +3V, DVDD = +2.7V to 5.25V, fMOD = 19.2kHz, fOSC = 2.4576MHz, PGA = 1, Buffer ON, RDAC = 75kΩ, fDATA=10Hz, VREF ≡ (REF IN+) – (REF IN–) = +1.25V unless otherwise specified. ADS1218 PARAMETER ANALOG INPUT (AIN0 – AIN7, AINCOM) Analog Input Range Full-Scale Input Voltage Range Input Impedance Input Current Bandwidth Fast Settling Filter Sinc2 Filter Sinc3 Filter Programmable Gain Amplifier Input Capacitance Input Leakage Current Burnout Current Sources CONDITIONS MIN Buffer OFF Buffer ON (In+) – (In–) See Block Diagram Buffer OFF Buffer ON AGND – 0.1 AGND + 0.05 –3dB –3dB –3dB User Selectable Gain Ranges SYSTEM PERFORMANCE Resolution No Missing Codes Integral Non-Linearity Offset Error(1) Offset Drift(1) Gain Error Gain Error Drift(1) Common-Mode Rejection Normal-Mode Rejection Output Noise Power-Supply Rejection VOLTAGE REFERENCE INPUT Reference Input Range VREF Common-Mode Rejection Common-Mode Rejection Bias Current(3) ON-CHIP VOLTAGE REFERENCE Output Voltage Short-Circuit Current Source Short-Circuit Current Sink Short-Circuit Duration Drift Noise Output Impedance Startup Time IDAC Full-Scale Output Current Maximum Short-Circuit Current Duration Monotonicity Compliance Voltage Output Impedance PSRR Absolute Error Absolute Drift Mismatch Error Mismatch Drift 4 MAX UNITS AVDD + 0.1 AVDD – 1.5 ±VREF /PGA 5/ PGA 0.5 V V V MΩ nA 0.469 • fDATA 0.318 • fDATA 0.262 • fDATA Hz Hz Hz 1 Modulator OFF, T = 25°C OFFSET DAC Offset DAC Range Offset DAC Monotonicity Offset DAC Gain Error Offset DAC Gain Error Drift TYP 128 9 5 2 pF pA µA ±VREF /(2 • PGA) V Bits % ppm/°C 8 ±10 2 24 24 ±0.0015 End Point Fit Before Calibration 15 0.04 0.010 1.0 After Calibration fCM = fCM = fCM = fSIG = fSIG = at DC 60Hz, fDATA = 50Hz, fDATA = 60Hz, fDATA = 50Hz, fDATA = 60Hz, fDATA = 100 10Hz 50Hz 60Hz 50Hz 60Hz at DC, dB = –20 log(∆VOUT /∆VDD)(2) 75 REF IN+, REF IN– VREF ≡ (REF IN+) – (REF IN–) at DC fVREFCM = 60Hz, fDATA = 60Hz VREF = 1.25V 0 0.1 REF HI = 0 at 25°C 1.245 BW = 0.1Hz to 100Hz Sourcing 100µA = 75kΩ, Range = 75kΩ, Range = 75kΩ, Range = 15kΩ, Range RDAC = 10kΩ RDAC = 0Ω RDAC = 75kΩ = = = = 1 2 3 3 VOUT = AVDD /2 Individual IDAC Individual IDAC Between IDACs, Same Range and Code Between IDACs, Same Range and Code dB AVDD 1.25 V V dB dB µA 1.255 V mA µA 120 120 0.65 Sink or Source RDAC RDAC RDAC RDAC 130 120 120 100 100 see Typical Characteristics 90 1.25 3 50 Indefinite 5 10 3 50 ppm/°C µVp-p Ω µs 0.5 1 2 20 Indefinite mA mA mA mA 10 8 0 AVDD – 1 see Typical Characteristics 600 5 75 0.25 15 Bits Bits % of FS ppm of FS ppm of FS/°C % ppm/°C dB dB dB dB dB dB Minute Bits V ppm/V % ppm/°C % ppm/°C ADS1218 SBAS187 ELECTRICAL CHARACTERISTICS: AVDD = 3V (Cont.) All specifications TMIN to TMAX, AVDD = +3V, DVDD = +2.7V to 5.25V, fMOD = 19.2kHz, fOSC = 2.4576MHz, PGA = 1, Buffer ON, RDAC = 75kΩ, fDATA=10Hz, VREF ≡ (REF IN+) – (REF IN–) = +1.25V unless otherwise specified. ADS1218 PARAMETER POWER-SUPPLY REQUIREMENTS Power-Supply Voltage Analog Current (IADC + IVREF + IDAC) ADC Current (IADC) VREF Current (IVREF) IDAC Current (IDAC) Digital Current Power Dissipation CONDITIONS MIN AVDD PDWN = 0, or SLEEP PGA = 1, Buffer OFF PGA = 128, Buffer OFF PGA = 1, Buffer ON PGA = 128, Buffer ON 2.7 1 160 450 230 850 250 480 90 75 113 1 0.8 Excludes Load Current Normal Mode, DVDD = 3V SLEEP Mode, DVDD = 3V Read Data Continuous Mode, DVDD = 3V PDWN = 0 PGA = 1, Buffer OFF, REFEN = 0, IDACS OFF, DVDD = 3V TEMPERATURE RANGE Operating Storage TYP –40 –60 MAX UNITS 3.3 1.4 V nA µA µA µA µA µA µA µA µA µA nA mW +85 +100 °C °C 250 700 325 1325 375 675 200 NOTES: (1) Calibration can minimize these errors. (2) ∆ VOUT is change in digital result. (3) 12pF switched capacitor at fSAMP clock frequency. DIGITAL CHARACTERISTICS: TMIN to TMAX, DVDD = 2.7V to 5.25V PARAMETER Digital Input/Output Logic Family Logic Level: VIH VIL VOH VOL Input Leakage: IIH IIL Master Clock Rate: fOSC(1) Master Clock Period: tOSC(1) CONDITIONS MIN TYP MAX UNITS DVDD 0.2 • DVDD V V V V µA µA MHz ns CMOS IOH = 1mA IOL = 1mA VI = DVDD VI = 0 1/fOSC 0.8 • DVDD DGND DVDD – 0.4 DGND DGND + 0.4 10 –10 1 200 5 1000 NOTE: (1) For FLASH E/W operations, the SPEED bit in the SETUP register must be set appropriately and the device operating frequency must be: 2.3MHz < FOSC < 4.13MHz. FLASH CHARACTERISTICS: TMIN to TMAX, DVDD = 2.7V to 5.25V, unless otherwise specified. PARAMETER Operating Current Page Write Page Read Endurance Data Retention DVDD for Erase/Write ADS1218 SBAS187 CONDITIONS MIN DVDD = 5V, During WR2F Command DVDD = 3V, During WR2F Command DVDD = 5V, During RF2R Command DVDD = 3V, During RF2R Command at 25°C TYP MAX UNITS 5.25 mA mA mA mA E/W Cycles Years V 6.5 3.75 4.0 1.2 100,000 100 2.7 5 DOUT DIN SCLK CS DRDY DVDD DGND DSYNC POL PDWN XOUT XIN PIN CONFIGURATION (TQFP-48) 36 35 34 33 32 31 30 29 28 27 26 25 D0 37 24 RESET D1 38 23 BUFEN D2 39 22 DGND D3 40 21 DGND D4 41 20 DGND D5 42 19 DGND ADS1218 D6 43 18 WREN D7 44 17 RDAC 5 6 7 8 9 10 11 12 AGND 4 AINCOM 3 AIN7 2 AIN4 1 AIN6 13 AVDD AIN5 VREF– 48 AIN3 14 VRCAP AIN2 VREF+ 47 AIN1 15 IDAC1 AIN0 VREFOUT 46 AGND 16 IDAC2 AVDD AGND 45 PIN DESCRIPTIONS 6 PIN NUMBER NAME DESCRIPTION Analog Power Supply 24 RESET Active LOW, resets the entire chip. AGND Analog Ground 25 XIN AIN0 Analog Input 0 26 XOUT Clock Output, used with crystal or resonator. 4 AIN1 Analog Input 1 27 PDWN 5 AIN2 Analog Input 2 6 AIN3 Analog Input 3 Active LOW. Power Down. The power down function shuts down the analog and digital circuits. 7 AIN4 Analog Input 4 8 AIN5 Analog Input 5 9 AIN6 Analog Input 6 10 AIN7 Analog Input 7 PIN NUMBER NAME DESCRIPTION 1 AVDD 2 3 11 AINCOM Analog Input Common 12 AGND Analog Ground 13 AVDD Analog Power Supply 14 VRCAP VREF Bypass CAP 15 IDAC1 Current DAC1 Output 16 IDAC2 Current DAC2 Output 17 RDAC Current DAC Resistor 18 WREN 19-22 DGND Active High, FLASH Write Enable Digital Ground 23 BUFEN Buffer Enable Clock Input 28 POL 29 DSYNC Serial Clock Polarity Active LOW, Synchronization Control 30 DGND Digital Ground 31 DVDD Digital Power Supply 32 DRDY Active LOW, Data Ready 33 CS 34 SCLK 35 DIN 36 DOUT 37-44 D0-D7 Active LOW, Chip Select Serial Clock, Schmitt Trigger Serial Data Input, Schmitt Trigger Serial Data Output Digital I/O 0-7 45 AGND 46 VREFOUT Analog Ground 47 VREF+ Positive Differential Reference Input 48 VREF– Negative Differential Reference Input Voltage Reference Output ADS1218 SBAS187 TIMING SPECIFICATIONS CS t3 t1 t2 t10 SCLK (POL = 0) SCLK (POL = 1) t4 DIN MSB t2 t6 t5 t11 LSB (Command or Command and Data) DOUT t7 t8 t9 MSB(1) LSB(1) NOTE: (1) Bit Order = 0. ADS1218 Resets On Falling Edge SCLK Reset Waveform t13 t13 SCLK t12 t14 t16 t15 RESET, DSYNC, PDWN DDR Update Timing t17 DRDY TIMING SPECIFICATION TABLES SPEC DESCRIPTION t1 SCLK Period t2 t3 t4 t5 t6 SCLK Pulse Width, HIGH and LOW CS LOW to first SCLK Edge; Setup Time DIN Valid to SCLK Edge; Setup Time Valid DIN to SCLK Edge; Hold Time Delay between last SCLK edge for DIN and first SCLK edge for DOUT: RDATA, RDATAC, RREG, WREG, RRAM, WRAM CSREG, CSRAMX, CSRAM CHKARAM, CHKARAMX SCLK Edge to Valid New DOUT SCLK Edge to DOUT, Hold Time Last SCLK Edge to DOUT Tri-State NOTE: DOUT goes tri-state immediately when CS goes HIGH. CS LOW time after final SCLK edge Final SCLK edge of one op code until first edge SCLK of next command: RREG, WREG, RRAM, WRAM, CSRAMX, CSARAMX, CSRAM, CSARAM, CSREG, SLEEP, RDATA, RDATAC, STOPC DSYNC, RESET CSFL CREG, CRAM RF2R CREGA WR2F MIN MAX 4 3 t7 (1) t8 (1) t9 t10 t11 t12 t13 t14 t15 t16 t17 SELFGCAL, SELFOCAL, SYSOCAL, SYSGCAL SELFCAL RESET (Command, SCLK, or Pin) SCLK Reset, First HIGH Pulse SCLK Reset, LOW Pulse SCLK Reset, Second HIGH Pulse SCLK Reset, Third HIGH Pulse Pulse Width DOR Data Not Valid 200 0 50 50 50 200 1100 50 0 6 10 UNITS tOSC Periods DRDY Periods ns ns ns ns tOSC Periods tOSC Periods tOSC Periods ns ns tOSC Periods 0 ns 4 16 33,000 220 1090 1600 76,850 (SPEED = 0) 101,050 (SPEED = 1) 7 14 16 300 5 550 1050 4 4 tOSC Periods tOSC Periods tOSC Periods tOSC Periods tOSC Periods tOSC Periods tOSC Periods tOSC Periods DRDY Periods DRDY Periods tOSC Periods tOSC Periods tOSC Periods tOSC Periods tOSC Periods tOSC Periods tOSC Periods 4 500 750 1250 NOTE: (1) Load = 20pF 10kΩ to DGND. ADS1218 SBAS187 7 TYPICAL CHARACTERISTICS AVDD = +5V, DVDD = +5V, fOSC = 2.4576MHz, PGA = 1, RDAC = 150kΩ, fDATA = 10Hz, VREF ≡ (REF IN+) – (REF IN–) = +2.5V, unless otherwise specified. EFFECTIVE NUMBER OF BITS vs DECIMATION RATIO EFFECTIVE NUMBER OF BITS vs DECIMATION RATIO 22 22 PGA1 PGA2 PGA4 PGA1 PGA2 PGA8 20 20 19 19 18 PGA16 PGA32 PGA64 PGA128 17 16 14 18 17 16 PGA64 PGA128 Sinc3 Filter, Buffer ON 13 12 12 0 500 1000 1500 Decimation Ratio = 0 2000 500 fMOD 1000 Decimation Ratio = fDATA 1500 fMOD 2000 fDATA EFFECTIVE NUMBER OF BITS vs DECIMATION RATIO EFFECTIVE NUMBER OF BITS vs DECIMATION RATIO 22 22 PGA1 21 PGA2 PGA4 PGA1 PGA2 PGA8 20 20 19 19 18 17 PGA16 PGA64 PGA32 PGA4 PGA128 16 18 17 16 15 15 14 Sinc3 Filter, 13 PGA32 14 VREF = 1.25V, Buffer OFF 1000 Decimation Ratio = 1500 fMOD 0 2000 PGA128 Sinc3 Filter, VREF = 1.25V, Buffer ON 12 500 PGA64 PGA16 13 12 0 PGA8 21 ENOB (rms) ENOB (rms) PGA32 PGA16 14 Sinc3 Filter 13 500 1000 Decimation Ratio = fDATA 1500 fMOD 2000 fDATA FAST SETTLING FILTER EFFECTIVE NUMBER OF BITS vs DECIMATION RATIO EFFECTIVE NUMBER OF BITS vs DECIMATION RATIO 22 22 PGA1 21 PGA2 PGA4 PGA8 21 20 20 19 19 ENOB (rms) ENOB (rms) PGA8 15 15 18 17 PGA32 16 PGA64 PGA128 PGA16 18 17 16 15 15 14 Sinc2 Filter 13 14 Fast Settling Filter 13 12 12 0 500 1000 Decimation Ratio = 8 PGA4 21 ENOB (rms) ENOB (rms) 21 1500 fMOD fDATA 2000 0 500 1000 Decimation Ratio = 1500 2000 fMOD fDATA ADS1218 SBAS187 TYPICAL CHARACTERISTICS (Cont.) AVDD = +5V, DVDD = +5V, fOSC = 2.4576MHz, PGA = 1, RDAC = 150kΩ, fDATA = 10Hz, VREF ≡ (REF IN+) – (REF IN–) = +2.5V, unless otherwise specified. CMRR vs FREQUENCY NOISE vs INPUT SIGNAL 0.8 0.6 0.5 CMRR (dB) Noise (rms, ppm of FS) 0.7 0.4 0.3 0.2 0.1 0 –2.5 –1.5 –0.5 0.5 1.5 130 120 110 100 90 80 70 60 50 40 30 20 10 0 2.5 1 10 100 VIN (V) 120 110 100 90 80 70 60 50 40 30 20 10 0 100k 50 PGA16 PGA1 0 Offset (ppm of FS) PSRR (dB) 10k OFFSET vs TEMPERATURE PSRR vs FREQUENCY –50 PGA64 –100 PGA128 –150 –200 1 10 100 1k 10k –50 100k –30 –10 10 30 50 70 90 Temperature (°C) Frequency of Power Supply (Hz) GAIN vs TEMPERATURE INTEGRAL NON-LINEARITY vs INPUT SIGNAL 1.00010 10 8 1.00006 –40°C 6 1.00002 INL (ppm of FS) Gain (Normalized) 1k Frequency of CM Signal (Hz) 0.99998 0.99994 4 +85°C 2 0 –2 –4 +25°C –6 0.99990 –8 0.99986 –50 –30 –10 10 30 Temperature (°C) ADS1218 SBAS187 50 70 90 –10 –2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5 2 2.5 VIN (V) 9 TYPICAL CHARACTERISTICS (Cont.) AVDD = +5V, DVDD = +5V, fOSC = 2.4576MHz, PGA = 1, RDAC = 150kΩ, fDATA = 10Hz, VREF ≡ (REF IN+) – (REF IN–) = +2.5V, unless otherwise specified. CURRENT vs TEMPERATURE ADC CURRENT vs PGA 250 900 IDIGITAL Buffer = OFF 700 IANALOG 600 150 IADC (µA) Current (µA) 200 AVDD = 5V, Buffer = ON 800 IANALOG IDIGITAL 100 500 AVDD = 3V, Buffer = ON 400 Buffer = OFF 300 200 50 100 0 0 –50 –30 –10 10 30 50 70 90 0 1 2 Temperature (°C) 8 16 32 64 128 PGA Setting DIGITAL CURRENT HISTOGRAM OF OUTPUT DATA 4500 SPEED = 0 350 SLEEP fOSC = 4.91MHz 300 Normal fOSC = 4.91MHz 4000 Number of Occurrences 400 Current (µA) 4 Normal fOSC = 2.45MHz 250 200 150 100 Power Down 50 SLEEP fOSC = 2.45MHz 3500 3000 2500 2000 1500 1000 500 0 0 3.0 4.0 –2 5.0 –1.5 –1 –0.5 0 0.5 1 1.5 2 ppm of FS VDD (V) OFFSET DAC - OFFSET vs TEMPERATURE VREFOUT vs LOAD CURRENT 200 2.55 170 Offset (ppm of FSR) VREFOUT (V) 140 2.50 110 80 50 20 –10 –40 –70 2.45 –0.5 –100 0 0.5 1.0 1.5 VREFOUT Current Load (mA) 10 2.0 2.5 –50 –30 –10 10 30 50 70 90 Temperature (°C) ADS1218 SBAS187 TYPICAL CHARACTERISTICS (Cont.) AVDD = +5V, DVDD = +5V, fOSC = 2.4576MHz, PGA = 1, RDAC = 150kΩ, fDATA = 10Hz, VREF ≡ (REF IN+) – (REF IN–) = +2.5V, unless otherwise specified. IDAC ROUT vs VOUT OFFSET DAC - GAIN vs TEMPERATURE 1.00020 1.000 1.00016 +85°C 1.000 1.00008 IOUT (Normalized) Normalized Gain 1.00012 1.00004 1.00000 0.99996 0.99992 0.99988 +25°C 0.999 0.999 0.99984 –40°C 0.99980 0.99976 0.998 –50 –30 –10 10 30 50 70 90 0 1 2 Temperature (°C) 3 4 5 VDD – VOUT (V) IDAC MATCHING vs TEMPERATURE IDAC NORMALIZED vs TEMPERATURE 3000 1.01 2000 1000 IDAC Match (ppm) IOUT (Normalized) 1.005 1 0.995 0 –1000 –2000 –3000 –4000 0.99 –5000 –6000 0.985 –30 –10 10 30 50 70 –50 90 –30 –10 10 30 50 70 Temperature (°C) Temperature (°C) IDAC DIFFERENTIAL NON-LINEARITY RANGE = 1, RDAC = 150kΩ, VREF = 2.5V IDAC INTEGRAL NON-LINEARITY RANGE = 1, RDAC = 150kΩ, VREF = 2.5V 0.5 0.5 0.4 0.4 0.3 0.3 0.2 0.2 0.1 INL (LSB) DNL (LSB) –50 0 –0.1 0.1 0 –0.1 –0.2 –0.2 –0.3 –0.3 –0.4 –0.4 –0.5 90 –0.5 0 32 64 96 128 160 IDAC Code ADS1218 SBAS187 192 224 255 0 32 64 96 128 160 192 224 255 IDAC Code 11 OVERVIEW BURNOUT CURRENT SOURCES INPUT MULTIPLEXER The input multiplexer provides for any combination of differential inputs to be selected on any of the input channels, as shown in Figure 1. For example, if channel 1 is selected as the positive differential input channel, any other channel can be selected as the negative differential input channel. With this method, it is possible to have up to eight fully differential input channels. In addition, current sources are supplied that will source or sink current to detect open or short circuits on the input pins. INPUT BUFFER The input impedance of the ADS1218 without the buffer is 5MΩ/PGA. With the buffer enabled, the input voltage range is reduced and the analog power-supply current is higher. The buffer is controlled by ANDing the state of the BUFEN pin with the state of the BUFFER bit in the ACR register. IDAC1 AND IDAC2 AIN0 AIN1 When the Burnout bit is set in the ACR configuration register, two current sources are enabled. The current source on the positive input channel sources approximately 2µA of current. The current source on the negative input channel sinks approximately 2µA. This allows for the detection of an open circuit (full-scale reading) or short circuit (0V differential reading) on the selected input differential pair. AVDD Burnout Current Source On AIN2 AIN3 AIN4 The ADS1218 has two 8-bit current output DACs that can be controlled independently. The output current is set with RDAC, the range select bits in the ACR register, and the 8-bit digital value in the IDAC register. The output current = VREF /(8 • RDAC)(2RANGE–1)(DAC CODE). With VREFOUT = 2.5V and RDAC = 150kΩ to AGND the full-scale output can be selected to be 0.5, 1, or 2mA. The compliance voltage range is 0 to within 1V of AVDD. When the internal voltage reference of the ADS1218 is used, it is the reference for the IDAC. An external reference may be used for the IDACs by disabling the internal reference and tying the external reference input to the VREFOUT pin. AIN5 PGA Burnout Current Source On AIN6 AGND IDAC1 AIN7 AINCOM FIGURE 1. Input Multiplexer Configuration. TEMPERATURE SENSOR An on-chip diode provides temperature sensing capability. When the configuration register for the input MUX is set to all 1s, the diode is connected to the input of the A/D converter. All other channels are open. The anode of the diode is connected to the positive input of the A/D converter, and the cathode of the diode is connected to negative input of the A/D converter. The output of IDAC1 is connected to the anode to bias the diode and the cathode of the diode is also connected to ground to complete the circuit. In this mode, the output of IDAC1 is also connected to the output pin, so some current may flow into an external load from IDAC1, rather than the diode. 12 The Programmable Gain Amplifier (PGA) can be set to gains of 1, 2, 4, 8, 16, 32, 64, or 128. Using the PGA can actually improve the effective resolution of the A/D converter. For instance, with a PGA of 1 on a 5V full-scale range, the A/D converter can resolve to 1µV. With a PGA of 128, on a 40mV full-scale range, the A/D converter can resolve to 75nV. With a PGA of 1 on a 5V full-scale range, it would require a 26-bit A/D converter to resolve 75nV. PGA OFFSET DAC The input to the PGA can be shifted by half the full-scale input range of the PGA by using the ODAC register. The ODAC (Offset DAC) register is an 8-bit value; the MSB is the sign and the seven LSBs provide the magnitude of the offset. Using the ODAC register does not reduce the performance of the A/D converter. MODULATOR The modulator is a single-loop second-order system. The modulator runs at a clock speed (fMOD) that is derived from the external clock (fOSC). The frequency division is determined by the SPEED bit in the SETUP register. SPEED BIT fMOD 0 fOSC / 128 1 fOSC / 256 ADS1218 SBAS187 The offset and gain errors in the ADS1218, or the complete system, can be reduced with calibration. Internal calibration of the ADS1218 is called self calibration. This is handled with three commands. One command does both offset and gain calibration. There is also a gain calibration command and an offset calibration command. Each calibration process takes seven tDATA periods to complete. Therefore, it takes 14 tDATA periods to complete both an offset and gain calibration. For system calibration, the appropriate signal must be applied to the inputs. The system offset command requires a “zero” differential input signal. It then computes an offset that will nullify offset in the system. The system gain command requires a positive “full-scale” differential input signal. It then computes a value to nullify gain errors in the system. Each of these calibrations will take seven tDATA periods to complete. settling filter for the next two conversions, the first of which should be discarded. It will then use the sinc2 followed by the sinc3 filter to improve noise performance. This combines the low-noise advantage of the sinc3 filter with the quick response of the fast settling time filter. The frequency response of each filter is shown in Figure 3. SINC3 FILTER RESPONSE (–3dB = 0.262 • fDATA = 15.76Hz) 0 –20 –40 Gain (dB) CALIBRATION –60 –80 Calibration should be performed after power on, a change in temperature, a change in decimation ratio, or a change in the PGA. Calibration will remove the offset in the ODAC register. Therefore, changes to the ODAC register must be done after calibration. –100 –120 0 30 60 90 120 150 180 210 240 270 300 Frequency (Hz) At the completion of calibration, the DRDY signal will go LOW to indicate that calibration is complete and valid data is available. SINC2 FILTER RESPONSE (–3dB = 0.318 • fDATA = 19.11Hz) 0 DIGITAL FILTER –20 –40 Gain (dB) The Digital Filter can use either the fast settling, sinc2, or sinc3 filter, as shown in Figure 2. In addition, the Auto mode changes the sinc filter after the input channel or PGA is changed. When switching to a new channel, it will use the fast –60 –80 Adjustable Digital Filter –100 –120 Sinc3 0 30 60 90 120 150 180 210 240 270 300 Frequency (Hz) Modulator Output Sinc2 Data Out FAST SETTLING FILTER RESPONSE (–3dB = 0.469 • fDATA = 28.125Hz) 0 Fast Settling –20 FILTER SETTLING TIME FILTER Sinc3 Sinc2 Fast 3(1) 2(1) 1(1) Gain (dB) –40 SETTLING TIME (Conversion Cycles) –60 –80 NOTE: (1) With Synchronized Channel Changes. –100 AUTO MODE FILTER SELECTION –120 CONVERSION CYCLE 0 1 2 3 4+ Discard Fast Sinc2 Sinc3 FIGURE 2. Filter Step Responses. ADS1218 SBAS187 30 60 90 120 150 180 210 240 270 300 Frequency (Hz) NOTE: fDATA = 60Hz. FIGURE 3. Filter Frequency Responses. 13 VOLTAGE REFERENCE DIGITAL I/O INTERFACE The voltage reference used for the ADS1218 can either be internal or external. The power-up configuration for the voltage reference is 2.5V internal. The selection for the voltage reference is made through the status configuration register. The ADS1218 has eight pins dedicated for digital I/O. The default power-up condition for the digital I/O pins are as inputs. All of the digital I/O pins are individually configurable as inputs or outputs. They are configured through the DIR control register. The DIR register defines whether the pin is an input or output, and the DIO register defines the state of the digital output. When the digital I/O are configured as inputs, DIO is used to read the state of the pin. The internal voltage reference is selectable as either 1.25V or 2.5V (AVDD = 5V only). The VREFOUT pin should have a 0.1µF capacitor to AGND. The external voltage reference is differential and is represented by the voltage difference between the pins: +VREF and –VREF. The absolute voltage on either pin (+VREF and –VREF) can range from AGND to AVDD, however, the differential voltage must not exceed 2.5V. The differential voltage reference provides easy means of performing ratiometric measurement. VRCAP PIN This pin provides a bypass cap for noise filtering on internal VREF circuitry only. The recommended capacitor is a 0.001µF ceramic cap. If an external VREF is used, this pin can be left unconnected. SERIAL INTERFACE The serial interface is standard four-wire SPI compatible (DIN, DOUT, SCLK, and CS). The ADS1218 also offers the flexibility to select the polarity of the serial clock through the POL pin. The serial interface can be clocked up to fOSC/4. If CS goes HIGH, the serial interface is reset. When CS goes LOW, a new command is expected. The serial interface operates independently of DRDY. DRDY is used to indicate availability of data in the DOR. In order to ensure the validity of the data being read, DOR timing requirements must be met. DSYNC OPERATION CLOCK GENERATOR The clock source for the ADS1218 can be provided from a crystal, ceramic resonator, oscillator, or external clock. When the clock source is a crystal or ceramic resonator, external capacitors must be provided to ensure start-up and a stable clock frequency. This is shown in Figure 4 and Table I. C1 Crystal or Ceramic Resonator C2 XIN XOUT DSYNC is used to provide for synchronization of the A/D conversion with an external event. Synchronization can be achieved either through the DSYNC pin or the DSYNC command. When the DSYNC pin is used, the filter counter is reset on the falling edge of DSYNC. The modulator is held in reset until DSYNC is taken HIGH. Synchronization occurs on the next rising edge of the system clock after DSYNC is taken HIGH. When the DSYNC command is sent, the filter counter is reset after the last SCLK on the DSYNC command. The modulator is held in RESET until the next edge of SCLK is detected. Synchronization occurs on the next rising edge of the system clock after the first SCLK after the DSYNC command. POWER-UP—SUPPLY VOLTAGE RAMP RATE FIGURE 4. Crystal or Ceramic Resonator Connection. CLOCK SOURCE FREQUENCY C1 C2 PART NUMBER Crystal 2.4576 0-20pF 0-20pF ECS, ECSD 2.45 - 32 Crystal 4.9152 0-20pF 0-20pF ECS, ECSL 4.91 Crystal 4.9152 0-20pF 0-20pF ECS, ECSD 4.91 Crystal 4.9152 0-20pF 0-20pF CTS, MP 042 4M9182 TABLE I. Typical Clock Sources. 14 The power-on reset circuitry was designed to accommodate digital supply ramp rates as slow as 1V/10ms. To ensure proper operation, the power supply should ramp monotonically. The POR issues the RESET command as described below. RESET There are three methods of reset. The RESET pin, the RESET command, and the SCLK Reset pattern. They all perform the same function. After a reset, the FLASH data values from Page 0 are loaded into RAM, subsequently data values from Bank 0 of RAM are loaded into the configuration registers. ADS1218 SBAS187 MEMORY Three types of memory are used on the ADS1218: registers, RAM, and FLASH. 16 registers directly control the various functions (PGA, DAC value, Decimation Ratio, etc.) and can be directly read or written to. Collectively, the registers contain all the information needed to configure the part, such as data format, mux settings, calibration settings, decimation ratio, etc. Additional registers, such as conversion data, are accessed through dedicated instructions. basis. Also, the RAM can be directly read or written through the serial interface on power-up. The banks allow separate storage of settings for each input. Configuration Register Bank 16 bytes SETUP MUX ACR IDAC1 IDAC2 ODAC DIO DIR DEC0 M/DEC1 OCR0 OCR1 OCR2 FSR0 FSR1 FSR2 The on-chip FLASH can be used to store non-volatile data. The FLASH data is separate from the configuration registers and therefore can be used for any purpose, in addition to device configuration. The FLASH page data is read and written in 128 byte blocks through the RAM banks, i.e. all RAM banks map to a single page of FLASH, as shown in Figure 5. RAM 128 Bytes FLASH 4k Bytes Bank 0 16 bytes Bank 2 16 bytes REGISTER BANK TOPOLOGY The operation of the device is set up through individual registers. The set of the 16 registers required to configure the device is referred to as a Register Bank, as shown in Figure 5. RAM Reads and Writes to Registers and RAM occur on a byte basis. However, copies between registers and RAM occurs on a bank basis. The RAM is independent of the Registers, i.e.: the RAM can be used as general-purpose RAM. Page 0 128 bytes Bank 7 16 bytes The ADS1218 supports any combination of eight analog inputs. With this flexibility, the device could easily support eight unique configurations—one per input channel. In order to facilitate this type of usage, eight separate register banks are available. Therefore, each configuration could be written once and recalled as needed without having to serially retransmit all the configuration data. Checksum commands are also included, which can be used to verify the integrity of RAM. The RAM provides eight “banks”, with a bank consisting of 16 bytes. The total size of the RAM is 128 bytes. Copies between the registers and RAM are performed on a bank ADDRESS REGISTER BIT 7 BIT 6 Page 31 128 bytes FIGURE 5. Memory Organization. BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 00H SETUP ID ID ID SPEED REF EN REF HI BUF EN BIT ORDER 01H MUX PSEL3 PSEL2 PSEL1 PSEL0 NSEL3 NSEL2 NSEL1 NSEL0 02H ACR BOCS IDAC2R1 IDAC2R0 IDAC1R1 IDAC1R0 PGA2 PGA1 PGA0 03H IDAC1 IDAC1_7 IDAC1_6 IDAC1_5 IDAC1_4 IDAC1_3 IDAC1_2 IDAC1_1 IDAC1_0 04H IDAC2 IDAC2_7 IDAC2_6 IDAC2_5 IDAC2_4 IDAC2_3 IDAC2_2 IDAC2_1 IDAC2_0 05H ODAC SIGN OSET_6 OSET_5 OSET_4 OSET_3 OSET_2 OSET_1 OSET_0 06H DIO DIO_7 DIO_6 DIO_5 DIO_4 DIO_3 DIO_2 DIO_1 DIO_0 07H DIR DIR_7 DIR_6 DIR_5 DIR_4 DIR_3 DIR_2 DIR_1 DIR_0 08H DEC0 DEC07 DEC06 DEC05 DEC04 DEC03 DEC02 DEC01 DEC00 09H M/DEC1 DRDY U/B SMODE1 SMODE0 WREN DEC10 DEC09 DEC08 0AH OCR0 OCR07 OCR06 OCR05 OCR04 OCR03 OCR02 OCR01 OCR00 0BH OCR1 OCR15 OCR14 OCR13 OCR12 OCR11 OCR10 OCR09 OCR08 0CH OCR2 OCR23 OCR22 OCR21 OCR20 OCR19 OCR18 OCR17 OCR16 0DH FSR0 FSR07 FSR06 FSR05 FSR04 FSR03 FSR02 FSR01 FSR00 0EH FSR1 FSR15 FSR14 FSR13 FSR12 FSR11 FSR10 FSR09 FSR08 0FH FSR2 FSR23 FSR22 FSR21 FSR20 FSR19 FSR18 FSR17 FSR16 TABLE II. Registers. ADS1218 SBAS187 15 The RAM address space is linear, therefore accessing RAM is done using an auto-incrementing pointer. Access to RAM in the entire memory map can be done consecutively without having to address each bank individually. For example, if you were currently accessing bank 0 at offset 0xF (the last location of bank 0), the next access would be bank 1 and offset 0x0. Any access after bank 7 and offset 0xF will wrap around to bank 0 and Offset 0x0. Although the Register Bank memory is linear, the concept of addressing the device can also be thought of in terms of bank and offset addressing. Looking at linear and bank addressing syntax, we have the following comparison: in the linear memory map, the address 0x14 is equivalent to bank 1 and offset 0x4. Simply stated, the most significant four bits represent the bank, and the least significant four bits represent the offset. The offset is equivalent to the register address for that bank of memory. FLASH Reads and Writes to FLASH occur on a Page basis. Therefore, the entire contents of RAM is used for both Read and Write operations. The FLASH is independent of the Registers, i.e., the FLASH can be used as generalpurpose FLASH. Upon power-up or reset, the contents of FLASH Page 0 are loaded into RAM subsequently the contents of RAM Bank 0 are loaded into the configuration register. Therefore, the user can customize the power-up configuration for the device. Care should be taken to ensure that data for FLASH Page 0 is written correctly, in order to prevent unexpected operation upon power-up. 16 The ADS1218 supports any combination of eight analog inputs and the FLASH memory supports up to 32 unique Page configurations. With this flexibility, the device could support 32 unique configurations for each of the eight analog input channels. For instance, the on-chip temperature sensor could be used to monitor temperature then different calibration coefficients could be recalled for each of the eight analog input channels based on the change in temperature. This would enable the user to recall calibration coefficients for every 4°C change in temperature over the industrial temperature range which could be used to correct for drift errors. Checksum commands are also included, which can be used to verify the integrity of FLASH. The following two commands can be used to manipulate the FLASH. First, the contents of FLASH can be written to with the WR2F (write RAM to FLASH) command. This command first erases the designated FLASH page and then writes the entire content of RAM (all banks) into the designated FLASH page. Second, the contents of FLASH can be read with the RF2R (read FLASH to RAM) command. This command reads the designated FLASH page into the entire contents of RAM (all banks). In order to ensure maximum endurance and data retention, the SPEED bit in the SETUP register must be set for the appropriate fOSC frequency. Writing to or erasing FLASH can be disabled either through the WREN pin or the WREN register bit. If the WREN pin is LOW OR the WREN bit is cleared, then the WR2F command has no effect. This protects the integrity of the FLASH data from being inadvertently corrupted. Accessing the FLASH data either through read, write, or erase may effect the accuracy of the conversion result. Therefore, the conversion result should be discarded when accesses to FLASH are done. ADS1218 SBAS187 DETAILED REGISTER DEFINITIONS SETUP (Address 00H) Setup Register Reset Value = iii01110 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 ID ID ID SPEED REF EN REF HI ACR (Address 02H) Analog Control Register Reset Value = 00H bit 7 bit 1 bit 0 BUF EN BIT ORDER bit 7-5 Factory Programmed Bits bit 4 SPEED: FLASH Access Clock Speed 0 : 2.30MHz > fOSC > 3.12MHz (default) 1 : 3.12MHz > fOSC > 4.13MHz bit 3 REF EN: Internal Voltage Reference Enable 0 = Internal Voltage Reference Disabled 1 = Internal Voltage Reference Enabled (default) bit 2 REF HI: Internal Reference Voltage Select 0 = Internal Reference Voltage = 1.25V 1 = Internal Reference Voltage = 2.5V (default) bit 1 BUF EN: Buffer Enable 0 = Buffer Disabled 1 = Buffer Enabled (default) bit 0 BIT ORDER: Set Order Bits are Transmitted 0 = Most Significant Bit Transmitted First (default) 1 = Least Significant Bit Transmitted First Data is always shifted into the part most significant bit first. Data is always shifted out of the part most significant byte first. This configuration bit only controls the bit order within the byte of data that is shifted out. MUX (Address 01H) Multiplexer Control Register Reset Value = 01H bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 PSEL3 PSEL2 PSEL1 PSEL0 NSEL3 NSEL2 NSEL1 NSEL0 bit 7-4 PSEL3: PSEL2: PSEL1: PSEL0: Positive Channel Select 0000 = AIN0 (default) 0001 = AIN1 0010 = AIN2 0011 = AIN3 0100 = AIN4 0101 = AIN5 0110 = AIN6 0111 = AIN7 1xxx = AINCOM (except when all bits are 1’s) 1111 = Temperature Sensor Diode Anode bit 3-0 NSEL3: NSEL2: NSEL1: NSEL0: Negative Channel Select 0000 = AIN0 0001 = AIN1 (default) 0010 = AIN2 0011 = AIN3 0100 = AIN4 0101 = AIN5 0110 = AIN6 0111 = AIN7 1xxx = AINCOM (except when all bits are 1’s) 1111 = Temperature Sensor Diode Cathode Analog GND ADS1218 SBAS187 BOCS bit 7 bit 6 bit 5 bit 4 IDAC2R1 IDAC2R0 IDAC1R1 bit 3 bit 2 bit 1 bit 0 IDAC1R0 PGA2 PGA1 PGA0 BOCS: Burnout Current Source 0 = Disabled (default) 1 = Enabled VREF RANGE −1 IDAC Current = (DAC Code) 2 8 • R DAC ( ) bit 6-5 IDAC2R1: IDAC2R0: Full-Scale Range Select for IDAC2 00 = Off (default) 01 = Range 1 10 = Range 2 11 = Range 3 bit 4-3 IDAC1R1: IDAC1R0: Full-Scale Range Select for IDAC1 00 = Off (default) 01 = Range 1 10 = Range 2 11 = Range 3 bit 2-0 PGA2: PGA1: PGA0: Programmable Gain Amplifier Gain Selection 000 = 1 (default) 001 = 2 010 = 4 011 = 8 100 = 16 101 = 32 110 = 64 111 = 128 IDAC1 (Address 03H) Current DAC 1 Reset Value = 00H bit 7 bit 6 IDAC1_7 IDAC1_6 bit 5 bit 4 IDAC1_5 IDAC1_4 bit 3 bit 2 IDAC1_3 IDAC1_2 bit 1 bit 0 IDAC1_1 IDAC1_0 The DAC code bits set the output of DAC1 from 0 to fullscale. The value of the full-scale current is set by this Byte, VREF, RDAC, and the DAC1 range bits in the ACR register. IDAC2 (Address 04H) Current DAC 2 Reset Value = 00H bit 7 bit 6 IDAC2_7 IDAC2_6 bit 5 bit 4 IDAC2_5 IDAC2_4 bit 3 bit 2 IDAC1_3 IDAC1_2 bit 1 bit 0 IDAC1_1 IDAC1_0 The DAC code bits set the output of DAC2 from 0 to fullscale. The value of the full-scale current is set by this Byte, VREF, RDAC, and the DAC2 range bits in the ACR register. 17 ODAC (Address 05H) Offset DAC Setting Reset Value = 00H bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SIGN OSET6 OSET5 OSET4 OSET3 OSET2 OSET1 OSET0 bit 7 Offset Sign 0 = Positive 1 = Negative bit 6-0 Offset = VREF Code • 2 • PGA 127 NOTE: Calibration will cancel the value in the ODAC register. Therefore, writing to the ODAC register should be done after calibration. DIO (Address 06H) Digital I/O Reset Value = 00H bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 DIO7 DIO6 DIO5 DIO4 DIO3 DIO2 DIO1 DIO0 A value written to this register will appear on the digital I/O pins if the pin is configured as an output in the DIR register. Reading this register will return the value of the digital I/O pins. DIR (Address 07H) Direction control for digital I/O Reset Value = FFH bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 DIR7 DIR6 DIR5 DIR4 DIR3 DIR2 DIR1 DIR0 Each bit controls whether the Digital I/O pin is an output (= 0) or input (= 1). The default power-up state is as inputs. DEC0 (Address 08H) Decimation Register (Least Significant 8 bits) Reset Value = 80H bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 DEC07 DEC06 DEC05 DEC04 DEC03 DEC02 DEC01 DEC00 The decimation value is defined with 11 bits for a range of 20 to 2047. This register is the least significant 8 bits. The 3 most significant bits are contained in the M/DEC1 register. The default data rate is 10Hz with a 2.4576MHz crystal. M/DEC1 (Address 09H) Mode and Decimation Register Reset Value = 07H bit 7 bit 6 DRDY U/B bit 5 bit 4 SMODE1 SMODE0 bit 3 bit 2 bit 1 bit 0 WREN DEC10 DEC09 DEC08 bit 7 DRDY: Data Ready (Read Only) This bit duplicates the state of the DRDY pin. bit 6 U/B: Data Format 0 = Bipolar (default) 1 = Unipolar U/B 0 1 18 ANALOG INPUT DIGITAL OUTPUT +FSR Zero –FSR +FSR Zero –FSR 0x7FFFFF 0x000000 0x800000 0xFFFFFF 0x000000 0x000000 bit 5-4 SMODE1: SMODE0: Settling Mode 00 = Auto (default) 01 = Fast Settling filter 10 = Sinc2 filter 11 = Sinc3 Flash filter bit 3 WREN: Write Enable 0 = Flash Writing Disabled (default) 1 = Flash Writing Enabled This bit is AND’d with the WREN pin to enable or disable Flash Writing and Erasing bit 2-0 DEC10: DEC09: DEC08: Most Significant Bits of the Decimation Value OCR0 (Address 0AH) Offset Calibration Coefficient (Least Significant Byte) Reset Value = 00H bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 OCR07 OCR06 OCR05 OCR04 OCR03 OCR02 OCR01 OCR00 OCR1 (Address 0BH) Offset Calibration Coefficient (Middle Byte) Reset Value = 00H bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 OCR15 OCR14 OCR13 OCR12 OCR11 OCR10 OCR09 OCR08 OCR2 (Address 0CH) Offset Calibration Coefficient (Most Significant Byte) Reset Value = 00H bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 OCR23 OCR22 OCR21 OCR20 OCR19 OCR18 OCR17 OCR16 FSR0 (Address 0DH) Full-Scale Register (Least Significant Byte) Reset Value = 24H bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 FSR07 FSR06 FSR05 FSR04 FSR03 FSR02 FSR01 FSR00 FSR1 (Address 0EH) Full-Scale Register (Middle Byte) Reset Value = 90H bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 FSR15 FSR14 FSR13 FSR12 FSR011 FSR10 FSR09 FSR08 FSR2 (Address 0FH) Full-Scale Register (Most Significant Byte) Reset Value = 67H bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 FSR23 FSR22 FSR21 FSR20 FSR019 FSR18 FSR17 FSR16 ADS1218 SBAS187 COMMAND DEFINITIONS Operands: The commands listed below control the operation of the ADS1218. Some of the commands are stand-alone commands (e.g., RESET) while others require additional bytes (e.g., WREG requires command, count, and the data bytes). Commands that output data require a minimum of four fOSC cycles before the data is ready (e.g., RDATA). COMMANDS DESCRIPTION RDATA RDATAC STOPC RREG RRAM CREG CREGA WREG WRAM RF2R WR2F CRAM CSRAMX CSARAMX CSREG CSRAM CSARAM CSFL SELFCAL SELFOCAL SELFGCAL SYSOCAL SYSGCAL DSYNC SLEEP RESET Read Data Read Data Continuously Stop Read Data Continuously Read from REG Bank “rrrr” Read from RAM Bank “aaa” Copy REGs to RAM Bank “aaa” Copy REGS to all RAM Banks Write to REG “rrrr” Write to RAM Bank “aaa” Read FLASH page to RAM Write RAM to FLASH page Copy RAM Bank “aaa” to REG Calc RAM Bank “aaa” Checksum Calc all RAM Bank Checksum Calc REG Checksum Calc RAM Bank “aaa” Checksum Calc all RAM Banks Checksum Calc FLASH Checksum Self Cal Offset and Gain Self Cal Offset Self Cal Gain Sys Cal Offset Sys Cal Gain Sync DRDY Put in SLEEP Mode Reset to Power-Up Values n = count (0 to 127) r = register (0 to 15) x = don’t care a = RAM bank address (0 to 7) f = FLASH page address (0 to 31) COMMAND BYTE 0000 0000 0000 0001 0010 0100 0100 0101 0110 100f 101f 1100 1101 1101 1101 1110 1110 1110 1111 1111 1111 1111 1111 1111 1111 1111 2ND COMMAND BYTE 0001 (01H) 0011 (03H) 1111 (0FH) r r r r (1x H) 0aaa (2x H) 0aaa (4x H) 1000 (48H) r r r r (5x H) 0aaa (6x H) f f f f (8, 9xH) f f f f (A, BxH) 0aaa (CxH) 0aaa (DxH) 1000 (D8 H) 1111 (DFH) 0aaa (ExH) 1000 (E8H) 1100 (ECH) 0000 (F0H) 0001 (F1H) 0010 (F2H) 0011 (F3H) 0100 (F4H) 1100 (FCH) 1101 (FDH) 1110 (FE H) — — — xxxx_nnnn (# of reg-1) xnnn_nnnn (# of bytes-1) — — xxxx_nnnn (# of reg-1) xnnn_nnnn (# of bytes-1) — — — — — — — — — — — — — — — — — NOTE: (1) The data received by the A/D is always MSB First, the data out format is set by the BIT ORDER bit in ACR reg. TABLE III. Command Summary. RDATA Read Data RDATAC Description: Read a single data value from the Data Output Register (DOR) which is the most recent conversion result. This is a 24-bit value. Operands: None Bytes: 1 Encoding: 0000 0001 Data Transfer Sequence: DIN 0000 0001 • • •(1) xxxx xxxx xxxx xxxx xxxx xxxx DOUT xxxx xxxx • • •(1) MSB Mid-Byte LSB Read Data Continuous Description: Read Data Continuous mode enables the continuous output of new data on each DRDY. This command eliminates the need to send the Read Data Command on each DRDY. This mode may be terminated by either the STOP Read Continuous command or the RESET command. Operands: None Bytes: 1 Encoding: 0000 0011 Data Transfer Sequence: Command terminated when “uuuu uuuu” equals STOPC or RESET. DIN 0000 0011 • • •(1) uuuu uuuu uuuu uuuu uuuu uuuu DOUT xxxx xxxx • • •(1) MSB Mid-Byte LSB NOTE: (1) For wait time, refer to timing specification. ••• DRDY ••• DIN xxxx xxxx xxxx MSB Mid-Byte LSB ••• DOUT NOTE: (1) For wait time, refer to timing specification. ADS1218 SBAS187 19 STOPC Stop Continuous CREG Description: Ends the continuous data output mode. Operands: None Bytes: 1 Encoding: 0000 1111 Data Transfer Sequence: RREG DIN 0000 1111 DOUT xxxx xxxx Copy Registers to RAM Bank Description: Copy the 16 control registers to the RAM bank specified in the op code. Refer to timing specifications for command execution time. Operands: a Bytes: 1 Encoding: 0100 0aaa Data Transfer Sequence: Copy Register Values to RAM Bank 3 Read from Registers Description: Output the data from up to 16 registers starting with the register address specified as part of the instruction. The number of registers read will be one plus the second byte. If the count exceeds the remaining registers, the addresses will wrap back to the beginning. Operands: r, n Bytes: 2 Encoding: 0001 rrrr xxxx nnnn Data Transfer Sequence: Read Two Registers Starting from Register 01H (MUX) DIN 0001 0001 0000 0001 • • •(1) xxxx xxxx xxxx xxxx DOUT xxxx xxxx xxxx xxxx • • •(1) MUX ACR CREGA DIN 0100 0011 DOUT xxxx xxxx Copy Registers to All RAM Banks Description: Duplicate the 16 control registers to all the RAM banks. Refer to timing specifications for command execution time. Operands: None Bytes: 1 Encoding: 0100 1000 Data Transfer Sequence: DIN 0100 1000 DOUT xxxx xxxx NOTE: (1) For wait time, refer to timing specification. WREG RRAM Read from RAM Description: Up to 128 bytes can be read from RAM starting at the bank specified in the op code. All reads start at the address for the beginning of the RAM bank. The number of bytes to read will be one plus the value of the second byte. Operands: a, n Bytes: 2 Encoding: 0010 0aaa xnnn nnnn Data Transfer Sequence: Read Two RAM Locations Starting from 20H DIN 0010 0010 x000 0001 • • •(1) xxxx xxxx xxxx xxxx DOUT xxxx xxxx xxxx xxxx • • •(1) RAM Data 20H RAM Data 21H Write to Register Description: Write to the registers starting with the register specified as part of the instruction. The number of registers that will be written is one plus the value of the second byte. Operands: r, n Bytes: 2 Encoding: 0101 rrrr xxxx nnnn Data Transfer Sequence: Write Two Registers Starting from 06H (DIO) DIN 0101 0110 xxxx 0001 Data for DIO Data for DIR DOUT xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx NOTE: (1) For wait time, refer to timing specification. 20 ADS1218 SBAS187 WRAM Write to RAM CRAM Description: Write up to 128 RAM locations starting at the beginning of the RAM bank specified as part of the instruction. The number of bytes written is RAM is one plus the value of the second byte. Operands: a, n Bytes: 2 Encoding: 0110 0aaa xnnn nnnn Data Transfer Sequence: Write to Two RAM Locations starting from 10H DIN 0110 0001 x000 0001 Data for 10H Data for 11H DOUT xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx Description: Copy the selected RAM Bank to the Configuration Registers. This will overwrite all of the registers with the data from the RAM bank. Operands: a Bytes: 1 Encoding: 1100 0aaa Data Transfer Sequence: Copy RAM Bank 0 to the Registers CSRAMX RF2R Read FLASH Page to RAM Description: Read the selected FLASH page to the RAM. Operands: f Bytes: 1 Encoding: 100f ffff Data Transfer Sequence: Read FLASH Page 2 to RAM DIN 1000 0010 DOUT xxxx xxxx Copy RAM Bank to Registers DIN 1100 0000 DOUT xxxx xxxx Calculate RAM Bank Checksum Description: Calculate the checksum of the selected RAM Bank. The checksum is calculated as a sum of all the bytes with the carry ignored. The ID, DRDY and DIO bits are masked so they are not included in the checksum. Operands: a Bytes: 1 Encoding: 1101 0aaa Data Transfer Sequence: Calculate Checksum for RAM Bank 3 DIN 1101 0011 DOUT xxxx xxxx WR2F Write RAM to FLASH Description: Write the contents of RAM to the selected FLASH page. Operands: f Bytes: 1 Encoding: 101f ffff Data Transfer Sequence: Write RAM to FLASH page 31 ADS1218 SBAS187 DIN 1011 1111 DOUT xxxx xxxx CSARAMX Calculate the Checksum for all RAM Banks Description: Calculate the checksum of all RAM Banks. The checksum is calculated as a sum of all the bytes with the carry ignored. The ID, DRDY and DIO bits are masked so they are not included in the checksum. Operands: None Bytes: 1 Encoding: 1101 1000 Data Transfer Sequence: DIN 1101 1000 DOUT xxxx xxxx 21 CSREG Calculate the Checksum of Registers Description: Calculate the checksum of all the registers. The checksum is calculated as a sum of all the bytes with the carry ignored. The ID, DRDY and DIO bits are masked so they are not included in the checksum. Operands: None Bytes: 1 Encoding: 1101 1111 Data Transfer Sequence: DIN DOUT CSFL Calculate Checksum for all FLASH Pages Description: Calculate the checksum for all FLASH pages. The checksum is calculated as a sum of all the bytes with the carry ignored. All bits are included in the checksum calculation, there is no masking of bits. Operands: None Bytes: 1 Encoding: 1110 1100 Data Transfer Sequence: Calculate RAM Bank Checksum Description: Calculate the checksum of the selected RAM Bank. The checksum is calculated as a sum of all the bytes with the carry ignored. All bits are included in the checksum calculation, there is no masking of bits. Operands: a Bytes: 1 Encoding: 1110 0aaa Data Transfer Sequence: Calculate Checksum for RAM Bank 2 CSARAM DIN 1110 0010 DOUT xxxx xxxx Calculate Checksum for all RAM Banks Description: Calculate the checksum of all RAM Banks. The checksum is calculated as a sum of all the bytes with the carry ignored. All bits are included in the checksum calculation, there is no masking of bits. Operands: None Bytes: 1 Encoding: 1110 1000 Data Transfer Sequence: 22 1110 1100 DOUT xxxx xxxx xxxx xxxx SELFCAL CSRAM DIN 1101 1111 DIN 1110 1000 DOUT xxxx xxxx Offset and Gain Self Calibration Description: Starts the process of self calibration. The Offset Control Register (OCR) and the Full-Scale Register (FSR) are updated with new values after this operation. Operands: None Bytes: 1 Encoding: 1111 0000 Data Transfer Sequence: DIN 1111 0000 DOUT xxxx xxxx SELFOCAL Offset Self Calibration Description: Starts the process of self-calibration for offset. The Offset Control Register (OCR) is updated after this operation. Operands: None Bytes: 1 Encoding: 1111 0001 Data Transfer Sequence: DIN 1111 0001 DOUT xxxx xxxx ADS1218 SBAS187 SELFGCAL Gain Self Calibration DSYNC Description: Starts the process of self-calibration for gain. The Full-Scale Register (FSR) is updated with new values after this operation. Description: Synchronizes the ADS1218 to the serial clock edge. Operands: None Bytes: 1 Encoding: 1111 0010 Data Transfer Sequence: DIN 1111 0010 DOUT xxxx xxxx Operands: None Bytes: 1 Encoding: 1111 1100 Data Transfer Sequence: SLEEP SYSOCAL System Offset Calibration Description: Starts the system offset calibration process. For a system offset calibration the input should be set to 0V differential, and the ADS1218 computes the OCR register value that will compensate for offset errors. The Offset Control Register (OCR) is updated after this operation. SYSGCAL 1111 0011 DOUT xxxx xxxx Description: Starts the system gain calibration process. For a system gain calibration, the differential input should be set to the reference voltage and the ADS1218 computes the FSR register value that will compensate for gain errors. The FSR is updated after this operation. Operands: None Bytes: 1 Encoding: 1111 0100 Data Transfer Sequence: ADS1218 SBAS187 DIN 1111 0100 DOUT xxxx xxxx 1111 1100 DOUT xxxx xxxx Sleep Mode Operands: None Bytes: 1 Encoding: 1111 1101 Data Transfer Sequence: RESET System Gain Calibration DIN Description: Puts the ADS1218 into a low power sleep mode. To exit sleep mode strobe SCLK. Operands: None Bytes: 1 Encoding: 1111 0011 Data Transfer Sequence: DIN Sync DRDY DIN 1111 1101 DOUT xxxx xxxx Reset to Powerup Values Description: Restore the registers to their power-up values. This command will also stop the Read Continuous mode. It does not affect the contents of RAM. Operands: None Bytes: 1 Encoding: 1111 1110 Data Transfer Sequence: DIN 1111 1110 DOUT xxxx xxxx 23 LSB MSB 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 0000 x rdata x rdatac x x x x x x x x x x x stopc 0001 rreg 0 rreg 1 rreg 2 rreg 3 rreg 4 rreg 5 rreg 6 rreg 7 rreg 8 rreg 9 rreg A rreg B rreg C rreg D rreg E rreg F 0010 rram 0 rram 1 rram 2 rram 3 rram 4 rram 5 rram 6 rram 7 x x x x x x x x 0011 x x x x x x x x x x x x x x x x 0100 creg 0 creg 1 creg 2 creg 3 creg 4 creg 5 creg 6 creg 7 crega x x x x x x x 0101 wreg 0 wreg 1 wreg 2 wreg 3 wreg 4 wreg 5 wreg 6 wreg 7 wreg 8 wreg 9 wreg A wreg B wreg C wreg D wreg E wreg F 0110 wram 0 wram 1 wram 2 wram 3 wram 4 wram 5 wram 6 wram 7 x x x x x x x x 0111 x x x x x x x x x x x x x x x x 1000 rf2r 0 r f2r 1 r f2r 2 r f2r 3 r f2r 4 rf2r 5 r f2r 6 rf2r 7 rf2r 8 r f2r 9 rf2r A rf2r B rf2r C r f2r D rf2r E r f2r F 1001 r f2r 10 r f2r 11 r f2r 12 r f2r 13 r f2r 14 rf2r 15 r f2r 16 rf2r 17 rf2r 18 r f2r 19 rf2r 1A rf2r 1B rf2r 1C r f2r 1D rf2r 1E r f2r 1F 1010 w r2f 0 w r2f 1 w r2f 2 w r2f 3 w r2f 4 wr 2f 5 w r 2f 6 wr 2f 7 wr 2f 8 w r 2f 9 wr 2f A wr 2f B wr 2f C w r 2f D wr 2f E w r 2f F 1011 w r2f 10 w r2f 11 w r2f 12 w r2f 13 w r2f 14 wr 2f 15 w r 2f 16 wr 2f 17 wr 2f 18 w r 2f 19 wr 2f 1A wr 2f 1B wr 2f 1C w r 2f 1D wr 2f 1E w r 2f 1F cram 7 x x x x x x x x x x x x x x csreg x x x csfl x x x x x x dsync sleep reset x 1100 cram 0 cram 1 cram 2 cram 3 cram 4 cram 5 cram 6 1101 csramx csramx 0 1 csramx csramx csramx csramx csramx 2 3 4 5 6 csramx csramx 7 1110 csram 0 csram 1 csram2 csram 3 csram 4 csram 5 csram 6 csram 7 1111 self cal self ocal self gcal sys ocal sys gcal x x x csram x x = Reserved TABLE IV. ADS1218 Command Map. 24 ADS1218 SBAS187 SERIAL PERIPHERAL INTERFACE The Serial Peripheral Interface (SPI), allows a controller to communicate synchronously with the ADS1218. The ADS1218 operates in slave only mode. SPI Transfer Formats During an SPI transfer, data is simultaneously transmitted and received. The SCLK signal synchronizes shifting and sampling of the information on the two serial data lines: DIN and DOUT. The CS signal allows individual selection of an ADS1218 device; an ADS1218 with CS HIGH is not active on the bus. Clock Phase and Polarity Controls (POL) The clock polarity is specified by the POL pin, which selects an active HIGH or active LOW clock, and has no effect on the transfer format. Serial Clock (SCLK) SCLK, a Schmitt Trigger input to the ADS1218, is generated by the master device and synchronizes data transfer on the DIN and DOUT lines. When transferring data to or from the ADS1218, burst mode may be used i.e., multiple bits of data may be transferred back-to-back with no delay in SCLKs or toggling of CS. Chip Select (CS) The chip select (CS) input of the ADS1218 must be externally asserted before a master device can exchange data with the ADS1218. CS must be LOW before data transactions and must stay LOW for the duration of the transaction. DIGITAL INTERFACE The ADS1218’s programmable functions are controlled using a set of on-chip registers, as outlined previously. Data is written to these registers via the part’s serial interface and read access to the on-chip registers is also provided by this interface. The ADS1218’s serial interface consists of four signals: CS, SCLK, DIN, and DOUT. The DIN line is used for transferring data into the on-chip registers while the DOUT line is used for accessing data from the on-chip registers. SCLK is the serial clock input for the device and all data transfers (either on DIN or DOUT) take place with respect to this SCLK signal. The DRDY line is used as a status signal to indicate when data is ready to be read from the ADS1218’s data register. DRDY goes LOW when a new data word is available in the DOR register. It is reset HIGH when a read operation from the data register is complete. It also goes HIGH prior to the updating of the output register to indicate when not to read from the device to ensure that a data read is not attempted while the register is being updated. ADS1218 SBAS187 CS is used to select the device. It can be used to decode the ADS1218 in systems where a number of parts are connected to the serial bus. The timing specification shows the timing diagram for interfacing to the ADS1218 with CS used to decode the part. The ADS1218 serial interface can operate in three-wire mode by tying the CS input LOW. In this case, the SCLK, DIN, and DOUT lines are used to communicate with the ADS1218 and the status of DRDY can be obtained by interrogating bit 7 of the M/DEC1 register. This scheme is suitable for interfacing to microcontrollers. If CS is required as a decoding signal, it can be generated from a port pin. DEFINITION OF TERMS Analog Input Voltage—the voltage at any one analog input relative to AGND. Analog Input Differential Voltage—given by the following equation: (IN+ – IN–). Thus, a positive digital output is produced whenever the analog input differential voltage is positive, while a negative digital output is produced whenever the differential is negative. For example, when the converter is configured with a 2.5V reference and placed in a gain setting of 1, the positive full-scale output is produced when the analog input differential is 2.5V. The negative full-scale output is produced when the differential is –2.5V. In each case, the actual input voltages must remain within the AGND to AVDD range. Conversion Cycle—the term “conversion cycle” usually refers to a discrete A/D conversion operation, such as that performed by a successive approximation converter. As used here, a conversion cycle refers to the tDATA time period. However, each digital output is actually based on the modulator results from several tDATA time periods. FILTER SETTING MODULATOR RESULTS fast settling 1 tDATA time period sinc2 2 tDATA time period sinc3 3 tDATA time period Data Rate—The rate at which conversions are completed. See definition for fDATA. Decimation Ratio—defines the ratio between the output of the modulator and the output Data Rate. Valid values for the Decimation Ratio are from 20 to 2047. Larger Decimation Ratios will have lower noise and vice-versa. 25 Effective Resolution—the effective resolution of the ADS1218 in a particular configuration can be expressed in two different units: bits rms (referenced to output) and Vrms (referenced to input). Computed directly from the converter’s output data, each is a statistical calculation. The conversion from one to the other is shown below. BITS rms PGA SETTING SAMPLING FREQUENCY 1, 2, 4, 8 f SAMP = fOSC mfactor BIPOLAR Vrms UNIPOLAR Vrms 16 f SAMP = fOSC • 2 mfactor 2 • VREF PGA VREF PGA 32 f SAMP = fOSC • 4 mfactor 64, 128 f SAMP = fOSC • 8 mfactor 10 6.02 • ER 20 10 6.02 • ER 20 24 298nV 22 1.19µV 597nV 20 4.77µV 2.39µV 18 19.1µV 9.55µV 16 76.4µV 38.2µV 14 505µV 152.7µV 12 1.22mV 610µV 149nV Filter Selection—the ADS1218 uses a (sinx /x) filter or sinc filter. Actually there are three different sinc filters that can be selected. A fast settling filter will settle in one tDATA cycle. The sinc2 filter will settle in two cycles and have lower noise. The sinc3 will achieve the lowest noise and highest number of effective bits, but requires three cycles to settle. The ADS1218 will operate with any one of these filters, or it can operate in an auto mode, where it will select the fast settling filter after a new channel is selected and will then switch to sinc2 followed by sinc3. This allows fast settling response and still achieves low noise after the necessary number of tDATA cycles. fOSC—the frequency of the crystal oscillator or CMOS compatible input signal at the XIN input of the ADS1218. fMOD—the frequency or speed at which the modulator of the ADS1218 is running. This depends on the SPEED bit as given by the following equation: SPEED = 0 SPEED = 1 128 256 mfactor fMOD = fSAMP—the frequency, or switching speed, of the input sampling capacitor. The value is given by one of the following equations: fDATA—the frequency of the digital output data produced by the ADS1218, fDATA is also referred to as the Data Rate. fMOD fOSC fDATA = = Decimation Ratio mfactor • Decimation Ratio Full-Scale Range (FSR)—as with most A/D converters, the full-scale range of the ADS1218 is defined as the “input”, which produces the positive full-scale digital output minus the “input”, which produces the negative full-scale digital output. The full-scale range changes with gain setting as shown in Table V. For example, when the converter is configured with a 2.5V reference and is placed in a gain setting of 2, the full-scale range is: [1.25V (positive full-scale) minus –1.25V (negative full-scale)] = 2.5V. Least Significant Bit (LSB) Weight—this is the theoretical amount of voltage that the differential voltage at the analog input would have to change in order to observe a change in the output data of one least significant bit. It is computed as follows: Full − Scale Range LSB Weight = 2N where N is the number of bits in the digital output. tDATA—the inverse of fDATA, or the period between each data output. fOSC mfactor 5V SUPPLY ANALOG INPUT(1) GAIN SETTING FULL-SCALE RANGE DIFFERENTIAL INPUT VOLTAGES(2) GENERAL EQUATIONS PGA OFFSET RANGE FULL-SCALE RANGE DIFFERENTIAL INPUT VOLTAGES(2) 2 • VREF PGA ±VREF PGA 1 5V ±2.5V ±1.25V 2 2.5V ±1.25V ±0.625V 4 1.25V ±0.625V ±312.5mV 8 0.625V ±312.5mV ±156.25mV 16 312.5mV ±156.25mV ±78.125mV 32 156.25mV ±78.125mV ±39.0625mV 64 78.125mV ±39.0625mV ±19.531mV 128 39.0625mV ±19.531mV ±9.766mV PGA SHIFT RANGE ± VREF 2 • PGA NOTES: (1) With a 2.5V reference. (2) The ADS1218 allows common-mode voltage as long as the absolute input voltage on AINP or AINN does not go below AGND or above AVDD. TABLE V. Full-Scale Range versus PGA Setting. 26 ADS1218 SBAS187 TOPIC INDEX TOPIC PAGE ABSOLUTE MAXIMUM RATINGS .......................................................................................................................... 2 PACKAGE AND ORDERING INFORMATION ........................................................................................................ 2 ELECTRICAL CHARACTERISTICS (AVDD = 5V) .................................................................................................. 2 ELECTRICAL CHARACTERISTICS (AVDD = 3V) .................................................................................................. 4 PIN CONFIGURATION ............................................................................................................................................ 6 TIMING SPECIFICATIONS ...................................................................................................................................... 7 TYPICAL CHARACTERISTICS ............................................................................................................................... 8 OVERVIEW .............................................................................................................................................................12 MEMORY ................................................................................................................................................................15 REGISTER BANK TOPOLOGY ............................................................................................................................15 DETAILED REGISTER DEFINITIONS ..................................................................................................................17 COMMAND DEFINITIONS .....................................................................................................................................19 ADS1218 COMMAND MAP ...................................................................................................................................24 SERIAL PERIPHERAL INTERFACE .....................................................................................................................25 DIGITAL INTERFACE ............................................................................................................................................25 DEFINITION OF TERMS ........................................................................................................................................25 ADS1218 SBAS187 27 PACKAGE DRAWING MTQF019A – JANUARY 1995 – REVISED JANUARY 1998 PFB (S-PQFP-G48) PLASTIC QUAD FLATPACK 0,27 0,17 0,50 36 0,08 M 25 37 24 48 13 0,13 NOM 1 12 5,50 TYP 7,20 SQ 6,80 9,20 SQ 8,80 Gage Plane 0,25 0,05 MIN 0°– 7° 1,05 0,95 Seating Plane 1,20 MAX 0,75 0,45 0,08 4073176 / B 10/96 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Falls within JEDEC MS-026 28 ADS1218 SBAS187 PACKAGE OPTION ADDENDUM www.ti.com 3-Oct-2003 PACKAGING INFORMATION ORDERABLE DEVICE STATUS(1) PACKAGE TYPE PACKAGE DRAWING PINS PACKAGE QTY ADS1218Y/250 ACTIVE TQFP PFB 48 250 ADS1218Y/2K ACTIVE TQFP PFB 48 2000 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Applications amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2003, Texas Instruments Incorporated