8 PIN SOP 200 V BREAK DOWN VOLTAGE 2-CH OPTICAL COUPLED MOSFET PS7221-2A FEATURES DESCRIPTION • 2 CHANNEL TYPE: 1a + 1a Output • DESIGNED FOR AC/DC SWITCHING LINE CHANGER PS7221-2A is a solid state relay containing a GaAs LED on the light emitting side (input side) and MOSFETs on the output side. • SMALL PACKAGE: 8 PIN SOP This device is suitable for analog signal control because of its low offset and high linearity. • HIGH ISOLATION VOLTAGE: BV: 1500 Vr.m.s. MIN. • LOW OFFSET VOLTAGE APPLICATIONS • LOW LED OPERATING CURRENT: IF = 2 mA • EXCHANGE EQUIPMENT • AVAILABLE IN TAPE AND REEL • MEASUREMENT EQUIPMENT • FA/OA EQUIPMENT ELECTRICAL CHARACTERISTICS (TA = 25°C) PART NUMBER MOSFET Diode SYMBOLS PS7221-2A PARAMETERS UNITS VF Forward Voltage, IF = 10 mA V IR Reverse Current, VR = 5 V µA TYP MAX 1.2 1.4 5.0 ILoff Off-State Leakage Current, VD = 200 V µA 0.03 COUT Output Capacitance, VD = 0 V, f = 1 MHz pF/ch 88 IFon LED On-state Current, IL = 150 mA Ron1 On-State Resistance, Ron2 1.0 mA IF = 10 mA, IL = 10 mA Coupled MIN 2.0 Ω 4.0 8.0 IF = 10 mA, IL = 150 mA, t ≤10 ms ton Turn-On Time1, IF = 10 mA, VO = 5 V, PW ≥ 10 ms ms 0.16 1.0 toff Turn-Off Time1, IF = 10 mA, VO = 5 V, PW ≥ 10 ms ms 0.02 0.2 Rl-O Isolation Resistance, Vin-out = 1.0 kVDC Ω Cl-O Isolation Capacitance, V = 0 V, f = 1 MHz 109 pF/ch 0.4 Notes: 1. Test Circuiit for Switching Time: PS7221-2A IF Pulse Input VL Input 50% 8 7 6 5 1 2 3 4 0 Input Monitor VO Monitor Rin RL VO = 5 V 90% Output 10% ton toff California Eastern Laboratories PS7221-2A ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) SYMBOLS PARAMETERS Diode VR Reverse Voltage IF Forward Current (DC) PD Power Dissipation UNITS RATINGS V mA mW/ch 5.0 50 50 A 1 V mA 200 150 mA mW/ch 400 180 Vr.m.s. mW °C °C 1500 460 -40 to +100 -40 to +80 RECOMMENDED OPERATING CONDITIONS (TA = 25 °C) SYMBOL IF (Peak) Peak Forward Current2 MOSFET VL Break Down Voltage IL Continuous Load Current ILP Pulse Load Current3 AC/DC Connection PD Power Dissipation Coupled BV Isolation Voltage4 PT Total Power Dissipation TSTG Storage Temperature TA Operating Ambient Temp. Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. PW = 100 µs, Duty Cycle = 1 % 3. PW = 100 ms, 1 shot. 4. AC voltage for 1 minute at TA = 25 °C, RH = 60 % between input and output. PARAMETER UNITS MIN TYP MAX IF LED Operating Current VF LED Off Voltage mA 2 V 0 10 20 0.5 ORDERING INFORMATION PART NUMBER PS7221-2A PS7221-2A-F3 PS7221-2A-F4 PACKAGE 8-pin SOP PACKING STYLE Magazine case 45 pcs Embossed Tape 1500 pcs/reel OUTLINE DIMENSIONS (Units in mm) 9.08±0.5 8 TOP VIEW 7 6 5 1 2 4 0.4±0.3 3 7.0±0.3 4.4 0.15 +0.10 -0.05 2.05 +0.08 -0.05 2.54 0.40 +0.10 -0.05 0.5 +0.08 -0.05 0.5±0.3 0.25 M 1. LED Anode 1 5. MOSFET 2 2. LED Cathode 1 6. MOSFET 2 3. LED Anode 2 7. MOSFET 1 4. LED Cathode 2 8. MOSFET 1 TYPICAL PERFORMANCE CURVES (TA = 25 °C) MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE MAXIMUM LOAD CURRENT vs. AMBIENT TEMPERATURE 300 Maximum Load Current, IL (mA) Maximum Forward Current, IF (mA) 100 80 60 40 20 0 -25 0 25 50 75 80 Ambient Temperature, TA (°C) 100 250 200 150 100 50 0 -25 0 25 50 75 80 Ambient Temperature, TA (°C) 100 PS7221-2A TYPICAL PERFORMANCE CURVES (TA = 25 °C) FORWARD VOLTAGE vs. AMBIENT TEMPERATURE OUTPUT CAPACITANCE vs. APPLIED VOLTAGE 125 1.6 1.4 IF = 50 mA 30 mA 1.2 20 mA 10 mA 5 mA 1.0 1 mA 0.8 -25 0 25 50 75 Output Capacitance (pF) Forward Voltage, VF (V) f = 1 MHz 100 75 50 25 0 100 20 NORMALIZED ON-STATE RESISTANCE vs. AMBIENT TEMPERATURE 100 120 ON-STATE RESISTANCE DISTRIBUTION Normalized to 1.0 at TA = 25°C IF = 10 mA, IL = 10 mA 2.5 Number (pcs) 2.0 1.5 1.0 n = 50 pcs, IF = 10 mA, IL = 10 mA 25 20 15 10 5 0.5 0 -25 0 25 50 75 3.6 100 3.8 4.0 4.2 4.4 Ambient Temperature, TA (°C) On-State Resistance, Ron (Ω) OFF-STATE LEAKAGE CURRENT vs. SUPPLY VOLTAGE LOAD CURRENT vs. LOAD VOLTAGE -4 IF = 10 mA 200 10-5 TA = 80°C 10 Load Current, IL (mA) Normalized On-State Resistance, Ron Off-State Leakage Current, ILoff (A) 80 3.0 3.0 10 60 Applied Voltage, VD (V) Ambient Temperature, TA (°C) 0.0 40 -6 10-7 25°C 10-8 10 100 -1.0 -0.5 0 0.5 -100 -9 -200 10-10 0 50 100 150 200 Supply Voltage, VCC (V) 250 Load Voltage, VL (V) 1.0 PS7221-2A TYPICAL PERFORMANCE CURVES (TA = 25 °C) TURN-ON TIME vs. FORWARD CURRENT TURN-OFF TIME vs. FORWARD CURRENT 2.5 0.5 VO = 5 V 2.0 Turn-Off Time, toff (ms) Turn-On Time, ton (ms) VO = 5 V 1.5 1.0 0.5 0 5 10 20 15 25 0.3 0.2 0.1 0 30 5 25 TURN-ON TIME DISTRIBUTION TURN-OFF TIME DISTRIBUTION 30 30 n = 50 pcs, IF = 10 mA VO= 5 V n = 50 pcs, IF = 10 mA, VO = 5 V 25 Number (pcs) 20 15 10 20 15 10 5 5 0 0 0.04 0.02 0.24 0.16 Turn-On Time, ton (ms) Turn-Off Time, toff (ms) NORMALIZED TURN-OFF TIME vs. AMBIENT TEMPERATURE NORMALIZED TURN-ON TIME vs. AMBIENT TEMPERATURE 3.0 Normalized to 1.0 at TA = 25°C IF = 10 mA, VO = 5V 2.5 2.0 1.5 1.0 0.5 Normalized Turn-Off Time, toff 3.0 Normalized Turn-On Time, ton 20 15 Forward Current, IF (mA) 25 0.0 10 Forward Current, IF (mA) 30 Number (pcs) 0.4 2.5 2.0 1.5 1.0 0.5 0.0 -25 0 25 50 75 Ambient Temperature, TA (°C) 100 Normalized to 1.0 at TA = 25°C IF = 10 mA, VO = 5 V -25 0 25 50 75 Ambient Temperature, TA (°C) 100 PS7221-2A TAPING SPECIFICATIONS (Units in mm) OUTLINE AND DIMENSIONS (TAPE) OUTLINE AND DIMENSIONS (REEL) 2.0 ± 0.1 1.75 ± 0.1 4.0 ± 0.1 2.8 ± 0.1 1.55 ± 0.1 φ21.0 ± 0.8 7.5 ± 0.1 2.0 ± 0.5 φ100±5.0 φ330 10.45 ± 0.1 φ13.0±1.0 16.0 ± 0.3 0.3 1.55 ± 0.1 7.6 ± 0.1 12.0 ± 0.1 +2.0 16.4 -0.0 Packing : 500 pcs/reel TAPING DIRECTION PS7221-2A-F3 PS7221-2A-F4 PS7221-2A RECOMMENDED SOLDERING CONDITIONS (1) Infrared reflow soldering • • • • Peak reflow temperature Time of temperature higher than 210 ˚C Number of reflows Flux 235 ˚C (package surface temperature) 30 seconds or less Three Rosin flux containing small amount of chlorine (The flux with a max. chlorine content of 0.2 Wt % is recommended Package Surface Temperature T (˚C) Recommended Temperature Profile of Infrared Reflow (heating) to 10 s 235 ˚C (peak temperature) 210 ˚C to 30 s 100 to 160 ˚C 60 to 120 s (preheating) Time (s) (2) Dip soldering • Temperature 260 ˚C or below (molten solder temperature) • Time 10 seconds or less • Number of times One • Flux Rosin flux containing small amount of chlorine (The flux with a max. chlorine content of 0.2 Wt % is recommended.) (3) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. • Avoid shorting between portion of frame and leads. * * *: Portion of frame EXCLUSIVE NORTH AMERICAN AGENT FOR RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279 24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) • Internet: http://WWW.CEL.COM 08/15/2001 DATA SUBJECT TO CHANGE WITHOUT NOTICE